- 03 Mar, 2016 40 commits
-
-
Alex Deucher authored
commit 24dd2f64 upstream. Avoids spew on resume for systems where sysfs may fail even on init. bug: https://bugzilla.kernel.org/show_bug.cgi?id=106851Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
NeilBrown authored
commit b02bab6b upstream. These async_XX functions are called from md/raid5 in an atomic section, between get_cpu() and put_cpu(), so they must not sleep. So use GFP_NOWAIT rather than GFP_IO. Dan Williams writes: Longer term async_tx needs to be merged into md directly as we can allocate this unmap data statically per-stripe rather than per request. Fixed: 7476bd79 ("async_pq: convert to dmaengine_unmap_data") Reported-and-tested-by:
Stanislav Samsonov <slava@annapurnalabs.com> Acked-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
NeilBrown <neilb@suse.com> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Roman Volkov authored
commit f9eccf24 upstream. The vt8500 clocksource driver declares itself as capable to handle the minimum delay of 4 cycles by passing the value into clockevents_config_and_register(). The vt8500_timer_set_next_event() requires the passed cycles value to be at least 16. The impact is that userspace hangs in nanosleep() calls with small delay intervals. This problem is reproducible in Linux 4.2 starting from: c6eb3f70 ('hrtimer: Get rid of hrtimer softirq') From Russell King, more detailed explanation: "It's a speciality of the StrongARM/PXA hardware. It takes a certain number of OSCR cycles for the value written to hit the compare registers. So, if a very small delta is written (eg, the compare register is written with a value of OSCR + 1), the OSCR will have incremented past this value before it hits the underlying hardware. The result is, that you end up waiting a very long time for the OSCR to wrap before the event fires. So, we introduce a check in set_next_event() to detect this and return -ETIME if the calculated delta is too small, which causes the generic clockevents code to retry after adding the min_delta specified in clockevents_config_and_register() to the current time value. min_delta must be sufficient that we don't re-trip the -ETIME check - if we do, we will return -ETIME, forward the next event time, try to set it, return -ETIME again, and basically lock the system up. So, min_delta must be larger than the check inside set_next_event(). A factor of two was chosen to ensure that this situation would never occur. The PXA code worked on PXA systems for years, and I'd suggest no one changes this mechanism without access to a wide range of PXA systems, otherwise they're risking breakage." Cc: Russell King <linux@arm.linux.org.uk> Acked-by:
Alexey Charkov <alchark@gmail.com> Signed-off-by:
Roman Volkov <rvolkov@v1ros.org> Signed-off-by:
Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by:
-
Roman Volkov authored
commit 0f090bf1 upstream. Since WM8650 has the same 'WMT' SDHC controller as WM8505, and the driver is already in the kernel, this node enables the controller support for WM8650 Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Thomas Gleixner authored
commit abc7e40c upstream. If a interrupt chip utilizes chip->buslock then free_irq() can deadlock in the following way: CPU0 CPU1 interrupt(X) (Shared or spurious) free_irq(X) interrupt_thread(X) chip_bus_lock(X) irq_finalize_oneshot(X) chip_bus_lock(X) synchronize_irq(X) synchronize_irq() waits for the interrupt thread to complete, i.e. forever. Solution is simple: Drop chip_bus_lock() before calling synchronize_irq() as we do with the irq_desc lock. There is nothing to be protected after the point where irq_desc lock has been released. This adds chip_bus_lock/unlock() to the remove_irq() code path, but that's actually correct in the case where remove_irq() is called on such an interrupt. The current users of remove_irq() are not affected as none of those interrupts is on a chip which requires buslock. Reported-by:
Fredrik Markström <fredrik.markstrom@gmail.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Peter Zijlstra authored
