No users left in the kernel, it can be removed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200828084141.14902-1-peter.ujfalusi@ti.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Starting with core version 4.3.a the DMA bus attributes can (and should) be
read from the INTERFACE_DESCRIPTION (0x10) register.

For older core versions, this will still need to be provided from the
device-tree.

The bus-type values are identical to the ones stored in the device-trees,
so we just need to read them. Bus-width values are stored in log2 values,
so we just need to use them as shift values to make them equivalent to the
current format.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20200825151950.57605-7-alexandru.ardelean@analog.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The channel parameters (which are read from the device-tree) are adjusted
for the DMAEngine framework in the axi_dmac_parse_chan_dt() function, after
they are read from the device-tree.

When we want to read these from registers, we will need to use the same
logic, so this change splits the logic into a separate function.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20200825151950.57605-6-alexandru.ardelean@analog.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

All these attributes will be read from registers in newer core versions, so
just wrap the logic into a function.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20200825151950.57605-5-alexandru.ardelean@analog.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The clock may also be required to read registers from the IP core (if it is
provided and the driver needs to control it).
So, move it earlier in the probe.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20200825151950.57605-4-alexandru.ardelean@analog.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

We want to enable the clock right after it is obtained. Then later we'll
want to read the core version via register-access (which requires the clock
to be enabled).

The initialization of the active_descs list can be postponed after reading
from registers (or reading the device-tree).
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20200825151950.57605-3-alexandru.ardelean@analog.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The 'version' of the IP core will be needed to adapt the driver to a new
feature (i.e. reading some DMA parameters from registers).
To do that, the version will be checked, so this is being moved out of the
axi_dmac_detect_caps() function.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20200825151950.57605-2-alexandru.ardelean@analog.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Instruction dump uses two printk() in a row to print one instruction. Use
KERN_CONT to prevent breaking the output in the middle.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Link: https://lore.kernel.org/r/20200813204123.19044-1-l.stelmach@samsung.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Fix typo in comments offset related to padding bytes.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Link: https://lore.kernel.org/r/d7c7e56a83a13a62438a6c1a23863015a3760581.1597327654.git.gustavo.pimentel@synopsys.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The direction has been already validated in the main callback and there is
no need to check it again in the TR mode handlers for slave_sg and cyclic.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200824120120.9270-1-peter.ujfalusi@ti.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The sparse tool complains as follows:

drivers/dma/xilinx/xilinx_dpdma.c:349:37: warning:
 symbol 'dpdma_debugfs_reqs' was not declared. Should it be static?

This variable is not used outside of xilinx_dpdma.c, so this commit
marks it static.

Fixes: 1d220435 ("dmaengine: xilinx: dpdma: Add debugfs support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Hyun Kwon <hyun.kwon@xilinx.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200818112217.43816-1-weiyongjun1@huawei.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

DW DMA IP-core provides a way to synthesize the DMA controller with
channels having different parameters like maximum burst-length,
multi-block support, maximum data width, etc. Those parameters both
explicitly and implicitly affect the channels performance. Since DMA slave
devices might be very demanding to the DMA performance, let's provide a
functionality for the slaves to be assigned with DW DMA channels, which
performance according to the platform engineer fulfill their requirements.
After this patch is applied it can be done by passing the mask of suitable
DMA-channels either directly in the dw_dma_slave structure instance or as
a fifth cell of the DMA DT-property. If mask is zero or not provided, then
there is no limitation on the channels allocation.

For instance Baikal-T1 SoC is equipped with a DW DMAC engine, which first
two channels are synthesized with max burst length of 16, while the rest
of the channels have been created with max-burst-len=4. It would seem that
the first two channels must be faster than the others and should be more
preferable for the time-critical DMA slave devices. In practice it turned
out that the situation is quite the opposite. The channels with
max-burst-len=4 demonstrated a better performance than the channels with
max-burst-len=16 even when they both had been initialized with the same
settings. The performance drop of the first two DMA-channels made them
unsuitable for the DW APB SSI slave device. No matter what settings they
are configured with, full-duplex SPI transfers occasionally experience the
Rx FIFO overflow. It means that the DMA-engine doesn't keep up with
incoming data pace even though the SPI-bus is enabled with speed of 25MHz
while the DW DMA controller is clocked with 50MHz signal. There is no such
problem has been noticed for the channels synthesized with
max-burst-len=4.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200731200826.9292-6-Sergey.Semin@baikalelectronics.ruSigned-off-by: Vinod Koul <vkoul@kernel.org>

According to the DW DMA controller Databook 2.18b (page 40 "3.5 Memory
Peripherals") memory peripherals don't have handshaking interface
connected to the controller, therefore they can never be a flow
controller. Since the CTLx.SRC_MSIZE and CTLx.DEST_MSIZE are properties
valid only for peripherals with a handshaking interface, we can freely
zero these fields out if the memory peripheral is selected to be the
source or the destination of the DMA transfers.

