Merge branch 'sh/for-2.6.33' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6

* 'sh/for-2.6.33' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: Ensure all PG_dcache_dirty pages are written back.
  sh: mach-ecovec24: setup.c detailed correction
  serial: sh-sci: Convert tremaining ctrl_xxx I/O routines to __raw_xxx.
  serial: sh-sci: earlyprintk zero uartclk fix
  sh: Only use bl bit toggling for sleeping idle.
  sh: Restore bl bit toggling in idle loop.
  sh: Fix up MAX_DMA_CHANNELS definition when DMA is disabled.
  sh: dmaengine support for SH7785
  sh: dmaengine support for sh7724.

arch/sh/boards/mach-ecovec24/setup.c

@@ -128,8 +128,6 @@ static struct platform_device nor_flash_device = {
 
 /* SH Eth */
 #define SH_ETH_ADDR	(0xA4600000)
-#define SH_ETH_MAHR	(SH_ETH_ADDR + 0x1C0)
-#define SH_ETH_MALR	(SH_ETH_ADDR + 0x1C8)
 static struct resource sh_eth_resources[] = {
 	[0] = {
 		.start = SH_ETH_ADDR,
@@ -509,6 +507,7 @@ static struct platform_device sdhi1_device = {
 
 #else
 
+/* MMC SPI */
 static int mmc_spi_get_ro(struct device *dev)
 {
 	return gpio_get_value(GPIO_PTY6);
@@ -542,6 +541,7 @@ static struct spi_board_info spi_bus[] = {
 	},
 };
 
+/* MSIOF0 */
 static struct sh_msiof_spi_info msiof0_data = {
 	.num_chipselect = 1,
 };

arch/sh/include/asm/dma.h

@@ -20,8 +20,10 @@
 
 #ifdef CONFIG_NR_DMA_CHANNELS
 #  define MAX_DMA_CHANNELS	(CONFIG_NR_DMA_CHANNELS)
-#else
+#elif defined(CONFIG_NR_ONCHIP_DMA_CHANNELS)
 #  define MAX_DMA_CHANNELS	(CONFIG_NR_ONCHIP_DMA_CHANNELS)
+#else
+#  define MAX_DMA_CHANNELS	0
 #endif
 
 /*

arch/sh/include/cpu-sh4/cpu/dma-sh4a.h

@@ -19,10 +19,10 @@
 #elif defined(CONFIG_CPU_SUBTYPE_SH7723) || \
       defined(CONFIG_CPU_SUBTYPE_SH7724)
 #define DMTE0_IRQ	48	/* DMAC0A*/
-#define DMTE4_IRQ	40	/* DMAC0B */
-#define DMTE6_IRQ	42
-#define DMTE8_IRQ	76	/* DMAC1A */
-#define DMTE9_IRQ	77
+#define DMTE4_IRQ	76	/* DMAC0B */
+#define DMTE6_IRQ	40
+#define DMTE8_IRQ	42	/* DMAC1A */
+#define DMTE9_IRQ	43
 #define DMTE10_IRQ	72	/* DMAC1B */
 #define DMTE11_IRQ	73
 #define DMAE0_IRQ	78	/* DMA Error IRQ*/

arch/sh/kernel/cpu/sh4a/setup-sh7724.c

@@ -23,9 +23,23 @@
 #include <linux/notifier.h>
 #include <asm/suspend.h>
 #include <asm/clock.h>
+#include <asm/dma-sh.h>
 #include <asm/mmzone.h>
 #include <cpu/sh7724.h>
 
+/* DMA */
+static struct sh_dmae_pdata dma_platform_data = {
+	.mode = SHDMA_DMAOR1,
+};
+
+static struct platform_device dma_device = {
+	.name	= "sh-dma-engine",
+	.id		= -1,
+	.dev	= {
+		.platform_data	= &dma_platform_data,
+	},
+};
+
 /* Serial */
 static struct plat_sci_port scif0_platform_data = {
 	.mapbase        = 0xffe00000,
@@ -649,6 +663,7 @@ static struct platform_device *sh7724_devices[] __initdata = {
 	&tmu3_device,
 	&tmu4_device,
 	&tmu5_device,
+	&dma_device,
 	&rtc_device,
 	&iic0_device,
 	&iic1_device,

arch/sh/kernel/cpu/sh4a/setup-sh7785.c

@@ -14,6 +14,7 @@
 #include <linux/io.h>
 #include <linux/mm.h>
 #include <linux/sh_timer.h>
+#include <asm/dma-sh.h>
 #include <asm/mmzone.h>
 
 static struct plat_sci_port scif0_platform_data = {
@@ -294,6 +295,18 @@ static struct platform_device tmu5_device = {
 	.num_resources	= ARRAY_SIZE(tmu5_resources),
 };
 