commit 9916e214 upstream. Remove the direct {push,pull} balancing operations from switched_{from,to}_dl() / prio_changed_dl() and use the balance callback queue. Again, err on the side of too many reschedules; since too few is a hard bug while too many is just annoying. Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: ktkhai@parallels.com Cc: rostedt@goodmis.org Cc: juri.lelli@gmail.com Cc: pang.xunlei@linaro.org Cc: oleg@redhat.com Cc: wanpeng.li@linux.intel.com Cc: umgwanakikbuti@gmail.com Link: http://lkml.kernel.org/r/20150611124742.968262663@infradead.orgSigned-off-by:
Byungchul Park <byungchul.park@lge.com> Signed-off-by:
-
Peter Zijlstra authored
commit 0ea60c20 upstream. In order to be able to use pull_dl_task() from a callback, we need to do away with the return value. Since the return value indicates if we should reschedule, do this inside the function. Since not all callers currently do this, this can increase the number of reschedules due rt balancing. Too many reschedules is not a correctness issues, too few are. Signed-off-by:
-
Peter Zijlstra authored
commit fd7a4bed upstream. Remove the direct {push,pull} balancing operations from switched_{from,to}_rt() / prio_changed_rt() and use the balance callback queue. Again, err on the side of too many reschedules; since too few is a hard bug while too many is just annoying. Signed-off-by:
-
Peter Zijlstra authored
commit 8046d680 upstream. In order to be able to use pull_rt_task() from a callback, we need to do away with the return value. Since the return value indicates if we should reschedule, do this inside the function. Since not all callers currently do this, this can increase the number of reschedules due rt balancing. Too many reschedules is not a correctness issues, too few are. Signed-off-by:
-
Peter Zijlstra authored
commit 4c9a4bc8 upstream. In order to remove dropping rq->lock from the switched_{to,from}()/prio_changed() sched_class methods, run the balance callbacks after it. We need to remove dropping rq->lock because its buggy, suppose using sched_setattr()/sched_setscheduler() to change a running task from FIFO to OTHER. By the time we get to switched_from_rt() the task is already enqueued on the cfs runqueues. If switched_from_rt() does pull_rt_task() and drops rq->lock, load-balancing can come in and move our task @p to another rq. The subsequent switched_to_fair() still assumes @p is on @rq and bad things will happen. By using balance callbacks we delay the load-balancing operations {rt,dl}x{push,pull} until we've done all the important work and the task is fully set up. Furthermore, the balance callbacks do not know about @p, therefore they cannot get confused like this. Reported-by:
Mike Galbraith <umgwanakikbuti@gmail.com> Signed-off-by:
-
Peter Zijlstra authored
commit e3fca9e7 upstream. Generalize the post_schedule() stuff into a balance callback list. This allows us to more easily use it outside of schedule() and cross sched_class. Signed-off-by:
-
Peter Zijlstra authored
commit 6c3b4d44 upstream. The idle post_schedule flag is just a vile waste of time, furthermore it appears unneeded, move the idle_enter_fair() call into pick_next_task_idle(). Signed-off-by:
Ingo Molnar <mingo@kernel.org> Cc: Byungchul Park <byungchul.park@lge.com> Signed-off-by:
-
Hannes Frederic Sowa authored
commit 415e3d3e upstream. The commit referenced in the Fixes tag incorrectly accounted the number of in-flight fds over a unix domain socket to the original opener of the file-descriptor. This allows another process to arbitrary deplete the original file-openers resource limit for the maximum of open files. Instead the sending processes and its struct cred should be credited. To do so, we add a reference counted struct user_struct pointer to the scm_fp_list and use it to account for the number of inflight unix fds. Fixes: 712f4aad ("unix: properly account for FDs passed over unix sockets") Reported-by:
David Herrmann <dh.herrmann@gmail.com> Cc: David Herrmann <dh.herrmann@gmail.com> Cc: Willy Tarreau <w@1wt.eu> Cc: Linus Torvalds <torvalds@linux-foundation.org> Suggested-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Manish Chopra authored
