Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Olof Johansson:
 "Another batch of fixes for ARM SoC platforms.  Most are smaller fixes.

  Two areas that are worth pointing out are:

   - OMAP had a handful of changes to voltage specs that caused a bit of
     churn, most of volume of change in this branch is due to this.

   - There are a couple of _rcuidle fixes from Paul that touch common
     code and came in through the OMAP tree since they were the ones who
     saw the problems.

 The rest is smaller changes across a handful of platforms"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (36 commits)
  ARM: dts: STi: stih407-family: Disable reserved-memory co-processor nodes
  ARM: dts: am437x-sk-evm: Reduce i2c0 bus speed for tps65218
  ARM: OMAP2+: timer: add probe for clocksources
  ARM: OMAP1: fix ams-delta FIQ handler to work with sparse IRQ
  memory: omap-gpmc: Fix omap gpmc EXTRADELAY timing
  arm: Use _rcuidle for smp_cross_call() tracepoints
  MAINTAINERS: Add myself as reviewer of ARM FSL/NXP
  ARM: OMAP: DRA7: powerdomain data: Remove unused pwrsts_mem_ret
  ARM: OMAP: DRA7: powerdomain data: Remove unused pwrsts_logic_ret
  ARM: OMAP: DRA7: powerdomain data: Set L3init and L4per to ON
  ARM: imx6ul: Fix Micrel PHY mask
  ARM: OMAP2+: Select OMAP_INTERCONNECT for SOC_AM43XX
  ARM: dts: DRA74x: fix DSS PLL2 addresses
  ARM: OMAP2: Enable Errata 430973 for OMAP3
  ARM: dts: socfpga: Add missing PHY phandle
  ARM: dts: exynos: Fix port nodes names for Exynos5420 Peach Pit board
  ARM: dts: exynos: Fix port nodes names for Exynos5250 Snow board
  ARM: dts: sun6i: yones-toptech-bs1078-v2: Drop constraints on dc1sw regulator
  ARM: dts: sun6i: primo81: Drop constraints on dc1sw regulator
  ARM: dts: sunxi: Add OLinuXino Lime2 eMMC to the Makefile
  ...

MAINTAINERS

@@ -1159,6 +1159,7 @@ F:	arch/arm/mach-footbridge/
 ARM/FREESCALE IMX / MXC ARM ARCHITECTURE
 M:	Shawn Guo <shawnguo@kernel.org>
 M:	Sascha Hauer <kernel@pengutronix.de>
+R:	Fabio Estevam <fabio.estevam@nxp.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git

arch/arm/boot/dts/Makefile

@@ -741,6 +741,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
 	sun7i-a20-olimex-som-evb.dtb \
 	sun7i-a20-olinuxino-lime.dtb \
 	sun7i-a20-olinuxino-lime2.dtb \
+	sun7i-a20-olinuxino-lime2-emmc.dtb \
 	sun7i-a20-olinuxino-micro.dtb \
 	sun7i-a20-orangepi.dtb \
 	sun7i-a20-orangepi-mini.dtb \

arch/arm/boot/dts/am437x-sk-evm.dts

@@ -418,7 +418,7 @@ &i2c0 {
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0_pins>;
-	clock-frequency = <400000>;
+	clock-frequency = <100000>;
 
 	tps@24 {
 		compatible = "ti,tps65218";

arch/arm/boot/dts/am57xx-idk-common.dtsi

@@ -60,10 +60,26 @@ tps659038: tps659038@58 {
 
 		tps659038_pmic {
 			compatible = "ti,tps659038-pmic";
+
+			smps12-in-supply = <&vmain>;
+			smps3-in-supply = <&vmain>;
+			smps45-in-supply = <&vmain>;
+			smps6-in-supply = <&vmain>;
+			smps7-in-supply = <&vmain>;
+			smps8-in-supply = <&vmain>;
+			smps9-in-supply = <&vmain>;
+			ldo1-in-supply = <&vmain>;
+			ldo2-in-supply = <&vmain>;
+			ldo3-in-supply = <&vmain>;
+			ldo4-in-supply = <&vmain>;
+			ldo9-in-supply = <&vmain>;
+			ldoln-in-supply = <&vmain>;
+			ldousb-in-supply = <&vmain>;
+			ldortc-in-supply = <&vmain>;
+
 			regulators {
 				smps12_reg: smps12 {
 					/* VDD_MPU */
-					vin-supply = <&vmain>;
 					regulator-name = "smps12";
 					regulator-min-microvolt = <850000>;
 					regulator-max-microvolt = <1250000>;
@@ -73,7 +89,6 @@ smps12_reg: smps12 {
 
 				smps3_reg: smps3 {
 					/* VDD_DDR EMIF1 EMIF2 */
-					vin-supply = <&vmain>;
 					regulator-name = "smps3";
 					regulator-min-microvolt = <1350000>;
 					regulator-max-microvolt = <1350000>;
@@ -84,7 +99,6 @@ smps3_reg: smps3 {
 				smps45_reg: smps45 {
 					/* VDD_DSPEVE on AM572 */
 					/* VDD_IVA + VDD_DSP on AM571 */
-					vin-supply = <&vmain>;
 					regulator-name = "smps45";
 					regulator-min-microvolt = <850000>;
 					regulator-max-microvolt = <1250000>;
@@ -94,7 +108,6 @@ smps45_reg: smps45 {
 
 				smps6_reg: smps6 {
 					/* VDD_GPU */
-					vin-supply = <&vmain>;
 					regulator-name = "smps6";
 					regulator-min-microvolt = <850000>;
 					regulator-max-microvolt = <1250000>;
@@ -104,7 +117,6 @@ smps6_reg: smps6 {
 
 				smps7_reg: smps7 {
 					/* VDD_CORE */
-					vin-supply = <&vmain>;
 					regulator-name = "smps7";
 					regulator-min-microvolt = <850000>;
 					regulator-max-microvolt = <1150000>;
@@ -115,13 +127,11 @@ smps7_reg: smps7 {
 				smps8_reg: smps8 {
 					/* 5728 - VDD_IVAHD */
 					/* 5718 - N.C. test point */
-					vin-supply = <&vmain>;
 					regulator-name = "smps8";
 				};
 
 				smps9_reg: smps9 {
 					/* VDD_3_3D */
-					vin-supply = <&vmain>;
 					regulator-name = "smps9";
 					regulator-min-microvolt = <3300000>;
 					regulator-max-microvolt = <3300000>;
@@ -132,7 +142,6 @@ smps9_reg: smps9 {
 				ldo1_reg: ldo1 {
 					/* VDDSHV8 - VSDMMC  */
 					/* NOTE: on rev 1.3a, data supply */
-					vin-supply = <&vmain>;
 					regulator-name = "ldo1";
 					regulator-min-microvolt = <1800000>;
 					regulator-max-microvolt = <3300000>;
@@ -142,7 +151,6 @@ ldo1_reg: ldo1 {
 
