priv is netdev private data and it cannot be
used after free_netdev() call. Using priv after free_netdev()
can cause UAF bug. Fix it by moving free_netdev() at the end of the
function.

Fixes: 1e0a8b13 ("tlan: cancel work at remove path")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

adpt is netdev private data and it cannot be
used after free_netdev() call. Using adpt after free_netdev()
can cause UAF bug. Fix it by moving free_netdev() at the end of the
function.

Fixes: 54e19bc7 ("net: qcom/emac: do not use devm on internal phy pdev")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case of netdev registration failure the code path will
jump to init_fail label:

init_fail:
	netdev_err(ndev, "init failed\n");
	moxart_mac_free_memory(ndev);
irq_map_fail:
	free_netdev(ndev);
	return ret;

So, there is no need to call free_netdev() before jumping
to error handling path, since it can cause UAF or double-free
bug.

Fixes: 6c821bd9 ("net: Add MOXA ART SoCs ethernet driver")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure that we disable each of the TX and RX queues in the TDMA and
RDMA control registers. This is a correctness change to be symmetrical
with the code that enables the TX and RX queues.
Tested-by: Maxime Ripard <maxime@cerno.tech>
Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ivan Mikhaylov says:

====================
net/ncsi: Add NCSI Intel OEM command to keep PHY link up

Add NCSI Intel OEM command to keep PHY link up and prevents any channel
resets during the host load on i210. Also includes dummy response handler for
Intel manufacturer id.

Changes from v1:
 1. sparse fixes about casts
 2. put it after ncsi_dev_state_probe_cis instead of
    ncsi_dev_state_probe_channel because sometimes channel is not ready
    after it
 3. inl -> intel
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the dummy response handler for Intel boards to prevent incorrect
handling of OEM commands.
Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This allows to keep PHY link up and prevents any channel resets during
the host load.

It is KEEP_PHY_LINK_UP option(Veto bit) in i210 datasheet which
block PHY reset and power state changes.
Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sparse reports:
net/ncsi/ncsi-rsp.c:406:24: warning: cast to restricted __be32
net/ncsi/ncsi-manage.c:732:33: warning: cast to restricted __be32
net/ncsi/ncsi-manage.c:756:25: warning: cast to restricted __be32
net/ncsi/ncsi-manage.c:779:25: warning: cast to restricted __be32
Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PHY_SPARX5_SERDES depends on OF so SPARX5_SWITCH should also depend
on OF since 'select' does not follow any dependencies.

WARNING: unmet direct dependencies detected for PHY_SPARX5_SERDES
  Depends on [n]: (ARCH_SPARX5 || COMPILE_TEST [=n]) && OF [=n] && HAS_IOMEM [=y]
  Selected by [y]:
  - SPARX5_SWITCH [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_MICROCHIP [=y] && NET_SWITCHDEV [=y] && HAS_IOMEM [=y]

Fixes: 3cfa11ba ("net: sparx5: add the basic sparx5 driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

IRQs are requested during driver's ndo_open() and then later
freed up in disable_interrupts() during driver unload.
A race exists where driver can set the CXGB4_FULL_INIT_DONE
flag in ndo_open() after the disable_interrupts() in driver
unload path checks it, and hence misses calling free_irq().

Fix by unregistering netdevice first and sync with driver's
ndo_open(). This ensures disable_interrupts() checks the flag
correctly and frees up the IRQs properly.

Fixes: b37987e8 ("cxgb4: Disable interrupts and napi before unregistering netdev")
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When reboot system, no power cycles, firmware is already downloaded,
return -EIO will break driver as error:
mt7921e: probe of 0000:03:00.0 failed with error -5

Skip firmware download and continue to probe.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Fixes: 1c099ab4 ("mt76: mt7921: add MCU support")
Signed-off-by: David S. Miller <davem@davemloft.net>

Since Mikrotik 10/25G NIC MDIO op emulation is not 100% reliable,
on rare occasions it can happen that some physical functions of
the NIC do not get initialized due to timeouted early MDIO op.