Note according to the databook, length of burst transfers to memory is
always equal to the number of data items available in a channel FIFO or
data items required to complete the block transfer, whichever is smaller;
length of burst transfers from memory is always equal to the space
available in a channel FIFO or number of data items required to complete
the block transfer, whichever is smaller.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200731200826.9292-5-Sergey.Semin@baikalelectronics.ruSigned-off-by: Vinod Koul <vkoul@kernel.org>

Indeed in case of the DMA_DEV_TO_MEM DMA transfers it's enough to take the
destination memory address and the destination master data width into
account to calculate the CTLx.DST_TR_WIDTH setting of the memory
peripheral. According to the DW DMAC IP-core Databook 2.18b (page 66,
Example 5) at the and of a DMA transfer when the DMA-channel internal FIFO
is left with data less than for a single destination burst transaction,
the destination peripheral will enter the Single Transaction Region where
the DW DMA controller can complete a block transfer to the destination
using single transactions (non-burst transaction of CTLx.DST_TR_WIDTH
bytes). If there is no enough data in the DMA-channel internal FIFO for
even a single non-burst transaction of CTLx.DST_TR_WIDTH bytes, then the
channel enters "FIFO flush mode". That mode is activated to empty the FIFO
and flush the leftovers out to the memory peripheral. The flushing
procedure is simple.  The data is sent to the memory by means of a set of
single transaction of CTLx.SRC_TR_WIDTH bytes. To sum up it's redundant to
use the LLPs length to find out the CTLx.DST_TR_WIDTH parameter value,
since each DMA transfer will be completed with the CTLx.SRC_TR_WIDTH bytes
transaction if it is required.

We suggest to remove the LLP entry length from the statement which
calculates the memory peripheral DMA transaction width since it's
redundant due to the feature described above. By doing so we'll improve
the memory bus utilization and speed up the DMA-channel performance for
DMA_DEV_TO_MEM DMA-transfers.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200731200826.9292-4-Sergey.Semin@baikalelectronics.ruSigned-off-by: Vinod Koul <vkoul@kernel.org>

CFGx.FIFO_MODE field controls a DMA-controller "FIFO readiness" criterion.
In other words it determines when to start pushing data out of a DW
DMAC channel FIFO to a destination peripheral or from a source
peripheral to the DW DMAC channel FIFO. Currently FIFO-mode is set to one
for all DW DMAC channels. It means they are tuned to flush data out of
FIFO (to a memory peripheral or by accepting the burst transaction
requests) when FIFO is at least half-full (except at the end of the block
transfer, when FIFO-flush mode is activated) and are configured to get
data to the FIFO when it's at least half-empty.

Such configuration is a good choice when there is no slave device involved
in the DMA transfers. In that case the number of bursts per block is less
than when CFGx.FIFO_MODE = 0 and, hence, the bus utilization will improve.
But the latency of DMA transfers may increase when CFGx.FIFO_MODE = 1,
since DW DMAC will wait for the channel FIFO contents to be either
half-full or half-empty depending on having the destination or the source
transfers. Such latencies might be dangerous in case if the DMA transfers
are expected to be performed from/to a slave device. Since normally
peripheral devices keep data in internal FIFOs, any latency at some
critical moment may cause one being overflown and consequently losing
data. This especially concerns a case when either a peripheral device is
relatively fast or the DW DMAC engine is relatively slow with respect to
the incoming data pace.

