Merge branch 'tja1103-driver'

Radu Pirea says:

====================
TJA1103 driver

This small series adds the TJA1103 PHY driver.

Changes in v3:
 - use phy_read_mmd_poll_timeout instead of spin_until_cond
 - changed the phy name from a generic one to something specific
 - minor indentation change

Changes in v2:
 - implemented genphy_c45_pma_suspend/genphy_c45_pma_suspend
 - set default internal delays set to 2ns(90 degrees)
 - added "VEND1_" prefix to the register definitions
 - disable rxid in case of txid
 - disable txid in case of rxid
 - disable internal delays in rgmii mode
 - reduced max line length to 80 characters
 - rebased on top of net-next/master
 - use genphy_c45_loopback as .set_loopback callback
 - renamed the driver from nxp-c45 to nxp-c45-tja11xx
 - used phy phy_set_bits_mmd/phy_clear_bits_mmd instead on phy_write_mmd where
 I had to set/clear one bit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

MAINTAINERS

@@ -12840,6 +12840,12 @@ F:	drivers/nvmem/
 F:	include/linux/nvmem-consumer.h
 F:	include/linux/nvmem-provider.h
 
+NXP C45 TJA11XX PHY DRIVER
+M:	Radu Pirea <radu-nicolae.pirea@oss.nxp.com>
+L:	netdev@vger.kernel.org
+S:	Maintained
+F:	drivers/net/phy/nxp-c45-tja11xx.c
+
 NXP FSPI DRIVER
 M:	Ashish Kumar <ashish.kumar@nxp.com>
 R:	Yogesh Gaur <yogeshgaur.83@gmail.com>

drivers/net/phy/Kconfig

@@ -234,6 +234,12 @@ config NATIONAL_PHY
 	help
 	  Currently supports the DP83865 PHY.
 
+config NXP_C45_TJA11XX_PHY
+	tristate "NXP C45 TJA11XX PHYs"
+	help
+	  Enable support for NXP C45 TJA11XX PHYs.
+	  Currently supports only the TJA1103 PHY.
+
 config NXP_TJA11XX_PHY
 	tristate "NXP TJA11xx PHYs support"
 	depends on HWMON

drivers/net/phy/Makefile

@@ -71,6 +71,7 @@ obj-$(CONFIG_MICROCHIP_PHY)	+= microchip.o
 obj-$(CONFIG_MICROCHIP_T1_PHY)	+= microchip_t1.o
 obj-$(CONFIG_MICROSEMI_PHY)	+= mscc/
 obj-$(CONFIG_NATIONAL_PHY)	+= national.o
+obj-$(CONFIG_NXP_C45_TJA11XX_PHY)	+= nxp-c45-tja11xx.o
 obj-$(CONFIG_NXP_TJA11XX_PHY)	+= nxp-tja11xx.o
 obj-$(CONFIG_QSEMI_PHY)		+= qsemi.o
 obj-$(CONFIG_REALTEK_PHY)	+= realtek.o