commit ad6afbe9 upstream. The scratchpad is a shared block between all functions of a given device. Due to HW limitations, we can't properly close its parity notifications to all functions on legal flows. E.g., it's possible that while taking a register dump from one function a parity error would be triggered on other functions. Today driver doesn't consider this parity as a 'real' parity unless its being accompanied by additional indications [which would happen in a real parity scenario]; But it does print notifications for such events in the system logs. This eliminates such prints - in case of real parities driver would have additional indications; But if this is the only signal user will not even see a parity being logged in the system. Signed-off-by:
Manish Chopra <Manish.Chopra@qlogic.com> Signed-off-by:
Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by:
Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by:
Patrick Schaaf <netdev@bof.de> Tested-by:
-
Olga Kornievskaia authored
commit a41cbe86 upstream. A test case is as the description says: open(foobar, O_WRONLY); sleep() --> reboot the server close(foobar) The bug is because in nfs4state.c in nfs4_reclaim_open_state() a few line before going to restart, there is clear_bit(NFS4CLNT_RECLAIM_NOGRACE, &state->flags). NFS4CLNT_RECLAIM_NOGRACE is a flag for the client states not open owner states. Value of NFS4CLNT_RECLAIM_NOGRACE is 4 which is the value of NFS_O_WRONLY_STATE in nfs4_state->flags. So clearing it wipes out state and when we go to close it, “call_close” doesn’t get set as state flag is not set and CLOSE doesn’t go on the wire. Signed-off-by:
Olga Kornievskaia <aglo@umich.edu> Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
-
Christophe Leroy authored
commit 0ff28d9f upstream. Using sendfile with below small program to get MD5 sums of some files, it appear that big files (over 64kbytes with 4k pages system) get a wrong MD5 sum while small files get the correct sum. This program uses sendfile() to send a file to an AF_ALG socket for hashing. /* md5sum2.c */ #include <stdio.h> #include <stdlib.h> #include <unistd.h> #include <string.h> #include <fcntl.h> #include <sys/socket.h> #include <sys/stat.h> #include <sys/types.h> #include <linux/if_alg.h> int main(int argc, char **argv) { int sk = socket(AF_ALG, SOCK_SEQPACKET, 0); struct stat st; struct sockaddr_alg sa = { .salg_family = AF_ALG, .salg_type = "hash", .salg_name = "md5", }; int n; bind(sk, (struct sockaddr*)&sa, sizeof(sa)); for (n = 1; n < argc; n++) { int size; int offset = 0; char buf[4096]; int fd; int sko; int i; fd = open(argv[n], O_RDONLY); sko = accept(sk, NULL, 0); fstat(fd, &st); size = st.st_size; sendfile(sko, fd, &offset, size); size = read(sko, buf, sizeof(buf)); for (i = 0; i < size; i++) printf("%2.2x", buf[i]); printf(" %s\n", argv[n]); close(fd); close(sko); } exit(0); } Test below is done using official linux patch files. First result is with a software based md5sum. Second result is with the program above. root@vgoip:~# ls -l patch-3.6.* -rw-r--r-- 1 root root 64011 Aug 24 12:01 patch-3.6.2.gz -rw-r--r-- 1 root root 94131 Aug 24 12:01 patch-3.6.3.gz root@vgoip:~# md5sum patch-3.6.* b3ffb9848196846f31b2ff133d2d6443 patch-3.6.2.gz c5e8f687878457db77cb7158c38a7e43 patch-3.6.3.gz root@vgoip:~# ./md5sum2 patch-3.6.* b3ffb9848196846f31b2ff133d2d6443 patch-3.6.2.gz 5fd77b24e68bb24dcc72d6e57c64790e patch-3.6.3.gz After investivation, it appears that sendfile() sends the files by blocks of 64kbytes (16 times PAGE_SIZE). The problem is that at the end of each block, the SPLICE_F_MORE flag is missing, therefore the hashing operation is reset as if it was the end of the file. This patch adds SPLICE_F_MORE to the flags when more data is pending. With the patch applied, we get the correct sums: root@vgoip:~# md5sum patch-3.6.* b3ffb9848196846f31b2ff133d2d6443 patch-3.6.2.gz c5e8f687878457db77cb7158c38a7e43 patch-3.6.3.gz root@vgoip:~# ./md5sum2 patch-3.6.* b3ffb9848196846f31b2ff133d2d6443 patch-3.6.2.gz c5e8f687878457db77cb7158c38a7e43 patch-3.6.3.gz Signed-off-by:
Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by:
Jens Axboe <axboe@fb.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Sasha Levin authored
