Merge branch 'txgbe'

Mengyuan Lou says:

====================
net: WangXun txgbe/ngbe ethernet driver

This patch series adds support for WangXun NICS, to initialize
interface from software to firmware.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/wangxun/Kconfig

@@ -24,6 +24,7 @@ config LIBWX
 config NGBE
 	tristate "Wangxun(R) GbE PCI Express adapters support"
 	depends on PCI
+	select LIBWX
 	help
 	  This driver supports Wangxun(R) GbE PCI Express family of
 	  adapters.

drivers/net/ethernet/wangxun/libwx/wx_hw.c

@@ -73,6 +73,434 @@ int wx_check_flash_load(struct wx_hw *hw, u32 check_bit)
 }
 EXPORT_SYMBOL(wx_check_flash_load);
 
+void wx_control_hw(struct wx_hw *wxhw, bool drv)
+{
+	if (drv) {
+		/* Let firmware know the driver has taken over */
+		wr32m(wxhw, WX_CFG_PORT_CTL,
+		      WX_CFG_PORT_CTL_DRV_LOAD, WX_CFG_PORT_CTL_DRV_LOAD);
+	} else {
+		/* Let firmware take over control of hw */
+		wr32m(wxhw, WX_CFG_PORT_CTL,
+		      WX_CFG_PORT_CTL_DRV_LOAD, 0);
+	}
+}
+EXPORT_SYMBOL(wx_control_hw);
+
+/**
+ * wx_mng_present - returns 0 when management capability is present
+ * @wxhw: pointer to hardware structure
+ */
+int wx_mng_present(struct wx_hw *wxhw)
+{
+	u32 fwsm;
+
+	fwsm = rd32(wxhw, WX_MIS_ST);
+	if (fwsm & WX_MIS_ST_MNG_INIT_DN)
+		return 0;
+	else
+		return -EACCES;
+}
+EXPORT_SYMBOL(wx_mng_present);
+
+/* Software lock to be held while software semaphore is being accessed. */
+static DEFINE_MUTEX(wx_sw_sync_lock);
+
+/**
+ *  wx_release_sw_sync - Release SW semaphore
+ *  @wxhw: pointer to hardware structure
+ *  @mask: Mask to specify which semaphore to release
+ *
+ *  Releases the SW semaphore for the specified
+ *  function (CSR, PHY0, PHY1, EEPROM, Flash)
+ **/
+static void wx_release_sw_sync(struct wx_hw *wxhw, u32 mask)
+{
+	mutex_lock(&wx_sw_sync_lock);
+	wr32m(wxhw, WX_MNG_SWFW_SYNC, mask, 0);
+	mutex_unlock(&wx_sw_sync_lock);
+}
+
+/**
+ *  wx_acquire_sw_sync - Acquire SW semaphore
+ *  @wxhw: pointer to hardware structure
+ *  @mask: Mask to specify which semaphore to acquire
+ *
+ *  Acquires the SW semaphore for the specified
+ *  function (CSR, PHY0, PHY1, EEPROM, Flash)
+ **/
+static int wx_acquire_sw_sync(struct wx_hw *wxhw, u32 mask)
+{
+	u32 sem = 0;
+	int ret = 0;
+
+	mutex_lock(&wx_sw_sync_lock);
+	ret = read_poll_timeout(rd32, sem, !(sem & mask),
+				5000, 2000000, false, wxhw, WX_MNG_SWFW_SYNC);
+	if (!ret) {
+		sem |= mask;
+		wr32(wxhw, WX_MNG_SWFW_SYNC, sem);
+	} else {
+		wx_err(wxhw, "SW Semaphore not granted: 0x%x.\n", sem);
+	}
+	mutex_unlock(&wx_sw_sync_lock);
+
+	return ret;
+}
+
+/**
+ *  wx_host_interface_command - Issue command to manageability block
+ *  @wxhw: pointer to the HW structure
+ *  @buffer: contains the command to write and where the return status will
+ *   be placed
+ *  @length: length of buffer, must be multiple of 4 bytes
+ *  @timeout: time in ms to wait for command completion
+ *  @return_data: read and return data from the buffer (true) or not (false)
+ *   Needed because FW structures are big endian and decoding of
+ *   these fields can be 8 bit or 16 bit based on command. Decoding
+ *   is not easily understood without making a table of commands.
+ *   So we will leave this up to the caller to read back the data
+ *   in these cases.
+ **/
+int wx_host_interface_command(struct wx_hw *wxhw, u32 *buffer,
+			      u32 length, u32 timeout, bool return_data)
+{
+	u32 hdr_size = sizeof(struct wx_hic_hdr);
+	u32 hicr, i, bi, buf[64] = {};
+	int status = 0;
+	u32 dword_len;
+	u16 buf_len;
+
+	if (length == 0 || length > WX_HI_MAX_BLOCK_BYTE_LENGTH) {
+		wx_err(wxhw, "Buffer length failure buffersize=%d.\n", length);
+		return -EINVAL;
+	}
+
+	status = wx_acquire_sw_sync(wxhw, WX_MNG_SWFW_SYNC_SW_MB);
+	if (status != 0)
+		return status;
+
+	/* Calculate length in DWORDs. We must be DWORD aligned */
+	if ((length % (sizeof(u32))) != 0) {
+		wx_err(wxhw, "Buffer length failure, not aligned to dword");
+		status = -EINVAL;
+		goto rel_out;
+	}
+
+	dword_len = length >> 2;
+
+	/* The device driver writes the relevant command block
+	 * into the ram area.
+	 */
+	for (i = 0; i < dword_len; i++) {
+		wr32a(wxhw, WX_MNG_MBOX, i, (__force u32)cpu_to_le32(buffer[i]));
+		/* write flush */
+		buf[i] = rd32a(wxhw, WX_MNG_MBOX, i);
+	}
+	/* Setting this bit tells the ARC that a new command is pending. */
+	wr32m(wxhw, WX_MNG_MBOX_CTL,
+	      WX_MNG_MBOX_CTL_SWRDY, WX_MNG_MBOX_CTL_SWRDY);
+
+	status = read_poll_timeout(rd32, hicr, hicr & WX_MNG_MBOX_CTL_FWRDY, 1000,
+				   timeout * 1000, false, wxhw, WX_MNG_MBOX_CTL);
+	if (status)
+		goto rel_out;
+
+	/* Check command completion */
+	if (status) {
+		wx_dbg(wxhw, "Command has failed with no status valid.\n");
+
+		buf[0] = rd32(wxhw, WX_MNG_MBOX);
+		if ((buffer[0] & 0xff) != (~buf[0] >> 24)) {
+			status = -EINVAL;
+			goto rel_out;
+		}
+		if ((buf[0] & 0xff0000) >> 16 == 0x80) {
+			wx_dbg(wxhw, "It's unknown cmd.\n");
+			status = -EINVAL;
+			goto rel_out;
+		}
+
+		wx_dbg(wxhw, "write value:\n");
+		for (i = 0; i < dword_len; i++)
+			wx_dbg(wxhw, "%x ", buffer[i]);
+		wx_dbg(wxhw, "read value:\n");
+		for (i = 0; i < dword_len; i++)
+			wx_dbg(wxhw, "%x ", buf[i]);
+	}
+
+	if (!return_data)
+		goto rel_out;
+
+	/* Calculate length in DWORDs */
+	dword_len = hdr_size >> 2;
+
+	/* first pull in the header so we know the buffer length */
+	for (bi = 0; bi < dword_len; bi++) {
+		buffer[bi] = rd32a(wxhw, WX_MNG_MBOX, bi);
+		le32_to_cpus(&buffer[bi]);
+	}
+
+	/* If there is any thing in data position pull it in */
+	buf_len = ((struct wx_hic_hdr *)buffer)->buf_len;
+	if (buf_len == 0)
+		goto rel_out;
+
+	if (length < buf_len + hdr_size) {
+		wx_err(wxhw, "Buffer not large enough for reply message.\n");
+		status = -EFAULT;
+		goto rel_out;
+	}
+
+	/* Calculate length in DWORDs, add 3 for odd lengths */
+	dword_len = (buf_len + 3) >> 2;
+
+	/* Pull in the rest of the buffer (bi is where we left off) */
+	for (; bi <= dword_len; bi++) {
+		buffer[bi] = rd32a(wxhw, WX_MNG_MBOX, bi);
+		le32_to_cpus(&buffer[bi]);
+	}
+
+rel_out:
+	wx_release_sw_sync(wxhw, WX_MNG_SWFW_SYNC_SW_MB);
+	return status;
+}
+EXPORT_SYMBOL(wx_host_interface_command);
+
+/**
+ *  wx_read_ee_hostif_data - Read EEPROM word using a host interface cmd
+ *  assuming that the semaphore is already obtained.
+ *  @wxhw: pointer to hardware structure
+ *  @offset: offset of  word in the EEPROM to read
+ *  @data: word read from the EEPROM
+ *
+ *  Reads a 16 bit word from the EEPROM using the hostif.
+ **/
+static int wx_read_ee_hostif_data(struct wx_hw *wxhw, u16 offset, u16 *data)
+{
+	struct wx_hic_read_shadow_ram buffer;
+	int status;
+
+	buffer.hdr.req.cmd = FW_READ_SHADOW_RAM_CMD;
+	buffer.hdr.req.buf_lenh = 0;
+	buffer.hdr.req.buf_lenl = FW_READ_SHADOW_RAM_LEN;
+	buffer.hdr.req.checksum = FW_DEFAULT_CHECKSUM;
+
+	/* convert offset from words to bytes */
+	buffer.address = (__force u32)cpu_to_be32(offset * 2);
+	/* one word */
+	buffer.length = (__force u16)cpu_to_be16(sizeof(u16));
+
+	status = wx_host_interface_command(wxhw, (u32 *)&buffer, sizeof(buffer),
+					   WX_HI_COMMAND_TIMEOUT, false);
+
+	if (status != 0)
+		return status;
+
+	*data = (u16)rd32a(wxhw, WX_MNG_MBOX, FW_NVM_DATA_OFFSET);
+
+	return status;
+}
+
+/**
+ *  wx_read_ee_hostif - Read EEPROM word using a host interface cmd
+ *  @wxhw: pointer to hardware structure
+ *  @offset: offset of  word in the EEPROM to read
+ *  @data: word read from the EEPROM
+ *
+ *  Reads a 16 bit word from the EEPROM using the hostif.
+ **/
+int wx_read_ee_hostif(struct wx_hw *wxhw, u16 offset, u16 *data)
+{
+	int status = 0;
+
+	status = wx_acquire_sw_sync(wxhw, WX_MNG_SWFW_SYNC_SW_FLASH);
+	if (status == 0) {
+		status = wx_read_ee_hostif_data(wxhw, offset, data);
+		wx_release_sw_sync(wxhw, WX_MNG_SWFW_SYNC_SW_FLASH);
+	}
+
+	return status;
+}
+EXPORT_SYMBOL(wx_read_ee_hostif);
+
+/**
+ *  wx_read_ee_hostif_buffer- Read EEPROM word(s) using hostif
+ *  @wxhw: pointer to hardware structure
+ *  @offset: offset of  word in the EEPROM to read
+ *  @words: number of words
+ *  @data: word(s) read from the EEPROM
+ *
+ *  Reads a 16 bit word(s) from the EEPROM using the hostif.
+ **/
+int wx_read_ee_hostif_buffer(struct wx_hw *wxhw,
+			     u16 offset, u16 words, u16 *data)
+{
+	struct wx_hic_read_shadow_ram buffer;
+	u32 current_word = 0;
+	u16 words_to_read;
+	u32 value = 0;
+	int status;
+	u32 i;
+
+	/* Take semaphore for the entire operation. */
+	status = wx_acquire_sw_sync(wxhw, WX_MNG_SWFW_SYNC_SW_FLASH);
+	if (status != 0)
+		return status;
+
+	while (words) {
+		if (words > FW_MAX_READ_BUFFER_SIZE / 2)
+			words_to_read = FW_MAX_READ_BUFFER_SIZE / 2;
+		else
+			words_to_read = words;
+
+		buffer.hdr.req.cmd = FW_READ_SHADOW_RAM_CMD;
+		buffer.hdr.req.buf_lenh = 0;
+		buffer.hdr.req.buf_lenl = FW_READ_SHADOW_RAM_LEN;
+		buffer.hdr.req.checksum = FW_DEFAULT_CHECKSUM;
+
+		/* convert offset from words to bytes */
+		buffer.address = (__force u32)cpu_to_be32((offset + current_word) * 2);
+		buffer.length = (__force u16)cpu_to_be16(words_to_read * 2);
+
+		status = wx_host_interface_command(wxhw, (u32 *)&buffer,
+						   sizeof(buffer),
+						   WX_HI_COMMAND_TIMEOUT,
+						   false);
+
+		if (status != 0) {
+			wx_err(wxhw, "Host interface command failed\n");
+			goto out;
+		}
+
+		for (i = 0; i < words_to_read; i++) {
+			u32 reg = WX_MNG_MBOX + (FW_NVM_DATA_OFFSET << 2) + 2 * i;
+
+			value = rd32(wxhw, reg);
+			data[current_word] = (u16)(value & 0xffff);
+			current_word++;
+			i++;
+			if (i < words_to_read) {
+				value >>= 16;
+				data[current_word] = (u16)(value & 0xffff);
+				current_word++;
+			}
+		}
+		words -= words_to_read;
+	}
+
+out:
+	wx_release_sw_sync(wxhw, WX_MNG_SWFW_SYNC_SW_FLASH);
+	return status;
+}
+EXPORT_SYMBOL(wx_read_ee_hostif_buffer);
+
+/**
+ *  wx_calculate_checksum - Calculate checksum for buffer
+ *  @buffer: pointer to EEPROM
+ *  @length: size of EEPROM to calculate a checksum for
+ *  Calculates the checksum for some buffer on a specified length.  The
+ *  checksum calculated is returned.
+ **/
+static u8 wx_calculate_checksum(u8 *buffer, u32 length)
+{
+	u8 sum = 0;
+	u32 i;
+
+	if (!buffer)
+		return 0;
+
+	for (i = 0; i < length; i++)
+		sum += buffer[i];
+
+	return (u8)(0 - sum);
+}
+
+/**
+ *  wx_reset_hostif - send reset cmd to fw
+ *  @wxhw: pointer to hardware structure
+ *
+ *  Sends reset cmd to firmware through the manageability
+ *  block.
+ **/
+int wx_reset_hostif(struct wx_hw *wxhw)
+{
+	struct wx_hic_reset reset_cmd;
+	int ret_val = 0;
+	int i;
+
+	reset_cmd.hdr.cmd = FW_RESET_CMD;
+	reset_cmd.hdr.buf_len = FW_RESET_LEN;
+	reset_cmd.hdr.cmd_or_resp.cmd_resv = FW_CEM_CMD_RESERVED;
+	reset_cmd.lan_id = wxhw->bus.func;
+	reset_cmd.reset_type = (u16)wxhw->reset_type;
+	reset_cmd.hdr.checksum = 0;
+	reset_cmd.hdr.checksum = wx_calculate_checksum((u8 *)&reset_cmd,
+						       (FW_CEM_HDR_LEN +
+							reset_cmd.hdr.buf_len));
+
+	for (i = 0; i <= FW_CEM_MAX_RETRIES; i++) {
+		ret_val = wx_host_interface_command(wxhw, (u32 *)&reset_cmd,
+						    sizeof(reset_cmd),
+						    WX_HI_COMMAND_TIMEOUT,
+						    true);
+		if (ret_val != 0)
+			continue;
+
+		if (reset_cmd.hdr.cmd_or_resp.ret_status ==
+		    FW_CEM_RESP_STATUS_SUCCESS)
+			ret_val = 0;
+		else
+			ret_val = -EFAULT;
+
+		break;
+	}
+
+	return ret_val;
+}
+EXPORT_SYMBOL(wx_reset_hostif);
+
+/**
+ *  wx_init_eeprom_params - Initialize EEPROM params
+ *  @wxhw: pointer to hardware structure
+ *
+ *  Initializes the EEPROM parameters wx_eeprom_info within the
+ *  wx_hw struct in order to set up EEPROM access.
+ **/
+void wx_init_eeprom_params(struct wx_hw *wxhw)
+{
+	struct wx_eeprom_info *eeprom = &wxhw->eeprom;
+	u16 eeprom_size;
+	u16 data = 0x80;
+
+	if (eeprom->type == wx_eeprom_uninitialized) {
+		eeprom->semaphore_delay = 10;
+		eeprom->type = wx_eeprom_none;
+
+		if (!(rd32(wxhw, WX_SPI_STATUS) &
+		      WX_SPI_STATUS_FLASH_BYPASS)) {
+			eeprom->type = wx_flash;
+
+			eeprom_size = 4096;
+			eeprom->word_size = eeprom_size >> 1;
+
+			wx_dbg(wxhw, "Eeprom params: type = %d, size = %d\n",
+			       eeprom->type, eeprom->word_size);
+		}
+	}
+
+	if (wxhw->mac.type == wx_mac_sp) {
+		if (wx_read_ee_hostif(wxhw, WX_SW_REGION_PTR, &data)) {
+			wx_err(wxhw, "NVM Read Error\n");
+			return;
+		}
+		data = data >> 1;
+	}
+
+	eeprom->sw_region_offset = data;
+}
+EXPORT_SYMBOL(wx_init_eeprom_params);
+
 /**
  *  wx_get_mac_addr - Generic get MAC address
  *  @wxhw: pointer to hardware structure
@@ -443,6 +871,41 @@ void wx_reset_misc(struct wx_hw *wxhw)
 }
 EXPORT_SYMBOL(wx_reset_misc);
 