 				ldo2_reg: ldo2 {
 					/* VDDSH18V */
-					vin-supply = <&vmain>;
 					regulator-name = "ldo2";
 					regulator-min-microvolt = <1800000>;
 					regulator-max-microvolt = <1800000>;
@@ -152,7 +160,6 @@ ldo2_reg: ldo2 {
 
 				ldo3_reg: ldo3 {
 					/* R1.3a 572x V1_8PHY_LDO3: USB, SATA */
-					vin-supply = <&vmain>;
 					regulator-name = "ldo3";
 					regulator-min-microvolt = <1800000>;
 					regulator-max-microvolt = <1800000>;
@@ -162,7 +169,6 @@ ldo3_reg: ldo3 {
 
 				ldo4_reg: ldo4 {
 					/* R1.3a 572x V1_8PHY_LDO4: PCIE, HDMI*/
-					vin-supply = <&vmain>;
 					regulator-name = "ldo4";
 					regulator-min-microvolt = <1800000>;
 					regulator-max-microvolt = <1800000>;
@@ -174,7 +180,6 @@ ldo4_reg: ldo4 {
 
 				ldo9_reg: ldo9 {
 					/* VDD_RTC  */
-					vin-supply = <&vmain>;
 					regulator-name = "ldo9";
 					regulator-min-microvolt = <840000>;
 					regulator-max-microvolt = <1160000>;
@@ -184,7 +189,6 @@ ldo9_reg: ldo9 {
 
 				ldoln_reg: ldoln {
 					/* VDDA_1V8_PLL */
-					vin-supply = <&vmain>;
 					regulator-name = "ldoln";
 					regulator-min-microvolt = <1800000>;
 					regulator-max-microvolt = <1800000>;
@@ -194,7 +198,6 @@ ldoln_reg: ldoln {
 
 				ldousb_reg: ldousb {
 					/* VDDA_3V_USB: VDDA_USBHS33 */
-					vin-supply = <&vmain>;
 					regulator-name = "ldousb";
 					regulator-min-microvolt = <3300000>;
 					regulator-max-microvolt = <3300000>;
@@ -204,7 +207,6 @@ ldousb_reg: ldousb {
 
 				ldortc_reg: ldortc {
 					/* VDDA_RTC  */
-					vin-supply = <&vmain>;
 					regulator-name = "ldortc";
 					regulator-min-microvolt = <1800000>;
 					regulator-max-microvolt = <1800000>;

arch/arm/boot/dts/dm8148-evm.dts

@@ -93,6 +93,10 @@ partition@0x780000 {
 	};
 };
 
+&mmc1 {
+        status = "disabled";
+};
+
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&sd1_pins>;
@@ -101,6 +105,10 @@ &mmc2 {
 	cd-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
 };
 
+&mmc3 {
+        status = "disabled";
+};
+
 &pincntl {
 	sd1_pins: pinmux_sd1_pins {
 		pinctrl-single,pins = <

arch/arm/boot/dts/dm8148-t410.dts

@@ -45,6 +45,14 @@ &cpsw_emac1 {
 	phy-mode = "rgmii";
 };
 
+&mmc1 {
+	status = "disabled";
+};
+
+&mmc2 {
+	status = "disabled";
+};
+
 &mmc3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&sd2_pins>;
@@ -53,6 +61,7 @@ &mmc3 {
 	dmas = <&edma_xbar 8 0 1	/* use SDTXEVT1 instead of MCASP0TX */
 		&edma_xbar 9 0 2>;	/* use SDRXEVT1 instead of MCASP0RX */
 	dma-names = "tx", "rx";
+	non-removable;
 };
 
 &pincntl {

arch/arm/boot/dts/dra7.dtsi

@@ -1451,6 +1451,8 @@ gpmc: gpmc@50000000 {
 			ti,hwmods = "gpmc";
 			reg = <0x50000000 0x37c>;      /* device IO registers */
 			interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&edma_xbar 4 0>;
+			dma-names = "rxtx";
 			gpmc,num-cs = <8>;
 			gpmc,num-waitpins = <2>;
 			#address-cells = <2>;

arch/arm/boot/dts/dra74x.dtsi

@@ -107,8 +107,8 @@ &dss {
 	reg = <0x58000000 0x80>,
 	      <0x58004054 0x4>,
 	      <0x58004300 0x20>,
-	      <0x58005054 0x4>,
-	      <0x58005300 0x20>;
+	      <0x58009054 0x4>,
+	      <0x58009300 0x20>;
 	reg-names = "dss", "pll1_clkctrl", "pll1",
 		    "pll2_clkctrl", "pll2";
 

arch/arm/boot/dts/exynos5250-snow-common.dtsi

@@ -242,7 +242,7 @@ &dp {
 	hpd-gpios = <&gpx0 7 GPIO_ACTIVE_HIGH>;
 
 	ports {
-		port0 {
+		port {
 			dp_out: endpoint {
 				remote-endpoint = <&bridge_in>;
 			};
@@ -485,13 +485,20 @@ ptn3460: lvds-bridge@20 {
 		edid-emulation = <5>;
 
 		ports {
-			port0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
 				bridge_out: endpoint {
 					remote-endpoint = <&panel_in>;
 				};
 			};
 
-			port1 {
+			port@1 {
+				reg = <1>;
+
 				bridge_in: endpoint {
 					remote-endpoint = <&dp_out>;
 				};

arch/arm/boot/dts/exynos5420-peach-pit.dts

@@ -163,7 +163,7 @@ &dp {
 	hpd-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>;
 
 	ports {
-		port0 {
+		port {
 			dp_out: endpoint {
 				remote-endpoint = <&bridge_in>;
 			};
@@ -631,13 +631,20 @@ ps8625: lvds-bridge@48 {
 		use-external-pwm;
 
 		ports {
-			port0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
 				bridge_out: endpoint {
 					remote-endpoint = <&panel_in>;
 				};
 			};
 
