Merge tag 'phy-for-4.3' of...

Merge tag 'phy-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next

Kishon writes:

phy: for 4.3

*) Add new NXP USB OTG PHY driver
*) Add vbus/id detection, extcon support and fixes in phy-sun4i-usb
   driver
*) Add support to use phy-sun4i-usb driver for sun8i-a23 and sun8i-a33
   SoCs
*) Other trivial code cleanups, dropping .owner assignment and constify
   phy_ops
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Documentation/devicetree/bindings/phy/phy-lpc18xx-usb-otg.txt

+NXP LPC18xx/43xx internal USB OTG PHY binding
+---------------------------------------------
+
+This file contains documentation for the internal USB OTG PHY found
+in NXP LPC18xx and LPC43xx SoCs.
+
+Required properties:
+- compatible	: must be "nxp,lpc1850-usb-otg-phy"
+- clocks	: must be exactly one entry
+See: Documentation/devicetree/bindings/clock/clock-bindings.txt
+- #phy-cells	: must be 0 for this phy
+See: Documentation/devicetree/bindings/phy/phy-bindings.txt
+
+The phy node must be a child of the creg syscon node.
+
+Example:
+creg: syscon@40043000 {
+	compatible = "nxp,lpc1850-creg", "syscon", "simple-mfd";
+	reg = <0x40043000 0x1000>;
+
+	usb0_otg_phy: phy@004 {
+		compatible = "nxp,lpc1850-usb-otg-phy";
+		clocks = <&ccu1 CLK_USB0>;
+		#phy-cells = <0>;
+	};
+};

Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt

@@ -7,6 +7,8 @@ Required properties:
   * allwinner,sun5i-a13-usb-phy
   * allwinner,sun6i-a31-usb-phy
   * allwinner,sun7i-a20-usb-phy
+  * allwinner,sun8i-a23-usb-phy
+  * allwinner,sun8i-a33-usb-phy
 - reg : a list of offset + length pairs
 - reg-names :
   * "phy_ctrl"
@@ -17,12 +19,21 @@ Required properties:
 - clock-names :
   * "usb_phy" for sun4i, sun5i or sun7i
   * "usb0_phy", "usb1_phy" and "usb2_phy" for sun6i
+  * "usb0_phy", "usb1_phy" for sun8i
 - resets : a list of phandle + reset specifier pairs
 - reset-names :
   * "usb0_reset"
   * "usb1_reset"
   * "usb2_reset" for sun4i, sun6i or sun7i
 
+Optional properties:
+- usb0_id_det-gpios : gpio phandle for reading the otg id pin value
+- usb0_vbus_det-gpios : gpio phandle for detecting the presence of usb0 vbus
+- usb0_vbus_power-supply: power-supply phandle for usb0 vbus presence detect
+- usb0_vbus-supply : regulator phandle for controller usb0 vbus
+- usb1_vbus-supply : regulator phandle for controller usb1 vbus
+- usb2_vbus-supply : regulator phandle for controller usb2 vbus
+
 Example:
 	usbphy: phy@0x01c13400 {
 		#phy-cells = <1>;
@@ -32,6 +43,13 @@ Example:
 		reg-names = "phy_ctrl", "pmu1", "pmu2";
 		clocks = <&usb_clk 8>;
 		clock-names = "usb_phy";
-		resets = <&usb_clk 1>, <&usb_clk 2>;
-		reset-names = "usb1_reset", "usb2_reset";
+		resets = <&usb_clk 0>, <&usb_clk 1>, <&usb_clk 2>;
+		reset-names = "usb0_reset", "usb1_reset", "usb2_reset";
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
+		usb0_id_det-gpios = <&pio 7 19 GPIO_ACTIVE_HIGH>; /* PH19 */
+		usb0_vbus_det-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */
+		usb0_vbus-supply = <&reg_usb0_vbus>;
+		usb1_vbus-supply = <&reg_usb1_vbus>;
+		usb2_vbus-supply = <&reg_usb2_vbus>;
 	};

drivers/phy/Kconfig

@@ -54,6 +54,17 @@ config PHY_EXYNOS_MIPI_VIDEO
 	  Support for MIPI CSI-2 and MIPI DSI DPHY found on Samsung S5P
 	  and EXYNOS SoCs.
 
