Skip to content

L
linux
Switch branch/tag
  1. 02 Oct, 2017 17 commits
  3. 01 Oct, 2017 16 commits
  5. 30 Sep, 2017 3 commits
    • Colin Ian King's avatar
      mkiss: remove redundant check on len being zero · 45c1fd61
      Colin Ian King authored 
      The check on len is redundant as it is always greater than 1,
so just remove it and make the printk less complex.

Detected by CoverityScan, CID#1226729 ("Logically dead code")
Signed-off-by: default avatarColin Ian King <colin.king@canonical.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      45c1fd61
    • Maciej Żenczykowski's avatar
      net-ipv6: add support for sockopt(SOL_IPV6, IPV6_FREEBIND) · 84e14fe3
      Maciej Żenczykowski authored 
      So far we've been relying on sockopt(SOL_IP, IP_FREEBIND) being usable
even on IPv6 sockets.

However, it turns out it is perfectly reasonable to want to set freebind
on an AF_INET6 SOCK_RAW socket - but there is no way to set any SOL_IP
socket option on such a socket (they're all blindly errored out).

One use case for this is to allow spoofing src ip on a raw socket
via sendmsg cmsg.

Tested:
  built, and booted
  # python
  >>> import socket
  >>> SOL_IP = socket.SOL_IP
  >>> SOL_IPV6 = socket.IPPROTO_IPV6
  >>> IP_FREEBIND = 15
  >>> IPV6_FREEBIND = 78
  >>> s = socket.socket(socket.AF_INET6, socket.SOCK_DGRAM, 0)
  >>> s.getsockopt(SOL_IP, IP_FREEBIND)
  0
  >>> s.getsockopt(SOL_IPV6, IPV6_FREEBIND)
  0
  >>> s.setsockopt(SOL_IPV6, IPV6_FREEBIND, 1)
  >>> s.getsockopt(SOL_IP, IP_FREEBIND)
  1
  >>> s.getsockopt(SOL_IPV6, IPV6_FREEBIND)
  1
Signed-off-by: default avatarMaciej Żenczykowski <maze@google.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      84e14fe3
    • Mike Manning's avatar
      net: ipv6: send NS for DAD when link operationally up · 1f372c7b
      Mike Manning authored 
      The NS for DAD are sent on admin up as long as a valid qdisc is found.
A race condition exists by which these packets will not egress the
interface if the operational state of the lower device is not yet up.
The solution is to delay DAD until the link is operationally up
according to RFC2863. Rather than only doing this, follow the existing
code checks by deferring IPv6 device initialization altogether. The fix
allows DAD on devices like tunnels that are controlled by userspace
control plane. The fix has no impact on regular deployments, but means
that there is no IPv6 connectivity until the port has been opened in
the case of port-based network access control, which should be
desirable.
Signed-off-by: default avatarMike Manning <mmanning@brocade.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      1f372c7b
  7. 29 Sep, 2017 4 commits
    • Mitch Williams's avatar
      i40e: refactor FW version checking · 22b96551
      Mitch Williams authored 
      The i40e driver now supports two different devices with two different
firmware versions. So be smart about how we handle these. Move the FW
version macros to the appropriate header file, and add a convenience
macro that checks the version based on the device. Then use this macro
to check whether or not the driver can use the new link info API.
Signed-off-by: default avatarMitch Williams <mitch.a.williams@intel.com>
Tested-by: default avatarAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
      22b96551
    • Alan Brady's avatar
      i40e: Enable VF to negotiate number of allocated queues · a3f5aa90
      Alan Brady authored 
      Currently the PF allocates a default number of queues for each VF and
cannot be changed.  This patch enables the VF to request a different
number of queues allocated to it.  This patch also adds a new virtchnl
op and capability flag to facilitate this negotiation.

After the PF receives a request message, it will set a requested number
of queues for that VF.  Then when the VF resets, its VSI will get a new
number of queues allocated to it.

This is a best effort request and since we only allocate a guaranteed
default number, if the VF tries to ask for more than the guaranteed
number, there may not be enough in HW to accommodate it unless other
queues for other VFs are freed. It should also be noted decreasing the
number queues allocated to a VF to below the default will NOT enable the
allocation of more than 32 VFs per PF and will not free queues guaranteed
to each VF by default.
Signed-off-by: default avatarAlan Brady <alan.brady@intel.com>
Tested-by: default avatarAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
      a3f5aa90
    • Alan Brady's avatar
      i40evf: fix ring to vector mapping · c97fc9b6
      Alan Brady authored 
      The current implementation for mapping queues to vectors is broken
because it attempts to map each Tx and Rx ring to its own vector,
however we use combined queues so we should actually be mapping the
Tx/Rx rings together on one vector.

Also in the current implementation, in the case where we have more
queues than vectors, we attempt to group the queues together into
'chunks' and map each 'chunk' of queues to a vector.  Chunking them
together would be more ideal if, and only if, we only had RSS because of
the way the hashing algorithm works but in the case of a future patch
that enables VF ADq, round robin assignment is better and still works
with RSS.

This patch resolves both those issues and simplifies the code needed to
accomplish this.  Instead of treating the case where we have more queues
than vectors as special, if we notice our vector index is greater than
vectors, reset the vector index to zero and continue mapping.  This
should ensure that in both cases, whether we have enough vectors for
each queue or not, the queues get appropriately mapped.
Signed-off-by: default avatarAlan Brady <alan.brady@intel.com>
Tested-by: default avatarAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
      c97fc9b6
    • Jacob Keller's avatar
      i40e: shutdown all IRQs and disable MSI-X when suspended · b980c063
      Jacob Keller authored 
      On some platforms with a large number of CPUs, we will allocate many IRQ
vectors. When hibernating, the system will attempt to migrate all of the
vectors back to CPU0 when shutting down all the other CPUs. It is
possible that we have so many vectors that it cannot re-assign them to
CPU0. This is even more likely if we have many devices installed in one
platform.

The end result is failure to hibernate, as it is not possible to
shutdown the CPUs. We can avoid this by disabling MSI-X and clearing our
interrupt scheme when the device is suspended. A more ideal solution
would be some method for the stack to properly handle this for all
drivers, rather than on a case-by-case basis for each driver to fix
itself.

However, until this more ideal solution exists, we can do our part and
shutdown our IRQs during suspend, which should allow systems with
a large number of CPUs to safely suspend or hibernate.

It may be worth investigating if we should shut down even further when
we suspend as it may make the path cleaner, but this was the minimum fix
for the hibernation issue mentioned here.

Testing-hints:
  This affects systems with a large number of CPUs, and with multiple
  devices enabled. Without this change, those platforms are unable to
  hibernate at all.
Signed-off-by: default avatarJacob Keller <jacob.e.keller@intel.com>
Tested-by: default avatarAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
      b980c063
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7