commit 74e98eb0 upstream. There was no verification that an underlying transport exists when creating a connection, this would cause dereferencing a NULL ptr. It might happen on sockets that weren't properly bound before attempting to send a message, which will cause a NULL ptr deref: [135546.047719] kasan: GPF could be caused by NULL-ptr deref or user memory accessgeneral protection fault: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC KASAN [135546.051270] Modules linked in: [135546.051781] CPU: 4 PID: 15650 Comm: trinity-c4 Not tainted 4.2.0-next-20150902-sasha-00041-gbaa1222-dirty #2527 [135546.053217] task: ffff8800835bc000 ti: ffff8800bc708000 task.ti: ffff8800bc708000 [135546.054291] RIP: __rds_conn_create (net/rds/connection.c:194) [135546.055666] RSP: 0018:ffff8800bc70fab0 EFLAGS: 00010202 [135546.056457] RAX: dffffc0000000000 RBX: 0000000000000f2c RCX: ffff8800835bc000 [135546.057494] RDX: 0000000000000007 RSI: ffff8800835bccd8 RDI: 0000000000000038 [135546.058530] RBP: ffff8800bc70fb18 R08: 0000000000000001 R09: 0000000000000000 [135546.059556] R10: ffffed014d7a3a23 R11: ffffed014d7a3a21 R12: 0000000000000000 [135546.060614] R13: 0000000000000001 R14: ffff8801ec3d0000 R15: 0000000000000000 [135546.061668] FS: 00007faad4ffb700(0000) GS:ffff880252000000(0000) knlGS:0000000000000000 [135546.062836] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [135546.063682] CR2: 000000000000846a CR3: 000000009d137000 CR4: 00000000000006a0 [135546.064723] Stack: [135546.065048] ffffffffafe2055c ffffffffafe23fc1 ffffed00493097bf ffff8801ec3d0008 [135546.066247] 0000000000000000 00000000000000d0 0000000000000000 ac194a24c0586342 [135546.067438] 1ffff100178e1f78 ffff880320581b00 ffff8800bc70fdd0 ffff880320581b00 [135546.068629] Call Trace: [135546.069028] ? __rds_conn_create (include/linux/rcupdate.h:856 net/rds/connection.c:134) [135546.069989] ? rds_message_copy_from_user (net/rds/message.c:298) [135546.071021] rds_conn_create_outgoing (net/rds/connection.c:278) [135546.071981] rds_sendmsg (net/rds/send.c:1058) [135546.072858] ? perf_trace_lock (include/trace/events/lock.h:38) [135546.073744] ? lockdep_init (kernel/locking/lockdep.c:3298) [135546.074577] ? rds_send_drop_to (net/rds/send.c:976) [135546.075508] ? __might_fault (./arch/x86/include/asm/current.h:14 mm/memory.c:3795) [135546.076349] ? __might_fault (mm/memory.c:3795) [135546.077179] ? rds_send_drop_to (net/rds/send.c:976) [135546.078114] sock_sendmsg (net/socket.c:611 net/socket.c:620) [135546.078856] SYSC_sendto (net/socket.c:1657) [135546.079596] ? SYSC_connect (net/socket.c:1628) [135546.080510] ? trace_dump_stack (kernel/trace/trace.c:1926) [135546.081397] ? ring_buffer_unlock_commit (kernel/trace/ring_buffer.c:2479 kernel/trace/ring_buffer.c:2558 kernel/trace/ring_buffer.c:2674) [135546.082390] ? trace_buffer_unlock_commit (kernel/trace/trace.c:1749) [135546.083410] ? trace_event_raw_event_sys_enter (include/trace/events/syscalls.h:16) [135546.084481] ? do_audit_syscall_entry (include/trace/events/syscalls.h:16) [135546.085438] ? trace_buffer_unlock_commit (kernel/trace/trace.c:1749) [135546.085515] rds_ib_laddr_check(): addr 36.74.25.172 ret -99 node type -1 Acked-by:
Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
-
Marcelo Leitner authored
commit 77751427 upstream. Currently we don't check if the new MTU is valid or not and this allows one to configure a smaller than minimum allowed by RFCs or even bigger than interface own MTU, which is a problem as it may lead to packet drops. If you have a daemon like NetworkManager running, this may be exploited by remote attackers by forging RA packets with an invalid MTU, possibly leading to a DoS. (NetworkManager currently only validates for values too small, but not for too big ones.) The fix is just to make sure the new value is valid. That is, between IPV6_MIN_MTU and interface's MTU. Note that similar check is already performed at ndisc_router_discovery(), for when kernel itself parses the RA. Signed-off-by:
Marcelo Ricardo Leitner <mleitner@redhat.com> Signed-off-by:
Sabrina Dubroca <sd@queasysnail.net> Signed-off-by:
-
James Hogan authored
commit 585bb8f9 upstream. If either of the memory allocations in kvm_arch_vcpu_create() fail, the vcpu which has been allocated and kvm_vcpu_init'd doesn't get uninit'd in the error handling path. Add a call to kvm_vcpu_uninit() to fix this. Fixes: 669e846e ("KVM/MIPS32: MIPS arch specific APIs for KVM") Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Gleb Natapov <gleb@kernel.org> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