This changes the atl1c probe on Mikrotik 10/25G NIC not to
depend on MDIO op emulation.
Signed-off-by: Gatis Peisenieks <gatis@mikrotik.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

An earlier commit set the pps_lookup cookie, but the line
was somehow added to the wrong code block.  Correct this.

Fixes: 8602e40f ("ptp: Set lookup cookie when creating a PTP PPS source.")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While TCP stack scales reasonably well, there is still one part that
can be used to DDOS it.

IPv6 Packet too big messages have to lookup/insert a new route,
and if abused by attackers, can easily put hosts under high stress,
with many cpus contending on a spinlock while one is stuck in fib6_run_gc()

ip6_protocol_deliver_rcu()
 icmpv6_rcv()
  icmpv6_notify()
   tcp_v6_err()
    tcp_v6_mtu_reduced()
     inet6_csk_update_pmtu()
      ip6_rt_update_pmtu()
       __ip6_rt_update_pmtu()
        ip6_rt_cache_alloc()
         ip6_dst_alloc()
          dst_alloc()
           ip6_dst_gc()
            fib6_run_gc()
             spin_lock_bh() ...

Some of our servers have been hit by malicious ICMPv6 packets
trying to _increase_ the MTU/MSS of TCP flows.

We believe these ICMPv6 packets are a result of a bug in one ISP stack,
since they were blindly sent back for _every_ (small) packet sent to them.

These packets are for one TCP flow:
09:24:36.266491 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
09:24:36.266509 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
09:24:36.316688 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
09:24:36.316704 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
09:24:36.608151 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240

TCP stack can filter some silly requests :

1) MTU below IPV6_MIN_MTU can be filtered early in tcp_v6_err()
2) tcp_v6_mtu_reduced() can drop requests trying to increase current MSS.

This tests happen before the IPv6 routing stack is entered, thus
removing the potential contention and route exhaustion.

Note that IPv6 stack was performing these checks, but too late
(ie : after the route has been added, and after the potential
garbage collect war)

v2: fix typo caught by Martin, thanks !
v3: exports tcp_mtu_to_mss(), caught by David, thanks !

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We will fail to build with CONFIG_SKB_EXTENSIONS disabled after
8550ff8d ("skbuff: Release nfct refcount on napi stolen or re-used
skbs") since there is an unconditionally use of skb_ext_find() without
an appropriate stub. Simply build the code conditionally and properly
guard against both COFNIG_SKB_EXTENSIONS as well as
CONFIG_NET_TC_SKB_EXT being disabled.

Fixes: Fixes: 8550ff8d ("skbuff: Release nfct refcount on napi stolen or re-used skbs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixed indentation by removing extra spaces.
Signed-off-by: Roy, UjjaL <royujjal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If copy_from_sockptr() then we need to unlock before returning.

Fixes: d463126e ("net: sock: extend SO_TIMESTAMPING for PHC binding")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for net:

1) Do not refresh timeout in SYN_SENT for syn retransmissions.
   Add selftest for unreplied TCP connection, from Florian Westphal.

2) Fix null dereference from error path with hardware offload
   in nftables.

3) Remove useless nf_ct_gre_keymap_flush() from netns exit path,
   from Vasily Averin.

4) Missing rcu read-lock side in ctnetlink helper info dump,
   also from Vasily.

5) Do not mark RST in the reply direction coming after SYN packet
   for an out-of-sync entry, from Ali Abdallah and Florian Westphal.

6) Add tcp_ignore_invalid_rst sysctl to allow to disable out of
   segment RSTs, from Ali.

7) KCSAN fix for nf_conntrack_all_lock(), from Manfred Spraul.

8) Honor NFTA_LAST_SET in nft_last.

9) Fix incorrect arithmetics when restore last_jiffies in nft_last.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After redirecting, it's already a new path. So the old PMTU info should
be cleared. The IPv6 test "mtu exception plus redirect" should only
has redirect info without old PMTU.

The IPv4 test can not be changed because of legacy.

Fixes: ec810535 ("selftests: Add redirect tests")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the kernel doesn't enable option CONFIG_IPV6_SUBTREES, the RTA_SRC
info will not be exported to userspace in rt6_fill_node(). And ip cmd will
not print "from ::" to the route output. So remove this check.

