Use eth_broadcast_addr() to set broadcast address instead of memset().
Signed-off-by: Lu Wei <luwei32@huawei.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Enable the support of creating all kinds of declared dummy packets
with the VLAN tags by inserting VLAN headers (single VLAN and QinQ
cases) if needed.
Decrease the number of declared dummy packets and increase in the
possible packet's combinations for adding switch rules.

This change enables support of creating filters that match both on
VLAN + tunnels properties in switchdev.
Signed-off-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@intel.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Enable support for adding TC rules that filter on the VLAN tag type
in switchdev mode.
Signed-off-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Enable support for adding TC rules with both C-tag and S-tag that can
filter on the inner and outer VLAN in QinQ for basic packets (not
tunneled cases).
Signed-off-by: Wiktor Pilarczyk <wiktor.pilarczyk@intel.com>
Signed-off-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@intel.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Yuwei Wang says:

====================
net, neigh: introduce interval_probe_time for periodic probe

This series adds a new option `interval_probe_time_ms` in net, neigh
for periodic probe, and add a limitation to prevent it set to 0
====================

Link: https://lore.kernel.org/r/20220629084832.2842973-1-wangyuweihx@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

commit ed6cd6a1 ("net, neigh: Set lower cap for neigh_managed_work rearming")
fixed a case when DELAY_PROBE_TIME is configured to 0, the processing of the
system work queue hog CPU to 100%, and further more we should introduce
a new option used by periodic probe
Signed-off-by: Yuwei Wang <wangyuweihx@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

add proc_dointvec_ms_jiffies_minmax to fit read msecs value to jiffies
with a limited range of values
Signed-off-by: Yuwei Wang <wangyuweihx@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Delete the redundant word 'slot'.
Signed-off-by: Jilin Yuan <yuanjilin@cdjrlc.com>
Link: https://lore.kernel.org/r/20220629081632.54445-1-yuanjilin@cdjrlc.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

On failure, devm_platform_ioremap_resource() returns a ERR_PTR() value
and not NULL. Fix return value checking by using IS_ERR() and return
PTR_ERR() as error value.

Fixes: 7dc54d3b ("net: pcs: add Renesas MII converter driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Clément Léger <clement.leger@bootlin.com>
Link: https://lore.kernel.org/r/20220628131259.3109124-1-yangyingliang@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The devm_platform_ioremap_resource() function never returns NULL.
It returns error pointers.
Signed-off-by: Peng Wu <wupeng58@huawei.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Clément Léger <clement.leger@bootlin.com>
Link: https://lore.kernel.org/r/20220628130920.49493-1-wupeng58@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add doc build infrastructure for txgbe driver.
Initialize PCI memory space for WangXun 10 Gigabit Ethernet devices.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://lore.kernel.org/r/20220628095530.889344-1-jiawenwu@trustnetic.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

There is no need to store the result of the addition back to variable count
after the addition. The store is redundant, replace += with just +

Cleans up clang scan build warning:
warning: Although the value stored to 'count' is used in the enclosing
expression, the value is never actually read from 'count'
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220628145406.183527-1-colin.i.king@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

br_switchdev_fdb_notify() creates an on-stack FDB info variable, and
initializes it member by member. As such, newly added fields which are
not initialized by br_switchdev_fdb_notify() will contain junk bytes
from the stack.

Other uses of struct switchdev_notifier_fdb_info have a struct
initializer which should put zeroes in the uninitialized fields.

Add a reminder above the structure for future developers. Recently
discussed during review.

Link: https://patchwork.kernel.org/project/netdevbpf/patch/20220524152144.40527-2-schultz.hans+netdev@gmail.com/#24877698
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20220524152144.40527-3-schultz.hans+netdev@gmail.com/#24912269Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://lore.kernel.org/r/20220628100831.2899434-1-vladimir.oltean@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Oleksij Rempel says:

====================
net: dsa: add pause stats support
====================

Link: https://lore.kernel.org/r/20220628085155.2591201-1-o.rempel@pengutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This switch is calculating tx/rx_bytes for all packets including pause.
So, include rx/tx_pause counter to rx/tx_packets to make tx/rx_bytes fit
to rx/tx_packets.

Link: https://lore.kernel.org/all/20220624220317.ckhx6z7cmzegvoqi@skbuf/Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add support for pause specific stats.

Tested on ksz9477.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add support for pause stats.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add support for pause stats
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The following is now supported:

  $ tc qdisc add PORT clsact
  $ tc filter add dev PORT egress ...
Signed-off-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, this script sets up the test scenario, which is supposed to end
in an inability of the system to negotiate a link. It then waits for a bit,
and verifies that the system can diagnose why the link was not established.