+/**
+ *  wx_get_pcie_msix_counts - Gets MSI-X vector count
+ *  @wxhw: pointer to hardware structure
+ *  @msix_count: number of MSI interrupts that can be obtained
+ *  @max_msix_count: number of MSI interrupts that mac need
+ *
+ *  Read PCIe configuration space, and get the MSI-X vector count from
+ *  the capabilities table.
+ **/
+int wx_get_pcie_msix_counts(struct wx_hw *wxhw, u16 *msix_count, u16 max_msix_count)
+{
+	struct pci_dev *pdev = wxhw->pdev;
+	struct device *dev = &pdev->dev;
+	int pos;
+
+	*msix_count = 1;
+	pos = pci_find_capability(pdev, PCI_CAP_ID_MSIX);
+	if (!pos) {
+		dev_err(dev, "Unable to find MSI-X Capabilities\n");
+		return -EINVAL;
+	}
+	pci_read_config_word(pdev,
+			     pos + PCI_MSIX_FLAGS,
+			     msix_count);
+	*msix_count &= WX_PCIE_MSIX_TBL_SZ_MASK;
+	/* MSI-X count is zero-based in HW */
+	*msix_count += 1;
+
+	if (*msix_count > max_msix_count)
+		*msix_count = max_msix_count;
+
+	return 0;
+}
+EXPORT_SYMBOL(wx_get_pcie_msix_counts);
+
 int wx_sw_init(struct wx_hw *wxhw)
 {
 	struct pci_dev *pdev = wxhw->pdev;