-			port1 {
+			port@1 {
+				reg = <1>;
+
 				bridge_in: endpoint {
 					remote-endpoint = <&dp_out>;
 				};

arch/arm/boot/dts/omap3-evm-37xx.dts

@@ -85,7 +85,7 @@ mmc2_pins: pinmux_mmc2_pins {
 			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk.sdmmc2_clk */
 			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd.sdmmc2_cmd */
 			OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat0.sdmmc2_dat0 */
-			OMAP3_CORE1_IOPAD(0x215e, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
+			OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
 			OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat2.sdmmc2_dat2 */
 			OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat3.sdmmc2_dat3 */
 		>;

arch/arm/boot/dts/omap3-igep.dtsi

@@ -188,6 +188,7 @@ &mmc1 {
 	vmmc-supply = <&vmmc1>;
 	vmmc_aux-supply = <&vsim>;
 	bus-width = <4>;
+	cd-gpios = <&twl_gpio 0 GPIO_ACTIVE_LOW>;
 };
 
 &mmc3 {

arch/arm/boot/dts/omap3-igep0020-common.dtsi

@@ -194,6 +194,12 @@ OMAP3630_CORE2_IOPAD(0x25f6, PIN_OUTPUT | MUX_MODE4) /* etk_d13.gpio_27 */
 			OMAP3630_CORE2_IOPAD(0x25f8, PIN_OUTPUT | MUX_MODE4) /* etk_d14.gpio_28 */
 		>;
 	};
+
+	mmc1_wp_pins: pinmux_mmc1_cd_pins {
+		pinctrl-single,pins = <
+			OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT | MUX_MODE4)   /* etk_d15.gpio_29 */
+		>;
+	};
 };
 
 &i2c3 {
@@ -250,3 +256,8 @@ dpi_out: endpoint {
 		};
 	};
 };
+
+&mmc1 {
+	pinctrl-0 = <&mmc1_pins &mmc1_wp_pins>;
+	wp-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;	/* gpio_29 */
+};

arch/arm/boot/dts/omap3-n900.dts

@@ -288,7 +288,7 @@ ssi_pins: pinmux_ssi {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT_PULLUP | MUX_MODE1)	/* ssi1_rdy_tx */
 			OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE1)		/* ssi1_flag_tx */
-			OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* ssi1_wake_tx (cawake) */
+			OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | MUX_MODE4)		/* ssi1_wake_tx (cawake) */
 			OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE1)		/* ssi1_dat_tx */
 			OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT | MUX_MODE1)		/* ssi1_dat_rx */
 			OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE1)		/* ssi1_flag_rx */
@@ -300,7 +300,7 @@ OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | MUX_MODE1)		/* ssi1_wake */
 	modem_pins: pinmux_modem {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE4)		/* gpio 70 => cmt_apeslpx */
-			OMAP3_CORE1_IOPAD(0x20e0, PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* gpio 72 => ape_rst_rq */
+			OMAP3_CORE1_IOPAD(0x20e0, PIN_INPUT | MUX_MODE4)		/* gpio 72 => ape_rst_rq */
 			OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE4)		/* gpio 73 => cmt_rst_rq */
 			OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE4)		/* gpio 74 => cmt_en */
 			OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE4)		/* gpio 75 => cmt_rst */

arch/arm/boot/dts/omap3-n950-n9.dtsi

@@ -97,7 +97,7 @@ ssi_pins: pinmux_ssi_pins {
 			OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE1)            /* ssi1_dat_tx */
 			OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE1)            /* ssi1_flag_tx */
 			OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT_PULLUP | MUX_MODE1)      /* ssi1_rdy_tx */
-			OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* ssi1_wake_tx (cawake) */
+			OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | MUX_MODE4)	/* ssi1_wake_tx (cawake) */
 			OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT | MUX_MODE1)             /* ssi1_dat_rx */
 			OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE1)             /* ssi1_flag_rx */
 			OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | MUX_MODE1)            /* ssi1_rdy_rx */
@@ -110,7 +110,7 @@ ssi_pins_idle: pinmux_ssi_pins_idle {
 			OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE7)            /* ssi1_dat_tx */
 			OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE7)            /* ssi1_flag_tx */
 			OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT_PULLDOWN | MUX_MODE7)    /* ssi1_rdy_tx */
-			OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* ssi1_wake_tx (cawake) */
+			OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | MUX_MODE4)	/* ssi1_wake_tx (cawake) */
 			OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT | MUX_MODE7)             /* ssi1_dat_rx */
 			OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE7)             /* ssi1_flag_rx */
 			OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | MUX_MODE4)            /* ssi1_rdy_rx */
@@ -120,7 +120,7 @@ OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | MUX_MODE7)            /* ssi1_wake */
 
 	modem_pins1: pinmux_modem_core1_pins {
 		pinctrl-single,pins = <
-			OMAP3_CORE1_IOPAD(0x207a, PIN_INPUT | WAKEUP_EN | MUX_MODE4) /* gpio_34 (ape_rst_rq) */
+			OMAP3_CORE1_IOPAD(0x207a, PIN_INPUT | MUX_MODE4)	/* gpio_34 (ape_rst_rq) */
 			OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE4)            /* gpio_88 (cmt_rst_rq) */
 			OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE4)            /* gpio_93 (cmt_apeslpx) */
 		>;

arch/arm/boot/dts/omap3-zoom3.dts

@@ -98,7 +98,7 @@ uart2_pins: pinmux_uart2_pins {
 		pinctrl-single,pins = <
                         OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart2_cts.uart2_cts */
                         OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0)		/* uart2_rts.uart2_rts */
-                        OMAP3_CORE1_IOPAD(0x217a, WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */
+                        OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0)		/* uart2_rx.uart2_rx */
                         OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0)		/* uart2_tx.uart2_tx */
 		>;
 	};
@@ -107,7 +107,7 @@ uart3_pins: pinmux_uart3_pins {
 		pinctrl-single,pins = <
                         OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* uart3_cts_rctx.uart3_cts_rctx */
                         OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE0)		/* uart3_rts_sd.uart3_rts_sd */
-                        OMAP3_CORE1_IOPAD(0x219e, WAKEUP_EN | PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */
+                        OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0)		/* uart3_rx_irrx.uart3_rx_irrx */
                         OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)		/* uart3_tx_irtx.uart3_tx_irtx */
 		>;
 	};
@@ -125,7 +125,7 @@ mmc3_2_pins: pinmux_mmc3_2_pins {
 		pinctrl-single,pins = <
 			OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_clk.sdmmc3_clk */
 			OMAP3630_CORE2_IOPAD(0x25e4, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d4.sdmmc3_dat0 */
-			OMAP3630_CORE2_IOPAD(0x25e6, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE2) /* etk_d5.sdmmc3_dat1 */
+			OMAP3630_CORE2_IOPAD(0x25e6, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d5.sdmmc3_dat1 */
 			OMAP3630_CORE2_IOPAD(0x25e8, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d6.sdmmc3_dat2 */
 			OMAP3630_CORE2_IOPAD(0x25e2, PIN_INPUT_PULLUP | MUX_MODE2)	/* etk_d3.sdmmc3_dat3 */
 		>;

arch/arm/boot/dts/omap5-board-common.dtsi

@@ -14,6 +14,29 @@ aliases {
 		display0 = &hdmi0;
 	};
 
