- 23 Nov, 2022 40 commits
-
-
Antoniu Miclaus authored
Add device tree bindings for the ADF4377 driver. Signed-off-by:
Antoniu Miclaus <antoniu.miclaus@analog.com> Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20221115110041.71495-1-antoniu.miclaus@analog.comSigned-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Cosmin Tanislav authored
Reference the "spi-peripheral-props.yaml" schema to allow using all SPI device properties. Signed-off-by:
Cosmin Tanislav <cosmin.tanislav@analog.com> Acked-by:
Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20221115151955.394030-1-cosmin.tanislav@analog.comSigned-off-by:
-
Cosmin Tanislav authored
Currently there are -nanoamp properties both with and without a $ref. dt-schema has been modified to handle it as a standard unit, but the change has been reverted since there were still occurrences of -nanoamp properties with a $ref. Remove this since it's the only occurrence left. Signed-off-by:
-
Lad Prabhakar authored
The ADC block on the RZ/Five SoC is identical to one found on the RZ/G2UL SoC. "renesas,r9a07g043-adc" compatible string will be used on the RZ/Five SoC so to make this clear, update the comment to include RZ/Five SoC. No driver changes are required as generic compatible string "renesas,rzg2l-adc" will be used as a fallback on RZ/Five SoC. Signed-off-by:
Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Acked-by:
Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20221115124128.1183144-1-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by:
-
Rasmus Villemoes authored
Prior to commit bd5d54e4 ("iio: adc128s052: add ACPI _HID AANT1280"), the driver unconditionally used spi_get_device_id() to get the index into the adc128_config array. However, with that commit, OF-based boards now incorrectly treat all supported sensors as if they are an adc128s052, because all the .data members of the adc128_of_match table are implicitly 0. Our board, which has an adc122s021, thus exposes 8 channels whereas it really only has two. Fixes: bd5d54e4 ("iio: adc128s052: add ACPI _HID AANT1280") Signed-off-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20221115132324.1078169-1-linux@rasmusvillemoes.dk Cc: <Stable@vger.kernel.org> Signed-off-by:
-
Olivier Moysan authored
Add debugfs to read linear ADC STM32 self calibration results. Signed-off-by:
Fabrice Gasnier <fabrice.gasnier@foss.st.com> Signed-off-by:
Olivier Moysan <olivier.moysan@foss.st.com> Reviewed-by:
-
Olivier Moysan authored
Add more information in calibration error log to differentiate single-ended and differential calibration. Signed-off-by:
-
Olivier Moysan authored
Add smart calibration support for STM32MP1. - STM32MP15x: both linear & offset calibration are supported - STM32MP13x: Only offset calibration is supported Linear calibration: Linear calibration is SoC dependent and does not change over time so it can be done only once. Linear calibration may have already been done in u-boot. Skip calibration execution if calibration data are already available. Save calibration factors in private data and restore them from private data on next ADC start. Offset calibration: This calibration may vary over time, depending on temperature or voltage. Run offset single-ended and differential calibration on each ADC start, as it is not time consuming. This calibration do not need to be saved. So, remove calfact_s and calfact_d value and bitfields that are no longer used. Signed-off-by:
-
Rasmus Villemoes authored
We have a board where the reset pin of the ad74412 is connected to a gpio, but also pulled low (i.e., asserted) by default. Hence to get the chip out of reset, the driver needs to know about that gpio and deassert the reset signal before attempting to communicate with the chip. When a reset-gpio is given in device tree, use that instead of the software reset. According to the data sheet, the two methods are functionally equivalent. Signed-off-by:
-
Rasmus Villemoes authored
The ad74412 and ad74413 devices have an active-low reset pin. Add a binding allowing one to specify a gpio tied to that. Signed-off-by:
-
Rasmus Villemoes authored