drivers/net/ethernet/wangxun/libwx/wx_hw.h

@@ -5,6 +5,15 @@
 #define _WX_HW_H_
 
 int wx_check_flash_load(struct wx_hw *hw, u32 check_bit);
+void wx_control_hw(struct wx_hw *wxhw, bool drv);
+int wx_mng_present(struct wx_hw *wxhw);
+int wx_host_interface_command(struct wx_hw *wxhw, u32 *buffer,
+			      u32 length, u32 timeout, bool return_data);
+int wx_read_ee_hostif(struct wx_hw *wxhw, u16 offset, u16 *data);
+int wx_read_ee_hostif_buffer(struct wx_hw *wxhw,
+			     u16 offset, u16 words, u16 *data);
+int wx_reset_hostif(struct wx_hw *wxhw);
+void wx_init_eeprom_params(struct wx_hw *wxhw);
 void wx_get_mac_addr(struct wx_hw *wxhw, u8 *mac_addr);
 int wx_set_rar(struct wx_hw *wxhw, u32 index, u8 *addr, u64 pools, u32 enable_addr);
 int wx_clear_rar(struct wx_hw *wxhw, u32 index);
@@ -13,6 +22,7 @@ void wx_disable_rx(struct wx_hw *wxhw);
 int wx_disable_pcie_master(struct wx_hw *wxhw);
 int wx_stop_adapter(struct wx_hw *wxhw);
 void wx_reset_misc(struct wx_hw *wxhw);
+int wx_get_pcie_msix_counts(struct wx_hw *wxhw, u16 *msix_count, u16 max_msix_count);
 int wx_sw_init(struct wx_hw *wxhw);
 
 #endif /* _WX_HW_H_ */

drivers/net/ethernet/wangxun/libwx/wx_type.h

@@ -14,11 +14,20 @@
 #define WX_WOL_SUP                              0x4000
 #define WX_WOL_MASK                             0x4000
 
+/* MSI-X capability fields masks */
+#define WX_PCIE_MSIX_TBL_SZ_MASK                0x7FF
+#define WX_PCI_LINK_STATUS                      0xB2
+
 /**************** Global Registers ****************************/
 /* chip control Registers */
 #define WX_MIS_PWR                   0x10000
 #define WX_MIS_RST                   0x1000C
 #define WX_MIS_RST_LAN_RST(_i)       BIT((_i) + 1)
+#define WX_MIS_RST_SW_RST            BIT(0)
+#define WX_MIS_ST                    0x10028
+#define WX_MIS_ST_MNG_INIT_DN        BIT(0)
+#define WX_MIS_SWSM                  0x1002C
+#define WX_MIS_SWSM_SMBI             BIT(0)
 #define WX_MIS_RST_ST                0x10030
 #define WX_MIS_RST_ST_RST_INI_SHIFT  8
 #define WX_MIS_RST_ST_RST_INIT       (0xFF << WX_MIS_RST_ST_RST_INI_SHIFT)
@@ -51,6 +60,11 @@
 #define WX_TS_ALARM_ST_DALARM        BIT(1)
 #define WX_TS_ALARM_ST_ALARM         BIT(0)
 
+/************************* Port Registers ************************************/
+/* port cfg Registers */
+#define WX_CFG_PORT_CTL              0x14400
+#define WX_CFG_PORT_CTL_DRV_LOAD     BIT(3)
+
 /*********************** Transmit DMA registers **************************/
 /* transmit global control */
 #define WX_TDM_CTL                   0x18000
@@ -107,6 +121,15 @@
 #define WX_PSR_MAC_SWC_IDX           0x16210
 #define WX_CLEAR_VMDQ_ALL            0xFFFFFFFFU
 
+/************************************** MNG ********************************/
+#define WX_MNG_SWFW_SYNC             0x1E008
+#define WX_MNG_SWFW_SYNC_SW_MB       BIT(2)
+#define WX_MNG_SWFW_SYNC_SW_FLASH    BIT(3)
+#define WX_MNG_MBOX                  0x1E100
+#define WX_MNG_MBOX_CTL              0x1E044
+#define WX_MNG_MBOX_CTL_SWRDY        BIT(0)
+#define WX_MNG_MBOX_CTL_FWRDY        BIT(2)
+
 /************************************* ETH MAC *****************************/
 #define WX_MAC_TX_CFG                0x11000
 #define WX_MAC_TX_CFG_TE             BIT(0)
@@ -144,6 +167,70 @@
 /* Number of 80 microseconds we wait for PCI Express master disable */
 #define WX_PCI_MASTER_DISABLE_TIMEOUT        80000
 
+/****************** Manageablility Host Interface defines ********************/
+#define WX_HI_MAX_BLOCK_BYTE_LENGTH  256 /* Num of bytes in range */
+#define WX_HI_COMMAND_TIMEOUT        1000 /* Process HI command limit */
+
+#define FW_READ_SHADOW_RAM_CMD       0x31
+#define FW_READ_SHADOW_RAM_LEN       0x6
+#define FW_DEFAULT_CHECKSUM          0xFF /* checksum always 0xFF */
+#define FW_NVM_DATA_OFFSET           3
+#define FW_MAX_READ_BUFFER_SIZE      244
+#define FW_RESET_CMD                 0xDF
+#define FW_RESET_LEN                 0x2
+#define FW_CEM_HDR_LEN               0x4
+#define FW_CEM_CMD_RESERVED          0X0
+#define FW_CEM_MAX_RETRIES           3
+#define FW_CEM_RESP_STATUS_SUCCESS   0x1
+
+#define WX_SW_REGION_PTR             0x1C
+
+/* Host Interface Command Structures */
+struct wx_hic_hdr {
+	u8 cmd;
+	u8 buf_len;
+	union {
+		u8 cmd_resv;
+		u8 ret_status;
+	} cmd_or_resp;
+	u8 checksum;
+};
+
+struct wx_hic_hdr2_req {
+	u8 cmd;
+	u8 buf_lenh;
+	u8 buf_lenl;
+	u8 checksum;
+};
+
+struct wx_hic_hdr2_rsp {
+	u8 cmd;
+	u8 buf_lenl;
+	u8 buf_lenh_status;     /* 7-5: high bits of buf_len, 4-0: status */
+	u8 checksum;
+};
+
+union wx_hic_hdr2 {
+	struct wx_hic_hdr2_req req;
+	struct wx_hic_hdr2_rsp rsp;
+};
+
+/* These need to be dword aligned */
+struct wx_hic_read_shadow_ram {
+	union wx_hic_hdr2 hdr;
+	u32 address;
+	u16 length;
+	u16 pad2;
+	u16 data;
+	u16 pad3;
+};
+
+struct wx_hic_reset {
+	struct wx_hic_hdr hdr;
+	u16 lan_id;
+	u16 reset_type;
+};
+
 /* Bus parameters */
 struct wx_bus_info {
 	u8 func;
@@ -172,20 +259,43 @@ struct wx_mac_info {
 	u32 num_rar_entries;
 	u32 max_tx_queues;
 	u32 max_rx_queues;
+
+	u16 max_msix_vectors;
 	struct wx_thermal_sensor_data sensor;
 };
 
+enum wx_eeprom_type {
+	wx_eeprom_uninitialized = 0,
+	wx_eeprom_spi,
+	wx_flash,
+	wx_eeprom_none /* No NVM support */
+};
+
+struct wx_eeprom_info {
+	enum wx_eeprom_type type;
+	u32 semaphore_delay;
+	u16 word_size;
+	u16 sw_region_offset;
+};
+
 struct wx_addr_filter_info {
 	u32 num_mc_addrs;
 	u32 mta_in_use;
 	bool user_set_promisc;
 };
 
+enum wx_reset_type {
+	WX_LAN_RESET = 0,
+	WX_SW_RESET,
+	WX_GLOBAL_RESET
+};
+
 struct wx_hw {
 	u8 __iomem *hw_addr;
 	struct pci_dev *pdev;
 	struct wx_bus_info bus;
 	struct wx_mac_info mac;
+	struct wx_eeprom_info eeprom;
 	struct wx_addr_filter_info addr_ctrl;
 	u16 device_id;
 	u16 vendor_id;
@@ -195,6 +305,7 @@ struct wx_hw {
 	u16 oem_ssid;
 	u16 oem_svid;
 	bool adapter_stopped;
+	enum wx_reset_type reset_type;
 };
 
 #define WX_INTR_ALL (~0ULL)
@@ -202,6 +313,10 @@ struct wx_hw {
 /* register operations */
 #define wr32(a, reg, value)	writel((value), ((a)->hw_addr + (reg)))
 #define rd32(a, reg)		readl((a)->hw_addr + (reg))
+#define rd32a(a, reg, offset) ( \
+	rd32((a), (reg) + ((offset) << 2)))
+#define wr32a(a, reg, off, val) \
+	wr32((a), (reg) + ((off) << 2), (val))
 
 static inline u32
 rd32m(struct wx_hw *wxhw, u32 reg, u32 mask)

drivers/net/ethernet/wangxun/ngbe/Makefile

@@ -6,4 +6,4 @@
 
 obj-$(CONFIG_NGBE) += ngbe.o
 
-ngbe-objs := ngbe_main.o
+ngbe-objs := ngbe_main.o ngbe_hw.o

drivers/net/ethernet/wangxun/ngbe/ngbe.h

@@ -11,12 +11,67 @@
 #define NGBE_MAX_RX_QUEUES		(NGBE_MAX_FDIR_INDICES + 1)
 #define NGBE_MAX_TX_QUEUES		(NGBE_MAX_FDIR_INDICES + 1)
 