+	vmain: fixedregulator-vmain {
+		compatible = "regulator-fixed";
+		regulator-name = "vmain";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vsys_cobra: fixedregulator-vsys_cobra {
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_cobra";
+		vin-supply = <&vmain>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vdds_1v8_main: fixedregulator-vdds_1v8_main {
+		compatible = "regulator-fixed";
+		regulator-name = "vdds_1v8_main";
+		vin-supply = <&smps7_reg>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
 	vmmcsd_fixed: fixedregulator-mmcsd {
 		compatible = "regulator-fixed";
 		regulator-name = "vmmcsd_fixed";
@@ -309,7 +332,7 @@ OMAP5_IOPAD(0x05a, PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */
 
 	wlcore_irq_pin: pinmux_wlcore_irq_pin {
 		pinctrl-single,pins = <
-			OMAP5_IOPAD(0x40, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE6)	/* llia_wakereqin.gpio1_wk14 */
+			OMAP5_IOPAD(0x40, PIN_INPUT_PULLUP | MUX_MODE6)	/* llia_wakereqin.gpio1_wk14 */
 		>;
 	};
 };
@@ -409,6 +432,26 @@ palmas_pmic {
 
 			ti,ldo6-vibrator;
 
+			smps123-in-supply = <&vsys_cobra>;
+			smps45-in-supply = <&vsys_cobra>;
+			smps6-in-supply = <&vsys_cobra>;
+			smps7-in-supply = <&vsys_cobra>;
+			smps8-in-supply = <&vsys_cobra>;
+			smps9-in-supply = <&vsys_cobra>;
+			smps10_out2-in-supply = <&vsys_cobra>;
+			smps10_out1-in-supply = <&vsys_cobra>;
+			ldo1-in-supply = <&vsys_cobra>;
+			ldo2-in-supply = <&vsys_cobra>;
+			ldo3-in-supply = <&vdds_1v8_main>;
+			ldo4-in-supply = <&vdds_1v8_main>;
+			ldo5-in-supply = <&vsys_cobra>;
+			ldo6-in-supply = <&vdds_1v8_main>;
+			ldo7-in-supply = <&vsys_cobra>;
+			ldo8-in-supply = <&vsys_cobra>;
+			ldo9-in-supply = <&vmmcsd_fixed>;
+			ldoln-in-supply = <&vsys_cobra>;
+			ldousb-in-supply = <&vsys_cobra>;
+
 			regulators {
 				smps123_reg: smps123 {
 					/* VDD_OPP_MPU */
@@ -600,7 +643,8 @@ twl6040: twl@4b {
 		pinctrl-0 = <&twl6040_pins>;
 
 		interrupts = <GIC_SPI 119 IRQ_TYPE_NONE>; /* IRQ_SYS_2N cascaded to gic */
-		ti,audpwron-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>;  /* gpio line 141 */
+
+		/* audpwron gpio defined in the board specific dts */
 
 		vio-supply = <&smps7_reg>;
 		v2v1-supply = <&smps9_reg>;

arch/arm/boot/dts/omap5-igep0050.dts

@@ -35,6 +35,22 @@ tca6416: tca6416@21 {
 	};
 };
 
+/* LDO4 is VPP1 - ball AD9 */
+&ldo4_reg {
+	regulator-min-microvolt = <2000000>;
+	regulator-max-microvolt = <2000000>;
+};
+
+/*
+ * LDO7 is used for HDMI: VDDA_DSIPORTA - ball AA33, VDDA_DSIPORTC - ball AE33,
+ * VDDA_HDMI - ball AN25
+ */
+&ldo7_reg {
+	status = "okay";
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+};
+
 &omap5_pmx_core {
 	i2c4_pins: pinmux_i2c4_pins {
 		pinctrl-single,pins = <
@@ -52,3 +68,13 @@ &tpd12s015 {
 		<&gpio7 3 0>;		/* 195, SDA */
 };
 
+&twl6040 {
+	ti,audpwron-gpio = <&gpio5 16 GPIO_ACTIVE_HIGH>;  /* gpio line 144 */
+};
+
+&twl6040_pins {
+	pinctrl-single,pins = <
+		OMAP5_IOPAD(0x1c4, PIN_OUTPUT | MUX_MODE6)	/* mcspi1_somi.gpio5_144 */
+		OMAP5_IOPAD(0x1ca, PIN_OUTPUT | MUX_MODE6)	/* perslimbus2_clock.gpio5_145 */
+	>;
+};

arch/arm/boot/dts/omap5-uevm.dts

@@ -51,3 +51,13 @@ &tpd12s015 {
 		<&gpio9 1 GPIO_ACTIVE_HIGH>,	/* TCA6424A P00, LS OE */
 		<&gpio7 1 GPIO_ACTIVE_HIGH>;	/* GPIO 193, HPD */
 };
+
+&twl6040 {
+	ti,audpwron-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>;  /* gpio line 141 */
+};
+
+&twl6040_pins {
+	pinctrl-single,pins = <
+		OMAP5_IOPAD(0x1be, PIN_OUTPUT | MUX_MODE6)	/* mcspi1_somi.gpio5_141 */
+	>;
+};

arch/arm/boot/dts/socfpga_cyclone5_vining_fpga.dts

@@ -136,6 +136,7 @@ regulator-usb-nrst {
 &gmac1 {
 	status = "okay";
 	phy-mode = "rgmii";
+	phy-handle = <&phy1>;
 
 	snps,reset-gpio = <&porta 0 GPIO_ACTIVE_LOW>;
 	snps,reset-active-low;

arch/arm/boot/dts/stih407-family.dtsi

@@ -24,18 +24,21 @@ gp0_reserved: rproc@40000000 {
 			compatible = "shared-dma-pool";
 			reg = <0x40000000 0x01000000>;
 			no-map;
+			status = "disabled";
 		};
 
 		gp1_reserved: rproc@41000000 {
 			compatible = "shared-dma-pool";
 			reg = <0x41000000 0x01000000>;
 			no-map;
+			status = "disabled";
 		};
 
 		audio_reserved: rproc@42000000 {
 			compatible = "shared-dma-pool";
 			reg = <0x42000000 0x01000000>;
 			no-map;
+			status = "disabled";
 		};
 
 		dmu_reserved: rproc@43000000 {

arch/arm/boot/dts/sun6i-a31s-primo81.dts

@@ -176,8 +176,6 @@ &reg_aldo3 {
 };
 