Fixes: ec810535 ("selftests: Add redirect tests")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The "plat->phy_interface" variable is an enum and in this context GCC
will treat it as an unsigned int so the error handling is never
triggered.

Fixes: b9f0b2f6 ("net: stmmac: platform: fix probe for ACPI devices")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

plat->phy_interface is unsigned integer, so the condition
can't be less than zero and the warning will never printed.

Fixes: 30bba69d ("stmmac: pci: Add dwmac support for Loongson")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nf_conntrack_netlink.h does not exist, refer to nfnetlink_conntrack.h instead.
Signed-off-by: Duncan Roe <duncan_roe@optusnet.com.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

The goal of commit df789fe7 ("ipv6: Provide ipv6 version of
"disable_policy" sysctl") was to have the disable_policy from ipv4
available on ipv6.
However, it's not exactly the same mechanism. On IPv4, all packets coming
from an interface, which has disable_policy set, bypass the policy check.
For ipv6, this is done only for local packets, ie for packets destinated to
an address configured on the incoming interface.

Let's align ipv6 with ipv4 so that the 'disable_policy' sysctl has the same
effect for both protocols.

My first approach was to create a new kind of route cache entries, to be
able to set DST_NOPOLICY without modifying routes. This would have added a
lot of code. Because the local delivery path is already handled, I choose
to focus on the forwarding path to minimize code churn.

Fixes: df789fe7 ("ipv6: Provide ipv6 version of "disable_policy" sysctl")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently when the call to otx2_mbox_alloc_msg_cgx_mac_addr_update fails
the error return variable rc is being assigned -ENOMEM and does not
return early. rc is then re-assigned and the error case is not handled
correctly. Fix this by returning -ENOMEM rather than assigning rc.

Addresses-Coverity: ("Unused value")
Fixes: 79d2be38 ("octeontx2-pf: offload DMAC filters to CGX/RPM block")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Taehee Yoo says:

====================
net: fix bonding ipsec offload problems

This series fixes some problems related to bonding ipsec offload.

The 1, 5, and 8th patches are to add a missing rcu_read_lock().
The 2nd patch is to add null check code to bond_ipsec_add_sa.
When bonding interface doesn't have an active real interface, the
bond->curr_active_slave pointer is null.
But bond_ipsec_add_sa() uses that pointer without null check.
So that it results in null-ptr-deref.
The 3 and 4th patches are to replace xs->xso.dev with xs->xso.real_dev.
The 6th patch is to disallow to set ipsec offload if a real interface
type is bonding.
The 7th patch is to add struct bond_ipsec to manage SA.
If bond mode is changed, or active real interface is changed, SA should
be removed from old current active real interface then it should be added
to new active real interface.
But it can't, because it doesn't manage SA.
The 9th patch is to fix incorrect return value of bond_ipsec_offload_ok().

v1 -> v2:
 - Add 9th patch.
 - Do not print warning when there is no SA in bond_ipsec_add_sa_all().
 - Add comment for ipsec_lock.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

bond_ipsec_offload_ok() is called to check whether the interface supports
ipsec offload or not.
bonding interface support ipsec offload only in active-backup mode.
So, if a bond interface is not in active-backup mode, it should return
false but it returns true.

Fixes: a3b658cf ("bonding: allow xfrm offload setup post-module-load")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To dereference bond->curr_active_slave, it uses rcu_dereference().
But it and the caller doesn't acquire RCU so a warning occurs.
So add rcu_read_lock().

