Merge branch 'omap-for-v3.17/dt' into omap-for-v3.18/dt

Merge the gta04 related changes that were too late for v3.17

arch/arm/boot/dts/Makefile

@@ -286,7 +286,9 @@ dtb-$(CONFIG_ARCH_OMAP3) += am3517-craneboard.dtb \
 	omap3-devkit8000.dtb \
 	omap3-evm.dtb \
 	omap3-evm-37xx.dtb \
-	omap3-gta04.dtb \
+	omap3-gta04a3.dtb \
+	omap3-gta04a4.dtb \
+	omap3-gta04a5.dtb \
 	omap3-igep0020.dtb \
 	omap3-igep0030.dtb \
 	omap3-ldp.dtb \

arch/arm/boot/dts/omap3-gta04.dts → arch/arm/boot/dts/omap3-gta04.dtsi

@@ -26,6 +26,10 @@ memory {
 		reg = <0x80000000 0x20000000>; /* 512 MB */
 	};
 
+	aliases {
+		display0 = &lcd;
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys";
 
@@ -74,9 +78,30 @@ lcd_in: endpoint {
 			};
 		};
 	};
+
+	hsusb2_phy: hsusb2_phy {
+		compatible = "usb-nop-xceiv";
+		reset-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
+	};
 };
 
 &omap3_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&hsusb2_pins
+	>;
+
+	hsusb2_pins: pinmux_hsusb2_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi1_cs3.hsusb2_data2 */
+			OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_clk.hsusb2_data7 */
+			OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_simo.hsusb2_data4 */
+			OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_somi.hsusb2_data5 */
+			OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs0.hsusb2_data6 */
+			OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs1.hsusb2_data3 */
+		>;
+	};
+
 	uart1_pins: pinmux_uart1_pins {
 		pinctrl-single,pins = <
 			0x152 (PIN_INPUT | MUX_MODE0)		/* uart1_rx.uart1_rx */
@@ -141,12 +166,31 @@ dss_dpi_pins: pinmux_dss_dpi_pins {
                        0x0da (PIN_OUTPUT | MUX_MODE0)   /* dss_data23.dss_data23 */
                >;
        };
+};
+
+&omap3_pmx_core2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&hsusb2_2_pins
+	>;
+
+	hsusb2_2_pins: pinmux_hsusb2_2_pins {
+		pinctrl-single,pins = <
+			OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)		/* etk_d10.hsusb2_clk */
+			OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)		/* etk_d11.hsusb2_stp */
+			OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d12.hsusb2_dir */
+			OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d13.hsusb2_nxt */
+			OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d14.hsusb2_data0 */
+			OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d15.hsusb2_data1 */
+		>;
+	};
 
 	spi_gpio_pins: spi_gpio_pinmux {
-		pinctrl-single,pins = <0x5a8 (PIN_OUTPUT | MUX_MODE4) /* clk */
-			0x5b6 (PIN_OUTPUT | MUX_MODE4) /* cs */
-			0x5b8 (PIN_OUTPUT | MUX_MODE4) /* tx */
-			0x5b4 (PIN_INPUT | MUX_MODE4) /* rx */
+		pinctrl-single,pins = <
+			OMAP3630_CORE2_IOPAD(0x25d8, PIN_OUTPUT | MUX_MODE4) /* clk */
+			OMAP3630_CORE2_IOPAD(0x25e6, PIN_OUTPUT | MUX_MODE4) /* cs */
+			OMAP3630_CORE2_IOPAD(0x25e8, PIN_OUTPUT | MUX_MODE4) /* tx */
+			OMAP3630_CORE2_IOPAD(0x25e4, PIN_INPUT | MUX_MODE4) /* rx */
 		>;
 	};
 };
@@ -196,6 +240,9 @@ tca6507@45 {
 		#size-cells = <0>;
 		reg = <0x45>;
 
+		gpio-controller;
+		#gpio-cells = <2>;
+
 		gta04_led0: red_aux@0 {
 			label = "gta04:red:aux";
 			reg = <0x0>;
@@ -216,11 +263,16 @@ gta04_led4: green_power@4 {
 			label = "gta04:green:power";
 			reg = <0x4>;
 		};
+
+		wifi_reset: wifi_reset@6 {
+			reg = <0x6>;
+			compatible = "gpio";
+		};
 	};
 
 	/* compass aka magnetometer */
 	hmc5843@1e {
-		compatible = "honeywell,hmc5843";
+		compatible = "honeywell,hmc5883l";
 		reg = <0x1e>;
 	};
 
