- 03 Nov, 2014 6 commits
-
-
Ido Shamay authored
Needed in order to get cache cold pages (L3 flushed) for HW scatter. Otherwise memory may flush those entries when the packet comes from PCI, causing back pressure resulting in BW decrease. Signed-off-by: Ido Shamay <idos@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ido Shamay authored
When IP_ALIGN has a non zero value, hardware will write to a non aligned address. The only reader from this address is when copying the header from the first frag into the linear buffer (further access to the IP address will be from the linear buffer, in which the headers are aligned). Since the penalty of non align access by the hardware is greater than the software memcpy, changing the frag_align to always be 0. Signed-off-by: Ido Shamay <idos@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Amir Vadai authored
We need to protect set_port_type() for concurrency, as the sysfs code could call it from mutliple contexts in parallel. The port_mutex is not enough because we need to protect from concurrent modification of 'info' and stopping of the port sensing work. Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Saeed Mahameed authored
Added wrapper to the ACCESS_REG command for handling guest HW registers access, preventing write operations, but do allow reads. This will prevent SRIOV guests to change port PTYS configuration, such as speed/advertised link modes. Fixes: adbc7ac5 ('net/mlx4_core: Introduce ACCESS_REG CMD [...]') Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Amir Vadai <amirv@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
net_rx_action() can mask irqs a single time to transfert sd->poll_list into a private list, for a very short duration. Then, napi_complete() can avoid masking irqs again, and net_rx_action() only needs to mask irq again in slow path. This patch removes 2 couples of irq mask/unmask per typical NAPI run, more if multiple napi were triggered. Note this also allows to give control back to caller (do_softirq()) more often, so that other softirq handlers can be called a bit earlier, or ksoftirqd can be wakeup earlier under pressure. This was developed while testing an alternative to RX interrupt mitigation to reduce latencies while keeping or improving GRO aggregation on fast NIC. Idea is to test napi->gro_list at the end of a napi->poll() and reschedule one NAPI poll, but after servicing a full round of softirqs (timers, TX, rcu, ...). This will be allowed only if softirq is currently serviced by idle task or ksoftirqd, and resched not needed. Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
flow_limit in struct softnet_data is only read from local cpu and can be moved to fill a hole, reducing softnet_data size by 64 bytes on x86_64 While we are at it, move output_queue, output_queue_tailp and completion_queue, so that rx / tx paths touch a single cache line. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 01 Nov, 2014 6 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller authored
Conflicts: drivers/net/phy/marvell.c Simple overlapping changes in drivers/net/phy/marvell.c Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Reported-by: Meelis Roos <mroos@linux.ee> Tested-by: Meelis Roos <mroos@linux.ee> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/inputLinus Torvalds authored
Pull input updates from Dmitry Torokhov: "A bunch of fixes for minor defects reported by Coverity, a few driver fixups and revert of i8042.nomux change so that we are once again enable active MUX mode if box claims to support it" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Revert "Input: i8042 - disable active multiplexing by default" Input: altera_ps2 - use correct type for irq return value Input: altera_ps2 - write to correct register when disabling interrupts Input: max77693-haptic - fix potential overflow Input: psmouse - remove unneeded check in psmouse_reconnect() Input: vsxxxaa - fix code dropping bytes from queue Input: ims-pcu - fix dead code in ims_pcu_ofn_reg_addr_store() Input: opencores-kbd - fix error handling Input: wm97xx - adapt parameters to tosa touchscreen. Input: i8042 - quirks for Fujitsu Lifebook A544 and Lifebook AH544 Input: stmpe-keypad - fix valid key line bitmask Input: soc_button_array - update calls to gpiod_get*()
-
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pmLinus Torvalds authored