drivers/net/phy/nxp-c45-tja11xx.c

+// SPDX-License-Identifier: GPL-2.0
+/* NXP C45 PHY driver
+ * Copyright (C) 2021 NXP
+ * Author: Radu Pirea <radu-nicolae.pirea@oss.nxp.com>
+ */
+
+#include <linux/delay.h>
+#include <linux/ethtool.h>
+#include <linux/ethtool_netlink.h>
+#include <linux/kernel.h>
+#include <linux/mii.h>
+#include <linux/module.h>
+#include <linux/phy.h>
+#include <linux/processor.h>
+#include <linux/property.h>
+
+#define PHY_ID_TJA_1103			0x001BB010
+
+#define PMAPMD_B100T1_PMAPMD_CTL	0x0834
+#define B100T1_PMAPMD_CONFIG_EN		BIT(15)
+#define B100T1_PMAPMD_MASTER		BIT(14)
+#define MASTER_MODE			(B100T1_PMAPMD_CONFIG_EN | \
+					 B100T1_PMAPMD_MASTER)
+#define SLAVE_MODE			(B100T1_PMAPMD_CONFIG_EN)
+
+#define VEND1_DEVICE_CONTROL		0x0040
+#define DEVICE_CONTROL_RESET		BIT(15)
+#define DEVICE_CONTROL_CONFIG_GLOBAL_EN	BIT(14)
+#define DEVICE_CONTROL_CONFIG_ALL_EN	BIT(13)
+
+#define VEND1_PHY_CONTROL		0x8100
+#define PHY_CONFIG_EN			BIT(14)
+#define PHY_START_OP			BIT(0)
+
+#define VEND1_PHY_CONFIG		0x8108
+#define PHY_CONFIG_AUTO			BIT(0)
+
+#define VEND1_SIGNAL_QUALITY		0x8320
+#define SQI_VALID			BIT(14)
+#define SQI_MASK			GENMASK(2, 0)
+#define MAX_SQI				SQI_MASK
+
+#define VEND1_CABLE_TEST		0x8330
+#define CABLE_TEST_ENABLE		BIT(15)
+#define CABLE_TEST_START		BIT(14)
+#define CABLE_TEST_VALID		BIT(13)
+#define CABLE_TEST_OK			0x00
+#define CABLE_TEST_SHORTED		0x01
+#define CABLE_TEST_OPEN			0x02
+#define CABLE_TEST_UNKNOWN		0x07
+
+#define VEND1_PORT_CONTROL		0x8040
+#define PORT_CONTROL_EN			BIT(14)
+
+#define VEND1_PORT_INFRA_CONTROL	0xAC00
+#define PORT_INFRA_CONTROL_EN		BIT(14)
+
+#define VEND1_RXID			0xAFCC
+#define VEND1_TXID			0xAFCD
+#define ID_ENABLE			BIT(15)
+
+#define VEND1_ABILITIES			0xAFC4
+#define RGMII_ID_ABILITY		BIT(15)
+#define RGMII_ABILITY			BIT(14)
+#define RMII_ABILITY			BIT(10)
+#define REVMII_ABILITY			BIT(9)
+#define MII_ABILITY			BIT(8)
+#define SGMII_ABILITY			BIT(0)
+
+#define VEND1_MII_BASIC_CONFIG		0xAFC6
+#define MII_BASIC_CONFIG_REV		BIT(8)
+#define MII_BASIC_CONFIG_SGMII		0x9
+#define MII_BASIC_CONFIG_RGMII		0x7
+#define MII_BASIC_CONFIG_RMII		0x5
+#define MII_BASIC_CONFIG_MII		0x4
+
+#define VEND1_SYMBOL_ERROR_COUNTER	0x8350
+#define VEND1_LINK_DROP_COUNTER		0x8352
+#define VEND1_LINK_LOSSES_AND_FAILURES	0x8353
+#define VEND1_R_GOOD_FRAME_CNT		0xA950
+#define VEND1_R_BAD_FRAME_CNT		0xA952
+#define VEND1_R_RXER_FRAME_CNT		0xA954
+#define VEND1_RX_PREAMBLE_COUNT		0xAFCE
+#define VEND1_TX_PREAMBLE_COUNT		0xAFCF
+#define VEND1_RX_IPG_LENGTH		0xAFD0
+#define VEND1_TX_IPG_LENGTH		0xAFD1
+#define COUNTER_EN			BIT(15)
+
+#define RGMII_PERIOD_PS			8000U
+#define PS_PER_DEGREE			div_u64(RGMII_PERIOD_PS, 360)
+#define MIN_ID_PS			1644U
+#define MAX_ID_PS			2260U
+#define DEFAULT_ID_PS			2000U
+
+struct nxp_c45_phy {
+	u32 tx_delay;
+	u32 rx_delay;
+};
+
+struct nxp_c45_phy_stats {
+	const char	*name;
+	u8		mmd;
+	u16		reg;
+	u8		off;
+	u16		mask;
+};
+
+static const struct nxp_c45_phy_stats nxp_c45_hw_stats[] = {
+	{ "phy_symbol_error_cnt", MDIO_MMD_VEND1,
+		VEND1_SYMBOL_ERROR_COUNTER, 0, GENMASK(15, 0) },
+	{ "phy_link_status_drop_cnt", MDIO_MMD_VEND1,
+		VEND1_LINK_DROP_COUNTER, 8, GENMASK(13, 8) },
+	{ "phy_link_availability_drop_cnt", MDIO_MMD_VEND1,