In order to solve problems, which might be caused by the latencies
described above, let's enable the FIFO half-full/half-empty "FIFO
readiness" criterion only for DMA transfers with no slave device involved.
Thanks to the commit 99ba8b9b ("dmaengine: dw: Initialize channel
before each transfer") we can freely do that in the generic
dw_dma_initialize_chan() method.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200731200826.9292-3-Sergey.Semin@baikalelectronics.ruSigned-off-by: Vinod Koul <vkoul@kernel.org>

Each DW DMA controller channel can be synthesized with different
parameters like maximum burst-length, multi-block support, maximum data
width, etc. Most of these parameters determine the DW DMAC channels
performance in its own aspect. On the other hand these parameters can
be implicitly responsible for the channels performance degradation
(for instance multi-block support is a very useful feature, but having
it disabled during the DW DMAC synthesize will provide a more optimized
core). Since DMA slave devices may have critical dependency on the DMA
engine performance, let's provide a way for the slave devices to have
the DMA-channels allocated from a pool of the channels, which according
to the system engineer fulfill their performance requirements.

The pool is determined by a mask optionally specified in the fifth
DMA-cell of the DMA DT-property. If the fifth cell is omitted from the
phandle arguments or the mask is zero, then the allocation will be
performed from a set of all channels provided by the DMA controller.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200731200826.9292-2-Sergey.Semin@baikalelectronics.ruSigned-off-by: Vinod Koul <vkoul@kernel.org>

Expose statistics to debugfs when available. This helps debugging issues
with the DPDMA driver.
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200812171228.9751-1-laurent.pinchart@ideasonboard.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The security accelerator within MCU domain supports two ports similarly
to the SA2UL in MAIN domain.

Add endpoint configuration for the two ingress and one egress threads of
the second port.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200803100724.19003-1-peter.ujfalusi@ti.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Add new PSI-L map file for the new TI j7200 SoC.

The DMA hardware in j7200 is the same as in j721e with different
set of peripherals resulting different PSI-L thread map compered
to j721e.

See J7200 Technical Reference Manual (SPRUIU1, June 2020)
for further details: https://www.ti.com/lit/pdf/spruiu1Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200803125713.17829-3-peter.ujfalusi@ti.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Instead of separate of_machine_is_compatible() it is better to use
soc_device_match() and soc_device_attribute struct to get the PSI-L map
for the booted device.

By using soc_device_match() it is easier to add support for new devices.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200803125713.17829-2-peter.ujfalusi@ti.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Move the clearing of misc interrupt cause to immediately after reading the
register in order to allow the next interrupt to be asserted.
Suggested-by: Nikhil Rao <nikhil.rao@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/159603824665.28647.5344356370364397996.stgit@djiang5-desk3.ch.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

The of_device_id is included unconditionally by of.h header and used
in the driver as well.  Remove of_match_ptr to fix W=1 compile test
warning with !CONFIG_OF:

    drivers/dma/ti/omap-dma.c:1892:34: warning: 'omap_dma_match' defined but not used [-Wunused-const-variable=]
     1892 | static const struct of_device_id omap_dma_match[] = {
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200728170939.28278-1-krzk@kernel.orgSigned-off-by: Vinod Koul <vkoul@kernel.org>

Drivers using legacy PM have to manage PCI states and device's PM states
themselves. They also need to take care of configuration registers.

With improved and powerful support of generic PM, PCI Core takes care of
above mentioned, device-independent, jobs.

This driver makes use of PCI helper functions like
pci_save/restore_state(), pci_enable/disable_device(),
and pci_set_power_state() to do required operations. In generic mode, they
are no longer needed.

Change function parameter in both .suspend() and .resume() to
"struct device*" type. Use dev_get_drvdata() to get drv data.

Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200720113740.353479-1-vaibhavgupta40@gmail.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

Pull io_uring fixes from Jens Axboe:
 "A few differerent things in here.

  Seems like syzbot got some more io_uring bits wired up, and we got a
  handful of reports and the associated fixes are in here.

  General fixes too, and a lot of them marked for stable.

  Lastly, a bit of fallout from the async buffered reads, where we now
  more easily trigger short reads. Some applications don't really like
  that, so the io_read() code now handles short reads internally, and
  got a cleanup along the way so that it's now easier to read (and
  documented). We're now passing tests that failed before"

* tag 'io_uring-5.9-2020-08-15' of git://git.kernel.dk/linux-block:
  io_uring: short circuit -EAGAIN for blocking read attempt
  io_uring: sanitize double poll handling
  io_uring: internally retry short reads
  io_uring: retain iov_iter state over io_read/io_write calls
  task_work: only grab task signal lock when needed
  io_uring: enable lookup of links holding inflight files
  io_uring: fail poll arm on queue proc failure
  io_uring: hold 'ctx' reference around task_work queue + execute
  fs: RWF_NOWAIT should imply IOCB_NOIO
  io_uring: defer file table grabbing request cleanup for locked requests
  io_uring: add missing REQ_F_COMP_LOCKED for nested requests
  io_uring: fix recursive completion locking on oveflow flush
  io_uring: use TWA_SIGNAL for task_work uncondtionally
  io_uring: account locked memory before potential error case
  io_uring: set ctx sq/cq entry count earlier
  io_uring: Fix NULL pointer dereference in loop_rw_iter()
  io_uring: add comments on how the async buffered read retry works
  io_uring: io_async_buf_func() need not test page bit