Splat looks like:
WARNING: suspicious RCU usage
5.13.0-rc6+ #1179 Not tainted
drivers/net/bonding/bond_main.c:571 suspicious
rcu_dereference_check() usage!

other info that might help us debug this:

rcu_scheduler_active = 2, debug_locks = 1
1 lock held by ping/974:
 #0: ffff888109e7db70 (sk_lock-AF_INET){+.+.}-{0:0},
at: raw_sendmsg+0x1303/0x2cb0

stack backtrace:
CPU: 2 PID: 974 Comm: ping Not tainted 5.13.0-rc6+ #1179
Call Trace:
 dump_stack+0xa4/0xe5
 bond_ipsec_offload_ok+0x1f4/0x260 [bonding]
 xfrm_output+0x179/0x890
 xfrm4_output+0xfa/0x410
 ? __xfrm4_output+0x4b0/0x4b0
 ? __ip_make_skb+0xecc/0x2030
 ? xfrm4_udp_encap_rcv+0x800/0x800
 ? ip_local_out+0x21/0x3a0
 ip_send_skb+0x37/0xa0
 raw_sendmsg+0x1bfd/0x2cb0

Fixes: 18cb261a ("bonding: support hardware encryption offload to slaves")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding has been supporting ipsec offload.
When SA is added, bonding just passes SA to its own active real interface.
But it doesn't manage SA.
So, when events(add/del real interface, active real interface change, etc)
occur, bonding can't handle that well because It doesn't manage SA.
So some problems(panic, UAF, refcnt leak)occur.

In order to make it stable, it should manage SA.
That's the reason why struct bond_ipsec is added.
When a new SA is added to bonding interface, it is stored in the
bond_ipsec list. And the SA is passed to a current active real interface.
If events occur, it uses bond_ipsec data to handle these events.
bond->ipsec_list is protected by bond->ipsec_lock.

If a current active real interface is changed, the following logic works.
1. delete all SAs from old active real interface
2. Add all SAs to the new active real interface.
3. If a new active real interface doesn't support ipsec offload or SA's
option, it sets real_dev to NULL.

Fixes: 18cb261a ("bonding: support hardware encryption offload to slaves")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding interface can be nested and it supports ipsec offload.
So, it allows setting the nested bonding + ipsec scenario.
But code does not support this scenario.
So, it should be disallowed.

interface graph:
bond2
   |
bond1
   |
eth0

The nested bonding + ipsec offload may not a real usecase.
So, disallowing this scenario is fine.

Fixes: 18cb261a ("bonding: support hardware encryption offload to slaves")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To dereference bond->curr_active_slave, it uses rcu_dereference().
But it and the caller doesn't acquire RCU so a warning occurs.
So add rcu_read_lock().

Test commands:
    ip netns add A
    ip netns exec A bash
    modprobe netdevsim
    echo "1 1" > /sys/bus/netdevsim/new_device
    ip link add bond0 type bond
    ip link set eth0 master bond0
    ip link set eth0 up
    ip link set bond0 up
    ip x s add proto esp dst 14.1.1.1 src 15.1.1.1 spi 0x07 mode \
transport reqid 0x07 replay-window 32 aead 'rfc4106(gcm(aes))' \
0x44434241343332312423222114131211f4f3f2f1 128 sel src 14.0.0.52/24 \
dst 14.0.0.70/24 proto tcp offload dev bond0 dir in
    ip x s f

Splat looks like:
=============================
WARNING: suspicious RCU usage
5.13.0-rc3+ #1168 Not tainted
-----------------------------
drivers/net/bonding/bond_main.c:448 suspicious rcu_dereference_check()
usage!

other info that might help us debug this:

rcu_scheduler_active = 2, debug_locks = 1
2 locks held by ip/705:
 #0: ffff888106701780 (&net->xfrm.xfrm_cfg_mutex){+.+.}-{3:3},
at: xfrm_netlink_rcv+0x59/0x80 [xfrm_user]
 #1: ffff8880075b0098 (&x->lock){+.-.}-{2:2},
at: xfrm_state_delete+0x16/0x30

stack backtrace:
CPU: 6 PID: 705 Comm: ip Not tainted 5.13.0-rc3+ #1168
Call Trace:
 dump_stack+0xa4/0xe5
 bond_ipsec_del_sa+0x16a/0x1c0 [bonding]
 __xfrm_state_delete+0x51f/0x730
 xfrm_state_delete+0x1e/0x30
 xfrm_state_flush+0x22f/0x390
 xfrm_flush_sa+0xd8/0x260 [xfrm_user]
 ? xfrm_flush_policy+0x290/0x290 [xfrm_user]
 xfrm_user_rcv_msg+0x331/0x660 [xfrm_user]
 ? rcu_read_lock_sched_held+0x91/0xc0
 ? xfrm_user_state_lookup.constprop.39+0x320/0x320 [xfrm_user]
 ? find_held_lock+0x3a/0x1c0
 ? mutex_lock_io_nested+0x1210/0x1210
 ? sched_clock_cpu+0x18/0x170
 netlink_rcv_skb+0x121/0x350
[ ... ]