+config PHY_LPC18XX_USB_OTG
+	tristate "NXP LPC18xx/43xx SoC USB OTG PHY driver"
+	depends on OF && (ARCH_LPC18XX || COMPILE_TEST)
+	depends on MFD_SYSCON
+	select GENERIC_PHY
+	help
+	  Enable this to support NXP LPC18xx/43xx internal USB OTG PHY.
+
+	  This driver is need for USB0 support on LPC18xx/43xx and takes
+	  care of enabling and clock setup.
+
 config PHY_PXA_28NM_HSIC
 	tristate "Marvell USB HSIC 28nm PHY Driver"
 	depends on HAS_IOMEM
@@ -199,6 +210,8 @@ config PHY_SUN4I_USB
 	tristate "Allwinner sunxi SoC USB PHY driver"
 	depends on ARCH_SUNXI && HAS_IOMEM && OF
 	depends on RESET_CONTROLLER
+	depends on EXTCON
+	depends on POWER_SUPPLY
 	select GENERIC_PHY
 	help
 	  Enable this to support the transceiver that is part of Allwinner

drivers/phy/Makefile

@@ -10,6 +10,7 @@ obj-$(CONFIG_ARMADA375_USBCLUSTER_PHY)	+= phy-armada375-usb2.o
 obj-$(CONFIG_BCM_KONA_USB2_PHY)		+= phy-bcm-kona-usb2.o
 obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO)	+= phy-exynos-dp-video.o
 obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO)	+= phy-exynos-mipi-video.o
+obj-$(CONFIG_PHY_LPC18XX_USB_OTG)	+= phy-lpc18xx-usb-otg.o
 obj-$(CONFIG_PHY_PXA_28NM_USB2)		+= phy-pxa-28nm-usb2.o
 obj-$(CONFIG_PHY_PXA_28NM_HSIC)		+= phy-pxa-28nm-hsic.o
 obj-$(CONFIG_PHY_MVEBU_SATA)		+= phy-mvebu-sata.o

drivers/phy/phy-armada375-usb2.c

@@ -51,7 +51,7 @@ static int armada375_usb_phy_init(struct phy *phy)
 	return 0;
 }
 
-static struct phy_ops armada375_usb_phy_ops = {
+static const struct phy_ops armada375_usb_phy_ops = {
 	.init = armada375_usb_phy_init,
 	.owner = THIS_MODULE,
 };
@@ -149,7 +149,6 @@ static struct platform_driver armada375_usb_phy_driver = {
 	.driver = {
 		.of_match_table	= of_usb_cluster_table,
 		.name  = "armada-375-usb-cluster",
-		.owner = THIS_MODULE,
 	}
 };
 module_platform_driver(armada375_usb_phy_driver);

drivers/phy/phy-bcm-kona-usb2.c

@@ -91,7 +91,7 @@ static int bcm_kona_usb_phy_power_off(struct phy *gphy)
 	return 0;
 }
 
-static struct phy_ops ops = {
+static const struct phy_ops ops = {
 	.init		= bcm_kona_usb_phy_init,
 	.power_on	= bcm_kona_usb_phy_power_on,
 	.power_off	= bcm_kona_usb_phy_power_off,

drivers/phy/phy-berlin-sata.c

@@ -176,7 +176,7 @@ static struct phy *phy_berlin_sata_phy_xlate(struct device *dev,
 	return priv->phys[i]->phy;
 }
 
-static struct phy_ops phy_berlin_sata_ops = {
+static const struct phy_ops phy_berlin_sata_ops = {
 	.power_on	= phy_berlin_sata_power_on,
 	.power_off	= phy_berlin_sata_power_off,
 	.owner		= THIS_MODULE,

drivers/phy/phy-berlin-usb.c

@@ -147,12 +147,12 @@ static int phy_berlin_usb_power_on(struct phy *phy)
 	return 0;
 }
 
-static struct phy_ops phy_berlin_usb_ops = {
+static const struct phy_ops phy_berlin_usb_ops = {
 	.power_on	= phy_berlin_usb_power_on,
 	.owner		= THIS_MODULE,
 };
 