Commit 1355c31e ("asm-generic: pgalloc: provide generic pmd_alloc_one()
and pmd_free_one()") converted parisc to use generic version of
pmd_alloc_one() but it missed the fact that parisc uses order-1 pages for
PMD.

Restore the original version of pmd_alloc_one() for parisc, just use
GFP_PGTABLE_KERNEL that implies __GFP_ZERO instead of GFP_KERNEL and
memset.

Fixes: 1355c31e ("asm-generic: pgalloc: provide generic pmd_alloc_one() and pmd_free_one()")
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Meelis Roos <mroos@linux.ee>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Link: https://lkml.kernel.org/r/9f2b5ebd-e4a4-0fa1-6cd3-4b9f6892d1ad@linux.eeSigned-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull block fixes from Jens Axboe:
 "A few fixes on the block side of things:

   - Discard granularity fix (Coly)

   - rnbd cleanups (Guoqing)

   - md error handling fix (Dan)

   - md sysfs fix (Junxiao)

   - Fix flush request accounting, which caused an IO slowdown for some
     configurations (Ming)

   - Properly propagate loop flag for partition scanning (Lennart)"

* tag 'block-5.9-2020-08-14' of git://git.kernel.dk/linux-block:
  block: fix double account of flush request's driver tag
  loop: unset GENHD_FL_NO_PART_SCAN on LOOP_CONFIGURE
  rnbd: no need to set bi_end_io in rnbd_bio_map_kern
  rnbd: remove rnbd_dev_submit_io
  md-cluster: Fix potential error pointer dereference in resize_bitmaps()
  block: check queue's limits.discard_granularity in __blkdev_issue_discard()
  md: get sysfs entry after redundancy attr group create

Pull RISC-V fix from Palmer Dabbelt:
 "I collected a single fix during the merge window: we managed to break
  the early trap setup on !MMU, this fixes it"

* tag 'riscv-for-linus-5.9-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: Setup exception vector for nommu platform

Pull arch/sh updates from Rich Felker:
 "Cleanup, SECCOMP_FILTER support, message printing fixes, and other
  changes to arch/sh"

* tag 'sh-for-5.9' of git://git.libc.org/linux-sh: (34 commits)
  sh: landisk: Add missing initialization of sh_io_port_base
  sh: bring syscall_set_return_value in line with other architectures
  sh: Add SECCOMP_FILTER
  sh: Rearrange blocks in entry-common.S
  sh: switch to copy_thread_tls()
  sh: use the generic dma coherent remap allocator
  sh: don't allow non-coherent DMA for NOMMU
  dma-mapping: consolidate the NO_DMA definition in kernel/dma/Kconfig
  sh: unexport register_trapped_io and match_trapped_io_handler
  sh: don't include <asm/io_trapped.h> in <asm/io.h>
  sh: move the ioremap implementation out of line
  sh: move ioremap_fixed details out of <asm/io.h>
  sh: remove __KERNEL__ ifdefs from non-UAPI headers
  sh: sort the selects for SUPERH alphabetically
  sh: remove -Werror from Makefiles
  sh: Replace HTTP links with HTTPS ones
  arch/sh/configs: remove obsolete CONFIG_SOC_CAMERA*
  sh: stacktrace: Remove stacktrace_ops.stack()
  sh: machvec: Modernize printing of kernel messages
  sh: pci: Modernize printing of kernel messages
  ...

One case was missed in the short IO retry handling, and that's hitting
-EAGAIN on a blocking attempt read (eg from io-wq context). This is a
problem on sockets that are marked as non-blocking when created, they
don't carry any REQ_F_NOWAIT information to help us terminate them
instead of perpetually retrying.

Fixes: 227c0c96 ("io_uring: internally retry short reads")
Signed-off-by: Jens Axboe <axboe@kernel.dk>

There's a bit of confusion on the matching pairs of poll vs double poll,
depending on if the request is a pure poll (IORING_OP_POLL_ADD) or
poll driven retry.