+		VEND1_LINK_DROP_COUNTER, 0, GENMASK(5, 0) },
+	{ "phy_link_loss_cnt", MDIO_MMD_VEND1,
+		VEND1_LINK_LOSSES_AND_FAILURES, 10, GENMASK(15, 10) },
+	{ "phy_link_failure_cnt", MDIO_MMD_VEND1,
+		VEND1_LINK_LOSSES_AND_FAILURES, 0, GENMASK(9, 0) },
+	{ "r_good_frame_cnt", MDIO_MMD_VEND1,
+		VEND1_R_GOOD_FRAME_CNT, 0, GENMASK(15, 0) },
+	{ "r_bad_frame_cnt", MDIO_MMD_VEND1,
+		VEND1_R_BAD_FRAME_CNT, 0, GENMASK(15, 0) },
+	{ "r_rxer_frame_cnt", MDIO_MMD_VEND1,
+		VEND1_R_RXER_FRAME_CNT, 0, GENMASK(15, 0) },
+	{ "rx_preamble_count", MDIO_MMD_VEND1,
+		VEND1_RX_PREAMBLE_COUNT, 0, GENMASK(5, 0) },
+	{ "tx_preamble_count", MDIO_MMD_VEND1,
+		VEND1_TX_PREAMBLE_COUNT, 0, GENMASK(5, 0) },
+	{ "rx_ipg_length", MDIO_MMD_VEND1,
+		VEND1_RX_IPG_LENGTH, 0, GENMASK(8, 0) },
+	{ "tx_ipg_length", MDIO_MMD_VEND1,
+		VEND1_TX_IPG_LENGTH, 0, GENMASK(8, 0) },
+};
+
+static int nxp_c45_get_sset_count(struct phy_device *phydev)
+{
+	return ARRAY_SIZE(nxp_c45_hw_stats);
+}
+
+static void nxp_c45_get_strings(struct phy_device *phydev, u8 *data)
+{
+	size_t i;
+
+	for (i = 0; i < ARRAY_SIZE(nxp_c45_hw_stats); i++) {
+		strncpy(data + i * ETH_GSTRING_LEN,
+			nxp_c45_hw_stats[i].name, ETH_GSTRING_LEN);
+	}
+}
+
+static void nxp_c45_get_stats(struct phy_device *phydev,
+			      struct ethtool_stats *stats, u64 *data)
+{
+	size_t i;
+	int ret;
+
+	for (i = 0; i < ARRAY_SIZE(nxp_c45_hw_stats); i++) {
+		ret = phy_read_mmd(phydev, nxp_c45_hw_stats[i].mmd,
+				   nxp_c45_hw_stats[i].reg);
+		if (ret < 0) {
+			data[i] = U64_MAX;
+		} else {
+			data[i] = ret & nxp_c45_hw_stats[i].mask;
+			data[i] >>= nxp_c45_hw_stats[i].off;
+		}
+	}
+}
+
+static int nxp_c45_config_enable(struct phy_device *phydev)
+{
+	phy_write_mmd(phydev, MDIO_MMD_VEND1, VEND1_DEVICE_CONTROL,
+		      DEVICE_CONTROL_CONFIG_GLOBAL_EN |
+		      DEVICE_CONTROL_CONFIG_ALL_EN);
+	usleep_range(400, 450);
+
+	phy_write_mmd(phydev, MDIO_MMD_VEND1, VEND1_PORT_CONTROL,
+		      PORT_CONTROL_EN);
+	phy_write_mmd(phydev, MDIO_MMD_VEND1, VEND1_PHY_CONTROL,
+		      PHY_CONFIG_EN);
+	phy_write_mmd(phydev, MDIO_MMD_VEND1, VEND1_PORT_INFRA_CONTROL,
+		      PORT_INFRA_CONTROL_EN);
+
+	return 0;
+}
+
+static int nxp_c45_start_op(struct phy_device *phydev)
+{
+	return phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, VEND1_PHY_CONTROL,
+				PHY_START_OP);
+}
+
+static int nxp_c45_soft_reset(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, VEND1_DEVICE_CONTROL,
+			    DEVICE_CONTROL_RESET);
+	if (ret)
+		return ret;
+
+	return phy_read_mmd_poll_timeout(phydev, MDIO_MMD_VEND1,
+					 VEND1_DEVICE_CONTROL, ret,
+					 !(ret & DEVICE_CONTROL_RESET), 20000,
+					 240000, false);
+}
+
+static int nxp_c45_cable_test_start(struct phy_device *phydev)
+{
+	return phy_write_mmd(phydev, MDIO_MMD_VEND1, VEND1_CABLE_TEST,
+			     CABLE_TEST_ENABLE | CABLE_TEST_START);
+}
+
+static int nxp_c45_cable_test_get_status(struct phy_device *phydev,
+					 bool *finished)
+{
+	int ret;
+	u8 cable_test_result;
+
+	ret = phy_read_mmd(phydev, MDIO_MMD_VEND1, VEND1_CABLE_TEST);
+	if (!(ret & CABLE_TEST_VALID)) {
+		*finished = false;
+		return 0;
+	}
+
+	*finished = true;
+	cable_test_result = ret & GENMASK(2, 0);
+
+	switch (cable_test_result) {
+	case CABLE_TEST_OK:
+		ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_A,