-static const struct of_device_id phy_berlin_sata_of_match[] = {
+static const struct of_device_id phy_berlin_usb_of_match[] = {
 	{
 		.compatible = "marvell,berlin2-usb-phy",
 		.data = &phy_berlin_pll_dividers[0],
@@ -163,12 +163,12 @@ static const struct of_device_id phy_berlin_sata_of_match[] = {
 	},
 	{ },
 };
-MODULE_DEVICE_TABLE(of, phy_berlin_sata_of_match);
+MODULE_DEVICE_TABLE(of, phy_berlin_usb_of_match);
 
 static int phy_berlin_usb_probe(struct platform_device *pdev)
 {
 	const struct of_device_id *match =
-		of_match_device(phy_berlin_sata_of_match, &pdev->dev);
+		of_match_device(phy_berlin_usb_of_match, &pdev->dev);
 	struct phy_berlin_usb_priv *priv;
 	struct resource *res;
 	struct phy *phy;
@@ -207,8 +207,7 @@ static struct platform_driver phy_berlin_usb_driver = {
 	.probe	= phy_berlin_usb_probe,
 	.driver	= {
 		.name		= "phy-berlin-usb",
-		.owner		= THIS_MODULE,
-		.of_match_table	= phy_berlin_sata_of_match,
+		.of_match_table	= phy_berlin_usb_of_match,
 	},
 };
 module_platform_driver(phy_berlin_usb_driver);

drivers/phy/phy-brcmstb-sata.c

@@ -122,7 +122,7 @@ static int brcm_sata_phy_init(struct phy *phy)
 	return 0;
 }
 
-static struct phy_ops phy_ops_28nm = {
+static const struct phy_ops phy_ops_28nm = {
 	.init		= brcm_sata_phy_init,
 	.owner		= THIS_MODULE,
 };

drivers/phy/phy-dm816x-usb.c

@@ -113,7 +113,7 @@ static int dm816x_usb_phy_init(struct phy *x)
 	return 0;
 }
 
-static struct phy_ops ops = {
+static const struct phy_ops ops = {
 	.init		= dm816x_usb_phy_init,
 	.owner		= THIS_MODULE,
 };

drivers/phy/phy-exynos-dp-video.c

@@ -48,7 +48,7 @@ static int exynos_dp_video_phy_power_off(struct phy *phy)
 				  EXYNOS5_PHY_ENABLE, 0);
 }
 
-static struct phy_ops exynos_dp_video_phy_ops = {
+static const struct phy_ops exynos_dp_video_phy_ops = {
 	.power_on	= exynos_dp_video_phy_power_on,
 	.power_off	= exynos_dp_video_phy_power_off,
 	.owner		= THIS_MODULE,

drivers/phy/phy-exynos-mipi-video.c

@@ -124,7 +124,7 @@ static struct phy *exynos_mipi_video_phy_xlate(struct device *dev,
 	return state->phys[args->args[0]].phy;
 }
 
-static struct phy_ops exynos_mipi_video_phy_ops = {
+static const struct phy_ops exynos_mipi_video_phy_ops = {
 	.power_on	= exynos_mipi_video_phy_power_on,
 	.power_off	= exynos_mipi_video_phy_power_off,
 	.owner		= THIS_MODULE,

drivers/phy/phy-exynos5-usbdrd.c

@@ -537,7 +537,7 @@ static struct phy *exynos5_usbdrd_phy_xlate(struct device *dev,
 	return phy_drd->phys[args->args[0]].phy;
 }
 
-static struct phy_ops exynos5_usbdrd_phy_ops = {
+static const struct phy_ops exynos5_usbdrd_phy_ops = {
 	.init		= exynos5_usbdrd_phy_init,
 	.exit		= exynos5_usbdrd_phy_exit,
 	.power_on	= exynos5_usbdrd_phy_power_on,

drivers/phy/phy-exynos5250-sata.c

@@ -154,7 +154,7 @@ static int exynos_sata_phy_init(struct phy *phy)
 	return ret;
 }
 
