powerpc: Merge the RELOCATABLE config entries for ppc32 and ppc64

It makes no sense to keep two separate RELOCATABLE config entries for
ppc32 and ppc64 respectively. Merge them into one and move it to a
common place.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

arch/powerpc/Kconfig

@@ -458,6 +458,33 @@ config KEXEC
 	  interface is strongly in flux, so no good recommendation can be
 	  made.
 
+config RELOCATABLE
+	bool "Build a relocatable kernel"
+	depends on (PPC64 && !COMPILE_TEST) || (FLATMEM && (44x || FSL_BOOKE))
+	select NONSTATIC_KERNEL
+	help
+	  This builds a kernel image that is capable of running at the
+	  location the kernel is loaded at. For ppc32, there is no any
+	  alignment restrictions, and this feature is a superset of
+	  DYNAMIC_MEMSTART and hence overrides it. For ppc64, we should use
+	  16k-aligned base address. The kernel is linked as a
+	  position-independent executable (PIE) and contains dynamic relocations
+	  which are processed early in the bootup process.
+
+	  One use is for the kexec on panic case where the recovery kernel
+	  must live at a different physical address than the primary
+	  kernel.
+
+	  Note: If CONFIG_RELOCATABLE=y, then the kernel runs from the address
+	  it has been loaded at and the compile time physical addresses
+	  CONFIG_PHYSICAL_START is ignored.  However CONFIG_PHYSICAL_START
+	  setting can still be useful to bootwrappers that need to know the
+	  load address of the kernel (eg. u-boot/mkimage).
+
+config RELOCATABLE_PPC32
+	def_bool y
+	depends on PPC32 && RELOCATABLE
+
 config CRASH_DUMP
 	bool "Build a kdump crash kernel"
 	depends on PPC64 || 6xx || FSL_BOOKE || (44x && !SMP)
@@ -950,29 +977,6 @@ config DYNAMIC_MEMSTART
 
 	  This option is overridden by CONFIG_RELOCATABLE
 
-config RELOCATABLE
-	bool "Build a relocatable kernel"
-	depends on FLATMEM && (44x || FSL_BOOKE)
-	select NONSTATIC_KERNEL
-	help
-	  This builds a kernel image that is capable of running at the
-	  location the kernel is loaded at, without any alignment restrictions.
-	  This feature is a superset of DYNAMIC_MEMSTART and hence overrides it.
-
-	  One use is for the kexec on panic case where the recovery kernel
-	  must live at a different physical address than the primary
-	  kernel.
-
-	  Note: If CONFIG_RELOCATABLE=y, then the kernel runs from the address
-	  it has been loaded at and the compile time physical addresses
-	  CONFIG_PHYSICAL_START is ignored.  However CONFIG_PHYSICAL_START
-	  setting can still be useful to bootwrappers that need to know the
-	  load address of the kernel (eg. u-boot/mkimage).
-
-config RELOCATABLE_PPC32
-	def_bool y
-	depends on PPC32 && RELOCATABLE
-
 config PAGE_OFFSET_BOOL
 	bool "Set custom page offset address"
 	depends on ADVANCED_OPTIONS
@@ -1058,21 +1062,6 @@ config PIN_TLB
 endmenu
 
 if PPC64
-config RELOCATABLE
-	bool "Build a relocatable kernel"
-	depends on !COMPILE_TEST
-	select NONSTATIC_KERNEL
-	help
-	  This builds a kernel image that is capable of running anywhere
-	  in the RMA (real memory area) at any 16k-aligned base address.
-	  The kernel is linked as a position-independent executable (PIE)
-	  and contains dynamic relocations which are processed early
-	  in the bootup process.
-
-	  One use is for the kexec on panic case where the recovery kernel
-	  must live at a different physical address than the primary
-	  kernel.
-
 # This value must have zeroes in the bottom 60 bits otherwise lots will break
 config PAGE_OFFSET
 	hex