+					ETHTOOL_A_CABLE_RESULT_CODE_OK);
+		break;
+	case CABLE_TEST_SHORTED:
+		ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_A,
+					ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT);
+		break;
+	case CABLE_TEST_OPEN:
+		ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_A,
+					ETHTOOL_A_CABLE_RESULT_CODE_OPEN);
+		break;
+	default:
+		ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_A,
+					ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC);
+	}
+
+	phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, VEND1_CABLE_TEST,
+			   CABLE_TEST_ENABLE);
+
+	return nxp_c45_start_op(phydev);
+}
+
+static int nxp_c45_setup_master_slave(struct phy_device *phydev)
+{
+	switch (phydev->master_slave_set) {
+	case MASTER_SLAVE_CFG_MASTER_FORCE:
+	case MASTER_SLAVE_CFG_MASTER_PREFERRED:
+		phy_write_mmd(phydev, MDIO_MMD_PMAPMD, PMAPMD_B100T1_PMAPMD_CTL,
+			      MASTER_MODE);
+		break;
+	case MASTER_SLAVE_CFG_SLAVE_PREFERRED:
+	case MASTER_SLAVE_CFG_SLAVE_FORCE:
+		phy_write_mmd(phydev, MDIO_MMD_PMAPMD, PMAPMD_B100T1_PMAPMD_CTL,
+			      SLAVE_MODE);
+		break;
+	case MASTER_SLAVE_CFG_UNKNOWN:
+	case MASTER_SLAVE_CFG_UNSUPPORTED:
+		return 0;
+	default:
+		phydev_warn(phydev, "Unsupported Master/Slave mode\n");
+		return -EOPNOTSUPP;
+	}
+
+	return 0;
+}
+
+static int nxp_c45_read_master_slave(struct phy_device *phydev)
+{
+	int reg;
+
+	phydev->master_slave_get = MASTER_SLAVE_CFG_UNKNOWN;
+	phydev->master_slave_state = MASTER_SLAVE_STATE_UNKNOWN;
+
+	reg = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, PMAPMD_B100T1_PMAPMD_CTL);
+	if (reg < 0)
+		return reg;
+
+	if (reg & B100T1_PMAPMD_MASTER) {
+		phydev->master_slave_get = MASTER_SLAVE_CFG_MASTER_FORCE;
+		phydev->master_slave_state = MASTER_SLAVE_STATE_MASTER;
+	} else {
+		phydev->master_slave_get = MASTER_SLAVE_CFG_SLAVE_FORCE;
+		phydev->master_slave_state = MASTER_SLAVE_STATE_SLAVE;
+	}
+
+	return 0;
+}
+
+static int nxp_c45_config_aneg(struct phy_device *phydev)
+{
+	return nxp_c45_setup_master_slave(phydev);
+}
+
+static int nxp_c45_read_status(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = genphy_c45_read_status(phydev);
+	if (ret)
+		return ret;
+
+	ret = nxp_c45_read_master_slave(phydev);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int nxp_c45_get_sqi(struct phy_device *phydev)
+{
+	int reg;
+
+	reg = phy_read_mmd(phydev, MDIO_MMD_VEND1, VEND1_SIGNAL_QUALITY);
+	if (!(reg & SQI_VALID))
+		return -EINVAL;
+
+	reg &= SQI_MASK;
+
+	return reg;
+}
+
+static int nxp_c45_get_sqi_max(struct phy_device *phydev)
+{
+	return MAX_SQI;
+}
+
+static int nxp_c45_check_delay(struct phy_device *phydev, u32 delay)
+{
+	if (delay < MIN_ID_PS) {
+		phydev_err(phydev, "delay value smaller than %u\n", MIN_ID_PS);
+		return -EINVAL;
+	}
+
+	if (delay > MAX_ID_PS) {
+		phydev_err(phydev, "delay value higher than %u\n", MAX_ID_PS);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static u64 nxp_c45_get_phase_shift(u64 phase_offset_raw)
+{
+	/* The delay in degree phase is 73.8 + phase_offset_raw * 0.9.
+	 * To avoid floating point operations we'll multiply by 10
+	 * and get 1 decimal point precision.
+	 */
+	phase_offset_raw *= 10;
+	phase_offset_raw -= phase_offset_raw;
+	return div_u64(phase_offset_raw, 9);
+}
+
+static void nxp_c45_disable_delays(struct phy_device *phydev)