 &reg_dc1sw {
-	regulator-min-microvolt = <3000000>;
-	regulator-max-microvolt = <3000000>;
 	regulator-name = "vcc-lcd";
 };
 

arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts

@@ -135,8 +135,6 @@ &reg_aldo3 {
 
 &reg_dc1sw {
 	regulator-name = "vcc-lcd-usb2";
-	regulator-min-microvolt = <3000000>;
-	regulator-max-microvolt = <3000000>;
 };
 
 &reg_dc5ldo {

arch/arm/configs/exynos_defconfig

@@ -82,6 +82,7 @@ CONFIG_TOUCHSCREEN_MMS114=y
 CONFIG_INPUT_MISC=y
 CONFIG_INPUT_MAX77693_HAPTIC=y
 CONFIG_INPUT_MAX8997_HAPTIC=y
+CONFIG_KEYBOARD_SAMSUNG=y
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_SAMSUNG=y
 CONFIG_SERIAL_SAMSUNG_CONSOLE=y

arch/arm/configs/multi_v7_defconfig

@@ -264,6 +264,7 @@ CONFIG_KEYBOARD_TEGRA=y
 CONFIG_KEYBOARD_SPEAR=y
 CONFIG_KEYBOARD_ST_KEYSCAN=y
 CONFIG_KEYBOARD_CROS_EC=m
+CONFIG_KEYBOARD_SAMSUNG=m
 CONFIG_MOUSE_PS2_ELANTECH=y
 CONFIG_MOUSE_CYAPA=m
 CONFIG_MOUSE_ELAN_I2C=y

arch/arm/kernel/smp.c

@@ -486,7 +486,7 @@ static const char *ipi_types[NR_IPI] __tracepoint_string = {
 
 static void smp_cross_call(const struct cpumask *target, unsigned int ipinr)
 {
-	trace_ipi_raise(target, ipi_types[ipinr]);
+	trace_ipi_raise_rcuidle(target, ipi_types[ipinr]);
 	__smp_cross_call(target, ipinr);
 }
 

arch/arm/mach-exynos/Kconfig

@@ -61,7 +61,6 @@ config ARCH_EXYNOS4
 	select CLKSRC_SAMSUNG_PWM if CPU_EXYNOS4210
 	select CPU_EXYNOS4210
 	select GIC_NON_BANKED
-	select KEYBOARD_SAMSUNG if INPUT_KEYBOARD
 	select MIGHT_HAVE_CACHE_L2X0
 	help
 	  Samsung EXYNOS4 (Cortex-A9) SoC based systems

arch/arm/mach-imx/mach-imx6ul.c

@@ -46,7 +46,7 @@ static int ksz8081_phy_fixup(struct phy_device *dev)
 static void __init imx6ul_enet_phy_init(void)
 {
 	if (IS_BUILTIN(CONFIG_PHYLIB))
-		phy_register_fixup_for_uid(PHY_ID_KSZ8081, 0xffffffff,
+		phy_register_fixup_for_uid(PHY_ID_KSZ8081, MICREL_PHY_ID_MASK,
 					   ksz8081_phy_fixup);
 }
 

arch/arm/mach-omap1/ams-delta-fiq-handler.S

@@ -43,8 +43,8 @@
 #define OTHERS_MASK			(MODEM_IRQ_MASK | HOOK_SWITCH_MASK)
 
 /* IRQ handler register bitmasks */
-#define DEFERRED_FIQ_MASK		(0x1 << (INT_DEFERRED_FIQ % IH2_BASE))
-#define GPIO_BANK1_MASK  		(0x1 << INT_GPIO_BANK1)
+#define DEFERRED_FIQ_MASK		OMAP_IRQ_BIT(INT_DEFERRED_FIQ)
+#define GPIO_BANK1_MASK  		OMAP_IRQ_BIT(INT_GPIO_BANK1)
 
 /* Driver buffer byte offsets */
 #define BUF_MASK			(FIQ_MASK * 4)
@@ -110,7 +110,7 @@ ENTRY(qwerty_fiqin_start)
 	mov r8, #2				@ reset FIQ agreement
 	str r8, [r12, #IRQ_CONTROL_REG_OFFSET]
 
-	cmp r10, #INT_GPIO_BANK1		@ is it GPIO bank interrupt?
+	cmp r10, #(INT_GPIO_BANK1 - NR_IRQS_LEGACY)	@ is it GPIO interrupt?
 	beq gpio				@ yes - process it
 
 	mov r8, #1

arch/arm/mach-omap1/ams-delta-fiq.c

@@ -109,7 +109,8 @@ void __init ams_delta_init_fiq(void)
 	 * Since no set_type() method is provided by OMAP irq chip,
 	 * switch to edge triggered interrupt type manually.
 	 */
-	offset = IRQ_ILR0_REG_OFFSET + INT_DEFERRED_FIQ * 0x4;
+	offset = IRQ_ILR0_REG_OFFSET +
+			((INT_DEFERRED_FIQ - NR_IRQS_LEGACY) & 0x1f) * 0x4;
 	val = omap_readl(DEFERRED_FIQ_IH_BASE + offset) & ~(1 << 1);
 	omap_writel(val, DEFERRED_FIQ_IH_BASE + offset);
 
@@ -149,7 +150,7 @@ void __init ams_delta_init_fiq(void)
 	/*
 	 * Redirect GPIO interrupts to FIQ
 	 */
-	offset = IRQ_ILR0_REG_OFFSET + INT_GPIO_BANK1 * 0x4;
+	offset = IRQ_ILR0_REG_OFFSET + (INT_GPIO_BANK1 - NR_IRQS_LEGACY) * 0x4;
 	val = omap_readl(OMAP_IH1_BASE + offset) | 1;
 	omap_writel(val, OMAP_IH1_BASE + offset);
 }

arch/arm/mach-omap1/include/mach/ams-delta-fiq.h

@@ -14,6 +14,8 @@
 #ifndef __AMS_DELTA_FIQ_H
 #define __AMS_DELTA_FIQ_H
 
+#include <mach/irqs.h>
+
 /*
  * Interrupt number used for passing control from FIQ to IRQ.
  * IRQ12, described as reserved, has been selected.