Fixes: 18cb261a ("bonding: support hardware encryption offload to slaves")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two pointers in struct xfrm_state_offload, *dev, *real_dev.
These are used in callback functions of struct xfrmdev_ops.
The *dev points whether bonding interface or real interface.
If bonding ipsec offload is used, it points bonding interface If not,
it points real interface.
And real_dev always points real interface.
So, ixgbevf should always use real_dev instead of dev.
Of course, real_dev always not be null.

Test commands:
    ip link add bond0 type bond
    #eth0 is ixgbevf interface
    ip link set eth0 master bond0
    ip link set bond0 up
    ip x s add proto esp dst 14.1.1.1 src 15.1.1.1 spi 0x07 mode \
transport reqid 0x07 replay-window 32 aead 'rfc4106(gcm(aes))' \
0x44434241343332312423222114131211f4f3f2f1 128 sel src 14.0.0.52/24 \
dst 14.0.0.70/24 proto tcp offload dev bond0 dir in

Splat looks like:
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 6 PID: 688 Comm: ip Not tainted 5.13.0-rc3+ #1168
RIP: 0010:ixgbevf_ipsec_find_empty_idx+0x28/0x1b0 [ixgbevf]
Code: 00 00 0f 1f 44 00 00 55 53 48 89 fb 48 83 ec 08 40 84 f6 0f 84 9c
00 00 00 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <0f> b6 04 02
84 c0 74 08 3c 01 0f 8e 4c 01 00 00 66 81 3b 00 04 0f
RSP: 0018:ffff8880089af390 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000000000001
RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000000
RBP: ffff8880089af4f8 R08: 0000000000000003 R09: fffffbfff4287e11
R10: 0000000000000001 R11: ffff888005de8908 R12: 0000000000000000
R13: ffff88810936a000 R14: ffff88810936a000 R15: ffff888004d78040
FS:  00007fdf9883a680(0000) GS:ffff88811a400000(0000)
knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055bc14adbf40 CR3: 000000000b87c005 CR4: 00000000003706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 ixgbevf_ipsec_add_sa+0x1bf/0x9c0 [ixgbevf]
 ? rcu_read_lock_sched_held+0x91/0xc0
 ? ixgbevf_ipsec_parse_proto_keys.isra.9+0x280/0x280 [ixgbevf]
 ? lock_acquire+0x191/0x720
 ? bond_ipsec_add_sa+0x48/0x350 [bonding]
 ? lockdep_hardirqs_on_prepare+0x3e0/0x3e0
 ? rcu_read_lock_held+0x91/0xa0
 ? rcu_read_lock_sched_held+0xc0/0xc0
 bond_ipsec_add_sa+0x193/0x350 [bonding]
 xfrm_dev_state_add+0x2a9/0x770
 ? memcpy+0x38/0x60
 xfrm_add_sa+0x2278/0x3b10 [xfrm_user]
 ? xfrm_get_policy+0xaa0/0xaa0 [xfrm_user]
 ? register_lock_class+0x1750/0x1750
 xfrm_user_rcv_msg+0x331/0x660 [xfrm_user]
 ? rcu_read_lock_sched_held+0x91/0xc0
 ? xfrm_user_state_lookup.constprop.39+0x320/0x320 [xfrm_user]
 ? find_held_lock+0x3a/0x1c0
 ? mutex_lock_io_nested+0x1210/0x1210
 ? sched_clock_cpu+0x18/0x170
 netlink_rcv_skb+0x121/0x350
[ ... ]

Fixes: 272c2330 ("xfrm: bail early on slave pass over skb")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two pointers in struct xfrm_state_offload, *dev, *real_dev.
These are used in callback functions of struct xfrmdev_ops.
The *dev points whether bonding interface or real interface.
If bonding ipsec offload is used, it points bonding interface If not,
it points real interface.
And real_dev always points real interface.
So, netdevsim should always use real_dev instead of dev.
Of course, real_dev always not be null.