Pull ACPI and power management fixes from Rafael Wysocki: "These are fixes received after my previous pull request plus one that has been in the works for quite a while, but its previous version caused problems to happen, so it's been deferred till now. Fixed are two recent regressions (MFD enumeration and cpufreq-dt), ACPI EC regression introduced in 3.17, system suspend error code path regression introduced in 3.15, an older bug related to recovery from failing resume from hibernation and a cpufreq-dt driver issue related to operation performance points. Specifics: - Fix a crash on r8a7791/koelsch during resume from system suspend caused by a recent cpufreq-dt commit (Geert Uytterhoeven). - Fix an MFD enumeration problem introduced by a recent commit adding ACPI support to the MFD subsystem that exposed a weakness in the ACPI core causing ACPI enumeration to be applied to all devices associated with one ACPI companion object, although it should be used for one of them only (Mika Westerberg). - Fix an ACPI EC regression introduced during the 3.17 cycle causing some Samsung laptops to misbehave as a result of a workaround targeted at some Acer machines. That includes a revert of a commit that went too far and a quirk for the Acer machines in question. From Lv Zheng. - Fix a regression in the system suspend error code path introduced during the 3.15 cycle that causes it to fail to take errors from asychronous execution of "late" suspend callbacks into account (Imre Deak). - Fix a long-standing bug in the hibernation resume error code path that fails to roll back everything correcty on "freeze" callback errors and leaves some devices in a "suspended" state causing more breakage to happen subsequently (Imre Deak). - Make the cpufreq-dt driver disable operation performance points that are not supported by the VR connected to the CPU voltage plane with acceptable tolerance instead of constantly failing voltage scaling later on (Lucas Stach)" * tag 'pm+acpi-3.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: ACPI / EC: Fix regression due to conflicting firmware behavior between Samsung and Acer. Revert "ACPI / EC: Add support to disallow QR_EC to be issued before completing previous QR_EC" cpufreq: cpufreq-dt: Restore default cpumask_setall(policy->cpus) PM / Sleep: fix recovery during resuming from hibernation PM / Sleep: fix async suspend_late/freeze_late error handling ACPI: Use ACPI companion to match only the first physical device cpufreq: cpufreq-dt: disable unsupported OPPs
-
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pciLinus Torvalds authored
Pull PCI fixes from Bjorn Helgaas: "These changes, intended for v3.18, fix: Sysfs - Fix "enable" filename change (Greg Kroah-Hartman) An unintentional sysfs filename change in commit 5136b2da ("PCI: convert bus code to use dev_groups"), which appeared in v3.13, changed "enable" to "enabled", and this changes it back. Old users of "enable" are currently broken and will be helped by this change. Anything that started to use "enabled" after v3.13 will be broken by this change. If necessary, we can add a symlink to make both work, but this patch doesn't do that. PCI device hotplug - Revert duplicate merge (Kamal Mostafa) A mistaken duplicate merge that added a check twice. Nothing's broken; this just removes the unnecessary code. Freescale i.MX6 - Wait for clocks to stabilize after ref_en (Richard Zhu) An i.MX6 clock problem that prevents mx6 nitrogen boards from booting" * tag 'pci-v3.18-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: PCI: Rename sysfs 'enabled' file back to 'enable' PCI: imx6: Wait for clocks to stabilize after ref_en Revert duplicate "PCI: pciehp: Prevent NULL dereference during probe"
-
Andy Lutomirski authored
Rusty noticed a Really Bad Bug (tm) in my NT fix. The entry code reads out of bounds, causing the NT fix to be unreliable. But, and this is much, much worse, if your stack is somehow just below the top of the direct map (or a hole), you read out of bounds and crash. Excerpt from the crash: [ 1.129513] RSP: 0018:ffff88001da4bf88 EFLAGS: 00010296 2b:* f7 84 24 90 00 00 00 testl $0x4000,0x90(%rsp) That read is deterministically above the top of the stack. I thought I even single-stepped through this code when I wrote it to check the offset, but I clearly screwed it up. Fixes: 8c7aa698 ("x86_64, entry: Filter RFLAGS.NT on entry from userspace") Reported-by: Rusty Russell <rusty@ozlabs.org> Cc: stable@vger.kernel.org Signed-off-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
- 31 Oct, 2014 28 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4Linus Torvalds authored
Pull ext4 bugfixes from Ted Ts'o: "A set of miscellaneous ext4 bug fixes for 3.18" * tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: ext4: make ext4_ext_convert_to_initialized() return proper number of blocks ext4: bail early when clearing inode journal flag fails ext4: bail out from make_indexed_dir() on first error jbd2: use a better hash function for the revoke table ext4: prevent bugon on race between write/fcntl ext4: remove extent status procfs files if journal load fails ext4: disallow changing journal_csum option during remount ext4: enable journal checksum when metadata checksum feature enabled ext4: fix oops when loading block bitmap failed ext4: fix overflow when updating superblock backups after resize
-