arch/arm/mach-omap2/Kconfig

@@ -17,6 +17,7 @@ config ARCH_OMAP3
 	select PM_OPP if PM
 	select PM if CPU_IDLE
 	select SOC_HAS_OMAP2_SDRC
+	select ARM_ERRATA_430973
 
 config ARCH_OMAP4
 	bool "TI OMAP4"
@@ -36,6 +37,7 @@ config ARCH_OMAP4
 	select PM if CPU_IDLE
 	select ARM_ERRATA_754322
 	select ARM_ERRATA_775420
+	select OMAP_INTERCONNECT
 
 config SOC_OMAP5
 	bool "TI OMAP5"
@@ -67,6 +69,8 @@ config SOC_AM43XX
 	select HAVE_ARM_SCU
 	select GENERIC_CLOCKEVENTS_BROADCAST
 	select HAVE_ARM_TWD
+	select ARM_ERRATA_754322
+	select ARM_ERRATA_775420
 
 config SOC_DRA7XX
 	bool "TI DRA7XX"
@@ -240,4 +244,12 @@ endmenu
 
 endif
 
+config OMAP5_ERRATA_801819
+	bool "Errata 801819: An eviction from L1 data cache might stall indefinitely"
+	depends on SOC_OMAP5 || SOC_DRA7XX
+	help
+	  A livelock can occur in the L2 cache arbitration that might prevent
+	  a snoop from completing. Under certain conditions this can cause the
+	  system to deadlock.
+
 endmenu

arch/arm/mach-omap2/omap-secure.h

@@ -46,6 +46,7 @@
 
 #define OMAP5_DRA7_MON_SET_CNTFRQ_INDEX	0x109
 #define OMAP5_MON_AMBA_IF_INDEX		0x108
+#define OMAP5_DRA7_MON_SET_ACR_INDEX	0x107
 
 /* Secure PPA(Primary Protected Application) APIs */
 #define OMAP4_PPA_L2_POR_INDEX		0x23

arch/arm/mach-omap2/omap-smp.c

@@ -50,6 +50,39 @@ void __iomem *omap4_get_scu_base(void)
 	return scu_base;
 }
 
+#ifdef CONFIG_OMAP5_ERRATA_801819
+void omap5_erratum_workaround_801819(void)
+{
+	u32 acr, revidr;
+	u32 acr_mask;
+
+	/* REVIDR[3] indicates erratum fix available on silicon */
+	asm volatile ("mrc p15, 0, %0, c0, c0, 6" : "=r" (revidr));
+	if (revidr & (0x1 << 3))
+		return;
+
+	asm volatile ("mrc p15, 0, %0, c1, c0, 1" : "=r" (acr));
+	/*
+	 * BIT(27) - Disables streaming. All write-allocate lines allocate in
+	 * the L1 or L2 cache.
+	 * BIT(25) - Disables streaming. All write-allocate lines allocate in
+	 * the L1 cache.
+	 */
+	acr_mask = (0x3 << 25) | (0x3 << 27);
+	/* do we already have it done.. if yes, skip expensive smc */
+	if ((acr & acr_mask) == acr_mask)
+		return;
+
+	acr |= acr_mask;
+	omap_smc1(OMAP5_DRA7_MON_SET_ACR_INDEX, acr);
+
+	pr_debug("%s: ARM erratum workaround 801819 applied on CPU%d\n",
+		 __func__, smp_processor_id());
+}
+#else
+static inline void omap5_erratum_workaround_801819(void) { }
+#endif
+
 static void omap4_secondary_init(unsigned int cpu)
 {
 	/*
@@ -64,12 +97,15 @@ static void omap4_secondary_init(unsigned int cpu)
 		omap_secure_dispatcher(OMAP4_PPA_CPU_ACTRL_SMP_INDEX,
 							4, 0, 0, 0, 0, 0);
 
+	if (soc_is_omap54xx() || soc_is_dra7xx()) {
 		/*
 		 * Configure the CNTFRQ register for the secondary cpu's which
 		 * indicates the frequency of the cpu local timers.
 		 */
-	if (soc_is_omap54xx() || soc_is_dra7xx())
 		set_cntfreq();
+		/* Configure ACR to disable streaming WA for 801819 */
+		omap5_erratum_workaround_801819();
+	}
 
 	/*
 	 * Synchronise with the boot thread.
@@ -218,6 +254,8 @@ static void __init omap4_smp_prepare_cpus(unsigned int max_cpus)
 
 	if (cpu_is_omap446x())
 		startup_addr = omap4460_secondary_startup;
+	if (soc_is_dra74x() || soc_is_omap54xx())
+		omap5_erratum_workaround_801819();
 
 	/*
 	 * Write the address of secondary startup routine into the

arch/arm/mach-omap2/powerdomain.c

@@ -186,7 +186,8 @@ static int _pwrdm_state_switch(struct powerdomain *pwrdm, int flag)
 			trace_state = (PWRDM_TRACE_STATES_FLAG |
 				       ((next & OMAP_POWERSTATE_MASK) << 8) |
 				       ((prev & OMAP_POWERSTATE_MASK) << 0));
-			trace_power_domain_target(pwrdm->name, trace_state,
+			trace_power_domain_target_rcuidle(pwrdm->name,
+							  trace_state,
 							  smp_processor_id());
 		}
 		break;
@@ -523,7 +524,7 @@ int pwrdm_set_next_pwrst(struct powerdomain *pwrdm, u8 pwrst)
 
 	if (arch_pwrdm && arch_pwrdm->pwrdm_set_next_pwrst) {
 		/* Trace the pwrdm desired target state */
-		trace_power_domain_target(pwrdm->name, pwrst,
+		trace_power_domain_target_rcuidle(pwrdm->name, pwrst,
 						  smp_processor_id());
 		/* Program the pwrdm desired target state */
 		ret = arch_pwrdm->pwrdm_set_next_pwrst(pwrdm, pwrst);

