net: ethernet: adi: Add ADIN1110 support

The ADIN1110 is a low power single port 10BASE-T1L MAC-PHY
designed for industrial Ethernet applications. It integrates
an Ethernet PHY core with a MAC and all the associated analog
circuitry, input and output clock buffering.

ADIN1110 MAC-PHY encapsulates the ADIN1100 PHY. The PHY registers
can be accessed through the MDIO MAC registers.
We are registering an MDIO bus with custom read/write in order
to let the PHY to be discovered by the PAL. This will let
the ADIN1100 Linux driver to probe and take control of
the PHY.

The ADIN2111 is a low power, low complexity, two-Ethernet ports
switch with integrated 10BASE-T1L PHYs and one serial peripheral
interface (SPI) port.

The device is designed for industrial Ethernet applications using
low power constrained nodes and is compliant with the IEEE 802.3cg-2019
Ethernet standard for long reach 10 Mbps single pair Ethernet (SPE).
The switch supports various routing configurations between
the two Ethernet ports and the SPI host port providing a flexible
solution for line, daisy-chain, or ring network topologies.

The ADIN2111 supports cable reach of up to 1700 meters with ultra
low power consumption of 77 mW. The two PHY cores support the
1.0 V p-p operating mode and the 2.4 V p-p operating mode defined
in the IEEE 802.3cg standard.

The device integrates the switch, two Ethernet physical layer (PHY)
cores with a media access control (MAC) interface and all the
associated analog circuitry, and input and output clock buffering.

The device also includes internal buffer queues, the SPI and
subsystem registers, as well as the control logic to manage the reset
and clock control and hardware pin configuration.

Access to the PHYs is exposed via an internal MDIO bus. Writes/reads
can be performed by reading/writing to the ADIN2111 MDIO registers
via SPI.

On probe, for each port, a struct net_device is allocated and
registered. When both ports are added to the same bridge, the driver
will enable offloading of frame forwarding at the hardware level.

Driver offers STP support. Normal operation on forwarding state.
Allows only frames with the 802.1d DA to be passed to the host
when in any of the other states.

When both ports of ADIN2111 belong to the same SW bridge a maximum
of 12 FDB entries will offloaded by the hardware and are marked as such.
Co-developed-by: Lennart Franzen <lennart@lfdomain.com>
Signed-off-by: Lennart Franzen <lennart@lfdomain.com>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

drivers/net/ethernet/Kconfig

@@ -121,6 +121,7 @@ config LANTIQ_XRX200
 	  Support for the PMAC of the Gigabit switch (GSWIP) inside the
 	  Lantiq / Intel VRX200 VDSL SoC
 
+source "drivers/net/ethernet/adi/Kconfig"
 source "drivers/net/ethernet/litex/Kconfig"
 source "drivers/net/ethernet/marvell/Kconfig"
 source "drivers/net/ethernet/mediatek/Kconfig"

drivers/net/ethernet/Makefile

@@ -8,6 +8,7 @@ obj-$(CONFIG_NET_VENDOR_8390) += 8390/
 obj-$(CONFIG_NET_VENDOR_ACTIONS) += actions/
 obj-$(CONFIG_NET_VENDOR_ADAPTEC) += adaptec/
 obj-$(CONFIG_GRETH) += aeroflex/
+obj-$(CONFIG_NET_VENDOR_ADI) += adi/
 obj-$(CONFIG_NET_VENDOR_AGERE) += agere/
 obj-$(CONFIG_NET_VENDOR_ALACRITECH) += alacritech/
 obj-$(CONFIG_NET_VENDOR_ALLWINNER) += allwinner/

drivers/net/ethernet/adi/Kconfig

+# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
+#
+# Analog Devices device configuration
+#
+
+config NET_VENDOR_ADI
+	bool "Analog Devices devices"
+	default y
+	depends on SPI
+	help
+	  If you have a network (Ethernet) card belonging to this class, say Y.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about ADI devices. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_ADI
+
+config ADIN1110
+	tristate "Analog Devices ADIN1110 MAC-PHY"
+	depends on SPI && NET_SWITCHDEV
+	select CRC8
+	help
+	  Say yes here to build support for Analog Devices ADIN1110
+	  Low Power 10BASE-T1L Ethernet MAC-PHY.
+
+endif # NET_VENDOR_ADI

drivers/net/ethernet/adi/Makefile

+# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
+#
+# Makefile for the Analog Devices network device drivers.
+#
+
+obj-$(CONFIG_ADIN1110) += adin1110.o