Commit 0468df46 authored by Frank Li's avatar Frank Li Committed by Shawn Guo

arm64: dts: imx8qm-mek: add fec2 support

Add fec2 support.
Signed-off-by: default avatarFrank Li <Frank.Li@nxp.com>
Signed-off-by: default avatarShawn Guo <shawnguo@kernel.org>
parent 6e7e34a2
......@@ -40,6 +40,15 @@ reg_usdhc2_vmmc: usdhc2-vmmc {
enable-active-high;
};
reg_fec2_supply: regulator-fec2-nvcc {
compatible = "regulator-fixed";
regulator-name = "fec2_nvcc";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
gpio = <&max7322 0 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
reg_can01_en: regulator-can01-gen {
compatible = "regulator-fixed";
regulator-name = "can01-en";
......@@ -334,6 +343,19 @@ ethphy1: ethernet-phy@1 {
};
};
&fec2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_fec2>;
phy-mode = "rgmii-txid";
phy-handle = <&ethphy1>;
phy-supply = <&reg_fec2_supply>;
nvmem-cells = <&fec_mac1>;
nvmem-cell-names = "mac-address";
rx-internal-delay-ps = <2000>;
fsl,magic-packet;
status = "okay";
};
&usdhc1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usdhc1>;
......@@ -500,6 +522,24 @@ IMX8QM_QSPI0B_SS1_B_LSIO_QSPI0B_SS1_B 0x06000021
>;
};
pinctrl_fec2: fec2grp {
fsl,pins = <
IMX8QM_COMP_CTL_GPIO_1V8_3V3_ENET_ENETA_PAD 0x000014a0
IMX8QM_ENET1_RGMII_TX_CTL_CONN_ENET1_RGMII_TX_CTL 0x00000060
IMX8QM_ENET1_RGMII_TXC_CONN_ENET1_RGMII_TXC 0x00000060
IMX8QM_ENET1_RGMII_TXD0_CONN_ENET1_RGMII_TXD0 0x00000060
IMX8QM_ENET1_RGMII_TXD1_CONN_ENET1_RGMII_TXD1 0x00000060
IMX8QM_ENET1_RGMII_TXD2_CONN_ENET1_RGMII_TXD2 0x00000060
IMX8QM_ENET1_RGMII_TXD3_CONN_ENET1_RGMII_TXD3 0x00000060
IMX8QM_ENET1_RGMII_RXC_CONN_ENET1_RGMII_RXC 0x00000060
IMX8QM_ENET1_RGMII_RX_CTL_CONN_ENET1_RGMII_RX_CTL 0x00000060
IMX8QM_ENET1_RGMII_RXD0_CONN_ENET1_RGMII_RXD0 0x00000060
IMX8QM_ENET1_RGMII_RXD1_CONN_ENET1_RGMII_RXD1 0x00000060
IMX8QM_ENET1_RGMII_RXD2_CONN_ENET1_RGMII_RXD2 0x00000060
IMX8QM_ENET1_RGMII_RXD3_CONN_ENET1_RGMII_RXD3 0x00000060
>;
};
pinctrl_flexcan1: flexcan0grp {
fsl,pins = <
IMX8QM_FLEXCAN0_TX_DMA_FLEXCAN0_TX 0x21
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment