mfd: stpmic1: Add STPMIC1 driver

STPMIC1 is a PMIC from STMicroelectronics. The STPMIC1 integrates 10
regulators, 3 power switches, a watchdog and an input for a power on key.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

drivers/mfd/Kconfig

@@ -1871,6 +1871,22 @@ config MFD_STM32_TIMERS
 	  for PWM and IIO Timer. This driver allow to share the
 	  registers between the others drivers.
 
+config MFD_STPMIC1
+	tristate "Support for STPMIC1 PMIC"
+	depends on (I2C=y && OF)
+	select REGMAP_I2C
+	select REGMAP_IRQ
+	select MFD_CORE
+	help
+	  Support for ST Microelectronics STPMIC1 PMIC. STPMIC1 has power on
+	  key, watchdog and regulator functionalities which are supported via
+	  the relevant subsystems. This driver provides core support for the
+	  STPMIC1. In order to use the actual functionaltiy of the device other
+	  drivers must be enabled.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called stpmic1.
+
 menu "Multimedia Capabilities Port drivers"
 	depends on ARCH_SA1100
 

drivers/mfd/Makefile

@@ -233,6 +233,7 @@ obj-$(CONFIG_INTEL_SOC_PMIC_CHTDC_TI)	+= intel_soc_pmic_chtdc_ti.o
 obj-$(CONFIG_MFD_MT6397)	+= mt6397-core.o
 
 obj-$(CONFIG_MFD_ALTERA_A10SR)	+= altera-a10sr.o
+obj-$(CONFIG_MFD_STPMIC1)	+= stpmic1.o
 obj-$(CONFIG_MFD_SUN4I_GPADC)	+= sun4i-gpadc.o
 
 obj-$(CONFIG_MFD_STM32_LPTIMER)	+= stm32-lptimer.o

drivers/mfd/stpmic1.c

+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) STMicroelectronics 2018
+// Author: Pascal Paillet <p.paillet@st.com>
+
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/stpmic1.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/pm_wakeirq.h>
+#include <linux/regmap.h>
+
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+#define STPMIC1_MAIN_IRQ 0
+
+static const struct regmap_range stpmic1_readable_ranges[] = {
+	regmap_reg_range(TURN_ON_SR, VERSION_SR),
+	regmap_reg_range(SWOFF_PWRCTRL_CR, LDO6_STDBY_CR),
+	regmap_reg_range(BST_SW_CR, BST_SW_CR),
+	regmap_reg_range(INT_PENDING_R1, INT_PENDING_R4),
+	regmap_reg_range(INT_CLEAR_R1, INT_CLEAR_R4),
+	regmap_reg_range(INT_MASK_R1, INT_MASK_R4),
+	regmap_reg_range(INT_SET_MASK_R1, INT_SET_MASK_R4),
+	regmap_reg_range(INT_CLEAR_MASK_R1, INT_CLEAR_MASK_R4),
+	regmap_reg_range(INT_SRC_R1, INT_SRC_R1),
+};
+
+static const struct regmap_range stpmic1_writeable_ranges[] = {
+	regmap_reg_range(SWOFF_PWRCTRL_CR, LDO6_STDBY_CR),
+	regmap_reg_range(BST_SW_CR, BST_SW_CR),
+	regmap_reg_range(INT_CLEAR_R1, INT_CLEAR_R4),
+	regmap_reg_range(INT_SET_MASK_R1, INT_SET_MASK_R4),
+	regmap_reg_range(INT_CLEAR_MASK_R1, INT_CLEAR_MASK_R4),
+};
+
+static const struct regmap_range stpmic1_volatile_ranges[] = {
+	regmap_reg_range(TURN_ON_SR, VERSION_SR),
+	regmap_reg_range(WCHDG_CR, WCHDG_CR),
+	regmap_reg_range(INT_PENDING_R1, INT_PENDING_R4),
+	regmap_reg_range(INT_SRC_R1, INT_SRC_R4),
+};
+
+static const struct regmap_access_table stpmic1_readable_table = {
+	.yes_ranges = stpmic1_readable_ranges,
+	.n_yes_ranges = ARRAY_SIZE(stpmic1_readable_ranges),
+};
+
+static const struct regmap_access_table stpmic1_writeable_table = {
+	.yes_ranges = stpmic1_writeable_ranges,
+	.n_yes_ranges = ARRAY_SIZE(stpmic1_writeable_ranges),
+};
+
+static const struct regmap_access_table stpmic1_volatile_table = {
+	.yes_ranges = stpmic1_volatile_ranges,
+	.n_yes_ranges = ARRAY_SIZE(stpmic1_volatile_ranges),
+};
+
+const struct regmap_config stpmic1_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.cache_type = REGCACHE_RBTREE,
+	.max_register = PMIC_MAX_REGISTER_ADDRESS,
+	.rd_table = &stpmic1_readable_table,
+	.wr_table = &stpmic1_writeable_table,
+	.volatile_table = &stpmic1_volatile_table,
+};
+
+static const struct regmap_irq stpmic1_irqs[] = {
+	REGMAP_IRQ_REG(IT_PONKEY_F, 0, 0x01),
+	REGMAP_IRQ_REG(IT_PONKEY_R, 0, 0x02),
+	REGMAP_IRQ_REG(IT_WAKEUP_F, 0, 0x04),
+	REGMAP_IRQ_REG(IT_WAKEUP_R, 0, 0x08),
+	REGMAP_IRQ_REG(IT_VBUS_OTG_F, 0, 0x10),
+	REGMAP_IRQ_REG(IT_VBUS_OTG_R, 0, 0x20),
+	REGMAP_IRQ_REG(IT_SWOUT_F, 0, 0x40),
+	REGMAP_IRQ_REG(IT_SWOUT_R, 0, 0x80),
+
+	REGMAP_IRQ_REG(IT_CURLIM_BUCK1, 1, 0x01),
+	REGMAP_IRQ_REG(IT_CURLIM_BUCK2, 1, 0x02),
+	REGMAP_IRQ_REG(IT_CURLIM_BUCK3, 1, 0x04),
+	REGMAP_IRQ_REG(IT_CURLIM_BUCK4, 1, 0x08),
+	REGMAP_IRQ_REG(IT_OCP_OTG, 1, 0x10),
+	REGMAP_IRQ_REG(IT_OCP_SWOUT, 1, 0x20),
+	REGMAP_IRQ_REG(IT_OCP_BOOST, 1, 0x40),
+	REGMAP_IRQ_REG(IT_OVP_BOOST, 1, 0x80),
+
+	REGMAP_IRQ_REG(IT_CURLIM_LDO1, 2, 0x01),
+	REGMAP_IRQ_REG(IT_CURLIM_LDO2, 2, 0x02),
+	REGMAP_IRQ_REG(IT_CURLIM_LDO3, 2, 0x04),