Add io_poll_get_double() that returns the double poll waitqueue, if any,
and io_poll_get_single() that returns the original poll waitqueue. With
that, remove the argument to io_poll_remove_double().

Finally ensure that wait->private is cleared once the double poll handler
has run, so that remove knows it's already been seen.

Cc: stable@vger.kernel.org # v5.8
Reported-by: syzbot+7f617d4a9369028b8a2c@syzkaller.appspotmail.com
Fixes: 18bceab1 ("io_uring: allow POLL_ADD with double poll_wait() users")
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pull more perf tools updates from Arnaldo Carvalho de Melo:
 "Fixes:
   - Fixes for 'perf bench numa'.

   - Always memset source before memcpy in 'perf bench mem'.

   - Quote CC and CXX for their arguments to fix build in environments
     using those variables to pass more than just the compiler names.

   - Fix module symbol processing, addressing regression detected via
     "perf test".

   - Allow multiple probes in record+script_probe_vfs_getname.sh 'perf
     test' entry.

  Improvements:
   - Add script to autogenerate socket family name id->string table from
     copy of kernel header, used so far in 'perf trace'.

   - 'perf ftrace' improvements to provide similar options for this
     utility so that one can go from 'perf record', 'perf trace', etc to
     'perf ftrace' just by changing the name of the subcommand.

   - Prefer new "sched:sched_waking" trace event when it exists in 'perf
     sched' post processing.

   - Update POWER9 metrics to utilize other metrics.

   - Fall back to querying debuginfod if debuginfo not found locally.

  Miscellaneous:
   - Sync various kvm headers with kernel sources"

* tag 'perf-tools-2020-08-14' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (40 commits)
  perf ftrace: Make option description initials all capital letters
  perf build-ids: Fall back to debuginfod query if debuginfo not found
  perf bench numa: Remove dead code in parse_nodes_opt()
  perf stat: Update POWER9 metrics to utilize other metrics
  perf ftrace: Add change log
  perf: ftrace: Add set_tracing_options() to set all trace options
  perf ftrace: Add option --tid to filter by thread id
  perf ftrace: Add option -D/--delay to delay tracing
  perf: ftrace: Allow set graph depth by '--graph-opts'
  perf ftrace: Add support for trace option tracing_thresh
  perf ftrace: Add option 'verbose' to show more info for graph tracer
  perf ftrace: Add support for tracing option 'irq-info'
  perf ftrace: Add support for trace option funcgraph-irqs
  perf ftrace: Add support for trace option sleep-time
  perf ftrace: Add support for tracing option 'func_stack_trace'
  perf tools: Add general function to parse sublevel options
  perf ftrace: Add option '--inherit' to trace children processes
  perf ftrace: Show trace column header
  perf ftrace: Add option '-m/--buffer-size' to set per-cpu buffer size
  perf ftrace: Factor out function write_tracing_file_int()
  ...

Pull x86 fixes from Ingo Molnar:
 "Misc fixes and small updates all around the place:

   - Fix mitigation state sysfs output

   - Fix an FPU xstate/sxave code assumption bug triggered by
     Architectural LBR support

   - Fix Lightning Mountain SoC TSC frequency enumeration bug

   - Fix kexec debug output

   - Fix kexec memory range assumption bug

   - Fix a boundary condition in the crash kernel code

   - Optimize porgatory.ro generation a bit

   - Enable ACRN guests to use X2APIC mode

   - Reduce a __text_poke() IRQs-off critical section for the benefit of
     PREEMPT_RT"

* tag 'x86-urgent-2020-08-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/alternatives: Acquire pte lock with interrupts enabled
  x86/bugs/multihit: Fix mitigation reporting when VMX is not in use
  x86/fpu/xstate: Fix an xstate size check warning with architectural LBRs
  x86/purgatory: Don't generate debug info for purgatory.ro
  x86/tsr: Fix tsc frequency enumeration bug on Lightning Mountain SoC
  kexec_file: Correctly output debugging information for the PT_LOAD ELF header
  kexec: Improve & fix crash_exclude_mem_range() to handle overlapping ranges
  x86/crash: Correct the address boundary of function parameters
  x86/acrn: Remove redundant chars from ACRN signature
  x86/acrn: Allow ACRN guest to use X2APIC mode

Pull scheduler fixes from Ingo Molnar:
 "Two fixes: fix a new tracepoint's output value, and fix the formatting
  of show-state syslog printouts"

