ARM: dts: qcom: mdm9615: fix PMIC node labels

Change PM8018 node labels to start with pm8018_ prefix, following other
Qualcomm PMIC device nodes.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230928110309.1212221-10-dmitry.baryshkov@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi

@@ -76,7 +76,7 @@ reset-out-pins {
 	};
 };
 
-&pmicgpio {
+&pm8018_gpio {
 	usb_vbus_5v_pins: usb-vbus-5v-state {
 		pins = "gpio4";
 		function = "normal";

arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi

@@ -261,7 +261,7 @@ qcom,ssbi@500000 {
 			reg = <0x500000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
 
-			pmicintc: pmic {
+			pm8018: pmic {
 				compatible = "qcom,pm8018", "qcom,pm8921";
 				interrupts = <GIC_PPI 226 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <2>;
@@ -272,38 +272,38 @@ pmicintc: pmic {
 				pwrkey@1c {
 					compatible = "qcom,pm8018-pwrkey", "qcom,pm8921-pwrkey";
 					reg = <0x1c>;
-					interrupt-parent = <&pmicintc>;
+					interrupt-parent = <&pm8018>;
 					interrupts = <50 IRQ_TYPE_EDGE_RISING>,
 						     <51 IRQ_TYPE_EDGE_RISING>;
 					debounce = <15625>;
 					pull-up;
 				};
 
-				pmicmpp: mpps@50 {
+				pm8018_mpps: mpps@50 {
 					compatible = "qcom,pm8018-mpp", "qcom,ssbi-mpp";
 					interrupt-controller;
 					#interrupt-cells = <2>;
 					reg = <0x50>;
 					gpio-controller;
 					#gpio-cells = <2>;
-					gpio-ranges = <&pmicmpp 0 0 6>;
+					gpio-ranges = <&pm8018_mpps 0 0 6>;
 				};
 
 				rtc@11d {
 					compatible = "qcom,pm8018-rtc", "qcom,pm8921-rtc";
-					interrupt-parent = <&pmicintc>;
+					interrupt-parent = <&pm8018>;
 					interrupts = <39 IRQ_TYPE_EDGE_RISING>;
 					reg = <0x11d>;
 					allow-set-time;
 				};
 
-				pmicgpio: gpio@150 {
+				pm8018_gpio: gpio@150 {
 					compatible = "qcom,pm8018-gpio", "qcom,ssbi-gpio";
 					reg = <0x150>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
 					gpio-controller;
-					gpio-ranges = <&pmicgpio 0 0 6>;
+					gpio-ranges = <&pm8018_gpio 0 0 6>;
 					#gpio-cells = <2>;
 				};
 			};