-static struct phy_ops exynos_sata_phy_ops = {
+static const struct phy_ops exynos_sata_phy_ops = {
 	.init		= exynos_sata_phy_init,
 	.power_on	= exynos_sata_phy_power_on,
 	.power_off	= exynos_sata_phy_power_off,

drivers/phy/phy-hix5hd2-sata.c

@@ -129,7 +129,7 @@ static int hix5hd2_sata_phy_init(struct phy *phy)
 	return 0;
 }
 
-static struct phy_ops hix5hd2_sata_phy_ops = {
+static const struct phy_ops hix5hd2_sata_phy_ops = {
 	.init		= hix5hd2_sata_phy_init,
 	.owner		= THIS_MODULE,
 };

drivers/phy/phy-lpc18xx-usb-otg.c

+/*
+ * PHY driver for NXP LPC18xx/43xx internal USB OTG PHY
+ *
+ * Copyright (C) 2015 Joachim Eastwood <manabian@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+/* USB OTG PHY register offset and bit in CREG */
+#define LPC18XX_CREG_CREG0		0x004
+#define LPC18XX_CREG_CREG0_USB0PHY	BIT(5)
+
+struct lpc18xx_usb_otg_phy {
+	struct phy *phy;
+	struct clk *clk;
+	struct regmap *reg;
+};
+
+static int lpc18xx_usb_otg_phy_init(struct phy *phy)
+{
+	struct lpc18xx_usb_otg_phy *lpc = phy_get_drvdata(phy);
+	int ret;
+
+	/* The PHY must be clocked at 480 MHz */
+	ret = clk_set_rate(lpc->clk, 480000000);
+	if (ret)
+		return ret;
+
+	return clk_prepare(lpc->clk);
+}
+
+static int lpc18xx_usb_otg_phy_exit(struct phy *phy)
+{
+	struct lpc18xx_usb_otg_phy *lpc = phy_get_drvdata(phy);
+
+	clk_unprepare(lpc->clk);
+
+	return 0;
+}
+
+static int lpc18xx_usb_otg_phy_power_on(struct phy *phy)
+{
+	struct lpc18xx_usb_otg_phy *lpc = phy_get_drvdata(phy);
+	int ret;
+
+	ret = clk_enable(lpc->clk);
+	if (ret)
+		return ret;
+
+	/* The bit in CREG is cleared to enable the PHY */
+	return regmap_update_bits(lpc->reg, LPC18XX_CREG_CREG0,
+				  LPC18XX_CREG_CREG0_USB0PHY, 0);
+}
+
+static int lpc18xx_usb_otg_phy_power_off(struct phy *phy)
+{
+	struct lpc18xx_usb_otg_phy *lpc = phy_get_drvdata(phy);
+	int ret;
+
+	ret = regmap_update_bits(lpc->reg, LPC18XX_CREG_CREG0,
+				 LPC18XX_CREG_CREG0_USB0PHY,
+				 LPC18XX_CREG_CREG0_USB0PHY);
+	if (ret)
+		return ret;
+
+	clk_disable(lpc->clk);
+
+	return 0;
+}
+
+static const struct phy_ops lpc18xx_usb_otg_phy_ops = {
+	.init		= lpc18xx_usb_otg_phy_init,
+	.exit		= lpc18xx_usb_otg_phy_exit,
+	.power_on	= lpc18xx_usb_otg_phy_power_on,
+	.power_off	= lpc18xx_usb_otg_phy_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static int lpc18xx_usb_otg_phy_probe(struct platform_device *pdev)
+{
+	struct phy_provider *phy_provider;
+	struct lpc18xx_usb_otg_phy *lpc;
+
+	lpc = devm_kzalloc(&pdev->dev, sizeof(*lpc), GFP_KERNEL);
+	if (!lpc)
+		return -ENOMEM;
+
+	lpc->reg = syscon_node_to_regmap(pdev->dev.of_node->parent);
+	if (IS_ERR(lpc->reg)) {
+		dev_err(&pdev->dev, "failed to get syscon\n");
+		return PTR_ERR(lpc->reg);
+	}
+
+	lpc->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(lpc->clk)) {
+		dev_err(&pdev->dev, "failed to get clock\n");
+		return PTR_ERR(lpc->clk);
+	}
+
+	lpc->phy = devm_phy_create(&pdev->dev, NULL, &lpc18xx_usb_otg_phy_ops);
+	if (IS_ERR(lpc->phy)) {
+		dev_err(&pdev->dev, "failed to create PHY\n");
+		return PTR_ERR(lpc->phy);
+	}
+
+	phy_set_drvdata(lpc->phy, lpc);
+
+	phy_provider = devm_of_phy_provider_register(&pdev->dev,
+						     of_phy_simple_xlate);
+
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id lpc18xx_usb_otg_phy_match[] = {
+	{ .compatible = "nxp,lpc1850-usb-otg-phy" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, lpc18xx_usb_otg_phy_match);
+
+static struct platform_driver lpc18xx_usb_otg_phy_driver = {
+	.probe		= lpc18xx_usb_otg_phy_probe,
+	.driver		= {
+		.name	= "lpc18xx-usb-otg-phy",
+		.of_match_table = lpc18xx_usb_otg_phy_match,
+	},
+};
+module_platform_driver(lpc18xx_usb_otg_phy_driver);
+
+MODULE_AUTHOR("Joachim Eastwood <manabian@gmail.com>");
+MODULE_DESCRIPTION("NXP LPC18xx/43xx USB OTG PHY driver");
+MODULE_LICENSE("GPL v2");