+{
+	phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, VEND1_TXID, ID_ENABLE);
+	phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, VEND1_RXID, ID_ENABLE);
+}
+
+static void nxp_c45_set_delays(struct phy_device *phydev)
+{
+	struct nxp_c45_phy *priv = phydev->priv;
+	u64 tx_delay = priv->tx_delay;
+	u64 rx_delay = priv->rx_delay;
+	u64 degree;
+
+	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+	    phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) {
+		degree = div_u64(tx_delay, PS_PER_DEGREE);
+		phy_write_mmd(phydev, MDIO_MMD_VEND1, VEND1_TXID,
+			      ID_ENABLE | nxp_c45_get_phase_shift(degree));
+	} else {
+		phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, VEND1_TXID,
+				   ID_ENABLE);
+	}
+
+	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+	    phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) {
+		degree = div_u64(rx_delay, PS_PER_DEGREE);
+		phy_write_mmd(phydev, MDIO_MMD_VEND1, VEND1_RXID,
+			      ID_ENABLE | nxp_c45_get_phase_shift(degree));
+	} else {
+		phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, VEND1_RXID,
+				   ID_ENABLE);
+	}
+}
+
+static int nxp_c45_get_delays(struct phy_device *phydev)
+{
+	struct nxp_c45_phy *priv = phydev->priv;
+	int ret;
+
+	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+	    phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) {
+		ret = device_property_read_u32(&phydev->mdio.dev,
+					       "tx-internal-delay-ps",
+					       &priv->tx_delay);
+		if (ret)
+			priv->tx_delay = DEFAULT_ID_PS;
+
+		ret = nxp_c45_check_delay(phydev, priv->tx_delay);
+		if (ret) {
+			phydev_err(phydev,
+				   "tx-internal-delay-ps invalid value\n");
+			return ret;
+		}
+	}
+
+	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+	    phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) {
+		ret = device_property_read_u32(&phydev->mdio.dev,
+					       "rx-internal-delay-ps",
+					       &priv->rx_delay);
+		if (ret)
+			priv->rx_delay = DEFAULT_ID_PS;
+
+		ret = nxp_c45_check_delay(phydev, priv->rx_delay);
+		if (ret) {
+			phydev_err(phydev,
+				   "rx-internal-delay-ps invalid value\n");
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static int nxp_c45_set_phy_mode(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = phy_read_mmd(phydev, MDIO_MMD_VEND1, VEND1_ABILITIES);
+	phydev_dbg(phydev, "Clause 45 managed PHY abilities 0x%x\n", ret);
+
+	switch (phydev->interface) {
+	case PHY_INTERFACE_MODE_RGMII:
+		if (!(ret & RGMII_ABILITY)) {
+			phydev_err(phydev, "rgmii mode not supported\n");
+			return -EINVAL;
+		}
+		phy_write_mmd(phydev, MDIO_MMD_VEND1, VEND1_MII_BASIC_CONFIG,
+			      MII_BASIC_CONFIG_RGMII);
+		nxp_c45_disable_delays(phydev);
+		break;
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+		if (!(ret & RGMII_ID_ABILITY)) {
+			phydev_err(phydev, "rgmii-id, rgmii-txid, rgmii-rxid modes are not supported\n");
+			return -EINVAL;
+		}
+		phy_write_mmd(phydev, MDIO_MMD_VEND1, VEND1_MII_BASIC_CONFIG,
+			      MII_BASIC_CONFIG_RGMII);
+		ret = nxp_c45_get_delays(phydev);
+		if (ret)
+			return ret;
+
+		nxp_c45_set_delays(phydev);
+		break;
+	case PHY_INTERFACE_MODE_MII:
+		if (!(ret & MII_ABILITY)) {
+			phydev_err(phydev, "mii mode not supported\n");
+			return -EINVAL;
