- 09 May, 2015 19 commits
-
-
Nick Kossifidis authored
FFT spectral scan is a functionality that makes sense to have its own debug flag. Signed-off-by:
Nick Kossifidis <mickflemm@gmail.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Eyal Reizer authored
* Interrupt request need to happen when the wilink chip is powered on and driving the wlan_irq line. This avoids spurious interrupt issues that are a result of different external pulls configuration on different platforms * Allow working with wl18xx level-low and falling edge irqs by configuring wl18xx to invert the device interrupt Signed-off-by:
Eyal Reizer <eyalr@ti.com> Signed-off-by:
-
Masanari Iida authored
This patch fix some spelling typo in drivers/net/wirless Signed-off-by:
Masanari Iida <standby24x7@gmail.com> Signed-off-by:
-
Cathy Luo authored
We will reset more_task_flag at the end of main process routine. This optimization will help to remove spinlock operations at couple of places in the code. Signed-off-by:
Cathy Luo <cluo@marvell.com> Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
-
Felix Fietkau authored
Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
-
Felix Fietkau authored
On some BCM5301x ARM devices, user space still needs to control some system GPIO pins for which no driver exists. This is a lot easier to do with a predictable GPIO base. Signed-off-by:
-
Hante Meuleman authored
With PCIE it is possible to support multiple devices with the same device type. They all load the same nvram file. In order to support this the nvram can specify which part of the nvram is for which pcie device. This patch adds support for these new types of nvram files. Reviewed-by:
Arend Van Spriel <arend@broadcom.com> Reviewed-by:
Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by:
Daniel (Deognyoun) Kim <dekim@broadcom.com> Signed-off-by:
Hante Meuleman <meuleman@broadcom.com> Signed-off-by:
-
Hante Meuleman authored
Reviewed-by:
-
Arend van Spriel authored
This patch adds support for the BCM4358 2x2 11ac device. Reviewed-by:
-
Arend van Spriel authored
commit 330b4e4b ("brcmfmac: Add wowl support for SDIO devices.") changed the behaviour by removing the MMC_PM_KEEP_POWER flag for non-wowl scenario, which needs to be restored. Another necessary change is to mark the card as being non-removable. With this in place the suspend resume test passes successfully doing: # echo devices > /sys/power/pm_test # echo mem > /sys/power/state Note that power may still be switched off when system is going in S3 state. Reported-by:
Fu, Zhonghui <<zhonghui.fu@linux.intel.com> Reviewed-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Arend van Spriel authored
When the sdio bus state is not ready to process we abort the interrupt service routine. This is not wanted as it keeps the interrupt source active. Better clear the interrupt source. Reviewed-by:
-
Arend van Spriel authored
This patch adds support for the BCM4324 B5 revision. This device is similar to BCM43241 from driver and firmware perspective. It is known to be used in Lenovo Thinkpad Tablet devices. Reviewed-by:
-
Arend van Spriel authored
The scheduled scan support depends on firmware supporting the PNO feature. This feature is optional so add a feature flag for this in the driver and announce scheduled scan support accordingly. Reviewed-by:
-
Arend van Spriel authored
Some feature flags were not described in the header file. Adding the description. Reviewed-by:
-
Arend van Spriel authored
When change the country code the available channels may change. So the wiphy bands should be updated accordingly. Reviewed-by:
-
Arend van Spriel authored
The driver was constructing a list of channels per wiphy band by querying the device. This list is not what the hardware is able to do as it is already filtered by the country setting in the device. As user-space may change the country this would require updating the channel list which is not recommended [1]. This patch introduces a superset of channels. The individual channels are disabled appropriately by querying the device. [1] http://mid.gmane.org/1426706320.3001.21.camel@sipsolutions.netReviewed-by:
-
Zhaoyang Liu authored
This patch fixes an issue where it was discovered that driver is setting invalid HT IEs to FW. This was happening because bug in parsing HT IE. Driver would incorrectly point to start of HT IE while FW only needs actual HT configuration - excluding EID and length. Signed-off-by:
Zhaoyang Liu <liuzy@marvell.com> Signed-off-by:
Avinash Patil <patila@marvell.com> Signed-off-by:
-
Avinash Patil authored
This patch reverts 'commit c5534844 ("mwifiex: enable aggregation for TID 6 and 7 streams")'. TID6 & TID7 is voice traffic which is quite time sensitive. Do not enable any type of aggregation on these TIDs. Signed-off-by:
-
Kalle Valo authored
Merge tag 'iwlwifi-next-for-kalle-2015-05-03' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next * major rework of the scan code (Luca) * some work on the thermal code (Chaya Rachel) * some work on the firwmare debugging infrastructure
-
- 03 May, 2015 1 commit
-
-
David Spinadel authored
Fix a copy paste bug that didn't copy wildcard SSIDs to scan requests. This bug causes scan with only wildcard SSID to be passive, and scans with more than one SSID to send only the direct probes. Fixes: 2a28ac14c518 ("iwlwifi: mvm: add common scan params to thw iwl_mvm_scan_params struct") Signed-off-by:David Spinadel <david.spinadel@intel.com> Reviewed-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 29 Apr, 2015 20 commits