+#define NGBE_ETH_LENGTH_OF_ADDRESS	6
+#define NGBE_MAX_MSIX_VECTORS		0x09
+#define NGBE_RAR_ENTRIES		32
+
+/* TX/RX descriptor defines */
+#define NGBE_DEFAULT_TXD		512 /* default ring size */
+#define NGBE_DEFAULT_TX_WORK		256
+#define NGBE_MAX_TXD			8192
+#define NGBE_MIN_TXD			128
+
+#define NGBE_DEFAULT_RXD		512 /* default ring size */
+#define NGBE_DEFAULT_RX_WORK		256
+#define NGBE_MAX_RXD			8192
+#define NGBE_MIN_RXD			128
+
+#define NGBE_MAC_STATE_DEFAULT		0x1
+#define NGBE_MAC_STATE_MODIFIED		0x2
+#define NGBE_MAC_STATE_IN_USE		0x4
+
+struct ngbe_mac_addr {
+	u8 addr[ETH_ALEN];
+	u16 state; /* bitmask */
+	u64 pools;
+};
+
 /* board specific private data structure */
 struct ngbe_adapter {
 	u8 __iomem *io_addr;    /* Mainly for iounmap use */
 	/* OS defined structs */
 	struct net_device *netdev;
 	struct pci_dev *pdev;
+
+	/* structs defined in ngbe_hw.h */
+	struct ngbe_hw hw;
+	struct ngbe_mac_addr *mac_table;
+	u16 msg_enable;
+
+	/* Tx fast path data */
+	int num_tx_queues;
+	u16 tx_itr_setting;
+	u16 tx_work_limit;
+
+	/* Rx fast path data */
+	int num_rx_queues;
+	u16 rx_itr_setting;
+	u16 rx_work_limit;
+
+	int num_q_vectors;      /* current number of q_vectors for device */
+	int max_q_vectors;      /* upper limit of q_vectors for device */
+
+	u32 tx_ring_count;
+	u32 rx_ring_count;
+
+#define NGBE_MAX_RETA_ENTRIES 128
+	u8 rss_indir_tbl[NGBE_MAX_RETA_ENTRIES];
+
+#define NGBE_RSS_KEY_SIZE     40  /* size of RSS Hash Key in bytes */
+	u32 *rss_key;
+	u32 wol;
+
+	u16 bd_number;
 };
 
 extern char ngbe_driver_name[];

drivers/net/ethernet/wangxun/ngbe/ngbe_hw.c

+// SPDX-License-Identifier: GPL-2.0
+/* Copyright (c) 2019 - 2022 Beijing WangXun Technology Co., Ltd. */
+
+#include <linux/etherdevice.h>
+#include <linux/iopoll.h>
+#include <linux/pci.h>
+
+#include "../libwx/wx_type.h"
+#include "../libwx/wx_hw.h"
+#include "ngbe_type.h"
+#include "ngbe_hw.h"
+#include "ngbe.h"
+
+int ngbe_eeprom_chksum_hostif(struct ngbe_hw *hw)
+{
+	struct wx_hic_read_shadow_ram buffer;
+	struct wx_hw *wxhw = &hw->wxhw;
+	int status;
+	int tmp;
+
+	buffer.hdr.req.cmd = NGBE_FW_EEPROM_CHECKSUM_CMD;
+	buffer.hdr.req.buf_lenh = 0;
+	buffer.hdr.req.buf_lenl = 0;
+	buffer.hdr.req.checksum = NGBE_FW_CMD_DEFAULT_CHECKSUM;
+	/* convert offset from words to bytes */
+	buffer.address = 0;
+	/* one word */
+	buffer.length = 0;
+
+	status = wx_host_interface_command(wxhw, (u32 *)&buffer, sizeof(buffer),
+					   WX_HI_COMMAND_TIMEOUT, false);
+
+	if (status < 0)
+		return status;
+	tmp = rd32a(wxhw, WX_MNG_MBOX, 1);
+	if (tmp == NGBE_FW_CMD_ST_PASS)
+		return 0;
+	return -EIO;
+}
+
+static int ngbe_reset_misc(struct ngbe_hw *hw)
+{
+	struct wx_hw *wxhw = &hw->wxhw;
+
+	wx_reset_misc(wxhw);
+	if (hw->mac_type == ngbe_mac_type_rgmii)
+		wr32(wxhw, NGBE_MDIO_CLAUSE_SELECT, 0xF);
+	if (hw->gpio_ctrl) {
+		/* gpio0 is used to power on/off control*/
+		wr32(wxhw, NGBE_GPIO_DDR, 0x1);
+		wr32(wxhw, NGBE_GPIO_DR, NGBE_GPIO_DR_0);
+	}
+	return 0;
+}
+
+/**
+ *  ngbe_reset_hw - Perform hardware reset
+ *  @hw: pointer to hardware structure
+ *
+ *  Resets the hardware by resetting the transmit and receive units, masks
+ *  and clears all interrupts, perform a PHY reset, and perform a link (MAC)
+ *  reset.
+ **/
+int ngbe_reset_hw(struct ngbe_hw *hw)
+{
+	struct wx_hw *wxhw = &hw->wxhw;
+	int status = 0;
+	u32 reset = 0;
+
+	/* Call adapter stop to disable tx/rx and clear interrupts */
+	status = wx_stop_adapter(wxhw);
+	if (status != 0)
+		return status;
+	reset = WX_MIS_RST_LAN_RST(wxhw->bus.func);
+	wr32(wxhw, WX_MIS_RST, reset | rd32(wxhw, WX_MIS_RST));
+	ngbe_reset_misc(hw);
+
+	/* Store the permanent mac address */
+	wx_get_mac_addr(wxhw, wxhw->mac.perm_addr);
+
+	/* reset num_rar_entries to 128 */
+	wxhw->mac.num_rar_entries = NGBE_RAR_ENTRIES;
+	wx_init_rx_addrs(wxhw);
+	pci_set_master(wxhw->pdev);
+
+	return 0;
+}

drivers/net/ethernet/wangxun/ngbe/ngbe_hw.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * WangXun Gigabit PCI Express Linux driver
+ * Copyright (c) 2019 - 2022 Beijing WangXun Technology Co., Ltd.
+ */
+
+#ifndef _NGBE_HW_H_
+#define _NGBE_HW_H_
+
+int ngbe_eeprom_chksum_hostif(struct ngbe_hw *hw);
+int ngbe_reset_hw(struct ngbe_hw *hw);
+#endif /* _NGBE_HW_H_ */

drivers/net/ethernet/wangxun/ngbe/ngbe_main.c

@@ -8,7 +8,12 @@
 #include <linux/string.h>
 #include <linux/aer.h>
 #include <linux/etherdevice.h>
+#include <net/ip.h>
 
+#include "../libwx/wx_type.h"
+#include "../libwx/wx_hw.h"
+#include "ngbe_type.h"
+#include "ngbe_hw.h"
 #include "ngbe.h"
 char ngbe_driver_name[] = "ngbe";
 
@@ -34,6 +39,247 @@ static const struct pci_device_id ngbe_pci_tbl[] = {
 	{ .device = 0 }
 };
 