drivers/phy/phy-miphy28lp.c

@@ -1132,7 +1132,7 @@ static struct phy *miphy28lp_xlate(struct device *dev,
 	return miphy_phy->phy;
 }
 
-static struct phy_ops miphy28lp_ops = {
+static const struct phy_ops miphy28lp_ops = {
 	.init = miphy28lp_init,
 	.owner = THIS_MODULE,
 };
@@ -1268,7 +1268,6 @@ static struct platform_driver miphy28lp_driver = {
 	.probe = miphy28lp_probe,
 	.driver = {
 		.name = "miphy28lp-phy",
-		.owner = THIS_MODULE,
 		.of_match_table = miphy28lp_of_match,
 	}
 };

drivers/phy/phy-miphy365x.c

@@ -510,7 +510,7 @@ static struct phy *miphy365x_xlate(struct device *dev,
 	return miphy_phy->phy;
 }
 
-static struct phy_ops miphy365x_ops = {
+static const struct phy_ops miphy365x_ops = {
 	.init		= miphy365x_init,
 	.owner		= THIS_MODULE,
 };

drivers/phy/phy-mvebu-sata.c

@@ -75,7 +75,7 @@ static int phy_mvebu_sata_power_off(struct phy *phy)
 	return 0;
 }
 
-static struct phy_ops phy_mvebu_sata_ops = {
+static const struct phy_ops phy_mvebu_sata_ops = {
 	.power_on	= phy_mvebu_sata_power_on,
 	.power_off	= phy_mvebu_sata_power_off,
 	.owner		= THIS_MODULE,

drivers/phy/phy-omap-usb2.c

@@ -137,7 +137,7 @@ static int omap_usb_init(struct phy *x)
 	return 0;
 }
 
-static struct phy_ops ops = {
+static const struct phy_ops ops = {
 	.init		= omap_usb_init,
 	.power_on	= omap_usb_power_on,
 	.power_off	= omap_usb_power_off,

drivers/phy/phy-qcom-apq8064-sata.c

@@ -204,7 +204,7 @@ static int qcom_apq8064_sata_phy_exit(struct phy *generic_phy)
 	return 0;
 }
 
-static struct phy_ops qcom_apq8064_sata_phy_ops = {
+static const struct phy_ops qcom_apq8064_sata_phy_ops = {
 	.init		= qcom_apq8064_sata_phy_init,
 	.exit		= qcom_apq8064_sata_phy_exit,
 	.owner		= THIS_MODULE,

drivers/phy/phy-qcom-ipq806x-sata.c

@@ -126,7 +126,7 @@ static int qcom_ipq806x_sata_phy_exit(struct phy *generic_phy)
 	return 0;
 }
 