+		}
+		phy_write_mmd(phydev, MDIO_MMD_VEND1, VEND1_MII_BASIC_CONFIG,
+			      MII_BASIC_CONFIG_MII);
+		break;
+	case PHY_INTERFACE_MODE_REVMII:
+		if (!(ret & REVMII_ABILITY)) {
+			phydev_err(phydev, "rev-mii mode not supported\n");
+			return -EINVAL;
+		}
+		phy_write_mmd(phydev, MDIO_MMD_VEND1, VEND1_MII_BASIC_CONFIG,
+			      MII_BASIC_CONFIG_MII | MII_BASIC_CONFIG_REV);
+		break;
+	case PHY_INTERFACE_MODE_RMII:
+		if (!(ret & RMII_ABILITY)) {
+			phydev_err(phydev, "rmii mode not supported\n");
+			return -EINVAL;
+		}
+		phy_write_mmd(phydev, MDIO_MMD_VEND1, VEND1_MII_BASIC_CONFIG,
+			      MII_BASIC_CONFIG_RMII);
+		break;
+	case PHY_INTERFACE_MODE_SGMII:
+		if (!(ret & SGMII_ABILITY)) {
+			phydev_err(phydev, "sgmii mode not supported\n");
+			return -EINVAL;
+		}
+		phy_write_mmd(phydev, MDIO_MMD_VEND1, VEND1_MII_BASIC_CONFIG,
+			      MII_BASIC_CONFIG_SGMII);
+		break;
+	case PHY_INTERFACE_MODE_INTERNAL:
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int nxp_c45_config_init(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = nxp_c45_config_enable(phydev);
+	if (ret) {
+		phydev_err(phydev, "Failed to enable config\n");
+		return ret;
+	}
+
+	phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, VEND1_PHY_CONFIG,
+			 PHY_CONFIG_AUTO);
+
+	phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, VEND1_LINK_DROP_COUNTER,
+			 COUNTER_EN);
+	phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, VEND1_RX_PREAMBLE_COUNT,
+			 COUNTER_EN);
+	phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, VEND1_TX_PREAMBLE_COUNT,
+			 COUNTER_EN);
+	phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, VEND1_RX_IPG_LENGTH,
+			 COUNTER_EN);
+	phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, VEND1_TX_IPG_LENGTH,
+			 COUNTER_EN);
+
+	ret = nxp_c45_set_phy_mode(phydev);
+	if (ret)
+		return ret;
+
+	phydev->autoneg = AUTONEG_DISABLE;
+
+	return nxp_c45_start_op(phydev);
+}
+
+static int nxp_c45_probe(struct phy_device *phydev)
+{
+	struct nxp_c45_phy *priv;
+
+	priv = devm_kzalloc(&phydev->mdio.dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	phydev->priv = priv;
+
+	return 0;
+}
+
+static struct phy_driver nxp_c45_driver[] = {
+	{
+		PHY_ID_MATCH_MODEL(PHY_ID_TJA_1103),
+		.name			= "NXP C45 TJA1103",
+		.features		= PHY_BASIC_T1_FEATURES,
+		.probe			= nxp_c45_probe,
+		.soft_reset		= nxp_c45_soft_reset,
+		.config_aneg		= nxp_c45_config_aneg,
+		.config_init		= nxp_c45_config_init,
+		.read_status		= nxp_c45_read_status,
+		.suspend		= genphy_c45_pma_suspend,
+		.resume			= genphy_c45_pma_resume,
+		.get_sset_count		= nxp_c45_get_sset_count,
+		.get_strings		= nxp_c45_get_strings,
+		.get_stats		= nxp_c45_get_stats,
+		.cable_test_start	= nxp_c45_cable_test_start,
+		.cable_test_get_status	= nxp_c45_cable_test_get_status,
+		.set_loopback		= genphy_c45_loopback,
+		.get_sqi		= nxp_c45_get_sqi,
+		.get_sqi_max		= nxp_c45_get_sqi_max,
+	},
+};
+
+module_phy_driver(nxp_c45_driver);
+
+static struct mdio_device_id __maybe_unused nxp_c45_tbl[] = {
+	{ PHY_ID_MATCH_MODEL(PHY_ID_TJA_1103) },
+	{ /*sentinel*/ },
+};
+
+MODULE_DEVICE_TABLE(mdio, nxp_c45_tbl);
+
+MODULE_AUTHOR("Radu Pirea <radu-nicolae.pirea@oss.nxp.com>");
+MODULE_DESCRIPTION("NXP C45 PHY driver");
+MODULE_LICENSE("GPL v2");