arch/arm/mach-omap2/powerdomains7xx_data.c

@@ -36,14 +36,7 @@ static struct powerdomain iva_7xx_pwrdm = {
 	.prcm_offs	  = DRA7XX_PRM_IVA_INST,
 	.prcm_partition	  = DRA7XX_PRM_PARTITION,
 	.pwrsts		  = PWRSTS_OFF_ON,
-	.pwrsts_logic_ret = PWRSTS_OFF,
 	.banks		  = 4,
-	.pwrsts_mem_ret	= {
-		[0] = PWRSTS_OFF_RET,	/* hwa_mem */
-		[1] = PWRSTS_OFF_RET,	/* sl2_mem */
-		[2] = PWRSTS_OFF_RET,	/* tcm1_mem */
-		[3] = PWRSTS_OFF_RET,	/* tcm2_mem */
-	},
 	.pwrsts_mem_on	= {
 		[0] = PWRSTS_ON,	/* hwa_mem */
 		[1] = PWRSTS_ON,	/* sl2_mem */
@@ -76,12 +69,7 @@ static struct powerdomain ipu_7xx_pwrdm = {
 	.prcm_offs	  = DRA7XX_PRM_IPU_INST,
 	.prcm_partition	  = DRA7XX_PRM_PARTITION,
 	.pwrsts		  = PWRSTS_OFF_ON,
-	.pwrsts_logic_ret = PWRSTS_OFF,
 	.banks		  = 2,
-	.pwrsts_mem_ret	= {
-		[0] = PWRSTS_OFF_RET,	/* aessmem */
-		[1] = PWRSTS_OFF_RET,	/* periphmem */
-	},
 	.pwrsts_mem_on	= {
 		[0] = PWRSTS_ON,	/* aessmem */
 		[1] = PWRSTS_ON,	/* periphmem */
@@ -95,11 +83,7 @@ static struct powerdomain dss_7xx_pwrdm = {
 	.prcm_offs	  = DRA7XX_PRM_DSS_INST,
 	.prcm_partition	  = DRA7XX_PRM_PARTITION,
 	.pwrsts		  = PWRSTS_OFF_ON,
-	.pwrsts_logic_ret = PWRSTS_OFF,
 	.banks		  = 1,
-	.pwrsts_mem_ret	= {
-		[0] = PWRSTS_OFF_RET,	/* dss_mem */
-	},
 	.pwrsts_mem_on	= {
 		[0] = PWRSTS_ON,	/* dss_mem */
 	},
@@ -111,13 +95,8 @@ static struct powerdomain l4per_7xx_pwrdm = {
 	.name		  = "l4per_pwrdm",
 	.prcm_offs	  = DRA7XX_PRM_L4PER_INST,
 	.prcm_partition	  = DRA7XX_PRM_PARTITION,
-	.pwrsts		  = PWRSTS_RET_ON,
-	.pwrsts_logic_ret = PWRSTS_RET,
+	.pwrsts		  = PWRSTS_ON,
 	.banks		  = 2,
-	.pwrsts_mem_ret	= {
-		[0] = PWRSTS_OFF_RET,	/* nonretained_bank */
-		[1] = PWRSTS_OFF_RET,	/* retained_bank */
-	},
 	.pwrsts_mem_on	= {
 		[0] = PWRSTS_ON,	/* nonretained_bank */
 		[1] = PWRSTS_ON,	/* retained_bank */
@@ -132,9 +111,6 @@ static struct powerdomain gpu_7xx_pwrdm = {
 	.prcm_partition	  = DRA7XX_PRM_PARTITION,
 	.pwrsts		  = PWRSTS_OFF_ON,
 	.banks		  = 1,
-	.pwrsts_mem_ret	= {
-		[0] = PWRSTS_OFF_RET,	/* gpu_mem */
-	},
 	.pwrsts_mem_on	= {
 		[0] = PWRSTS_ON,	/* gpu_mem */
 	},
@@ -148,8 +124,6 @@ static struct powerdomain wkupaon_7xx_pwrdm = {
 	.prcm_partition	  = DRA7XX_PRM_PARTITION,
 	.pwrsts		  = PWRSTS_ON,
 	.banks		  = 1,
-	.pwrsts_mem_ret	= {
-	},
 	.pwrsts_mem_on	= {
 		[0] = PWRSTS_ON,	/* wkup_bank */
 	},
@@ -161,15 +135,7 @@ static struct powerdomain core_7xx_pwrdm = {
 	.prcm_offs	  = DRA7XX_PRM_CORE_INST,
 	.prcm_partition	  = DRA7XX_PRM_PARTITION,
 	.pwrsts		  = PWRSTS_ON,
-	.pwrsts_logic_ret = PWRSTS_RET,
 	.banks		  = 5,
-	.pwrsts_mem_ret	= {
-		[0] = PWRSTS_OFF_RET,	/* core_nret_bank */
-		[1] = PWRSTS_OFF_RET,	/* core_ocmram */
-		[2] = PWRSTS_OFF_RET,	/* core_other_bank */
-		[3] = PWRSTS_OFF_RET,	/* ipu_l2ram */
-		[4] = PWRSTS_OFF_RET,	/* ipu_unicache */
-	},
 	.pwrsts_mem_on	= {
 		[0] = PWRSTS_ON,	/* core_nret_bank */
 		[1] = PWRSTS_ON,	/* core_ocmram */
@@ -226,11 +192,7 @@ static struct powerdomain vpe_7xx_pwrdm = {
 	.prcm_offs	  = DRA7XX_PRM_VPE_INST,
 	.prcm_partition	  = DRA7XX_PRM_PARTITION,
 	.pwrsts		  = PWRSTS_OFF_ON,
-	.pwrsts_logic_ret = PWRSTS_OFF,
 	.banks		  = 1,
-	.pwrsts_mem_ret	= {
-		[0] = PWRSTS_OFF_RET,	/* vpe_bank */
-	},
 	.pwrsts_mem_on	= {
 		[0] = PWRSTS_ON,	/* vpe_bank */
 	},
@@ -260,14 +222,8 @@ static struct powerdomain l3init_7xx_pwrdm = {
 	.name		  = "l3init_pwrdm",
 	.prcm_offs	  = DRA7XX_PRM_L3INIT_INST,
 	.prcm_partition	  = DRA7XX_PRM_PARTITION,
-	.pwrsts		  = PWRSTS_RET_ON,
-	.pwrsts_logic_ret = PWRSTS_RET,
+	.pwrsts		  = PWRSTS_ON,
 	.banks		  = 3,
-	.pwrsts_mem_ret	= {
-		[0] = PWRSTS_OFF_RET,	/* gmac_bank */
-		[1] = PWRSTS_OFF_RET,	/* l3init_bank1 */
-		[2] = PWRSTS_OFF_RET,	/* l3init_bank2 */
-	},
 	.pwrsts_mem_on	= {
 		[0] = PWRSTS_ON,	/* gmac_bank */
 		[1] = PWRSTS_ON,	/* l3init_bank1 */
@@ -283,9 +239,6 @@ static struct powerdomain eve3_7xx_pwrdm = {
 	.prcm_partition	  = DRA7XX_PRM_PARTITION,
 	.pwrsts		  = PWRSTS_OFF_ON,
 	.banks		  = 1,
-	.pwrsts_mem_ret	= {
-		[0] = PWRSTS_OFF_RET,	/* eve3_bank */
-	},
 	.pwrsts_mem_on	= {
 		[0] = PWRSTS_ON,	/* eve3_bank */
 	},
@@ -299,9 +252,6 @@ static struct powerdomain emu_7xx_pwrdm = {
 	.prcm_partition	  = DRA7XX_PRM_PARTITION,
 	.pwrsts		  = PWRSTS_OFF_ON,
 	.banks		  = 1,
-	.pwrsts_mem_ret	= {
-		[0] = PWRSTS_OFF_RET,	/* emu_bank */
-	},
 	.pwrsts_mem_on	= {
 		[0] = PWRSTS_ON,	/* emu_bank */
 	},
@@ -314,11 +264,6 @@ static struct powerdomain dsp2_7xx_pwrdm = {
 	.prcm_partition	  = DRA7XX_PRM_PARTITION,
 	.pwrsts		  = PWRSTS_OFF_ON,
 	.banks		  = 3,
-	.pwrsts_mem_ret	= {
-		[0] = PWRSTS_OFF_RET,	/* dsp2_edma */
-		[1] = PWRSTS_OFF_RET,	/* dsp2_l1 */
-		[2] = PWRSTS_OFF_RET,	/* dsp2_l2 */
-	},
 	.pwrsts_mem_on	= {
 		[0] = PWRSTS_ON,	/* dsp2_edma */
 		[1] = PWRSTS_ON,	/* dsp2_l1 */
@@ -334,11 +279,6 @@ static struct powerdomain dsp1_7xx_pwrdm = {
 	.prcm_partition	  = DRA7XX_PRM_PARTITION,
 	.pwrsts		  = PWRSTS_OFF_ON,
 	.banks		  = 3,
-	.pwrsts_mem_ret	= {
-		[0] = PWRSTS_OFF_RET,	/* dsp1_edma */
-		[1] = PWRSTS_OFF_RET,	/* dsp1_l1 */
-		[2] = PWRSTS_OFF_RET,	/* dsp1_l2 */
-	},
 	.pwrsts_mem_on	= {
 		[0] = PWRSTS_ON,	/* dsp1_edma */
 		[1] = PWRSTS_ON,	/* dsp1_l1 */
@@ -354,9 +294,6 @@ static struct powerdomain cam_7xx_pwrdm = {
 	.prcm_partition	  = DRA7XX_PRM_PARTITION,
 	.pwrsts		  = PWRSTS_OFF_ON,
 	.banks		  = 1,
-	.pwrsts_mem_ret	= {
-		[0] = PWRSTS_OFF_RET,	/* vip_bank */
-	},
 	.pwrsts_mem_on	= {
 		[0] = PWRSTS_ON,	/* vip_bank */
 	},
@@ -370,9 +307,6 @@ static struct powerdomain eve4_7xx_pwrdm = {
 	.prcm_partition	  = DRA7XX_PRM_PARTITION,
 	.pwrsts		  = PWRSTS_OFF_ON,
 	.banks		  = 1,
-	.pwrsts_mem_ret	= {
-		[0] = PWRSTS_OFF_RET,	/* eve4_bank */
-	},
 	.pwrsts_mem_on	= {
 		[0] = PWRSTS_ON,	/* eve4_bank */
 	},
@@ -386,9 +320,6 @@ static struct powerdomain eve2_7xx_pwrdm = {
 	.prcm_partition	  = DRA7XX_PRM_PARTITION,
 	.pwrsts		  = PWRSTS_OFF_ON,
 	.banks		  = 1,
-	.pwrsts_mem_ret	= {
-		[0] = PWRSTS_OFF_RET,	/* eve2_bank */
-	},
 	.pwrsts_mem_on	= {
 		[0] = PWRSTS_ON,	/* eve2_bank */
 	},
@@ -402,9 +333,6 @@ static struct powerdomain eve1_7xx_pwrdm = {
 	.prcm_partition	  = DRA7XX_PRM_PARTITION,
 	.pwrsts		  = PWRSTS_OFF_ON,
 	.banks		  = 1,
-	.pwrsts_mem_ret	= {
-		[0] = PWRSTS_OFF_RET,	/* eve1_bank */
-	},
 	.pwrsts_mem_on	= {
 		[0] = PWRSTS_ON,	/* eve1_bank */
 	},