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fsLinus Torvalds authored
Pull quota and ext3 fixes from Jan Kara. * 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs: fs, jbd: use a more generic hash function quota: Properly return errors from dquot_writeback_dquots() ext3: Don't check quota format when there are no quota files
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: "A bit has accumulated, but it's been a week or so since my last batch of post-merge-window fixes, so... 1) Missing module license in netfilter reject module, from Pablo. Lots of people ran into this. 2) Off by one in mac80211 baserate calculation, from Karl Beldan. 3) Fix incorrect return value from ax88179_178a driver's set_mac_addr op, which broke use of it with bonding. From Ian Morgan. 4) Checking of skb_gso_segment()'s return value was not all encompassing, it can return an SKB pointer, a pointer error, or NULL. Fix from Florian Westphal. This is crummy, and longer term will be fixed to just return error pointers or a real SKB. 6) Encapsulation offloads not being handled by skb_gso_transport_seglen(). From Florian Westphal. 7) Fix deadlock in TIPC stack, from Ying Xue. 8) Fix performance regression from using rhashtable for netlink sockets. The problem was the synchronize_net() invoked for every socket destroy. From Thomas Graf. 9) Fix bug in eBPF verifier, and remove the strong dependency of BPF on NET. From Alexei Starovoitov. 10) In qdisc_create(), use the correct interface to allocate ->cpu_bstats, otherwise the u64_stats_sync member isn't initialized properly. From Sabrina Dubroca. 11) Off by one in ip_set_nfnl_get_byindex(), from Dan Carpenter. 12) nf_tables_newchain() was erroneously expecting error pointers from netdev_alloc_pcpu_stats(). It only returna a valid pointer or NULL. From Sabrina Dubroca. 13) Fix use-after-free in _decode_session6(), from Li RongQing. 14) When we set the TX flow hash on a socket, we mistakenly do so before we've nailed down the final source port. Move the setting deeper to fix this. From Sathya Perla. 15) NAPI budget accounting in amd-xgbe driver was counting descriptors instead of full packets, fix from Thomas Lendacky. 16) Fix total_data_buflen calculation in hyperv driver, from Haiyang Zhang. 17) Fix bcma driver build with OF_ADDRESS disabled, from Hauke Mehrtens. 18) Fix mis-use of per-cpu memory in TCP md5 code. The problem is that something that ends up being vmalloc memory can't be passed to the crypto hash routines via scatter-gather lists. From Eric Dumazet. 19) Fix regression in promiscuous mode enabling in cdc-ether, from Olivier Blin. 20) Bucket eviction and frag entry killing can race with eachother, causing an unlink of the object from the wrong list. Fix from Nikolay Aleksandrov. 21) Missing initialization of spinlock in cxgb4 driver, from Anish Bhatt. 22) Do not cache ipv4 routing failures, otherwise if the sysctl for forwarding is subsequently enabled this won't be seen. From Nicolas Cavallari" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (131 commits) drivers: net: cpsw: Support ALLMULTI and fix IFF_PROMISC in switch mode drivers: net: cpsw: Fix broken loop condition in switch mode net: ethtool: Return -EOPNOTSUPP if user space tries to read EEPROM with lengh 0 stmmac: pci: set default of the filter bins net: smc91x: Fix gpios for device tree based booting mpls: Allow mpls_gso to be built as module mpls: Fix mpls_gso handler. r8152: stop submitting intr for -EPROTO netfilter: nft_reject_bridge: restrict reject to prerouting and input netfilter: nft_reject_bridge: don't use IP stack to reject traffic netfilter: nf_reject_ipv6: split nf_send_reset6() in smaller functions netfilter: nf_reject_ipv4: split nf_send_reset() in smaller functions netfilter: nf_tables_bridge: update hook_mask to allow {pre,post}routing drivers/net: macvtap and tun depend on INET drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packets drivers/net: Disable UFO through virtio net: skb_fclone_busy() needs to detect orphaned skb gre: Use inner mac length when computing tunnel length mlx4: Avoid leaking steering rules on flow creation error flow net/mlx4_en: Don't attempt to TX offload the outer UDP checksum for VXLAN ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparcLinus Torvalds authored
Pull sparc update from David Miller: "Two changes: 1) It makes no sense to execute a VTOC partition table request in the Sun virtual block device driver and fail to load if it doesn't succeed because a) we don't use the result at all and b) it won't succeed if there is an EFI partition on the disk, for example. We read the partition table via the normal means in the block layer anyways, so this is really completely useless, so just remove it. From Dwight Engen. 2) Hook up new bpf system call" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc: sunvdc: don't call VD_OP_GET_VTOC sparc: Hook up bpf system call.