The wait time for the scenario where different link speeds are forced on
the two ends of a loopback cable, was set to 4 seconds, which exactly
covered it. As of a recent mlxsw firmware update, this time gets longer,
and this test starts failing.

The time that selftests currently wait for links to be established is
currently $WAIT_TIMEOUT, or 20 seconds. It seems reasonable that if this is
the time necessary to establish and bring up a link, it should also be
enough to determine that a link cannot be established and why.

Therefore in this patch, convert the sleeps to busywaits, so that if a
failure is established sooner (as is expected), the test runs quicker. And
use $WAIT_TIMEOUT as the time to wait.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A number of spelling and language mistakes in the flower section are
fixed. The spacing between the text inside some comments and the comment
symbols are also updated for consistency.
Signed-off-by: Walter Heymans <walter.heymans@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Arun Ramadoss says:

====================
net: dsa: microchip: use ksz_chip_reg for

This patch series tries to use the same approach as struct ksz8 for
register which has different address for different switch family. It
moves the struct ksz8 from ksz8.h to struct ksz_chip_reg. Based on the
switch detect, the corresponding mask, reg and shifts are assigned.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves the broadcast ctrl, multicast ctrl and start control
registers from ksz_chip_dat to ksz_chip_reg.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves the stp_ctrl_reg from the ksz_chip_data to ksz_chip_reg
structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The register size for the ksz8 switches is u8 and for ksz9477 series is
u16.  To have common struct for ksz series switches the size of reg is
increased from u8 to u16.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes the struct ksz8 from ksz8.h which is no longer
needed. The platform bus specific details are now deferenced through
dev->priv.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves ksz8->shifts from ksz8795.c to ksz_common.c. The shifts
are dereferenced using dev->info->shifts.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves the ksz8->masks from ksz8795.c to ksz_common.c. The
mask will be dereferenced using dev->info->masks.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves the ksz8->regs from ksz8795.c to the ksz_common.c. And
the regs is dereferrenced using dev->info->regs.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Biao Huang says:

====================
net: add more features for mtk-star-emac

Changes in v4:
1. correct the usage of spin_lock/__napi_schedule.
2. fix coding style as Jakub's comments.

Changes in v3:
1. refractor driver as Jakub's comments in patch
   "net: ethernet: mtk-star-emac: separate tx/rx handling with two NAPIs".
2. add acked-by as Rob's comments.
3. add a new patch for halp-duplex support in driver.

Changes in v2:
1. fix coding style as Bartosz's comments.
2. add reviewed-by as Bartosz's comments.

This series add more features for mtk-star-emac:
1. add reference clock pad selection for RMII;
2. add simple timing adjustment for RMII;
3. add support for MII;
4. add support for new IC MT8365;
5. separate tx/rx interrupt handling.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Current driver doesn't support half duplex correctly.
This patch enable half duplex capability in hardware.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: Yinghua Pan <ot_yinghua.pan@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current driver may lost tx interrupts under bidirectional test with iperf3,
which leads to some unexpected issues.

This patch let rx/tx interrupt enable/disable separately, and rx/tx are
handled in different NAPIs.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: Yinghua Pan <ot_yinghua.pan@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for MII interface.
If user wants to use MII, assign "MII" to "phy-mode" property in dts.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: Yinghua Pan <ot_yinghua.pan@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add description for new properties which will be parsed in driver.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add simple clock inversion for timing adjustment in driver.
Add property "mediatek,txc-inverse" or "mediatek,rxc-inverse" to
device node when necessary.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: Yinghua Pan <ot_yinghua.pan@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch add a new dts property named "mediatek,rmii-rxc" parsing
in driver, which will configure MAC to select which pin the RMII reference
clock is connected to, TXC or RXC.

TXC pad is the default reference clock pin. If user wants to use RXC pad
instead, add "mediatek,rmii-rxc" to corresponding device node.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: Yinghua Pan <ot_yinghua.pan@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add binding document for Ethernet on MT8365.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Reviewed-by: Bartosz Golaszewski <brgl@bgdev.pl>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add Ethernet driver support for MT8365 SoC.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: Yinghua Pan <ot_yinghua.pan@mediatek.com>
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the flags in request_irq() is IRQF_TRIGGER_NONE, the trigger method
is determined by "interrupt" property in dts.
So, modify the flag from IRQF_TRIGGER_FALLING to IRQF_TRIGGER_NONE.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: Yinghua Pan <ot_yinghua.pan@mediatek.com>
Reviewed-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Not all the SoC are using the same clock divider. Move the divider into
a compat structure specific to the SoCs.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>