@@ -248,6 +300,14 @@ &usb_otg_hs {
 	power = <50>;
 };
 
+&usbhshost {
+	port2-mode = "ehci-phy";
+};
+
+&usbhsehci {
+	phys = <0 &hsusb2_phy>;
+};
+
 &mmc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins>;
@@ -286,11 +346,37 @@ &charger {
 	bb_uamp = <150>;
 };
 
+/* spare */
+&vaux1 {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <3000000>;
+};
+
+/* sensors */
+&vaux2 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-always-on;
+};
+
+/* camera */
+&vaux3 {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+};
+
+/* WLAN/BT */
 &vaux4 {
 	regulator-min-microvolt = <2800000>;
 	regulator-max-microvolt = <3150000>;
 };
 
+/* GPS LNA */
+&vsim {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <3150000>;
+};
+
 /* Needed to power the DPI pins */
 &vpll2 {
 	regulator-always-on;
@@ -309,3 +395,57 @@ dpi_out: endpoint {
 		};
 	};
 };
+
+&gpmc {
+	ranges = <0 0 0x30000000 0x04>; /* CS0: NAND */
+
+	nand@0,0 {
+		reg = <0 0 0>; /* CS0, offset 0 */
+		nand-bus-width = <16>;
+		ti,nand-ecc-opt = "bch8";
+
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <44>;
+		gpmc,cs-wr-off-ns = <44>;
+		gpmc,adv-on-ns = <6>;
+		gpmc,adv-rd-off-ns = <34>;
+		gpmc,adv-wr-off-ns = <44>;
+		gpmc,we-off-ns = <40>;
+		gpmc,oe-off-ns = <54>;
+		gpmc,access-ns = <64>;
+		gpmc,rd-cycle-ns = <82>;
+		gpmc,wr-cycle-ns = <82>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+		gpmc,device-width = <2>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		x-loader@0 {
+			label = "X-Loader";
+			reg = <0 0x80000>;
+		};
+
+		bootloaders@80000 {
+			label = "U-Boot";
+			reg = <0x80000 0x1e0000>;
+		};
+
+		bootloaders_env@260000 {
+			label = "U-Boot Env";
+			reg = <0x260000 0x20000>;
+		};
+
+		kernel@280000 {
+			label = "Kernel";
+			reg = <0x280000 0x400000>;
+		};
+
+		filesystem@680000 {
+			label = "File System";
+			reg = <0x680000 0xf980000>;
+		};
+	};
+};

arch/arm/boot/dts/omap3-gta04a3.dts

+/*
+ * Copyright (C) 2014 H. Nikolaus Schaller <hns@goldelico.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "omap3-gta04.dtsi"
+
+/ {
+	model = "Goldelico GTA04A3";
+};
+
+&i2c2 {
+
+	/* alternate accelerometer that might be installed on some GTA04A3 boards */
+	lis302@1d {
+		compatible = "st,lis331dlh", "st,lis3lv02d";
+		reg = <0x1d>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <18 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>;
+		Vdd-supply = <&vaux2>;
+		Vdd_IO-supply = <&vaux2>;
+
+		st,click-single-x;
+		st,click-single-y;
+		st,click-single-z;
+		st,click-thresh-x = <8>;
+		st,click-thresh-y = <8>;
+		st,click-thresh-z = <10>;
+		st,click-click-time-limit = <9>;
+		st,click-latency = <50>;
+		st,irq1-click;
+		st,wakeup-x-lo;
+		st,wakeup-x-hi;
+		st,wakeup-y-lo;
+		st,wakeup-y-hi;
+		st,wakeup-z-lo;
+		st,wakeup-z-hi;
+		st,min-limit-x = <32>;
+		st,min-limit-y = <3>;
+		st,min-limit-z = <3>;
+		st,max-limit-x = <3>;
+		st,max-limit-y = <32>;
+		st,max-limit-z = <32>;
+	};
+};

arch/arm/boot/dts/omap3-gta04a4.dts

+/*
+ * Copyright (C) 2014 Marek Belisko <marek@goldelico.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "omap3-gta04.dtsi"
+
+/ {
+	model = "Goldelico GTA04A4";
+};

arch/arm/boot/dts/omap3-gta04a5.dts

+/*
+ * Copyright (C) 2014 H. Nikolaus Schaller <hns@goldelico.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "omap3-gta04.dtsi"
+
+/ {
+	model = "Goldelico GTA04A5";
+
+	sound {
+		ti,jack-det-gpio = <&twl_gpio 2 0>;    /* GTA04A5 only */
+	};
+};