+static void ngbe_mac_set_default_filter(struct ngbe_adapter *adapter, u8 *addr)
+{
+	struct ngbe_hw *hw = &adapter->hw;
+
+	memcpy(&adapter->mac_table[0].addr, addr, ETH_ALEN);
+	adapter->mac_table[0].pools = 1ULL;
+	adapter->mac_table[0].state = (NGBE_MAC_STATE_DEFAULT |
+				       NGBE_MAC_STATE_IN_USE);
+	wx_set_rar(&hw->wxhw, 0, adapter->mac_table[0].addr,
+		   adapter->mac_table[0].pools,
+		   WX_PSR_MAC_SWC_AD_H_AV);
+}
+
+/**
+ *  ngbe_init_type_code - Initialize the shared code
+ *  @hw: pointer to hardware structure
+ **/
+static void ngbe_init_type_code(struct ngbe_hw *hw)
+{
+	int wol_mask = 0, ncsi_mask = 0;
+	struct wx_hw *wxhw = &hw->wxhw;
+	u16 type_mask = 0;
+
+	wxhw->mac.type = wx_mac_em;
+	type_mask = (u16)(wxhw->subsystem_device_id & NGBE_OEM_MASK);
+	ncsi_mask = wxhw->subsystem_device_id & NGBE_NCSI_MASK;
+	wol_mask = wxhw->subsystem_device_id & NGBE_WOL_MASK;
+
+	switch (type_mask) {
+	case NGBE_SUBID_M88E1512_SFP:
+	case NGBE_SUBID_LY_M88E1512_SFP:
+		hw->phy.type = ngbe_phy_m88e1512_sfi;
+		break;
+	case NGBE_SUBID_M88E1512_RJ45:
+		hw->phy.type = ngbe_phy_m88e1512;
+		break;
+	case NGBE_SUBID_M88E1512_MIX:
+		hw->phy.type = ngbe_phy_m88e1512_unknown;
+		break;
+	case NGBE_SUBID_YT8521S_SFP:
+	case NGBE_SUBID_YT8521S_SFP_GPIO:
+	case NGBE_SUBID_LY_YT8521S_SFP:
+		hw->phy.type = ngbe_phy_yt8521s_sfi;
+		break;
+	case NGBE_SUBID_INTERNAL_YT8521S_SFP:
+	case NGBE_SUBID_INTERNAL_YT8521S_SFP_GPIO:
+		hw->phy.type = ngbe_phy_internal_yt8521s_sfi;
+		break;
+	case NGBE_SUBID_RGMII_FPGA:
+	case NGBE_SUBID_OCP_CARD:
+		fallthrough;
+	default:
+		hw->phy.type = ngbe_phy_internal;
+		break;
+	}
+
+	if (hw->phy.type == ngbe_phy_internal ||
+	    hw->phy.type == ngbe_phy_internal_yt8521s_sfi)
+		hw->mac_type = ngbe_mac_type_mdi;
+	else
+		hw->mac_type = ngbe_mac_type_rgmii;
+
+	hw->wol_enabled = (wol_mask == NGBE_WOL_SUP) ? 1 : 0;
+	hw->ncsi_enabled = (ncsi_mask == NGBE_NCSI_MASK ||
+			   type_mask == NGBE_SUBID_OCP_CARD) ? 1 : 0;
+
+	switch (type_mask) {
+	case NGBE_SUBID_LY_YT8521S_SFP:
+	case NGBE_SUBID_LY_M88E1512_SFP:
+	case NGBE_SUBID_YT8521S_SFP_GPIO:
+	case NGBE_SUBID_INTERNAL_YT8521S_SFP_GPIO:
+		hw->gpio_ctrl = 1;
+		break;
+	default:
+		hw->gpio_ctrl = 0;
+		break;
+	}
+}
+
+/**
+ * ngbe_init_rss_key - Initialize adapter RSS key
+ * @adapter: device handle
+ *
+ * Allocates and initializes the RSS key if it is not allocated.
+ **/
+static inline int ngbe_init_rss_key(struct ngbe_adapter *adapter)
+{
+	u32 *rss_key;
+
+	if (!adapter->rss_key) {
+		rss_key = kzalloc(NGBE_RSS_KEY_SIZE, GFP_KERNEL);
+		if (unlikely(!rss_key))
+			return -ENOMEM;
+
+		netdev_rss_key_fill(rss_key, NGBE_RSS_KEY_SIZE);
+		adapter->rss_key = rss_key;
+	}
+
+	return 0;
+}
+
+/**
+ * ngbe_sw_init - Initialize general software structures
+ * @adapter: board private structure to initialize
+ **/
+static int ngbe_sw_init(struct ngbe_adapter *adapter)
+{
+	struct pci_dev *pdev = adapter->pdev;
+	struct ngbe_hw *hw = &adapter->hw;
+	struct wx_hw *wxhw = &hw->wxhw;
+	u16 msix_count = 0;
+	int err = 0;
+
+	wxhw->hw_addr = adapter->io_addr;
+	wxhw->pdev = pdev;
+
+	/* PCI config space info */
+	err = wx_sw_init(wxhw);
+	if (err < 0) {
+		netif_err(adapter, probe, adapter->netdev,
+			  "Read of internal subsystem device id failed\n");
+		return err;
+	}
+
+	/* mac type, phy type , oem type */
+	ngbe_init_type_code(hw);
+
+	wxhw->mac.max_rx_queues = NGBE_MAX_RX_QUEUES;
+	wxhw->mac.max_tx_queues = NGBE_MAX_TX_QUEUES;
+	wxhw->mac.num_rar_entries = NGBE_RAR_ENTRIES;
+	/* Set common capability flags and settings */
+	adapter->max_q_vectors = NGBE_MAX_MSIX_VECTORS;
+
+	err = wx_get_pcie_msix_counts(wxhw, &msix_count, NGBE_MAX_MSIX_VECTORS);
+	if (err)
+		dev_err(&pdev->dev, "Do not support MSI-X\n");
+	wxhw->mac.max_msix_vectors = msix_count;
+
+	adapter->mac_table = kcalloc(wxhw->mac.num_rar_entries,
+				     sizeof(struct ngbe_mac_addr),
+				     GFP_KERNEL);
+	if (!adapter->mac_table) {
+		dev_err(&pdev->dev, "mac_table allocation failed: %d\n", err);
+		return -ENOMEM;
+	}
+
+	if (ngbe_init_rss_key(adapter))
+		return -ENOMEM;
+
+	/* enable itr by default in dynamic mode */
+	adapter->rx_itr_setting = 1;
+	adapter->tx_itr_setting = 1;
+
+	/* set default ring sizes */
+	adapter->tx_ring_count = NGBE_DEFAULT_TXD;
+	adapter->rx_ring_count = NGBE_DEFAULT_RXD;
+
+	/* set default work limits */
+	adapter->tx_work_limit = NGBE_DEFAULT_TX_WORK;
+	adapter->rx_work_limit = NGBE_DEFAULT_RX_WORK;
+
+	return 0;
+}
+
+static void ngbe_down(struct ngbe_adapter *adapter)
+{
+	netif_carrier_off(adapter->netdev);
+	netif_tx_disable(adapter->netdev);
+};
+
+/**
+ * ngbe_open - Called when a network interface is made active
+ * @netdev: network interface device structure
+ *
+ * Returns 0 on success, negative value on failure
+ *
+ * The open entry point is called when a network interface is made
+ * active by the system (IFF_UP).
+ **/
+static int ngbe_open(struct net_device *netdev)
+{
+	struct ngbe_adapter *adapter = netdev_priv(netdev);
+	struct ngbe_hw *hw = &adapter->hw;
+	struct wx_hw *wxhw = &hw->wxhw;
+
+	wx_control_hw(wxhw, true);
+
+	return 0;
+}
+
+/**
+ * ngbe_close - Disables a network interface
+ * @netdev: network interface device structure
+ *
+ * Returns 0, this is not allowed to fail
+ *
+ * The close entry point is called when an interface is de-activated
+ * by the OS.  The hardware is still under the drivers control, but
+ * needs to be disabled.  A global MAC reset is issued to stop the
+ * hardware, and all transmit and receive resources are freed.
+ **/
+static int ngbe_close(struct net_device *netdev)
+{
+	struct ngbe_adapter *adapter = netdev_priv(netdev);
+
+	ngbe_down(adapter);
+	wx_control_hw(&adapter->hw.wxhw, false);
+
+	return 0;
+}
+
+static netdev_tx_t ngbe_xmit_frame(struct sk_buff *skb,
+				   struct net_device *netdev)
+{
+	return NETDEV_TX_OK;
+}
+
+/**
+ * ngbe_set_mac - Change the Ethernet Address of the NIC
+ * @netdev: network interface device structure
+ * @p: pointer to an address structure
+ *
+ * Returns 0 on success, negative on failure
+ **/
+static int ngbe_set_mac(struct net_device *netdev, void *p)
+{
+	struct ngbe_adapter *adapter = netdev_priv(netdev);
+	struct wx_hw *wxhw = &adapter->hw.wxhw;
+	struct sockaddr *addr = p;
+
+	if (!is_valid_ether_addr(addr->sa_data))
+		return -EADDRNOTAVAIL;
+
+	eth_hw_addr_set(netdev, addr->sa_data);
+	memcpy(wxhw->mac.addr, addr->sa_data, netdev->addr_len);
+
+	ngbe_mac_set_default_filter(adapter, wxhw->mac.addr);
+
+	return 0;
+}
+
 static void ngbe_dev_shutdown(struct pci_dev *pdev, bool *enable_wake)
 {
 	struct ngbe_adapter *adapter = pci_get_drvdata(pdev);
@@ -41,13 +287,22 @@ static void ngbe_dev_shutdown(struct pci_dev *pdev, bool *enable_wake)
 
 	netif_device_detach(netdev);
 
+	rtnl_lock();
+	if (netif_running(netdev))
+		ngbe_down(adapter);
+	rtnl_unlock();
+	wx_control_hw(&adapter->hw.wxhw, false);
+
 	pci_disable_device(pdev);
 }
 
 static void ngbe_shutdown(struct pci_dev *pdev)
 {
+	struct ngbe_adapter *adapter = pci_get_drvdata(pdev);
 	bool wake;
 
+	wake = !!adapter->wol;
+
 	ngbe_dev_shutdown(pdev, &wake);
 
 	if (system_state == SYSTEM_POWER_OFF) {
@@ -56,6 +311,14 @@ static void ngbe_shutdown(struct pci_dev *pdev)
 	}
 }
 
+static const struct net_device_ops ngbe_netdev_ops = {
+	.ndo_open               = ngbe_open,
+	.ndo_stop               = ngbe_close,
+	.ndo_start_xmit         = ngbe_xmit_frame,
+	.ndo_validate_addr      = eth_validate_addr,
+	.ndo_set_mac_address    = ngbe_set_mac,
+};
+
 /**
  * ngbe_probe - Device Initialization Routine
  * @pdev: PCI device information struct
@@ -71,7 +334,14 @@ static int ngbe_probe(struct pci_dev *pdev,
 		      const struct pci_device_id __always_unused *ent)
 {
 	struct ngbe_adapter *adapter = NULL;
+	struct ngbe_hw *hw = NULL;
+	struct wx_hw *wxhw = NULL;
 	struct net_device *netdev;
+	u32 e2rom_cksum_cap = 0;
+	static int func_nums;
+	u16 e2rom_ver = 0;
+	u32 etrack_id = 0;
+	u32 saved_ver = 0;
 	int err;
 
 	err = pci_enable_device_mem(pdev);
@@ -111,6 +381,9 @@ static int ngbe_probe(struct pci_dev *pdev,
 	adapter = netdev_priv(netdev);
 	adapter->netdev = netdev;
 	adapter->pdev = pdev;
+	hw = &adapter->hw;
+	wxhw = &hw->wxhw;
+	adapter->msg_enable = BIT(3) - 1;
 
 	adapter->io_addr = devm_ioremap(&pdev->dev,
 					pci_resource_start(pdev, 0),
@@ -120,12 +393,101 @@ static int ngbe_probe(struct pci_dev *pdev,
 		goto err_pci_release_regions;
 	}
 