James Hogan authored
commit c5c2a3b9 upstream. The immediate field of the CACHE instruction is signed, so ensure that it gets sign extended by casting it to an int16_t rather than just masking the low 16 bits. Fixes: e685c689 ("KVM/MIPS32: Privileged instruction/target branch emulation.") Signed-off-by:
-
James Hogan authored
commit 002374f3 upstream. ASID restoration on guest resume should determine the guest execution mode based on the guest Status register rather than bit 30 of the guest PC. Fix the two places in locore.S that do this, loading the guest status from the cop0 area. Note, this assembly is specific to the trap & emulate implementation of KVM, so it doesn't need to check the supervisor bit as that mode is not implemented in the guest. Fixes: b680f70f ("KVM/MIPS32: Entry point for trampolining to...") Signed-off-by:
-
Al Viro authored
commit c2338f2d upstream. Dentry that had been through (or into) __dentry_kill() might be seen by shrink_dentry_list(); that's normal, it'll be taken off the shrink list and freed if __dentry_kill() has already finished. The problem is, its ->d_parent might be pointing to already freed dentry, so lock_parent() needs to be careful. We need to check that dentry hasn't already gone into __dentry_kill() *and* grab rcu_read_lock() before dropping ->d_lock - the latter makes sure that whatever we see in ->d_parent after dropping ->d_lock it won't be freed until we drop rcu_read_lock(). Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Linus Torvalds authored
commit 9f12600f upstream. lock_parent() very much on purpose does nested locking of dentries, and is careful to maintain the right order (lock parent first). But because it didn't annotate the nested locking order, lockdep thought it might be a deadlock on d_lock, and complained. Add the proper annotation for the inner locking of the child dentry to make lockdep happy. Introduced by commit 046b961b ("shrink_dentry_list(): take parent's ->d_lock earlier"). Reported-and-tested-by:
Josh Boyer <jwboyer@fedoraproject.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Al Viro authored
commit 8cbf74da upstream. it's 1 in the only remaining caller. Signed-off-by:
-
Al Viro authored
commit b2b80195 upstream. We have the same problem with ->d_lock order in the inner loop, where we are dropping references to ancestors. Same solution, basically - instead of using dentry_kill() we use lock_parent() (introduced in the previous commit) to get that lock in a safe way, recheck ->d_count (in case if lock_parent() has ended up dropping and retaking ->d_lock and somebody managed to grab a reference during that window), trylock the inode->i_lock and use __dentry_kill() to do the rest. Signed-off-by:
-
Al Viro authored
commit 046b961b upstream. The cause of livelocks there is that we are taking ->d_lock on dentry and its parent in the wrong order, forcing us to use trylock on the parent's one. d_walk() takes them in the right order, and unfortunately it's not hard to create a situation when shrink_dentry_list() can't make progress since trylock keeps failing, and shrink_dcache_parent() or check_submounts_and_drop() keeps calling d_walk() disrupting the very shrink_dentry_list() it's waiting for. Solution is straightforward - if that trylock fails, let's unlock the dentry itself and take locks in the right order. We need to stabilize ->d_parent without holding ->d_lock, but that's doable using RCU. And we'd better do that in the very beginning of the loop in shrink_dentry_list(), since the checks on refcount, etc. would need to be redone anyway. That deals with a half of the problem - killing dentries on the shrink list itself. Another one (dropping their parents) is in the next commit. locking parent is interesting - it would be easy to do rcu_read_lock(), lock whatever we think is a parent, lock dentry itself and check if the parent is still the right one. Except that we need to check that *before* locking the dentry, or we are risking taking ->d_lock out of order. Fortunately, once the D1 is locked, we can check if D2->d_parent is equal to D1 without the need to lock D2; D2->d_parent can start or stop pointing to D1 only under D1->d_lock, so taking D1->d_lock is enough. In other words, the right solution is rcu_read_lock/lock what looks like parent right now/check if it's still our parent/rcu_read_unlock/lock the child. Signed-off-by:
-
Al Viro authored
commit ff2fde99 upstream. Result will be massaged to saner shape in the next commits. It is ugly, no questions - the point of that one is to be a provably equivalent transformation (and it might be worth splitting a bit more). Signed-off-by:
-
Al Viro authored
commit e55fd011 upstream. ... into trylocks and everything else. The latter (actual killing) is __dentry_kill(). Signed-off-by:
-
Al Viro authored
commit 64fd72e0 upstream. It can happen only when dentry_kill() is called with unlock_on_failure equal to 0 - other callers had dentry pinned until the moment they've got ->d_lock and DCACHE_DENTRY_KILLED is set only after lockref_mark_dead(). IOW, only one of three call sites of dentry_kill() might end up reaching that code. Just move it there. Signed-off-by:
-
Hariprasad S authored
commit 67f1aee6 upstream. The cxgb3_*_send() functions return NET_XMIT_ values, which are positive integers values. So don't treat positive return values as an error. Signed-off-by:
Steve Wise <swise@opengridcomputing.com> Signed-off-by:
Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> [a pox on developers and maintainers who do not cc: stable for bug fixes like this - gregkh] Signed-off-by:
-
Corey Wright authored
Modify mm_access() calls in fs/proc/task_mmu.c and fs/proc/task_nommu.c to have the mode include PTRACE_MODE_FSCREDS so accessing /proc/pid/maps and /proc/pid/pagemap is not denied to all users. In backporting upstream commit caaee623 to pre-3.18 kernel versions it was overlooked that mm_access() is used in fs/proc/task_*mmu.c as those calls were removed in 3.18 (by upstream commit 29a40ace) and did not exist at the time of the original commit. Signed-off-by:
Corey Wright <undefined@pobox.com> Acked-by:
Jann Horn <jann@thejh.net> Signed-off-by:
-
Bjørn Mork authored
commit d061c1ca upstream. Thomas reports: T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=05c6 ProdID=6001 Rev=00.00 S: Manufacturer=USB Modem S: Product=USB Modem S: SerialNumber=1234567890ABCDEF C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage Reported-by:
Thomas Schäfer <tschaefer@t-online.de> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Andrey Skvortsov authored
commit 3158a8d4 upstream. $ lsusb: Bus 001 Device 101: ID 1e0e:9001 Qualcomm / Option $ usb-devices: T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=101 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 2 P: Vendor=1e0e ProdID=9001 Rev= 2.32 S: Manufacturer=SimTech, Incorporated S: Product=SimTech, Incorporated S: SerialNumber=0123456789ABCDEF C:* #Ifs= 7 Cfg#= 1 Atr=80 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) The last interface (6) is used for Android Composite ADB interface. Serial port layout: 0: QCDM/DIAG 1: NMEA 2: AT 3: AT/PPP 4: audio Signed-off-by:
Andrey Skvortsov <andrej.skvortzov@gmail.com> Signed-off-by:
-
Ken Lin authored
commit 6627ae19 upstream. Add USB ID for cp2104/5 devices on GE B650v3 and B850v3 boards. Signed-off-by:
Ken Lin <ken.lin@advantech.com.tw> Signed-off-by:
Akshay Bhat <akshay.bhat@timesys.com> Signed-off-by:
-
Gerhard Uttenthaler authored
commit 90cfde46 upstream. This patch fixes the problem that more CAN messages could be sent to the interface as could be send on the CAN bus. This was more likely for slow baud rates. The sleeping _start_xmit was woken up in the _write_bulk_callback. Under heavy TX load this produced another bulk transfer without checking the free_slots variable and hence caused the overflow in the interface. Signed-off-by:
Gerhard Uttenthaler <uttenthaler@ems-wuensche.com> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Nikolay Borisov authored
commit 18d03e8c upstream. When a thin pool is being destroyed delayed work items are cancelled using cancel_delayed_work(), which doesn't guarantee that on return the delayed item isn't running. This can cause the work item to requeue itself on an already destroyed workqueue. Fix this by using cancel_delayed_work_sync() which guarantees that on return the work item is not running anymore. Fixes: 905e51b3 ("dm thin: commit outstanding data every second") Fixes: 85ad643b ("dm thin: add timeout to stop out-of-data-space mode holding IO forever") Signed-off-by:
Nikolay Borisov <kernel@kyup.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Joe Thornber authored
commit 49e99fc7 upstream. When you take a metadata snapshot the btree roots for the mapping and details tree need to have their reference counts incremented so they persist for the lifetime of the metadata snap. The roots being incremented were those currently written in the superblock, which could possibly be out of date if concurrent IO is triggering new mappings, breaking of sharing, etc. Fix this by performing a commit with the metadata lock held while taking a metadata snapshot. Signed-off-by:
Joe Thornber <ejt@redhat.com> Signed-off-by:
-
Mike Snitzer authored
commit 172c2386 upstream. A thin-pool that is in out-of-data-space (OODS) mode may transition back to write mode -- without the admin adding more space to the thin-pool -- if/when blocks are released (either by deleting thin devices or discarding provisioned blocks). But as part of the thin-pool's earlier transition to out-of-data-space mode the thin-pool may have set the 'error_if_no_space' flag to true if the no_space_timeout expires without more space having been made available. That implementation detail, of changing the pool's error_if_no_space setting, needs to be reset back to the default that the user specified when the thin-pool's table was loaded. Otherwise we'll drop the user requested behaviour on the floor when this out-of-data-space to write mode transition occurs. Reported-by:
Vivek Goyal <vgoyal@redhat.com> Signed-off-by:
-
Ingo Molnar authored
commit 23a0d4e8 upstream. Tapasweni Pathak reported that we do a kmalloc() in efi_call_phys_prolog() on x86-64 while having interrupts disabled, which is a big no-no, as kmalloc() can sleep. Solve this by removing the irq disabling from the prolog/epilog calls around EFI calls: it's unnecessary, as in this stage we are single threaded in the boot thread, and we don't ever execute this from interrupt contexts. Reported-by:
Tapasweni Pathak <tapaswenipathak@gmail.com> Signed-off-by:
Matt Fleming <matt.fleming@intel.com> Signed-off-by:
-
Dave Airlie authored
commit 7f98ca45 upstream. We apparantly get a hotplug irq before we've initialised modesetting, [drm] Loading R100 Microcode BUG: unable to handle kernel NULL pointer dereference at (null) IP: [<c125f56f>] __mutex_lock_slowpath+0x23/0x91 *pde = 00000000 Oops: 0002 [#1] Modules linked in: radeon(+) drm_kms_helper ttm drm i2c_algo_bit backlight pcspkr psmouse evdev sr_mod input_leds led_class cdrom sg parport_pc parport floppy intel_agp intel_gtt lpc_ich acpi_cpufreq processor button mfd_core agpgart uhci_hcd ehci_hcd rng_core snd_intel8x0 snd_ac97_codec ac97_bus snd_pcm usbcore usb_common i2c_i801 i2c_core snd_timer snd soundcore thermal_sys CPU: 0 PID: 15 Comm: kworker/0:1 Not tainted 4.2.0-rc7-00015-gbf674028 #111 Hardware name: MicroLink /D850MV , BIOS MV85010A.86A.0067.P24.0304081124 04/08/2003 Workqueue: events radeon_hotplug_work_func [radeon] task: f6ca5900 ti: f6d3e000 task.ti: f6d3e000 EIP: 0060:[<c125f56f>] EFLAGS: 00010282 CPU: 0 EIP is at __mutex_lock_slowpath+0x23/0x91 EAX: 00000000 EBX: f5e900fc ECX: 00000000 EDX: fffffffe ESI: f6ca5900 EDI: f5e90100 EBP: f5e90000 ESP: f6d3ff0c DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068 CR0: 8005003b CR2: 00000000 CR3: 36f61000 CR4: 000006d0 Stack: f5e90100 00000000 c103c4c1 f6d2a5a0 f5e900fc f6df394c c125f162 f8b0faca f6d2a5a0 c138ca00 f6df394c f7395600 c1034741 00d40000 00000000 f6d2a5a0 c138ca00 f6d2a5b8 c138ca10 c1034b58 00000001 f6d40000 f6ca5900 f6d0c940 Call Trace: [<c103c4c1>] ? dequeue_task_fair+0xa4/0xb7 [<c125f162>] ? mutex_lock+0x9/0xa [<f8b0faca>] ? radeon_hotplug_work_func+0x17/0x57 [radeon] [<c1034741>] ? process_one_work+0xfc/0x194 [<c1034b58>] ? worker_thread+0x18d/0x218 [<c10349cb>] ? rescuer_thread+0x1d5/0x1d5 [<c103742a>] ? kthread+0x7b/0x80 [<c12601c0>] ? ret_from_kernel_thread+0x20/0x30 [<c10373af>] ? init_completion+0x18/0x18 Code: 42 08 e8 8e a6 dd ff c3 57 56 53 83 ec 0c 8b 35 48 f7 37 c1 8b 10 4a 74 1a 89 c3 8d 78 04 8b 40 08 89 63 Reported-and-Tested-by:
Meelis Roos <mroos@linux.ee> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