Silence the run-time warning SPI driver ad74413r has no spi_device_id for adi,ad74412r Signed-off-by:
-
Luca Weiss authored
As in other bindings, let's use specific compatibles together with the fallback compatible. Adjust the bindings for it. Signed-off-by:
Luca Weiss <luca@z3ntu.xyz> Acked-by:
-
Lorenzo Bianconi authored
Add device bindings for lsm6dso16is IMU sensor. Signed-off-by:
Lorenzo Bianconi <lorenzo@kernel.org> Acked-by:
-
Lorenzo Bianconi authored
Add support to STM LSM6DSO16IS (accelerometer and gyroscope) Mems sensor. Datasheet: https://www.st.com/resource/en/datasheet/lsm6dso16is.pdfTested-by:
Mario Tesi <mario.tesi@st.com> Signed-off-by:
-
Cosmin Tanislav authored
The AD74115H is a single-channel, software-configurable, input and output device for industrial control applications. The AD74115H provides a wide range of use cases, integrated on a single chip. These use cases include analog output, analog input, digital output, digital input, resistance temperature detector (RTD), and thermocouple measurement capability. The AD74115H also has an integrated HART modem. A serial peripheral interface (SPI) is used to handle all communications to the device, including communications with the HART modem. The digital input and digital outputs can be accessed via the SPI or the general-purpose input and output (GPIO) pins to support higher speed data rates. The device features a 16-bit, sigma-delta analog-to-digital converter (ADC) and a 14-bit digital-to-analog converter (DAC). The AD74115H contains a high accuracy 2.5 V on-chip reference that can be used as the DAC and ADC reference. Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20221117080916.411766-3-cosmin.tanislav@analog.comSigned-off-by:
-
Cosmin Tanislav authored
The AD74115H is a single-channel, software-configurable, input and output device for industrial control applications. The AD74115H provides a wide range of use cases, integrated on a single chip. These use cases include analog output, analog input, digital output, digital input, resistance temperature detector (RTD), and thermocouple measurement capability. The AD74115H also has an integrated HART modem. A serial peripheral interface (SPI) is used to handle all communications to the device, including communications with the HART modem. The digital input and digital outputs can be accessed via the SPI or the general-purpose input and output (GPIO) pins to support higher speed data rates. The device features a 16-bit, sigma-delta analog-to-digital converter (ADC) and a 14-bit digital-to-analog converter (DAC). The AD74115H contains a high accuracy 2.5 V on-chip reference that can be used as the DAC and ADC reference. Signed-off-by:
-
Rasmus Villemoes authored
The constant AD74413R_ADC_RESULT_MAX is defined via GENMASK, so its type is "unsigned long". Hence in the expression voltage_offset * AD74413R_ADC_RESULT_MAX, voltage_offset is first promoted to unsigned long, and since it may be negative, that results in a garbage value. For example, when range is AD74413R_ADC_RANGE_5V_BI_DIR, voltage_offset is -2500 and voltage_range is 5000, so the RHS of this assignment is, depending on sizeof(long), either 826225UL or 3689348814709142UL, which after truncation to int then results in either 826225 or 1972216214 being the output from in_currentX_offset. Casting to int avoids that promotion and results in the correct -32767 output. Signed-off-by:
Nuno Sá <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20221118123209.1658420-1-linux@rasmusvillemoes.dk Cc: <Stable@vger.kernel.org> Signed-off-by:
-
Minghao Chi authored
Convert platform_get_resource(), devm_ioremap_resource() to a single call to devm_platform_get_and_ioremap_resource(), as this is exactly what this function does. Signed-off-by:
Minghao Chi <chi.minghao@zte.com.cn> Signed-off-by:
ye xingchen <ye.xingchen@zte.com.cn> Reviewed-by:
-
Ramona Bolboaca authored
Remove adis_initial_startup function since it is not used anymore. Signed-off-by:
Ramona Bolboaca <ramona.bolboaca@analog.com> Reviewed-by:
-
Ramona Bolboaca authored
Call '__adis_initial_startup()' instead of its locked variant in 'adis16240_probe()'. The locks are not needed at this point. Signed-off-by:
-
Ramona Bolboaca authored
Call '__adis_initial_startup()' instead of its locked variant in 'adis16203_probe()'. The locks are not needed at this point. Signed-off-by:
-
Ramona Bolboaca authored
Call '__adis_initial_startup()' instead of its locked variant in 'adis16400_probe()'. The locks are not needed at this point. Signed-off-by:
-
Ramona Bolboaca authored
Call '__adis_initial_startup()' instead of its locked variant in 'adis16260_probe()'. The locks are not needed at this point. Signed-off-by:
-
Ramona Bolboaca authored
Call '__adis_initial_startup()' instead of its locked variant in 'adis16136_probe()'. The locks are not needed at this point. Signed-off-by:
-
Ramona Bolboaca authored
Call '__adis_initial_startup()' instead of its locked variant in 'adis16209_probe()'. The locks are not needed at this point. Signed-off-by:
-
Ramona Bolboaca authored
Call '__adis_initial_startup()' instead of its locked variant in 'adis16201_probe()'. The locks are not needed at this point. Signed-off-by:
-
Ramona Bolboaca authored
Add '__adis_enable_irq()' implementation which is the unlocked version of 'adis_enable_irq()'. Call '__adis_enable_irq()' instead of 'adis_enable_irq()' from '__adis_intial_startup()' to keep the expected unlocked functionality. This fix is needed to remove a deadlock for all devices which are using 'adis_initial_startup()'. The deadlock occurs because the same mutex is acquired twice, without releasing it. The mutex is acquired once inside 'adis_initial_startup()', before calling '__adis_initial_startup()', and once inside 'adis_enable_irq()', which is called by '__adis_initial_startup()'. The deadlock is removed by calling '__adis_enable_irq()', instead of 'adis_enable_irq()' from within '__adis_initial_startup()'. Fixes: b600bd7e ("iio: adis: do not disabe IRQs in 'adis_init()'") Signed-off-by:
-
Ibrahim Tilki authored
VREFP bit was missing from channel configuration mask and VREFN bit was included twice instead which fails to enable positive reference buffer when requested by a channel. Channels that don't enable vrefp buffer were not affected. Fixes: a44ef7c4 ("iio: adc: add max11410 adc driver") Reported-by:
kernel test robot <lkp@intel.com> Reported-by:
Julia Lawall <julia.lawall@lip6.fr> Signed-off-by:
Ibrahim Tilki <Ibrahim.Tilki@analog.com> Link: https://lore.kernel.org/r/20221122114718.17557-1-Ibrahim.Tilki@analog.comSigned-off-by:
-
Edmund Berenson authored
- The ad7927 is fully compatible with ad7928 driver, add documentation for device. - ad7923 and ad7924 are treated the same in the driver, show the relationship in the documentation. Suggested-by:
Lukasz Zemla <Lukasz.Zemla@woodward.com> Signed-off-by:
Edmund Berenson <edmund.berenson@emlix.com> Reviewed-by:
-
Rajat Khandelwal authored
Maxim MAX30208 is a digital temperature sensor with 0.1°C accuracy. Add support for max30208 driver in iio subsystem. Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX30208.pdfSigned-off-by:
Rajat Khandelwal <rajat.khandelwal@linux.intel.com> Link: https://lore.kernel.org/r/20221122175300.800956-1-rajat.khandelwal@linux.intel.comSigned-off-by:
-
Uwe Kleine-König authored
The probe function doesn't make use of the i2c_device_id * parameter so it can be trivially converted. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20221118224540.619276-569-uwe@kleine-koenig.orgSigned-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
The probe function doesn't make use of the i2c_device_id * parameter so it can be trivially converted. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
The probe function doesn't make use of the i2c_device_id * parameter so it can be trivially converted. Signed-off-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
Crt Mori <cmo@melexis.com> Reviewed-by:
-
Uwe Kleine-König authored
.probe_new() doesn't get the i2c_device_id * parameter, so determine that explicitly in the probe function. Signed-off-by:
-
Uwe Kleine-König authored
The probe function doesn't make use of the i2c_device_id * parameter so it can be trivially converted. Signed-off-by:
-