+	netdev->netdev_ops = &ngbe_netdev_ops;
+
 	netdev->features |= NETIF_F_HIGHDMA;
 
+	adapter->bd_number = func_nums;
+	/* setup the private structure */
+	err = ngbe_sw_init(adapter);
+	if (err)
+		goto err_free_mac_table;
+
+	/* check if flash load is done after hw power up */
+	err = wx_check_flash_load(wxhw, NGBE_SPI_ILDR_STATUS_PERST);
+	if (err)
+		goto err_free_mac_table;
+	err = wx_check_flash_load(wxhw, NGBE_SPI_ILDR_STATUS_PWRRST);
+	if (err)
+		goto err_free_mac_table;
+
+	err = wx_mng_present(wxhw);
+	if (err) {
+		dev_err(&pdev->dev, "Management capability is not present\n");
+		goto err_free_mac_table;
+	}
+
+	err = ngbe_reset_hw(hw);
+	if (err) {
+		dev_err(&pdev->dev, "HW Init failed: %d\n", err);
+		goto err_free_mac_table;
+	}
+
+	if (wxhw->bus.func == 0) {
+		wr32(wxhw, NGBE_CALSUM_CAP_STATUS, 0x0);
+		wr32(wxhw, NGBE_EEPROM_VERSION_STORE_REG, 0x0);
+	} else {
+		e2rom_cksum_cap = rd32(wxhw, NGBE_CALSUM_CAP_STATUS);
+		saved_ver = rd32(wxhw, NGBE_EEPROM_VERSION_STORE_REG);
+	}
+
+	wx_init_eeprom_params(wxhw);
+	if (wxhw->bus.func == 0 || e2rom_cksum_cap == 0) {
+		/* make sure the EEPROM is ready */
+		err = ngbe_eeprom_chksum_hostif(hw);
+		if (err) {
+			dev_err(&pdev->dev, "The EEPROM Checksum Is Not Valid\n");
+			err = -EIO;
+			goto err_free_mac_table;
+		}
+	}
+
+	adapter->wol = 0;
+	if (hw->wol_enabled)
+		adapter->wol = NGBE_PSR_WKUP_CTL_MAG;
+
+	hw->wol_enabled = !!(adapter->wol);
+	wr32(wxhw, NGBE_PSR_WKUP_CTL, adapter->wol);
+
+	device_set_wakeup_enable(&pdev->dev, adapter->wol);
+
+	/* Save off EEPROM version number and Option Rom version which
+	 * together make a unique identify for the eeprom
+	 */
+	if (saved_ver) {
+		etrack_id = saved_ver;
+	} else {
+		wx_read_ee_hostif(wxhw,
+				  wxhw->eeprom.sw_region_offset + NGBE_EEPROM_VERSION_H,
+				  &e2rom_ver);
+		etrack_id = e2rom_ver << 16;
+		wx_read_ee_hostif(wxhw,
+				  wxhw->eeprom.sw_region_offset + NGBE_EEPROM_VERSION_L,
+				  &e2rom_ver);
+		etrack_id |= e2rom_ver;
+		wr32(wxhw, NGBE_EEPROM_VERSION_STORE_REG, etrack_id);
+	}
+
+	eth_hw_addr_set(netdev, wxhw->mac.perm_addr);
+	ngbe_mac_set_default_filter(adapter, wxhw->mac.perm_addr);
+
+	err = register_netdev(netdev);
+	if (err)
+		goto err_register;
+
 	pci_set_drvdata(pdev, adapter);
 
+	netif_info(adapter, probe, netdev,
+		   "PHY: %s, PBA No: Wang Xun GbE Family Controller\n",
+		   hw->phy.type == ngbe_phy_internal ? "Internal" : "External");
+	netif_info(adapter, probe, netdev, "%pM\n", netdev->dev_addr);
+
 	return 0;
 
+err_register:
+	wx_control_hw(wxhw, false);
+err_free_mac_table:
+	kfree(adapter->mac_table);
 err_pci_release_regions:
 	pci_disable_pcie_error_reporting(pdev);
 	pci_release_selected_regions(pdev,
@@ -146,9 +508,15 @@ static int ngbe_probe(struct pci_dev *pdev,
  **/
 static void ngbe_remove(struct pci_dev *pdev)
 {
+	struct ngbe_adapter *adapter = pci_get_drvdata(pdev);
+	struct net_device *netdev;
+
+	netdev = adapter->netdev;
+	unregister_netdev(netdev);
 	pci_release_selected_regions(pdev,
 				     pci_select_bars(pdev, IORESOURCE_MEM));
 
+	kfree(adapter->mac_table);
 	pci_disable_pcie_error_reporting(pdev);
 
 	pci_disable_device(pdev);

drivers/net/ethernet/wangxun/ngbe/ngbe_type.h

@@ -8,11 +8,6 @@
 #include <linux/netdevice.h>
 
 /************ NGBE_register.h ************/
-/* Vendor ID */
-#ifndef PCI_VENDOR_ID_WANGXUN
-#define PCI_VENDOR_ID_WANGXUN			0x8088
-#endif
-
 /* Device IDs */
 #define NGBE_DEV_ID_EM_WX1860AL_W		0x0100
 #define NGBE_DEV_ID_EM_WX1860A2			0x0101
@@ -47,4 +42,98 @@
 #define NGBE_WOL_SUP				0x4000
 #define NGBE_WOL_MASK				0x4000
 
+/**************** EM Registers ****************************/
+/* chip control Registers */
+#define NGBE_MIS_PRB_CTL			0x10010
+/* FMGR Registers */
+#define NGBE_SPI_ILDR_STATUS			0x10120
+#define NGBE_SPI_ILDR_STATUS_PERST		BIT(0) /* PCIE_PERST is done */
+#define NGBE_SPI_ILDR_STATUS_PWRRST		BIT(1) /* Power on reset is done */
+#define NGBE_SPI_ILDR_STATUS_LAN_SW_RST(_i)	BIT((_i) + 9) /* lan soft reset done */
+
+/* Checksum and EEPROM pointers */
+#define NGBE_CALSUM_COMMAND			0xE9
+#define NGBE_CALSUM_CAP_STATUS			0x10224
+#define NGBE_EEPROM_VERSION_STORE_REG		0x1022C
+#define NGBE_SAN_MAC_ADDR_PTR			0x18
+#define NGBE_DEVICE_CAPS			0x1C
+#define NGBE_EEPROM_VERSION_L			0x1D
+#define NGBE_EEPROM_VERSION_H			0x1E
+
+/* Media-dependent registers. */
+#define NGBE_MDIO_CLAUSE_SELECT			0x11220
+
+/* GPIO Registers */
+#define NGBE_GPIO_DR				0x14800
+#define NGBE_GPIO_DDR				0x14804
+/*GPIO bit */
+#define NGBE_GPIO_DR_0				BIT(0) /* SDP0 Data Value */
+#define NGBE_GPIO_DR_1				BIT(1) /* SDP1 Data Value */
+#define NGBE_GPIO_DDR_0				BIT(0) /* SDP0 IO direction */
+#define NGBE_GPIO_DDR_1				BIT(1) /* SDP1 IO direction */
+
+/* Wake up registers */
+#define NGBE_PSR_WKUP_CTL			0x15B80
+/* Wake Up Filter Control Bit */
+#define NGBE_PSR_WKUP_CTL_LNKC			BIT(0) /* Link Status Change Wakeup Enable*/
+#define NGBE_PSR_WKUP_CTL_MAG			BIT(1) /* Magic Packet Wakeup Enable */
+#define NGBE_PSR_WKUP_CTL_EX			BIT(2) /* Directed Exact Wakeup Enable */
+#define NGBE_PSR_WKUP_CTL_MC			BIT(3) /* Directed Multicast Wakeup Enable*/
+#define NGBE_PSR_WKUP_CTL_BC			BIT(4) /* Broadcast Wakeup Enable */
+#define NGBE_PSR_WKUP_CTL_ARP			BIT(5) /* ARP Request Packet Wakeup Enable*/
+#define NGBE_PSR_WKUP_CTL_IPV4			BIT(6) /* Directed IPv4 Pkt Wakeup Enable */
+#define NGBE_PSR_WKUP_CTL_IPV6			BIT(7) /* Directed IPv6 Pkt Wakeup Enable */
+
+#define NGBE_FW_EEPROM_CHECKSUM_CMD		0xE9
+#define NGBE_FW_NVM_DATA_OFFSET			3
+#define NGBE_FW_CMD_DEFAULT_CHECKSUM		0xFF /* checksum always 0xFF */
+#define NGBE_FW_CMD_ST_PASS			0x80658383
+#define NGBE_FW_CMD_ST_FAIL			0x70657376
+
+enum ngbe_phy_type {
+	ngbe_phy_unknown = 0,
+	ngbe_phy_none,
+	ngbe_phy_internal,
+	ngbe_phy_m88e1512,
+	ngbe_phy_m88e1512_sfi,
+	ngbe_phy_m88e1512_unknown,
+	ngbe_phy_yt8521s,
+	ngbe_phy_yt8521s_sfi,
+	ngbe_phy_internal_yt8521s_sfi,
+	ngbe_phy_generic
+};
+
+enum ngbe_media_type {
+	ngbe_media_type_unknown = 0,
+	ngbe_media_type_fiber,
+	ngbe_media_type_copper,
+	ngbe_media_type_backplane,
+};
+
+enum ngbe_mac_type {
+	ngbe_mac_type_unknown = 0,
+	ngbe_mac_type_mdi,
+	ngbe_mac_type_rgmii
+};
+
+struct ngbe_phy_info {
+	enum ngbe_phy_type type;
+	enum ngbe_media_type media_type;
+
+	u32 addr;
+	u32 id;
+
+	bool reset_if_overtemp;
+
+};
+
+struct ngbe_hw {
+	struct wx_hw wxhw;
+	struct ngbe_phy_info phy;
+	enum ngbe_mac_type mac_type;
+
+	bool wol_enabled;
+	bool ncsi_enabled;
+	bool gpio_ctrl;
+};
 #endif /* _NGBE_TYPE_H_ */