+	REGMAP_IRQ_REG(IT_CURLIM_LDO4, 2, 0x08),
+	REGMAP_IRQ_REG(IT_CURLIM_LDO5, 2, 0x10),
+	REGMAP_IRQ_REG(IT_CURLIM_LDO6, 2, 0x20),
+	REGMAP_IRQ_REG(IT_SHORT_SWOTG, 2, 0x40),
+	REGMAP_IRQ_REG(IT_SHORT_SWOUT, 2, 0x80),
+
+	REGMAP_IRQ_REG(IT_TWARN_F, 3, 0x01),
+	REGMAP_IRQ_REG(IT_TWARN_R, 3, 0x02),
+	REGMAP_IRQ_REG(IT_VINLOW_F, 3, 0x04),
+	REGMAP_IRQ_REG(IT_VINLOW_R, 3, 0x08),
+	REGMAP_IRQ_REG(IT_SWIN_F, 3, 0x40),
+	REGMAP_IRQ_REG(IT_SWIN_R, 3, 0x80),
+};
+
+static const struct regmap_irq_chip stpmic1_regmap_irq_chip = {
+	.name = "pmic_irq",
+	.status_base = INT_PENDING_R1,
+	.mask_base = INT_CLEAR_MASK_R1,
+	.unmask_base = INT_SET_MASK_R1,
+	.ack_base = INT_CLEAR_R1,
+	.num_regs = STPMIC1_PMIC_NUM_IRQ_REGS,
+	.irqs = stpmic1_irqs,
+	.num_irqs = ARRAY_SIZE(stpmic1_irqs),
+};
+
+static int stpmic1_probe(struct i2c_client *i2c,
+			 const struct i2c_device_id *id)
+{
+	struct stpmic1 *ddata;
+	struct device *dev = &i2c->dev;
+	int ret;
+	struct device_node *np = dev->of_node;
+	u32 reg;
+
+	ddata = devm_kzalloc(dev, sizeof(struct stpmic1), GFP_KERNEL);
+	if (!ddata)
+		return -ENOMEM;
+
+	i2c_set_clientdata(i2c, ddata);
+	ddata->dev = dev;
+
+	ddata->regmap = devm_regmap_init_i2c(i2c, &stpmic1_regmap_config);
+	if (IS_ERR(ddata->regmap))
+		return PTR_ERR(ddata->regmap);
+
+	ddata->irq = of_irq_get(np, STPMIC1_MAIN_IRQ);
+	if (ddata->irq < 0) {
+		dev_err(dev, "Failed to get main IRQ: %d\n", ddata->irq);
+		return ddata->irq;
+	}
+
+	ret = regmap_read(ddata->regmap, VERSION_SR, &reg);
+	if (ret) {
+		dev_err(dev, "Unable to read PMIC version\n");
+		return ret;
+	}
+	dev_info(dev, "PMIC Chip Version: 0x%x\n", reg);
+
+	/* Initialize PMIC IRQ Chip & associated IRQ domains */
+	ret = devm_regmap_add_irq_chip(dev, ddata->regmap, ddata->irq,
+				       IRQF_ONESHOT | IRQF_SHARED,
+				       0, &stpmic1_regmap_irq_chip,
+				       &ddata->irq_data);
+	if (ret) {
+		dev_err(dev, "IRQ Chip registration failed: %d\n", ret);
+		return ret;
+	}
+
+	return devm_of_platform_populate(dev);
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int stpmic1_suspend(struct device *dev)
+{
+	struct i2c_client *i2c = to_i2c_client(dev);
+	struct stpmic1 *pmic_dev = i2c_get_clientdata(i2c);
+
+	disable_irq(pmic_dev->irq);
+
+	return 0;
+}
+
+static int stpmic1_resume(struct device *dev)
+{
+	struct i2c_client *i2c = to_i2c_client(dev);
+	struct stpmic1 *pmic_dev = i2c_get_clientdata(i2c);
+	int ret;
+
+	ret = regcache_sync(pmic_dev->regmap);
+	if (ret)
+		return ret;
+
+	enable_irq(pmic_dev->irq);
+
+	return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(stpmic1_pm, stpmic1_suspend, stpmic1_resume);
+
+static const struct of_device_id stpmic1_of_match[] = {
+	{ .compatible = "st,stpmic1", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, stpmic1_of_match);
+
+static struct i2c_driver stpmic1_driver = {
+	.driver = {
+		.name = "stpmic1",
+		.of_match_table = of_match_ptr(stpmic1_of_match),
+		.pm = &stpmic1_pm,
+	},
+	.probe = stpmic1_probe,
+};
+
+module_i2c_driver(stpmic1_driver);
+
+MODULE_DESCRIPTION("STPMIC1 PMIC Driver");
+MODULE_AUTHOR("Pascal Paillet <p.paillet@st.com>");
+MODULE_LICENSE("GPL v2");