* tag 'sched-urgent-2020-08-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/debug: Fix the alignment of the show-state debug output
  sched: Fix use of count for nr_running tracepoint

Pull perf fixes from Ingo Molnar:
 "Misc fixes, an expansion of perf syscall access to CAP_PERFMON
  privileged tools, plus a RAPL HW-enablement for Intel SPR platforms"

* tag 'perf-urgent-2020-08-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/rapl: Add support for Intel SPR platform
  perf/x86/rapl: Support multiple RAPL unit quirks
  perf/x86/rapl: Fix missing psys sysfs attributes
  hw_breakpoint: Remove unused __register_perf_hw_breakpoint() declaration
  kprobes: Remove show_registers() function prototype
  perf/core: Take over CAP_SYS_PTRACE creds to CAP_PERFMON capability

Pull locking fixlets from Ingo Molnar:
 "A documentation fix and a 'fallthrough' macro update"

* tag 'locking-urgent-2020-08-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  futex: Convert to use the preferred 'fallthrough' macro
  Documentation/locking/locktypes: Fix a typo

Pull 9p updates from Dominique Martinet:

 - some code cleanup

 - a couple of static analysis fixes

 - setattr: try to pick a fid associated with the file rather than the
   dentry, which might sometimes matter

* tag '9p-for-5.9-rc1' of git://github.com/martinetd/linux:
  9p: Remove unneeded cast from memory allocation
  9p: remove unused code in 9p
  net/9p: Fix sparse endian warning in trans_fd.c
  9p: Fix memory leak in v9fs_mount
  9p: retrieve fid from file when file instance exist.

Pull cifs fixes from Steve French:
 "Three small cifs/smb3 fixes, one for stable fixing mkdir path with
  the 'idsfromsid' mount option"

* tag '5.9-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  SMB3: Fix mkdir when idsfromsid configured on mount
  cifs: Convert to use the fallthrough macro
  cifs: Fix an error pointer dereference in cifs_mount()

Pull NFS client updates from Trond Myklebust:
 "Stable fixes:
   - pNFS: Don't return layout segments that are being used for I/O
   - pNFS: Don't move layout segments off the active list when being used for I/O

  Features:
   - NFS: Add support for user xattrs through the NFSv4.2 protocol
   - NFS: Allow applications to speed up readdir+statx() using AT_STATX_DONT_SYNC
   - NFSv4.0 allow nconnect for v4.0

  Bugfixes and cleanups:
   - nfs: ensure correct writeback errors are returned on close()
   - nfs: nfs_file_write() should check for writeback errors
   - nfs: Fix getxattr kernel panic and memory overflow
   - NFS: Fix the pNFS/flexfiles mirrored read failover code
   - SUNRPC: dont update timeout value on connection reset
   - freezer: Add unsafe versions of freezable_schedule_timeout_interruptible for NFS
   - sunrpc: destroy rpc_inode_cachep after unregister_filesystem"

* tag 'nfs-for-5.9-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (32 commits)
  NFS: Fix flexfiles read failover
  fs: nfs: delete repeated words in comments
  rpc_pipefs: convert comma to semicolon
  nfs: Fix getxattr kernel panic and memory overflow
  NFS: Don't return layout segments that are in use
  NFS: Don't move layouts to plh_return_segs list while in use
  NFS: Add layout segment info to pnfs read/write/commit tracepoints
  NFS: Add tracepoints for layouterror and layoutstats.
  NFS: Report the stateid + status in trace_nfs4_layoutreturn_on_close()
  SUNRPC dont update timeout value on connection reset
  nfs: nfs_file_write() should check for writeback errors
  nfs: ensure correct writeback errors are returned on close()
  NFSv4.2: xattr cache: get rid of cache discard work queue
  NFS: remove redundant initialization of variable result
  NFSv4.0 allow nconnect for v4.0
  freezer: Add unsafe versions of freezable_schedule_timeout_interruptible for NFS
  sunrpc: destroy rpc_inode_cachep after unregister_filesystem
  NFSv4.2: add client side xattr caching.
  NFSv4.2: hook in the user extended attribute handlers
  NFSv4.2: add the extended attribute proc functions.
  ...

Pull edac fix from Tony Luck:
 "Fix for the ie31200 driver that missed the first pull"

* tag 'edac_updates_for_5.9_pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
  EDAC/ie31200: Fallback if host bridge device is already initialized