drivers/net/phy/phy-c45.c

@@ -8,6 +8,49 @@
 #include <linux/mii.h>
 #include <linux/phy.h>
 
+/**
+ * genphy_c45_pma_can_sleep - checks if the PMA have sleep support
+ * @phydev: target phy_device struct
+ */
+static bool genphy_c45_pma_can_sleep(struct phy_device *phydev)
+{
+	int stat1;
+
+	stat1 = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_STAT1);
+	if (stat1 < 0)
+		return false;
+
+	return !!(stat1 & MDIO_STAT1_LPOWERABLE);
+}
+
+/**
+ * genphy_c45_pma_resume - wakes up the PMA module
+ * @phydev: target phy_device struct
+ */
+int genphy_c45_pma_resume(struct phy_device *phydev)
+{
+	if (!genphy_c45_pma_can_sleep(phydev))
+		return -EOPNOTSUPP;
+
+	return phy_clear_bits_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_CTRL1,
+				  MDIO_CTRL1_LPOWER);
+}
+EXPORT_SYMBOL_GPL(genphy_c45_pma_resume);
+
+/**
+ * genphy_c45_pma_suspend - suspends the PMA module
+ * @phydev: target phy_device struct
+ */
+int genphy_c45_pma_suspend(struct phy_device *phydev)
+{
+	if (!genphy_c45_pma_can_sleep(phydev))
+		return -EOPNOTSUPP;
+
+	return phy_set_bits_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_CTRL1,
+				MDIO_CTRL1_LPOWER);
+}
+EXPORT_SYMBOL_GPL(genphy_c45_pma_suspend);
+
 /**
  * genphy_c45_pma_setup_forced - configures a forced speed
  * @phydev: target phy_device struct

include/linux/phy.h

@@ -1535,6 +1535,8 @@ int genphy_c45_pma_read_abilities(struct phy_device *phydev);
 int genphy_c45_read_status(struct phy_device *phydev);
 int genphy_c45_config_aneg(struct phy_device *phydev);
 int genphy_c45_loopback(struct phy_device *phydev, bool enable);
+int genphy_c45_pma_resume(struct phy_device *phydev);
+int genphy_c45_pma_suspend(struct phy_device *phydev);
 
 /* Generic C45 PHY driver */
 extern struct phy_driver genphy_c45_driver;