-
-
Luciano Coelho authored
Some more tidbits left over from the legacy scan removal. Signed-off-by:
Luciano Coelho <luciano.coelho@intel.com> Signed-off-by:
-
Chaya Rachel Ivgi authored
The thermal throttling parameters were constant and hardcoded, not allowing changes for different NIC families. Change this so that the values are part of the NIC family configuration and are not constant (so they can be changed dynamically in the future). Signed-off-by:
Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com> Reviewed-by:
-
Johannes Berg authored
When a firmware restart is done, don't try to reprogram the keys to new slots but rather just keep the old key index, while skipping keys that weren't programmed before. Not only does this restore the state more faithfully, but it will also allow using the HW key index for internal purposes as an array index. Signed-off-by:
-
Luciano Coelho authored
The generic scan command functions are now irrelevant, since both sched and regular scans are in the same code. So rename this functions to dwell and isolate all the dwell-related setting to them. Keeping the dwell code separate makes it easier to compare the LMAC and UMAC versions. Signed-off-by:
-
Luciano Coelho authored
Having an LMAC counterpart for the existing UMAC flags function makes things more consistent and easy to compare and spot the differences. The flags are the same, but are in different bits, so unfortunately we can't use a single function for both APIs. Signed-off-by:
-
Luciano Coelho authored
Clean the code a little by moving all the flags into the right function. Additionally, rename the function, since "common" is now irrelevant. Signed-off-by:
-
David Spinadel authored
Signed-off-by:
-
Emmanuel Grumbach authored
When we use an external buffer, it is allocated from the t DRAM and can be as big as 64MB. This buffer is huge and might not be needed for the specific issue being chased. Especially if lots of dumps are going to be created. Allow to limit the size of the buffer in the configuration. Signed-off-by: -
Eliad Peller authored
qos_seq points (to a struct) inside the command response data. Make sure to free the response only after qos_seq is not needed anymore. type=bugfix bug=not-tracked fixes=I78c07110b59dcd389207bd2b168b0a2760839fe0 Change-Id: I619ce2c17e064dc98c7be9abc1e23175fdc8fb9a Reported-by:
Heng Luo <heng.luo@intel.com> Signed-off-by:
Eliad Peller <eliadx.peller@intel.com> Reviewed-on: https://gerrit.rds.intel.com/r/55381Reviewed-by:
-
Luciano Coelho authored
With just a few differences left in the UMAC scan functions now, we can merge them into one, taking care of the small difference according to the total number of iterations required. Signed-off-by:
-
Luciano Coelho authored
In theory, LMAC scans can handle a 32-bit delay, but since waiting for over 18 hours to start the scan is a bit silly and to keep it aligned with UMAC scans (which only support 16-bit delays), trim it down to 16-bits. This makes the LMAC vs. UMAC and the UMAC reg scan vs. UMAC sched scan code more similar. Signed-off-by:
-
Luciano Coelho authored
The last remaining difference between the regular scan and scheduled scan flows for LMAC is the FW capabilities check for EBS scans. Merge these checks into a new function and then combine the LMAC scan functions into a single one. Signed-off-by:
-
Luciano Coelho authored
As another step towards combining the scan and sched scan functions, add parameters that tell the scan function how many iterations we want (i.e. 1 for normal scan, more for scheduled scan) and that set the full scan multiplier (only meaningful for LMAC). Signed-off-by:
-
Luciano Coelho authored
The probe request to be added to both LMAC and UMAC scan commands are identical, so move the generation out of the LMAC/UMAC-specific code. Signed-off-by:
-
Luciano Coelho authored
To make things clearer, rename the iwl_mvm_scan_calc_params() function to iwl_mvm_calc_dwell() and make it calculate and fill in only dwell-related parameters. Signed-off-by:
-
Luciano Coelho authored
Now that both scheduled scan and regular scan SSID populating functions do the same thing, they can be combined into a single function. Signed-off-by:
-
Luciano Coelho authored
The firmware inverts the order of the SSIDs sent out in probe requests (for some reason). For regular scans, we've been passing the SSIDs in the opposite order so they go out in the order we want. With scheduled scans, we were not doing that, so they were sent out in reverse order of priority. Fix that by using the reverse order when populating the SSIDs array for scheduled scans as well. Signed-off-by:
-
Luciano Coelho authored
The only difference in the ssid_bitmap between LMAC and UMAC scans is that in LMAC bits 1 to 20 are used, while in UMAC bits 0 to 19 are used (*sigh*). So we can combine the bitmap creation into a single function and simply shift left if LMAC is used. Signed-off-by:
-
Luciano Coelho authored
Many parameters are common for all scans. Instead of parsing the cfg80211 scan and sched scan requests differently in each flow, move the parsing outside of the API/scan-type specific functions. In this way, we only need to differentiate between scan types once. Signed-off-by:
-
Luciano Coelho authored
Similarly to the regular scan patch, a lot of the UMAC and LMAC sched scan code is also almost identical. Grab the low hanging fruits by combining the obvious parts. Signed-off-by:
-