drivers/net/ethernet/wangxun/txgbe/txgbe.h

@@ -35,6 +35,7 @@ struct txgbe_adapter {
 	struct txgbe_hw hw;
 	u16 msg_enable;
 	struct txgbe_mac_addr *mac_table;
+	char eeprom_id[32];
 };
 
 extern char txgbe_driver_name[];

drivers/net/ethernet/wangxun/txgbe/txgbe_hw.c

@@ -44,6 +44,218 @@ static void txgbe_init_thermal_sensor_thresh(struct txgbe_hw *hw)
 	wr32(wxhw, WX_TS_DALARM_THRE, 614);
 }
 
+/**
+ *  txgbe_read_pba_string - Reads part number string from EEPROM
+ *  @hw: pointer to hardware structure
+ *  @pba_num: stores the part number string from the EEPROM
+ *  @pba_num_size: part number string buffer length
+ *
+ *  Reads the part number string from the EEPROM.
+ **/
+int txgbe_read_pba_string(struct txgbe_hw *hw, u8 *pba_num, u32 pba_num_size)
+{
+	u16 pba_ptr, offset, length, data;
+	struct wx_hw *wxhw = &hw->wxhw;
+	int ret_val;
+
+	if (!pba_num) {
+		wx_err(wxhw, "PBA string buffer was null\n");
+		return -EINVAL;
+	}
+
+	ret_val = wx_read_ee_hostif(wxhw,
+				    wxhw->eeprom.sw_region_offset + TXGBE_PBANUM0_PTR,
+				    &data);
+	if (ret_val != 0) {
+		wx_err(wxhw, "NVM Read Error\n");
+		return ret_val;
+	}
+
+	ret_val = wx_read_ee_hostif(wxhw,
+				    wxhw->eeprom.sw_region_offset + TXGBE_PBANUM1_PTR,
+				    &pba_ptr);
+	if (ret_val != 0) {
+		wx_err(wxhw, "NVM Read Error\n");
+		return ret_val;
+	}
+
+	/* if data is not ptr guard the PBA must be in legacy format which
+	 * means pba_ptr is actually our second data word for the PBA number
+	 * and we can decode it into an ascii string
+	 */
+	if (data != TXGBE_PBANUM_PTR_GUARD) {
+		wx_err(wxhw, "NVM PBA number is not stored as string\n");
+
+		/* we will need 11 characters to store the PBA */
+		if (pba_num_size < 11) {
+			wx_err(wxhw, "PBA string buffer too small\n");
+			return -ENOMEM;
+		}
+
+		/* extract hex string from data and pba_ptr */
+		pba_num[0] = (data >> 12) & 0xF;
+		pba_num[1] = (data >> 8) & 0xF;
+		pba_num[2] = (data >> 4) & 0xF;
+		pba_num[3] = data & 0xF;
+		pba_num[4] = (pba_ptr >> 12) & 0xF;
+		pba_num[5] = (pba_ptr >> 8) & 0xF;
+		pba_num[6] = '-';
+		pba_num[7] = 0;
+		pba_num[8] = (pba_ptr >> 4) & 0xF;
+		pba_num[9] = pba_ptr & 0xF;
+
+		/* put a null character on the end of our string */
+		pba_num[10] = '\0';
+
+		/* switch all the data but the '-' to hex char */
+		for (offset = 0; offset < 10; offset++) {
+			if (pba_num[offset] < 0xA)
+				pba_num[offset] += '0';
+			else if (pba_num[offset] < 0x10)
+				pba_num[offset] += 'A' - 0xA;
+		}
+
+		return 0;
+	}
+
+	ret_val = wx_read_ee_hostif(wxhw, pba_ptr, &length);
+	if (ret_val != 0) {
+		wx_err(wxhw, "NVM Read Error\n");
+		return ret_val;
+	}
+
+	if (length == 0xFFFF || length == 0) {
+		wx_err(wxhw, "NVM PBA number section invalid length\n");
+		return -EINVAL;
+	}
+
+	/* check if pba_num buffer is big enough */
+	if (pba_num_size  < (((u32)length * 2) - 1)) {
+		wx_err(wxhw, "PBA string buffer too small\n");
+		return -ENOMEM;
+	}
+
+	/* trim pba length from start of string */
+	pba_ptr++;
+	length--;
+
+	for (offset = 0; offset < length; offset++) {
+		ret_val = wx_read_ee_hostif(wxhw, pba_ptr + offset, &data);
+		if (ret_val != 0) {
+			wx_err(wxhw, "NVM Read Error\n");
+			return ret_val;
+		}
+		pba_num[offset * 2] = (u8)(data >> 8);
+		pba_num[(offset * 2) + 1] = (u8)(data & 0xFF);
+	}
+	pba_num[offset * 2] = '\0';
+
+	return 0;
+}
+
+/**
+ *  txgbe_calc_eeprom_checksum - Calculates and returns the checksum
+ *  @hw: pointer to hardware structure
+ *  @checksum: pointer to cheksum
+ *
+ *  Returns a negative error code on error
+ **/
+static int txgbe_calc_eeprom_checksum(struct txgbe_hw *hw, u16 *checksum)
+{
+	struct wx_hw *wxhw = &hw->wxhw;
+	u16 *eeprom_ptrs = NULL;
+	u32 buffer_size = 0;
+	u16 *buffer = NULL;
+	u16 *local_buffer;
+	int status;
+	u16 i;
+
+	wx_init_eeprom_params(wxhw);
+
+	if (!buffer) {
+		eeprom_ptrs = kvmalloc_array(TXGBE_EEPROM_LAST_WORD, sizeof(u16),
+					     GFP_KERNEL);
+		if (!eeprom_ptrs)
+			return -ENOMEM;
+		/* Read pointer area */
+		status = wx_read_ee_hostif_buffer(wxhw, 0,
+						  TXGBE_EEPROM_LAST_WORD,
+						  eeprom_ptrs);
+		if (status != 0) {
+			wx_err(wxhw, "Failed to read EEPROM image\n");
+			return status;
+		}
+		local_buffer = eeprom_ptrs;
+	} else {
+		if (buffer_size < TXGBE_EEPROM_LAST_WORD)
+			return -EFAULT;
+		local_buffer = buffer;
+	}
+
+	for (i = 0; i < TXGBE_EEPROM_LAST_WORD; i++)
+		if (i != wxhw->eeprom.sw_region_offset + TXGBE_EEPROM_CHECKSUM)
+			*checksum += local_buffer[i];
+
+	*checksum = TXGBE_EEPROM_SUM - *checksum;
+	if (*checksum < 0)
+		return -EINVAL;
+
+	if (eeprom_ptrs)
+		kvfree(eeprom_ptrs);
+
+	return 0;
+}
+
+/**
+ *  txgbe_validate_eeprom_checksum - Validate EEPROM checksum
+ *  @hw: pointer to hardware structure
+ *  @checksum_val: calculated checksum
+ *
+ *  Performs checksum calculation and validates the EEPROM checksum.  If the
+ *  caller does not need checksum_val, the value can be NULL.
+ **/
+int txgbe_validate_eeprom_checksum(struct txgbe_hw *hw, u16 *checksum_val)
+{
+	struct wx_hw *wxhw = &hw->wxhw;
+	u16 read_checksum = 0;
+	u16 checksum;
+	int status;
+
+	/* Read the first word from the EEPROM. If this times out or fails, do
+	 * not continue or we could be in for a very long wait while every
+	 * EEPROM read fails
+	 */
+	status = wx_read_ee_hostif(wxhw, 0, &checksum);
+	if (status) {
+		wx_err(wxhw, "EEPROM read failed\n");
+		return status;
+	}
+
+	checksum = 0;
+	status = txgbe_calc_eeprom_checksum(hw, &checksum);
+	if (status != 0)
+		return status;
+
+	status = wx_read_ee_hostif(wxhw, wxhw->eeprom.sw_region_offset +
+				   TXGBE_EEPROM_CHECKSUM, &read_checksum);
+	if (status != 0)
+		return status;
+
+	/* Verify read checksum from EEPROM is the same as
+	 * calculated checksum
+	 */
+	if (read_checksum != checksum) {
+		status = -EIO;
+		wx_err(wxhw, "Invalid EEPROM checksum\n");
+	}
+
+	/* If the user cares, return the calculated checksum */
+	if (checksum_val)
+		*checksum_val = checksum;
+
+	return status;
+}
+
 static void txgbe_reset_misc(struct txgbe_hw *hw)
 {
 	struct wx_hw *wxhw = &hw->wxhw;
@@ -63,7 +275,6 @@ static void txgbe_reset_misc(struct txgbe_hw *hw)
 int txgbe_reset_hw(struct txgbe_hw *hw)
 {
 	struct wx_hw *wxhw = &hw->wxhw;
-	u32 reset = 0;
 	int status;
 