-
git://git.monstr.eu/linux-2.6-microblazeLinus Torvalds authored
Pull Microblaze updates from Michal Simek: - wire-up new bpf syscall - fix PCI bug - fix Kconfig warning * tag 'microblaze-3.18-rc3' of git://git.monstr.eu/linux-2.6-microblaze: microblaze: Wire up bpf syscall microblaze: Fix IO space breakage after of_pci_range_to_resource() change microblaze: Fix missing NR_CPUS in menuconfig
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Ingo Molnar: "Fixes from all around the place: - hyper-V 32-bit PAE guest kernel fix - two IRQ allocation fixes on certain x86 boards - intel-mid boot crash fix - intel-quark quirk - /proc/interrupts duplicate irq chip name fix - cma boot crash fix - syscall audit fix - boot crash fix with certain TSC configurations (seen on Qemu) - smpboot.c build warning fix" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86, pageattr: Prevent overflow in slow_virt_to_phys() for X86_PAE ACPI, irq, x86: Return IRQ instead of GSI in mp_register_gsi() x86, intel-mid: Create IRQs for APB timers and RTC timers x86: Don't enable F00F workaround on Intel Quark processors x86/irq: Fix XT-PIC-XT-PIC in /proc/interrupts x86, cma: Reserve DMA contiguous area after initmem_init() i386/audit: stop scribbling on the stack frame x86, apic: Handle a bad TSC more gracefully x86: ACPI: Do not translate GSI number if IOAPIC is disabled x86/smpboot: Move data structure to its primary usage scope
-
Rafael J. Wysocki authored
* pm-cpufreq: cpufreq: cpufreq-dt: Restore default cpumask_setall(policy->cpus) cpufreq: cpufreq-dt: disable unsupported OPPs * pm-sleep: PM / Sleep: fix recovery during resuming from hibernation PM / Sleep: fix async suspend_late/freeze_late error handling
-
Rafael J. Wysocki authored
* acpi-scan: ACPI: Use ACPI companion to match only the first physical device * acpi-ec: ACPI / EC: Fix regression due to conflicting firmware behavior between Samsung and Acer. Revert "ACPI / EC: Add support to disallow QR_EC to be issued before completing previous QR_EC"
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull scheduler fixes from Ingo Molnar: "Various scheduler fixes all over the place: three SCHED_DL fixes, three sched/numa fixes, two generic race fixes and a comment fix" * 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: sched/dl: Fix preemption checks sched: Update comments for CLONE_NEWNS sched: stop the unbound recursion in preempt_schedule_context() sched/fair: Fix division by zero sysctl_numa_balancing_scan_size sched/fair: Care divide error in update_task_scan_period() sched/numa: Fix unsafe get_task_struct() in task_numa_assign() sched/deadline: Fix races between rt_mutex_setprio() and dl_task_timer() sched/deadline: Don't replenish from a !SCHED_DEADLINE entity sched: Fix race between task_group and sched_task_group
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull perf fixes from Ingo Molnar: "Mostly tooling fixes, plus on the kernel side: - a revert for a newly introduced PMU driver which isn't complete yet and where we ran out of time with fixes (to be tried again in v3.19) - this makes up for a large chunk of the diffstat. - compilation warning fixes - a printk message fix - event_idx usage fixes/cleanups" * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: perf probe: Trivial typo fix for --demangle perf tools: Fix report -F dso_from for data without branch info perf tools: Fix report -F dso_to for data without branch info perf tools: Fix report -F symbol_from for data without branch info perf tools: Fix report -F symbol_to for data without branch info perf tools: Fix report -F mispredict for data without branch info perf tools: Fix report -F in_tx for data without branch info perf tools: Fix report -F abort for data without branch info perf tools: Make CPUINFO_PROC an array to support different kernel versions perf callchain: Use global caching provided by libunwind perf/x86/intel: Revert incomplete and undocumented Broadwell client support perf/x86: Fix compile warnings for intel_uncore perf: Fix typos in sample code in the perf_event.h header perf: Fix and clean up initialization of pmu::event_idx perf: Fix bogus kernel printk perf diff: Add missing hists__init() call at tool start
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull futex fixes from Ingo Molnar: "This contains two futex fixes: one fixes a race condition, the other clarifies shared/private futex comments" * 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: futex: Fix a race condition between REQUEUE_PI and task death futex: Mention key referencing differences between shared and private futexes
-
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirelessDavid S. Miller authored
John W. Linville says: ==================== pull request: wireless 2014-10-31 Please pull this small batch of spooky fixes intended for the 3.18 stream...boo! Cyril Brulebois adds an rt2x00 device ID. Dan Carpenter provides a one-line masking fix for an ath9k debugfs entry. Larry Finger gives us a package of small rtlwifi fixes which add some bits that were left out of some feature updates that were included in the merge window. Hopefully this isn't a sign that the rtlwifi base is getting too big... Marc Yang brings a fix for a temporary mwifiex stall when doing 11n RX reordering. Please let me know if there are problems! ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lennart Sorensen authored