arch/arm/mach-omap2/timer.c

@@ -496,7 +496,6 @@ void __init omap_init_time(void)
 	__omap_sync32k_timer_init(1, "timer_32k_ck", "ti,timer-alwon",
 			2, "timer_sys_ck", NULL, false);
 
-	if (of_have_populated_dt())
 	clocksource_probe();
 }
 
@@ -505,6 +504,8 @@ void __init omap3_secure_sync32k_timer_init(void)
 {
 	__omap_sync32k_timer_init(12, "secure_32k_fck", "ti,timer-secure",
 			2, "timer_sys_ck", NULL, false);
+
+	clocksource_probe();
 }
 #endif /* CONFIG_ARCH_OMAP3 */
 
@@ -513,6 +514,8 @@ void __init omap3_gptimer_timer_init(void)
 {
 	__omap_sync32k_timer_init(2, "timer_sys_ck", NULL,
 			1, "timer_sys_ck", "ti,timer-alwon", true);
+
+	clocksource_probe();
 }
 #endif
 

arch/arm/plat-samsung/devs.c

@@ -68,7 +68,7 @@
 #include <linux/platform_data/asoc-s3c.h>
 #include <linux/platform_data/spi-s3c64xx.h>
 
-static u64 samsung_device_dma_mask = DMA_BIT_MASK(32);
+#define samsung_device_dma_mask (*((u64[]) { DMA_BIT_MASK(32) }))
 
 /* AC97 */
 #ifdef CONFIG_CPU_S3C2440

arch/arm64/boot/dts/lg/lg1312.dtsi

@@ -125,7 +125,7 @@ amba {
 		#size-cells = <1>;
 		#interrupts-cells = <3>;
 
-		compatible = "arm,amba-bus";
+		compatible = "simple-bus";
 		interrupt-parent = <&gic>;
 		ranges;
 

arch/arm64/boot/dts/rockchip/rk3399.dtsi

@@ -163,7 +163,7 @@ xin24m: xin24m {
 	};
 
 	amba {
-		compatible = "arm,amba-bus";
+		compatible = "simple-bus";
 		#address-cells = <2>;
 		#size-cells = <2>;
 		ranges;

drivers/memory/omap-gpmc.c

@@ -398,7 +398,7 @@ static void gpmc_cs_bool_timings(int cs, const struct gpmc_bool_timings *p)
 	gpmc_cs_modify_reg(cs, GPMC_CS_CONFIG4,
 			   GPMC_CONFIG4_OEEXTRADELAY, p->oe_extra_delay);
 	gpmc_cs_modify_reg(cs, GPMC_CS_CONFIG4,
-			   GPMC_CONFIG4_OEEXTRADELAY, p->we_extra_delay);
+			   GPMC_CONFIG4_WEEXTRADELAY, p->we_extra_delay);
 	gpmc_cs_modify_reg(cs, GPMC_CS_CONFIG6,
 			   GPMC_CONFIG6_CYCLE2CYCLESAMECSEN,
 			   p->cycle2cyclesamecsen);