Test commands:
    ip netns add A
    ip netns exec A bash
    modprobe netdevsim
    echo "1 1" > /sys/bus/netdevsim/new_device
    ip link add bond0 type bond mode active-backup
    ip link set eth0 master bond0
    ip link set eth0 up
    ip link set bond0 up
    ip x s add proto esp dst 14.1.1.1 src 15.1.1.1 spi 0x07 mode \
transport reqid 0x07 replay-window 32 aead 'rfc4106(gcm(aes))' \
0x44434241343332312423222114131211f4f3f2f1 128 sel src 14.0.0.52/24 \
dst 14.0.0.70/24 proto tcp offload dev bond0 dir in

Splat looks like:
BUG: spinlock bad magic on CPU#5, kworker/5:1/53
 lock: 0xffff8881068c2cc8, .magic: 11121314, .owner: <none>/-1,
.owner_cpu: -235736076
CPU: 5 PID: 53 Comm: kworker/5:1 Not tainted 5.13.0-rc3+ #1168
Workqueue: events linkwatch_event
Call Trace:
 dump_stack+0xa4/0xe5
 do_raw_spin_lock+0x20b/0x270
 ? rwlock_bug.part.1+0x90/0x90
 _raw_spin_lock_nested+0x5f/0x70
 bond_get_stats+0xe4/0x4c0 [bonding]
 ? rcu_read_lock_sched_held+0xc0/0xc0
 ? bond_neigh_init+0x2c0/0x2c0 [bonding]
 ? dev_get_alias+0xe2/0x190
 ? dev_get_port_parent_id+0x14a/0x360
 ? rtnl_unregister+0x190/0x190
 ? dev_get_phys_port_name+0xa0/0xa0
 ? memset+0x1f/0x40
 ? memcpy+0x38/0x60
 ? rtnl_phys_switch_id_fill+0x91/0x100
 dev_get_stats+0x8c/0x270
 rtnl_fill_stats+0x44/0xbe0
 ? nla_put+0xbe/0x140
 rtnl_fill_ifinfo+0x1054/0x3ad0
[ ... ]

Fixes: 272c2330 ("xfrm: bail early on slave pass over skb")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If bond doesn't have real device, bond->curr_active_slave is null.
But bond_ipsec_add_sa() dereferences bond->curr_active_slave without
null checking.
So, null-ptr-deref would occur.

Test commands:
    ip link add bond0 type bond
    ip link set bond0 up
    ip x s add proto esp dst 14.1.1.1 src 15.1.1.1 spi \
0x07 mode transport reqid 0x07 replay-window 32 aead 'rfc4106(gcm(aes))' \
0x44434241343332312423222114131211f4f3f2f1 128 sel src 14.0.0.52/24 \
dst 14.0.0.70/24 proto tcp offload dev bond0 dir in