The cpsw driver did not support the IFF_ALLMULTI flag which makes dynamic multicast routing not work. Related to this, when enabling IFF_PROMISC in switch mode, all registered multicast addresses are flushed, resulting in only broadcast and unicast traffic being received. A new cpsw_ale_set_allmulti function now scans through the ALE entry table and adds/removes the host port from the unregistered multicast port mask of each vlan entry depending on the state of IFF_ALLMULTI. In promiscious mode, cpsw_ale_set_allmulti is used to force reception of all multicast traffic in addition to the unicast and broadcast traffic. With this change dynamic multicast and promiscious mode both work in switch mode. Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lennart Sorensen authored
0d961b3b (drivers: net: cpsw: fix buggy loop condition) accidentally fixed a loop comparison in too many places while fixing a real bug. It was correct to fix the dual_emac mode section since there 'i' is used as an index into priv->slaves which is a 0 based array. However the other two changes (which are only used in switch mode) are wrong since there 'i' is actually the ALE port number, and port 0 is the host port, while port 1 and up are the slave ports. Putting the loop condition back in the switch mode section fixes it. A comment has been added to point out the intent clearly to avoid future confusion. Also a comment is fixed that said the opposite of what was actually happening. Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca> Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lennart Sorensen authored
The cpsw driver did not support the IFF_ALLMULTI flag which makes dynamic multicast routing not work. Related to this, when enabling IFF_PROMISC in switch mode, all registered multicast addresses are flushed, resulting in only broadcast and unicast traffic being received. A new cpsw_ale_set_allmulti function now scans through the ALE entry table and adds/removes the host port from the unregistered multicast port mask of each vlan entry depending on the state of IFF_ALLMULTI. In promiscious mode, cpsw_ale_set_allmulti is used to force reception of all multicast traffic in addition to the unicast and broadcast traffic. With this change dynamic multicast and promiscious mode both work in switch mode. Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lennart Sorensen authored
0d961b3b (drivers: net: cpsw: fix buggy loop condition) accidentally fixed a loop comparison in too many places while fixing a real bug. It was correct to fix the dual_emac mode section since there 'i' is used as an index into priv->slaves which is a 0 based array. However the other two changes (which are only used in switch mode) are wrong since there 'i' is actually the ALE port number, and port 0 is the host port, while port 1 and up are the slave ports. Putting the loop condition back in the switch mode section fixes it. A comment has been added to point out the intent clearly to avoid future confusion. Also a comment is fixed that said the opposite of what was actually happening. Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca> Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Guenter Roeck authored
If a driver supports reading EEPROM but no EEPROM is installed in the system, the driver's get_eeprom_len function returns 0. ethtool will subsequently try to read that zero-length EEPROM anyway. If the driver does not support EEPROM access at all, this operation will return -EOPNOTSUPP. If the driver does support EEPROM access but no EEPROM is installed, the operation will return -EINVAL. Return -EOPNOTSUPP in both cases for consistency. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ezequiel Garcia authored
Use phy_print_status() to report a change in the PHY status. The current message is not verbose enough, so this commit improves it by using the generic status message. After this change, the kernel reports PHY status down and up events as: mvneta f1070000.ethernet eth0: Link is Down mvneta f1070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Andy Shevchenko authored
The commit 3b57de95 brought the support for a different amount of the filter bins, but didn't update the PCI driver accordingly. This patch appends the default values when the device is enumerated via PCI bus. Fixes: 3b57de95 (net: stmmac: Support devicetree configs for mcast and ucast filter entries) Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
Because bonding stats are usually sum of slave stats, it was not easy to account for tx drops at bonding layer. We can use dev->tx_dropped for this, as this counter is later added to the device stats (in dev_get_stats()) This extends the idea we had in commit ee637714 ("bonding: Simplify the xmit function for modes that use xmit_hash") for bond_3ad_xor_xmit() to other bonding modes. Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Mahesh Bandewar <maheshb@google.com> Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com> Acked-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Tony Lindgren authored