include/linux/mfd/stpmic1.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) STMicroelectronics 2018 - All Rights Reserved
+ * Author: Philippe Peurichard <philippe.peurichard@st.com>,
+ * Pascal Paillet <p.paillet@st.com> for STMicroelectronics.
+ */
+
+#ifndef __LINUX_MFD_STPMIC1_H
+#define __LINUX_MFD_STPMIC1_H
+
+#define TURN_ON_SR		0x1
+#define TURN_OFF_SR		0x2
+#define ICC_LDO_TURN_OFF_SR	0x3
+#define ICC_BUCK_TURN_OFF_SR	0x4
+#define RREQ_STATE_SR		0x5
+#define VERSION_SR		0x6
+
+#define SWOFF_PWRCTRL_CR	0x10
+#define PADS_PULL_CR		0x11
+#define BUCKS_PD_CR		0x12
+#define LDO14_PD_CR		0x13
+#define LDO56_VREF_PD_CR	0x14
+#define VBUS_DET_VIN_CR		0x15
+#define PKEY_TURNOFF_CR		0x16
+#define BUCKS_MASK_RANK_CR	0x17
+#define BUCKS_MASK_RESET_CR	0x18
+#define LDOS_MASK_RANK_CR	0x19
+#define LDOS_MASK_RESET_CR	0x1A
+#define WCHDG_CR		0x1B
+#define WCHDG_TIMER_CR		0x1C
+#define BUCKS_ICCTO_CR		0x1D
+#define LDOS_ICCTO_CR		0x1E
+
+#define BUCK1_ACTIVE_CR		0x20
+#define BUCK2_ACTIVE_CR		0x21
+#define BUCK3_ACTIVE_CR		0x22
+#define BUCK4_ACTIVE_CR		0x23
+#define VREF_DDR_ACTIVE_CR	0x24
+#define LDO1_ACTIVE_CR		0x25
+#define LDO2_ACTIVE_CR		0x26
+#define LDO3_ACTIVE_CR		0x27
+#define LDO4_ACTIVE_CR		0x28
+#define LDO5_ACTIVE_CR		0x29
+#define LDO6_ACTIVE_CR		0x2A
+
+#define BUCK1_STDBY_CR		0x30
+#define BUCK2_STDBY_CR		0x31
+#define BUCK3_STDBY_CR		0x32
+#define BUCK4_STDBY_CR		0x33
+#define VREF_DDR_STDBY_CR	0x34
+#define LDO1_STDBY_CR		0x35
+#define LDO2_STDBY_CR		0x36
+#define LDO3_STDBY_CR		0x37
+#define LDO4_STDBY_CR		0x38
+#define LDO5_STDBY_CR		0x39
+#define LDO6_STDBY_CR		0x3A
+
+#define BST_SW_CR		0x40
+
+#define INT_PENDING_R1		0x50
+#define INT_PENDING_R2		0x51
+#define INT_PENDING_R3		0x52
+#define INT_PENDING_R4		0x53
+
+#define INT_DBG_LATCH_R1	0x60
+#define INT_DBG_LATCH_R2	0x61
+#define INT_DBG_LATCH_R3	0x62
+#define INT_DBG_LATCH_R4	0x63
+
+#define INT_CLEAR_R1		0x70
+#define INT_CLEAR_R2		0x71
+#define INT_CLEAR_R3		0x72
+#define INT_CLEAR_R4		0x73
+
+#define INT_MASK_R1		0x80
+#define INT_MASK_R2		0x81
+#define INT_MASK_R3		0x82
+#define INT_MASK_R4		0x83
+
+#define INT_SET_MASK_R1		0x90
+#define INT_SET_MASK_R2		0x91
+#define INT_SET_MASK_R3		0x92
+#define INT_SET_MASK_R4		0x93
+
+#define INT_CLEAR_MASK_R1	0xA0
+#define INT_CLEAR_MASK_R2	0xA1
+#define INT_CLEAR_MASK_R3	0xA2
+#define INT_CLEAR_MASK_R4	0xA3
+
+#define INT_SRC_R1		0xB0
+#define INT_SRC_R2		0xB1
+#define INT_SRC_R3		0xB2
+#define INT_SRC_R4		0xB3
+
+#define PMIC_MAX_REGISTER_ADDRESS INT_SRC_R4
+
+#define STPMIC1_PMIC_NUM_IRQ_REGS 4
+
+#define TURN_OFF_SR_ICC_EVENT	0x08
+
+#define LDO_VOLTAGE_MASK		GENMASK(6, 2)
+#define BUCK_VOLTAGE_MASK		GENMASK(7, 2)
+#define LDO_BUCK_VOLTAGE_SHIFT		2
+
+#define LDO_ENABLE_MASK			BIT(0)
+#define BUCK_ENABLE_MASK		BIT(0)
+
+#define BUCK_HPLP_ENABLE_MASK		BIT(1)
+#define BUCK_HPLP_SHIFT			1
+
+#define STDBY_ENABLE_MASK  BIT(0)
+
+#define BUCKS_PD_CR_REG_MASK	GENMASK(7, 0)
+#define BUCK_MASK_RANK_REGISTER_MASK	GENMASK(3, 0)