 	/* Call adapter stop to disable tx/rx and clear interrupts */
@@ -71,10 +282,10 @@ int txgbe_reset_hw(struct txgbe_hw *hw)
 	if (status != 0)
 		return status;
 
-	reset = WX_MIS_RST_LAN_RST(wxhw->bus.func);
-	wr32(wxhw, WX_MIS_RST, reset | rd32(wxhw, WX_MIS_RST));
+	if (!(((wxhw->subsystem_device_id & WX_NCSI_MASK) == WX_NCSI_SUP) ||
+	      ((wxhw->subsystem_device_id & WX_WOL_MASK) == WX_WOL_SUP)))
+		wx_reset_hostif(wxhw);
 
-	WX_WRITE_FLUSH(wxhw);
 	usleep_range(10, 100);
 
 	status = wx_check_flash_load(wxhw, TXGBE_SPI_ILDR_STATUS_LAN_SW_RST(wxhw->bus.func));

drivers/net/ethernet/wangxun/txgbe/txgbe_hw.h

@@ -4,6 +4,8 @@
 #ifndef _TXGBE_HW_H_
 #define _TXGBE_HW_H_
 
+int txgbe_read_pba_string(struct txgbe_hw *hw, u8 *pba_num, u32 pba_num_size);
+int txgbe_validate_eeprom_checksum(struct txgbe_hw *hw, u16 *checksum_val);
 int txgbe_reset_hw(struct txgbe_hw *hw);
 
 #endif /* _TXGBE_HW_H_ */

drivers/net/ethernet/wangxun/txgbe/txgbe_main.c

@@ -158,6 +158,14 @@ static int txgbe_del_mac_filter(struct txgbe_adapter *adapter, u8 *addr, u16 poo
 	return -ENOMEM;
 }
 
+static void txgbe_up_complete(struct txgbe_adapter *adapter)
+{
+	struct txgbe_hw *hw = &adapter->hw;
+	struct wx_hw *wxhw = &hw->wxhw;
+
+	wx_control_hw(wxhw, true);
+}
+
 static void txgbe_reset(struct txgbe_adapter *adapter)
 {
 	struct net_device *netdev = adapter->netdev;
@@ -270,6 +278,10 @@ static int txgbe_sw_init(struct txgbe_adapter *adapter)
  **/
 static int txgbe_open(struct net_device *netdev)
 {
+	struct txgbe_adapter *adapter = netdev_priv(netdev);
+
+	txgbe_up_complete(adapter);
+
 	return 0;
 }
 
@@ -301,6 +313,7 @@ static int txgbe_close(struct net_device *netdev)
 	struct txgbe_adapter *adapter = netdev_priv(netdev);
 
 	txgbe_down(adapter);
+	wx_control_hw(&adapter->hw.wxhw, false);
 
 	return 0;
 }
@@ -309,6 +322,8 @@ static void txgbe_dev_shutdown(struct pci_dev *pdev, bool *enable_wake)
 {
 	struct txgbe_adapter *adapter = pci_get_drvdata(pdev);
 	struct net_device *netdev = adapter->netdev;
+	struct txgbe_hw *hw = &adapter->hw;
+	struct wx_hw *wxhw = &hw->wxhw;
 
 	netif_device_detach(netdev);
 
@@ -317,6 +332,8 @@ static void txgbe_dev_shutdown(struct pci_dev *pdev, bool *enable_wake)
 		txgbe_close_suspend(adapter);
 	rtnl_unlock();
 
+	wx_control_hw(wxhw, false);
+
 	pci_disable_device(pdev);
 }
 
@@ -393,6 +410,12 @@ static int txgbe_probe(struct pci_dev *pdev,
 	struct net_device *netdev;
 	int err, expected_gts;
 
+	u16 eeprom_verh = 0, eeprom_verl = 0, offset = 0;
+	u16 eeprom_cfg_blkh = 0, eeprom_cfg_blkl = 0;
+	u16 build = 0, major = 0, patch = 0;
+	u8 part_str[TXGBE_PBANUM_LENGTH];
+	u32 etrack_id = 0;
+
 	err = pci_enable_device_mem(pdev);
 	if (err)
 		return err;
@@ -457,6 +480,12 @@ static int txgbe_probe(struct pci_dev *pdev,
 	if (err)
 		goto err_free_mac_table;
 
+	err = wx_mng_present(wxhw);
+	if (err) {
+		dev_err(&pdev->dev, "Management capability is not present\n");
+		goto err_free_mac_table;
+	}
+
 	err = txgbe_reset_hw(hw);
 	if (err) {
 		dev_err(&pdev->dev, "HW Init failed: %d\n", err);
@@ -465,12 +494,59 @@ static int txgbe_probe(struct pci_dev *pdev,
 
 	netdev->features |= NETIF_F_HIGHDMA;
 
+	/* make sure the EEPROM is good */
+	err = txgbe_validate_eeprom_checksum(hw, NULL);
+	if (err != 0) {
+		dev_err(&pdev->dev, "The EEPROM Checksum Is Not Valid\n");
+		wr32(wxhw, WX_MIS_RST, WX_MIS_RST_SW_RST);
+		err = -EIO;
+		goto err_free_mac_table;
+	}
+
 	eth_hw_addr_set(netdev, wxhw->mac.perm_addr);
 	txgbe_mac_set_default_filter(adapter, wxhw->mac.perm_addr);
 
+	/* Save off EEPROM version number and Option Rom version which
+	 * together make a unique identify for the eeprom
+	 */
+	wx_read_ee_hostif(wxhw,
+			  wxhw->eeprom.sw_region_offset + TXGBE_EEPROM_VERSION_H,
+			  &eeprom_verh);
+	wx_read_ee_hostif(wxhw,
+			  wxhw->eeprom.sw_region_offset + TXGBE_EEPROM_VERSION_L,
+			  &eeprom_verl);
+	etrack_id = (eeprom_verh << 16) | eeprom_verl;
+
+	wx_read_ee_hostif(wxhw,
+			  wxhw->eeprom.sw_region_offset + TXGBE_ISCSI_BOOT_CONFIG,
+			  &offset);
+
+	/* Make sure offset to SCSI block is valid */
+	if (!(offset == 0x0) && !(offset == 0xffff)) {
+		wx_read_ee_hostif(wxhw, offset + 0x84, &eeprom_cfg_blkh);
+		wx_read_ee_hostif(wxhw, offset + 0x83, &eeprom_cfg_blkl);
+
+		/* Only display Option Rom if exist */
+		if (eeprom_cfg_blkl && eeprom_cfg_blkh) {
+			major = eeprom_cfg_blkl >> 8;
+			build = (eeprom_cfg_blkl << 8) | (eeprom_cfg_blkh >> 8);
+			patch = eeprom_cfg_blkh & 0x00ff;
+
+			snprintf(adapter->eeprom_id, sizeof(adapter->eeprom_id),
+				 "0x%08x, %d.%d.%d", etrack_id, major, build,
+				 patch);
+		} else {
+			snprintf(adapter->eeprom_id, sizeof(adapter->eeprom_id),
+				 "0x%08x", etrack_id);
+		}
+	} else {
+		snprintf(adapter->eeprom_id, sizeof(adapter->eeprom_id),
+			 "0x%08x", etrack_id);
+	}
+
 	err = register_netdev(netdev);
 	if (err)
-		goto err_free_mac_table;
+		goto err_release_hw;
 
 	pci_set_drvdata(pdev, adapter);
 
@@ -488,10 +564,17 @@ static int txgbe_probe(struct pci_dev *pdev,
 	else
 		dev_warn(&pdev->dev, "Failed to enumerate PF devices.\n");
 
+	/* First try to read PBA as a string */
+	err = txgbe_read_pba_string(hw, part_str, TXGBE_PBANUM_LENGTH);
+	if (err)
+		strncpy(part_str, "Unknown", TXGBE_PBANUM_LENGTH);
+
 	netif_info(adapter, probe, netdev, "%pM\n", netdev->dev_addr);
 
 	return 0;
 
+err_release_hw:
+	wx_control_hw(wxhw, false);
 err_free_mac_table:
 	kfree(adapter->mac_table);
 err_pci_release_regions:

drivers/net/ethernet/wangxun/txgbe/txgbe_type.h

@@ -53,6 +53,20 @@
 #define TXGBE_TS_CTL                            0x10300
 #define TXGBE_TS_CTL_EVAL_MD                    BIT(31)
 
+/* Part Number String Length */
+#define TXGBE_PBANUM_LENGTH                     32
+
+/* Checksum and EEPROM pointers */
+#define TXGBE_EEPROM_LAST_WORD                  0x800
+#define TXGBE_EEPROM_CHECKSUM                   0x2F
+#define TXGBE_EEPROM_SUM                        0xBABA
+#define TXGBE_EEPROM_VERSION_L                  0x1D
+#define TXGBE_EEPROM_VERSION_H                  0x1E
+#define TXGBE_ISCSI_BOOT_CONFIG                 0x07
+#define TXGBE_PBANUM0_PTR                       0x05
+#define TXGBE_PBANUM1_PTR                       0x06
+#define TXGBE_PBANUM_PTR_GUARD                  0xFAFA
+
 struct txgbe_hw {
 	struct wx_hw wxhw;
 };