Merge tag 'mmc-v5.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc

Pull MMC host fixes from Ulf Hansson:

 - dw_mmc: Fix hang on data CRC error

 - mmci: Fix voltage switch procedure for the stm32 variant

 - sdhci-iproc: Fix some clock issues for BCM2711

 - sdhci-msm: Fixup software timeout value

* tag 'mmc-v5.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: sdhci-iproc: Set SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN on BCM2711
  mmc: sdhci-iproc: Cap min clock frequency on BCM2711
  mmc: sdhci-msm: Update the software timeout value for sdhc
  mmc: mmci: stm32: Check when the voltage switch procedure should be done
  mmc: dw_mmc: Fix hang on data CRC error

drivers/mmc/host/dw_mmc.c

@@ -2018,8 +2018,8 @@ static void dw_mci_tasklet_func(struct tasklet_struct *t)
 					continue;
 				}
 
-				dw_mci_stop_dma(host);
 				send_stop_abort(host, data);
+				dw_mci_stop_dma(host);
 				state = STATE_SENDING_STOP;
 				break;
 			}
@@ -2043,10 +2043,10 @@ static void dw_mci_tasklet_func(struct tasklet_struct *t)
 			 */
 			if (test_and_clear_bit(EVENT_DATA_ERROR,
 					       &host->pending_events)) {
-				dw_mci_stop_dma(host);
 				if (!(host->data_status & (SDMMC_INT_DRTO |
 							   SDMMC_INT_EBE)))
 					send_stop_abort(host, data);
+				dw_mci_stop_dma(host);
 				state = STATE_DATA_ERROR;
 				break;
 			}
@@ -2079,10 +2079,10 @@ static void dw_mci_tasklet_func(struct tasklet_struct *t)
 			 */
 			if (test_and_clear_bit(EVENT_DATA_ERROR,
 					       &host->pending_events)) {
-				dw_mci_stop_dma(host);
 				if (!(host->data_status & (SDMMC_INT_DRTO |
 							   SDMMC_INT_EBE)))
 					send_stop_abort(host, data);
+				dw_mci_stop_dma(host);
 				state = STATE_DATA_ERROR;
 				break;
 			}

drivers/mmc/host/mmci_stm32_sdmmc.c

@@ -479,8 +479,9 @@ static int sdmmc_post_sig_volt_switch(struct mmci_host *host,
 	u32 status;
 	int ret = 0;
 
-	if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_180) {
 	spin_lock_irqsave(&host->lock, flags);
+	if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_180 &&
+	    host->pwr_reg & MCI_STM32_VSWITCHEN) {
 		mmci_write_pwrreg(host, host->pwr_reg | MCI_STM32_VSWITCH);
 		spin_unlock_irqrestore(&host->lock, flags);
 
@@ -492,9 +493,11 @@ static int sdmmc_post_sig_volt_switch(struct mmci_host *host,
 
 		writel_relaxed(MCI_STM32_VSWENDC | MCI_STM32_CKSTOPC,
 			       host->base + MMCICLEAR);
+		spin_lock_irqsave(&host->lock, flags);
 		mmci_write_pwrreg(host, host->pwr_reg &
 				  ~(MCI_STM32_VSWITCHEN | MCI_STM32_VSWITCH));
 	}
+	spin_unlock_irqrestore(&host->lock, flags);
 
 	return ret;
 }

drivers/mmc/host/sdhci-iproc.c

@@ -173,6 +173,23 @@ static unsigned int sdhci_iproc_get_max_clock(struct sdhci_host *host)
 		return pltfm_host->clock;
 }
 
+/*
+ * There is a known bug on BCM2711's SDHCI core integration where the
+ * controller will hang when the difference between the core clock and the bus
+ * clock is too great. Specifically this can be reproduced under the following
+ * conditions:
+ *
+ *  - No SD card plugged in, polling thread is running, probing cards at
+ *    100 kHz.
+ *  - BCM2711's core clock configured at 500MHz or more
+ *
+ * So we set 200kHz as the minimum clock frequency available for that SoC.
+ */
+static unsigned int sdhci_iproc_bcm2711_get_min_clock(struct sdhci_host *host)
+{
+	return 200000;
+}
+
 static const struct sdhci_ops sdhci_iproc_ops = {
 	.set_clock = sdhci_set_clock,
 	.get_max_clock = sdhci_iproc_get_max_clock,
@@ -271,13 +288,15 @@ static const struct sdhci_ops sdhci_iproc_bcm2711_ops = {
 	.set_clock = sdhci_set_clock,
 	.set_power = sdhci_set_power_and_bus_voltage,
 	.get_max_clock = sdhci_iproc_get_max_clock,
+	.get_min_clock = sdhci_iproc_bcm2711_get_min_clock,
 	.set_bus_width = sdhci_set_bus_width,
 	.reset = sdhci_reset,
 	.set_uhs_signaling = sdhci_set_uhs_signaling,
 };
 
 static const struct sdhci_pltfm_data sdhci_bcm2711_pltfm_data = {
-	.quirks = SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12,
+	.quirks = SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12 |
+		  SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,
 	.ops = &sdhci_iproc_bcm2711_ops,
 };
 

drivers/mmc/host/sdhci-msm.c

@@ -2089,6 +2089,23 @@ static void sdhci_msm_cqe_disable(struct mmc_host *mmc, bool recovery)
 	sdhci_cqe_disable(mmc, recovery);
 }
 
+static void sdhci_msm_set_timeout(struct sdhci_host *host, struct mmc_command *cmd)
+{
+	u32 count, start = 15;
+
+	__sdhci_set_timeout(host, cmd);
+	count = sdhci_readb(host, SDHCI_TIMEOUT_CONTROL);
+	/*
+	 * Update software timeout value if its value is less than hardware data
+	 * timeout value. Qcom SoC hardware data timeout value was calculated
+	 * using 4 * MCLK * 2^(count + 13). where MCLK = 1 / host->clock.
+	 */
+	if (cmd && cmd->data && host->clock > 400000 &&
+	    host->clock <= 50000000 &&
+	    ((1 << (count + start)) > (10 * host->clock)))
+		host->data_timeout = 22LL * NSEC_PER_SEC;
+}
+
 static const struct cqhci_host_ops sdhci_msm_cqhci_ops = {
 	.enable		= sdhci_msm_cqe_enable,
 	.disable	= sdhci_msm_cqe_disable,
@@ -2438,6 +2455,7 @@ static const struct sdhci_ops sdhci_msm_ops = {
 	.irq	= sdhci_msm_cqe_irq,
 	.dump_vendor_regs = sdhci_msm_dump_vendor_regs,
 	.set_power = sdhci_set_power_noreg,
+	.set_timeout = sdhci_msm_set_timeout,
 };
 
 static const struct sdhci_pltfm_data sdhci_msm_pdata = {