+#define BUCK_MASK_RESET_REGISTER_MASK	GENMASK(3, 0)
+#define LDO1234_PULL_DOWN_REGISTER_MASK	GENMASK(7, 0)
+#define LDO56_VREF_PD_CR_REG_MASK	GENMASK(5, 0)
+#define LDO_MASK_RANK_REGISTER_MASK	GENMASK(5, 0)
+#define LDO_MASK_RESET_REGISTER_MASK	GENMASK(5, 0)
+
+#define BUCK1_PULL_DOWN_REG		BUCKS_PD_CR
+#define BUCK1_PULL_DOWN_MASK		BIT(0)
+#define BUCK2_PULL_DOWN_REG		BUCKS_PD_CR
+#define BUCK2_PULL_DOWN_MASK		BIT(2)
+#define BUCK3_PULL_DOWN_REG		BUCKS_PD_CR
+#define BUCK3_PULL_DOWN_MASK		BIT(4)
+#define BUCK4_PULL_DOWN_REG		BUCKS_PD_CR
+#define BUCK4_PULL_DOWN_MASK		BIT(6)
+
+#define LDO1_PULL_DOWN_REG		LDO14_PD_CR
+#define LDO1_PULL_DOWN_MASK		BIT(0)
+#define LDO2_PULL_DOWN_REG		LDO14_PD_CR
+#define LDO2_PULL_DOWN_MASK		BIT(2)
+#define LDO3_PULL_DOWN_REG		LDO14_PD_CR
+#define LDO3_PULL_DOWN_MASK		BIT(4)
+#define LDO4_PULL_DOWN_REG		LDO14_PD_CR
+#define LDO4_PULL_DOWN_MASK		BIT(6)
+#define LDO5_PULL_DOWN_REG		LDO56_VREF_PD_CR
+#define LDO5_PULL_DOWN_MASK		BIT(0)
+#define LDO6_PULL_DOWN_REG		LDO56_VREF_PD_CR
+#define LDO6_PULL_DOWN_MASK		BIT(2)
+#define VREF_DDR_PULL_DOWN_REG		LDO56_VREF_PD_CR
+#define VREF_DDR_PULL_DOWN_MASK		BIT(4)
+
+#define BUCKS_ICCTO_CR_REG_MASK	GENMASK(6, 0)
+#define LDOS_ICCTO_CR_REG_MASK	GENMASK(5, 0)
+
+#define LDO_BYPASS_MASK			BIT(7)
+
+/* Main PMIC Control Register
+ * SWOFF_PWRCTRL_CR
+ * Address : 0x10
+ */
+#define ICC_EVENT_ENABLED		BIT(4)
+#define PWRCTRL_POLARITY_HIGH		BIT(3)
+#define PWRCTRL_PIN_VALID		BIT(2)
+#define RESTART_REQUEST_ENABLED		BIT(1)
+#define SOFTWARE_SWITCH_OFF_ENABLED	BIT(0)
+
+/* Main PMIC PADS Control Register
+ * PADS_PULL_CR
+ * Address : 0x11
+ */
+#define WAKEUP_DETECTOR_DISABLED	BIT(4)
+#define PWRCTRL_PD_ACTIVE		BIT(3)
+#define PWRCTRL_PU_ACTIVE		BIT(2)
+#define WAKEUP_PD_ACTIVE		BIT(1)
+#define PONKEY_PU_INACTIVE		BIT(0)
+
+/* Main PMIC VINLOW Control Register
+ * VBUS_DET_VIN_CRC DMSC
+ * Address : 0x15
+ */
+#define SWIN_DETECTOR_ENABLED		BIT(7)
+#define SWOUT_DETECTOR_ENABLED		BIT(6)
+#define VINLOW_ENABLED			BIT(0)
+#define VINLOW_CTRL_REG_MASK		GENMASK(7, 0)
+
+/* USB Control Register
+ * Address : 0x40
+ */
+#define BOOST_OVP_DISABLED		BIT(7)
+#define VBUS_OTG_DETECTION_DISABLED	BIT(6)
+#define SW_OUT_DISCHARGE		BIT(5)
+#define VBUS_OTG_DISCHARGE		BIT(4)
+#define OCP_LIMIT_HIGH			BIT(3)
+#define SWIN_SWOUT_ENABLED		BIT(2)
+#define USBSW_OTG_SWITCH_ENABLED	BIT(1)
+#define BOOST_ENABLED			BIT(0)
+
+/* PKEY_TURNOFF_CR
+ * Address : 0x16
+ */
+#define PONKEY_PWR_OFF			BIT(7)
+#define PONKEY_CC_FLAG_CLEAR		BIT(6)
+#define PONKEY_TURNOFF_TIMER_MASK	GENMASK(3, 0)
+#define PONKEY_TURNOFF_MASK		GENMASK(7, 0)
+
+/*
+ * struct stpmic1 - stpmic1 master device for sub-drivers
+ * @dev: master device of the chip (can be used to access platform data)
+ * @irq: main IRQ number
+ * @regmap_irq_chip_data: irq chip data
+ */
+struct stpmic1 {
+	struct device *dev;
+	struct regmap *regmap;
+	int irq;
+	struct regmap_irq_chip_data *irq_data;
+};
+
+#endif /*  __LINUX_MFD_STPMIC1_H */