With legacy booting, the platform init code was taking care of the configuring of GPIOs. With device tree based booting, things may or may not work depending what bootloader has configured or if the legacy platform code gets called. Let's add support for the pwrdn and reset GPIOs to the smc91x driver to fix the issues of smc91x not working properly when booted in device tree mode. And let's change n900 to use these settings as some versions of the bootloader do not configure things properly causing errors. Reported-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Dwight Engen authored
The VD_OP_GET_VTOC operation will succeed only if the vdisk backend has a VTOC label, otherwise it will fail. In particular, it will return error 48 (ENOTSUP) if the disk has an EFI label. VTOC disk labels are already handled by directly reading the disk in block/partitions/sun.c (enabled by CONFIG_SUN_PARTITION which defaults to y on SPARC). Since port->label is unused in the driver, remove the call and the field. Signed-off-by: Dwight Engen <dwight.engen@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Pravin B Shelar authored
Kconfig already allows mpls to be built as module. Following patch fixes Makefile to do same. CC: Simon Horman <simon.horman@netronome.com> Signed-off-by: Pravin B Shelar <pshelar@nicira.com> Acked-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Pravin B Shelar authored
mpls gso handler needs to pull skb after segmenting skb. CC: Simon Horman <simon.horman@netronome.com> Signed-off-by: Pravin B Shelar <pshelar@nicira.com> Acked-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull core fixes from Ingo Molnar: "The tree contains two RCU fixes and a compiler quirk comment fix" * 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: rcu: Make rcu_barrier() understand about missing rcuo kthreads compiler/gcc4+: Remove inaccurate comment about 'asm goto' miscompiles rcu: More on deadlock between CPU hotplug and expedited grace periods
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull timer fixes from Thomas Gleixner: "As you requested in the rc2 release mail the timer department serves you a few real bug fixes: - Fix the probe logic of the architected arm/arm64 timer - Plug a stack info leak in posix-timers - Prevent a shift out of bounds issue in the clockevents core" * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: ARM/ARM64: arch-timer: fix arch_timer_probed logic clockevents: Prevent shift out of bounds posix-timers: Fix stack info leak in timer_create()
-
Linus Torvalds authored
Merge tag 'trace-fixes-v3.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace Pull tracing fix from Steven Rostedt: "ARM has system calls outside the NR_syscalls range, and the generic tracing system does not support that and without checks, it can cause an oops to be reported. Rabin Vincent added checks in the return code on syscall events to make sure that the system call number is within the range that tracing knows about, and if not, simply ignores the system call. The system call tracing infrastructure needs to be rewritten to handle these cases better, but for now, to keep from oopsing, this patch will do" * tag 'trace-fixes-v3.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: tracing/syscalls: Ignore numbers outside NR_syscalls' range
-
git://git.lwn.net/linux-2.6Linus Torvalds authored
Pull documentation fixes from Jonathan Corbet: "So this is my first pull request since I rashly agreed to look after the documentation subtree. It contains some typo fixes, a few minor documentation improvements, and, most importantly, fixes for a couple of build problems in various bits of sample code. I fully intend to start sending pull requests with signed tags. However, due to poor planning on my part and the general obnoxiousness of life, I'm 2000 miles away from my private key which is sitting on a powered-down machine. This should be fixed before my next request. Meanwhile git.lwn.net is a machine under my control, the patches are all trivial, and all have done time in linux-next" * tag 'docs-for-linus' of git://git.lwn.net/linux-2.6: Documentation/SubmittingPatches: Reported-by tags and permission Documentation: remove outdated references to the linux-next wiki Documentation: Restrict TSC test code to x86 doc: kernel-parameters.txt: Add ide-generic.probe-mask vdso: don't require 64-bit math in standalone test Documentation: Add CONFIG_DEBUG_KMEMLEAK_DEFAULT_OFF case Documentation: Add default kmemleak off case in kernel-parameters.txt Docs: Document that the sticky bit is understood by hugetlbfs DocBook: Reduce noise from make cleandocs Documentation: fix vdso_standalone_test_x86 on 32-bit Documentation: dt-bindings: Explain order in patch series Documentation/ABI/testing/sysfs-ibft: fix a typo
-