+static struct sh_dmae_pdata dma_platform_data = {
+	.mode = (SHDMA_MIX_IRQ | SHDMA_DMAOR1),
+};
+
+static struct platform_device dma_device = {
+	.name           = "sh-dma-engine",
+	.id             = -1,
+	.dev            = {
+		.platform_data  = &dma_platform_data,
+	},
+};
+
 static struct platform_device *sh7785_devices[] __initdata = {
 	&scif0_device,
 	&scif1_device,
@@ -307,6 +320,7 @@ static struct platform_device *sh7785_devices[] __initdata = {
 	&tmu3_device,
 	&tmu4_device,
 	&tmu5_device,
+	&dma_device,
 };
 
 static int __init sh7785_devices_setup(void)

arch/sh/kernel/idle.c

@@ -62,6 +62,7 @@ void default_idle(void)
 		clear_thread_flag(TIF_POLLING_NRFLAG);
 		smp_mb__after_clear_bit();
 
+		set_bl_bit();
 		if (!need_resched()) {
 			local_irq_enable();
 			cpu_sleep();
@@ -69,6 +70,7 @@ void default_idle(void)
 			local_irq_enable();
 
 		set_thread_flag(TIF_POLLING_NRFLAG);
+		clear_bl_bit();
 	} else
 		poll_idle();
 }

arch/sh/mm/cache.c

@@ -133,12 +133,8 @@ void __update_cache(struct vm_area_struct *vma,
 	page = pfn_to_page(pfn);
 	if (pfn_valid(pfn)) {
 		int dirty = test_and_clear_bit(PG_dcache_dirty, &page->flags);
-		if (dirty) {
-			unsigned long addr = (unsigned long)page_address(page);
-
-			if (pages_do_alias(addr, address & PAGE_MASK))
-				__flush_purge_region((void *)addr, PAGE_SIZE);
-		}
+		if (dirty)
+			__flush_purge_region(page_address(page), PAGE_SIZE);
 	}
 }
 

drivers/serial/sh-sci.c

@@ -222,9 +222,9 @@ static inline void sci_init_pins(struct uart_port *port, unsigned int cflag)
 		   Set SCP6MD1,0 = {01} (output)  */
 		__raw_writew((data & 0x0fcf) | 0x1000, SCPCR);
 
-		data = ctrl_inb(SCPDR);
+		data = __raw_readb(SCPDR);
 		/* Set /RTS2 (bit6) = 0 */
-		ctrl_outb(data & 0xbf, SCPDR);
+		__raw_writeb(data & 0xbf, SCPDR);
 	}
 }
 #elif defined(CONFIG_CPU_SUBTYPE_SH7722)
@@ -897,11 +897,21 @@ static void sci_shutdown(struct uart_port *port)
 static void sci_set_termios(struct uart_port *port, struct ktermios *termios,
 			    struct ktermios *old)
 {
-	unsigned int status, baud, smr_val;
+	unsigned int status, baud, smr_val, max_baud;
 	int t = -1;
 
-	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
-	if (likely(baud))
+	/*
+	 * earlyprintk comes here early on with port->uartclk set to zero.
+	 * the clock framework is not up and running at this point so here
+	 * we assume that 115200 is the maximum baud rate. please note that
+	 * the baud rate is not programmed during earlyprintk - it is assumed
+	 * that the previous boot loader has enabled required clocks and
+	 * setup the baud rate generator hardware for us already.
+	 */
+	max_baud = port->uartclk ? port->uartclk / 16 : 115200;
+
+	baud = uart_get_baud_rate(port, termios, old, 0, max_baud);
+	if (likely(baud && port->uartclk))
 		t = SCBRR_VALUE(baud, port->uartclk);
 
 	do {