-static struct phy_ops qcom_ipq806x_sata_phy_ops = {
+static const struct phy_ops qcom_ipq806x_sata_phy_ops = {
 	.init		= qcom_ipq806x_sata_phy_init,
 	.exit		= qcom_ipq806x_sata_phy_exit,
 	.owner		= THIS_MODULE,

drivers/phy/phy-qcom-ufs-i.h

@@ -150,7 +150,7 @@ int ufs_qcom_phy_remove(struct phy *generic_phy,
 		       struct ufs_qcom_phy *ufs_qcom_phy);
 struct phy *ufs_qcom_phy_generic_probe(struct platform_device *pdev,
 			struct ufs_qcom_phy *common_cfg,
-			struct phy_ops *ufs_qcom_phy_gen_ops,
+			const struct phy_ops *ufs_qcom_phy_gen_ops,
 			struct ufs_qcom_phy_specific_ops *phy_spec_ops);
 int ufs_qcom_phy_calibrate(struct ufs_qcom_phy *ufs_qcom_phy,
 			struct ufs_qcom_phy_calibration *tbl_A, int tbl_size_A,

drivers/phy/phy-qcom-ufs-qmp-14nm.c

@@ -115,7 +115,7 @@ static int ufs_qcom_phy_qmp_14nm_is_pcs_ready(struct ufs_qcom_phy *phy_common)
 	return err;
 }
 
-static struct phy_ops ufs_qcom_phy_qmp_14nm_phy_ops = {
+static const struct phy_ops ufs_qcom_phy_qmp_14nm_phy_ops = {
 	.init		= ufs_qcom_phy_qmp_14nm_init,
 	.exit		= ufs_qcom_phy_exit,
 	.power_on	= ufs_qcom_phy_power_on,
@@ -191,7 +191,6 @@ static struct platform_driver ufs_qcom_phy_qmp_14nm_driver = {
 	.driver = {
 		.of_match_table = ufs_qcom_phy_qmp_14nm_of_match,
 		.name = "ufs_qcom_phy_qmp_14nm",
-		.owner = THIS_MODULE,
 	},
 };
 

drivers/phy/phy-qcom-ufs-qmp-20nm.c

@@ -171,7 +171,7 @@ static int ufs_qcom_phy_qmp_20nm_is_pcs_ready(struct ufs_qcom_phy *phy_common)
 	return err;
 }
 
-static struct phy_ops ufs_qcom_phy_qmp_20nm_phy_ops = {
+static const struct phy_ops ufs_qcom_phy_qmp_20nm_phy_ops = {
 	.init		= ufs_qcom_phy_qmp_20nm_init,
 	.exit		= ufs_qcom_phy_exit,
 	.power_on	= ufs_qcom_phy_power_on,
@@ -247,7 +247,6 @@ static struct platform_driver ufs_qcom_phy_qmp_20nm_driver = {
 	.driver = {
 		.of_match_table = ufs_qcom_phy_qmp_20nm_of_match,
 		.name = "ufs_qcom_phy_qmp_20nm",
-		.owner = THIS_MODULE,
 	},
 };
 

drivers/phy/phy-qcom-ufs.c

@@ -77,7 +77,7 @@ EXPORT_SYMBOL_GPL(ufs_qcom_phy_calibrate);
 
 struct phy *ufs_qcom_phy_generic_probe(struct platform_device *pdev,
 				struct ufs_qcom_phy *common_cfg,
-				struct phy_ops *ufs_qcom_phy_gen_ops,
+				const struct phy_ops *ufs_qcom_phy_gen_ops,
 				struct ufs_qcom_phy_specific_ops *phy_spec_ops)
 {
 	int err;

drivers/phy/phy-rcar-gen2.c

@@ -184,7 +184,7 @@ static int rcar_gen2_phy_power_off(struct phy *p)
 	return 0;
 }
 
-static struct phy_ops rcar_gen2_phy_ops = {
+static const struct phy_ops rcar_gen2_phy_ops = {
 	.init		= rcar_gen2_phy_init,
 	.exit		= rcar_gen2_phy_exit,
 	.power_on	= rcar_gen2_phy_power_on,

drivers/phy/phy-rockchip-usb.c

@@ -84,7 +84,7 @@ static int rockchip_usb_phy_power_on(struct phy *_phy)
 	return 0;
 }
 