Splat looks like:
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 4 PID: 680 Comm: ip Not tainted 5.13.0-rc3+ #1168
RIP: 0010:bond_ipsec_add_sa+0xc4/0x2e0 [bonding]
Code: 85 21 02 00 00 4d 8b a6 48 0c 00 00 e8 75 58 44 ce 85 c0 0f 85 14
01 00 00 48 b8 00 00 00 00 00 fc ff df 4c 89 e2 48 c1 ea 03 <80> 3c 02
00 0f 85 fc 01 00 00 48 8d bb e0 02 00 00 4d 8b 2c 24 48
RSP: 0018:ffff88810946f508 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: ffff88810b4e8040 RCX: 0000000000000001
RDX: 0000000000000000 RSI: ffffffff8fe34280 RDI: ffff888115abe100
RBP: ffff88810946f528 R08: 0000000000000003 R09: fffffbfff2287e11
R10: 0000000000000001 R11: ffff888115abe0c8 R12: 0000000000000000
R13: ffffffffc0aea9a0 R14: ffff88800d7d2000 R15: ffff88810b4e8330
FS:  00007efc5552e680(0000) GS:ffff888119c00000(0000)
knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055c2530dbf40 CR3: 0000000103056004 CR4: 00000000003706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 xfrm_dev_state_add+0x2a9/0x770
 ? memcpy+0x38/0x60
 xfrm_add_sa+0x2278/0x3b10 [xfrm_user]
 ? xfrm_get_policy+0xaa0/0xaa0 [xfrm_user]
 ? register_lock_class+0x1750/0x1750
 xfrm_user_rcv_msg+0x331/0x660 [xfrm_user]
 ? rcu_read_lock_sched_held+0x91/0xc0
 ? xfrm_user_state_lookup.constprop.39+0x320/0x320 [xfrm_user]
 ? find_held_lock+0x3a/0x1c0
 ? mutex_lock_io_nested+0x1210/0x1210
 ? sched_clock_cpu+0x18/0x170
 netlink_rcv_skb+0x121/0x350
 ? xfrm_user_state_lookup.constprop.39+0x320/0x320 [xfrm_user]
 ? netlink_ack+0x9d0/0x9d0
 ? netlink_deliver_tap+0x17c/0xa50
 xfrm_netlink_rcv+0x68/0x80 [xfrm_user]
 netlink_unicast+0x41c/0x610
 ? netlink_attachskb+0x710/0x710
 netlink_sendmsg+0x6b9/0xb70
[ ...]

Fixes: 18cb261a ("bonding: support hardware encryption offload to slaves")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To dereference bond->curr_active_slave, it uses rcu_dereference().
But it and the caller doesn't acquire RCU so a warning occurs.
So add rcu_read_lock().

Test commands:
    ip link add dummy0 type dummy
    ip link add bond0 type bond
    ip link set dummy0 master bond0
    ip link set dummy0 up
    ip link set bond0 up
    ip x s add proto esp dst 14.1.1.1 src 15.1.1.1 spi 0x07 \
	    mode transport \
	    reqid 0x07 replay-window 32 aead 'rfc4106(gcm(aes))' \
	    0x44434241343332312423222114131211f4f3f2f1 128 sel \
	    src 14.0.0.52/24 dst 14.0.0.70/24 proto tcp offload \
	    dev bond0 dir in

Splat looks like:
=============================
WARNING: suspicious RCU usage
5.13.0-rc3+ #1168 Not tainted
-----------------------------
drivers/net/bonding/bond_main.c:411 suspicious rcu_dereference_check() usage!

other info that might help us debug this:

rcu_scheduler_active = 2, debug_locks = 1
1 lock held by ip/684:
 #0: ffffffff9a2757c0 (&net->xfrm.xfrm_cfg_mutex){+.+.}-{3:3},
at: xfrm_netlink_rcv+0x59/0x80 [xfrm_user]
   55.191733][  T684] stack backtrace:
CPU: 0 PID: 684 Comm: ip Not tainted 5.13.0-rc3+ #1168
Call Trace:
 dump_stack+0xa4/0xe5
 bond_ipsec_add_sa+0x18c/0x1f0 [bonding]
 xfrm_dev_state_add+0x2a9/0x770
 ? memcpy+0x38/0x60
 xfrm_add_sa+0x2278/0x3b10 [xfrm_user]
 ? xfrm_get_policy+0xaa0/0xaa0 [xfrm_user]
 ? register_lock_class+0x1750/0x1750
 xfrm_user_rcv_msg+0x331/0x660 [xfrm_user]
 ? rcu_read_lock_sched_held+0x91/0xc0
 ? xfrm_user_state_lookup.constprop.39+0x320/0x320 [xfrm_user]
 ? find_held_lock+0x3a/0x1c0
 ? mutex_lock_io_nested+0x1210/0x1210
 ? sched_clock_cpu+0x18/0x170
 netlink_rcv_skb+0x121/0x350
 ? xfrm_user_state_lookup.constprop.39+0x320/0x320 [xfrm_user]
 ? netlink_ack+0x9d0/0x9d0
 ? netlink_deliver_tap+0x17c/0xa50
 xfrm_netlink_rcv+0x68/0x80 [xfrm_user]
 netlink_unicast+0x41c/0x610
 ? netlink_attachskb+0x710/0x710
 netlink_sendmsg+0x6b9/0xb70
[ ... ]

