arm64: dts: renesas: rzg3s-smarc-som: Use switches' names to select on-board functionalities

The intention of the SW_SD0_DEV_SEL and SW_SD2_EN macros was to reflect the
state of the SW_CONFIG individual switches available on the RZ/G3S Smarc
Module, and at the same time to have a descriptive name for the switches
themselves.  Each individual switch is associated with a signal name,
which might be active-low or not on the board.  Using signal names
instead of SW_CONFIG switch names may be confusing for a user who just
playes with switches to select individual functionalities, but also for
an advanced user who looks at the schematics.  To avoid even further
confusion, use the switches' names here and instantiate them with an
ON/OFF state.  This should be simpler, even though the name of the
switches is not that intuitive.  The switches' names documentation
reflects the switches' purposes.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231207070700.4156557-11-claudiu.beznea.uj@bp.renesas.comSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

arch/arm64/boot/dts/renesas/rzg3s-smarc-som.dtsi

@@ -9,23 +9,31 @@
 #include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
 
 /*
- * Signals of SW_CONFIG switches:
- * @SW_SD0_DEV_SEL:
- *	0 - SD0 is connected to eMMC
- *	1 - SD0 is connected to uSD0 card
- * @SW_SD2_EN:
- *	0 - SCIF1, SSI0, IRQ0, IRQ1 connected to SoC
- *	1 - SD2 is connected to SoC
+ * On-board switches' states:
+ * @SW_OFF: switch's state is OFF
+ * @SW_ON:  switch's state is ON
  */
-#define SW_SD0_DEV_SEL	1
-#define SW_SD2_EN	1
+#define SW_OFF		0
+#define SW_ON		1
+
+/*
+ * SW_CONFIG[x] switches' states:
+ * @SW_CONFIG2:
+ *	SW_OFF - SD0 is connected to eMMC
+ *	SW_ON  - SD0 is connected to uSD0 card
+ * @SW_CONFIG3:
+ *	SW_OFF - SD2 is connected to SoC
+ *	SW_ON  - SCIF1, SSI0, IRQ0, IRQ1 connected to SoC
+ */
+#define SW_CONFIG2	SW_ON
+#define SW_CONFIG3	SW_OFF
 
 / {
 	compatible = "renesas,rzg3s-smarcm", "renesas,r9a08g045s33", "renesas,r9a08g045";
 
 	aliases {
 		mmc0 = &sdhi0;
-#if SW_SD2_EN
+#if SW_CONFIG3 == SW_OFF
 		mmc2 = &sdhi2;
 #endif
 	};
@@ -50,7 +58,7 @@ vcc_sdhi0: regulator0 {
 		enable-active-high;
 	};
 
-#if SW_SD0_DEV_SEL
+#if SW_CONFIG2 == SW_ON
 	vccq_sdhi0: regulator1 {
 		compatible = "regulator-gpio";
 		regulator-name = "SDHI0 VccQ";
@@ -85,7 +93,7 @@ &extal_clk {
 	clock-frequency = <24000000>;
 };
 
-#if SW_SD0_DEV_SEL
+#if SW_CONFIG2 == SW_ON
 /* SD0 slot */
 &sdhi0 {
 	pinctrl-0 = <&sdhi0_pins>;
@@ -116,7 +124,7 @@ &sdhi0 {
 };
 #endif
 
-#if SW_SD2_EN
+#if SW_CONFIG3 == SW_OFF
 &sdhi2 {
 	pinctrl-0 = <&sdhi2_pins>;
 	pinctrl-names = "default";