-static struct phy_ops ops = {
+static const struct phy_ops ops = {
 	.power_on	= rockchip_usb_phy_power_on,
 	.power_off	= rockchip_usb_phy_power_off,
 	.owner		= THIS_MODULE,
@@ -146,7 +146,6 @@ static struct platform_driver rockchip_usb_driver = {
 	.probe		= rockchip_usb_phy_probe,
 	.driver		= {
 		.name	= "rockchip-usb-phy",
-		.owner	= THIS_MODULE,
 		.of_match_table = rockchip_usb_phy_dt_ids,
 	},
 };

drivers/phy/phy-samsung-usb2.c

@@ -71,7 +71,7 @@ static int samsung_usb2_phy_power_off(struct phy *phy)
 	return 0;
 }
 
-static struct phy_ops samsung_usb2_phy_ops = {
+static const struct phy_ops samsung_usb2_phy_ops = {
 	.power_on	= samsung_usb2_phy_power_on,
 	.power_off	= samsung_usb2_phy_power_off,
 	.owner		= THIS_MODULE,

drivers/phy/phy-spear1310-miphy.c

@@ -179,7 +179,7 @@ static const struct of_device_id spear1310_miphy_of_match[] = {
 };
 MODULE_DEVICE_TABLE(of, spear1310_miphy_of_match);
 
-static struct phy_ops spear1310_miphy_ops = {
+static const struct phy_ops spear1310_miphy_ops = {
 	.init = spear1310_miphy_init,
 	.exit = spear1310_miphy_exit,
 	.owner = THIS_MODULE,

drivers/phy/phy-spear1340-miphy.c

@@ -189,7 +189,7 @@ static const struct of_device_id spear1340_miphy_of_match[] = {
 };
 MODULE_DEVICE_TABLE(of, spear1340_miphy_of_match);
 
-static struct phy_ops spear1340_miphy_ops = {
+static const struct phy_ops spear1340_miphy_ops = {
 	.init = spear1340_miphy_init,
 	.exit = spear1340_miphy_exit,
 	.owner = THIS_MODULE,

drivers/phy/phy-stih41x-usb.c

@@ -112,7 +112,7 @@ static int stih41x_usb_phy_power_off(struct phy *phy)
 	return 0;
 }
 
-static struct phy_ops stih41x_usb_phy_ops = {
+static const struct phy_ops stih41x_usb_phy_ops = {
 	.init		= stih41x_usb_phy_init,
 	.power_on	= stih41x_usb_phy_power_on,
 	.power_off	= stih41x_usb_phy_power_off,

drivers/phy/phy-sun9i-usb.c

@@ -114,7 +114,7 @@ static int sun9i_usb_phy_exit(struct phy *_phy)
 	return 0;
 }
 
-static struct phy_ops sun9i_usb_phy_ops = {
+static const struct phy_ops sun9i_usb_phy_ops = {
 	.init		= sun9i_usb_phy_init,
 	.exit		= sun9i_usb_phy_exit,
 	.owner		= THIS_MODULE,

drivers/phy/phy-ti-pipe3.c

@@ -298,7 +298,7 @@ static int ti_pipe3_exit(struct phy *x)
 
 	return 0;
 }
-static struct phy_ops ops = {
+static const struct phy_ops ops = {
 	.init		= ti_pipe3_init,
 	.exit		= ti_pipe3_exit,
 	.power_on	= ti_pipe3_power_on,

drivers/phy/phy-tusb1210.c

@@ -53,7 +53,7 @@ static int tusb1210_power_off(struct phy *phy)
 	return 0;
 }
 
-static struct phy_ops phy_ops = {
+static const struct phy_ops phy_ops = {
 	.power_on = tusb1210_power_on,
 	.power_off = tusb1210_power_off,
 	.owner = THIS_MODULE,

drivers/phy/ulpi_phy.h

@@ -5,7 +5,7 @@
  * and it's controller, which is always the parent.
  */
 static inline struct phy
-*ulpi_phy_create(struct ulpi *ulpi, struct phy_ops *ops)
+*ulpi_phy_create(struct ulpi *ulpi, const struct phy_ops *ops)
 {
 	struct phy *phy;
 	int ret;