Fixes: 18cb261a ("bonding: support hardware encryption offload to slaves")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit fixes a bug (found by syzkaller) that could cause spurious
double-initializations for congestion control modules, which could cause
memory leaks or other problems for congestion control modules (like CDG)
that allocate memory in their init functions.

The buggy scenario constructed by syzkaller was something like:

(1) create a TCP socket
(2) initiate a TFO connect via sendto()
(3) while socket is in TCP_SYN_SENT, call setsockopt(TCP_CONGESTION),
    which calls:
       tcp_set_congestion_control() ->
         tcp_reinit_congestion_control() ->
           tcp_init_congestion_control()
(4) receive ACK, connection is established, call tcp_init_transfer(),
    set icsk_ca_initialized=0 (without first calling cc->release()),
    call tcp_init_congestion_control() again.

Note that in this sequence tcp_init_congestion_control() is called
twice without a cc->release() call in between. Thus, for CC modules
that allocate memory in their init() function, e.g, CDG, a memory leak
may occur. The syzkaller tool managed to find a reproducer that
triggered such a leak in CDG.

The bug was introduced when that commit 8919a9b3 ("tcp: Only init
congestion control if not initialized already")
introduced icsk_ca_initialized and set icsk_ca_initialized to 0 in
tcp_init_transfer(), missing the possibility for a sequence like the
one above, where a process could call setsockopt(TCP_CONGESTION) in
state TCP_SYN_SENT (i.e. after the connect() or TFO open sendmsg()),
which would call tcp_init_congestion_control(). It did not intend to
reset any initialization that the user had already explicitly made;
it just missed the possibility of that particular sequence (which
syzkaller managed to find).

Fixes: 8919a9b3 ("tcp: Only init congestion control if not initialized already")
Reported-by: syzbot+f1e24a0594d4e3a895d3@syzkaller.appspotmail.com
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When multiple SKBs are merged to a new skb under napi GRO,
or SKB is re-used by napi, if nfct was set for them in the
driver, it will not be released while freeing their stolen
head state or on re-use.

Release nfct on napi's stolen or re-used SKBs, and
in gro_list_prepare, check conntrack metadata diff.

Fixes: 5c6b9460 ("net/mlx5e: CT: Handle misses after executing CT action")
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Subtract the jiffies that have passed by to current jiffies to fix last
used restoration.

Fixes: 836382dc ("netfilter: nf_tables: add last expression")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

NFTA_LAST_SET tells us if this expression has ever seen a packet, do not
ignore this attribute when restoring the ruleset.

Fixes: 836382dc ("netfilter: nf_tables: add last expression")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

KCSAN detected an data race with ipc/sem.c that is intentional.

As nf_conntrack_lock() uses the same algorithm: Update
nf_conntrack_core as well:

nf_conntrack_lock() contains
  a1) spin_lock()
  a2) smp_load_acquire(nf_conntrack_locks_all).

a1) actually accesses one lock from an array of locks.

nf_conntrack_locks_all() contains
  b1) nf_conntrack_locks_all=true (normal write)
  b2) spin_lock()
  b3) spin_unlock()

b2 and b3 are done for every lock.

This guarantees that nf_conntrack_locks_all() prevents any
concurrent nf_conntrack_lock() owners:
If a thread past a1), then b2) will block until that thread releases
the lock.
If the threat is before a1, then b3)+a1) ensure the write b1) is
visible, thus a2) is guaranteed to see the updated value.

But: This is only the latest time when b1) becomes visible.
It may also happen that b1) is visible an undefined amount of time
before the b3). And thus KCSAN will notice a data race.

In addition, the compiler might be too clever.

Solution: Use WRITE_ONCE().
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>