- 28 Aug, 2015 31 commits
-
-
Martin K. Petersen authored
commit f3f5da62 upstream. This fixes a data corruption bug when using discard on top of MD linear, raid0 and raid10 personalities. Commit 20d0189b "block: Introduce new bio_split()" permits sharing the bio_vec between the two resulting bios. That is fine for read/write requests where the bio_vec is immutable. For discards, however, we need to be able to attach a payload and update the bio_vec so the page can get mapped to a scatterlist entry. Therefore the bio_vec can not be shared when splitting discards and we must do a full clone. Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Reported-by:
Seunguk Shin <seunguk.shin@samsung.com> Tested-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Bernhard Bender authored
commit 96849170 upstream. This patch fixes a problem in the usbtouchscreen driver for DMC TSC-30 touch screen. Due to a missing delay between the RESET and SET_RATE commands, the touch screen may become unresponsive during system startup or driver loading. According to the DMC documentation, a delay is needed after the RESET command to allow the chip to complete its internal initialization. As this delay is not guaranteed, we had a system where the touch screen occasionally did not send any touch data. There was no other indication of the problem. The patch fixes the problem by adding a 150ms delay between the RESET and SET_RATE commands. Suggested-by:
Jakob Mustafa <jakob.mustafa@bytecmed.com> Signed-off-by:
Bernhard Bender <bernhard.bender@bytecmed.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Chris Metcalf authored
commit 3f81d244 upstream. We were previously using free_bootmem() and just getting lucky that nothing too bad happened. Signed-off-by:
Chris Metcalf <cmetcalf@ezchip.com> Signed-off-by:
-
Alex Williamson authored
commit 46ebb7af upstream. This continues the attempt to fix commit fb170fb4 ("iommu/vt-d: Introduce helper functions to make code symmetric for readability"). The previous attempt in commit 71684406 ("iommu/vt-d: Detach domain *only* from attached iommus") overlooked the fact that dmar_domain.iommu_bmp gets cleared for VM domains when devices are detached: intel_iommu_detach_device domain_remove_one_dev_info domain_detach_iommu The domain is detached from the iommu, but the iommu is still attached to the domain, for whatever reason. Thus when we get to domain_exit(), we can't rely on iommu_bmp for VM domains to find the active iommus, we must check them all. Without that, the corresponding bit in intel_iommu.domain_ids doesn't get cleared and repeated VM domain creation and destruction will run out of domain IDs. Meanwhile we still can't call iommu_detach_domain() on arbitrary non-VM domains or we risk clearing in-use domain IDs, as 71684406 attempted to address. It's tempting to modify iommu_detach_domain() to test the domain iommu_bmp, but the call ordering from domain_remove_one_dev_info() prevents it being able to work as fb170fb4 seems to have intended. Caching of unused VM domains on the iommu object seems to be the root of the problem, but this code is far too fragile for that kind of rework to be proposed for stable, so we simply revert this chunk to its state prior to fb170fb4. Fixes: fb170fb4 ("iommu/vt-d: Introduce helper functions to make code symmetric for readability") Fixes: 71684406 ("iommu/vt-d: Detach domain *only* from attached iommus") Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> Cc: Jiang Liu <jiang.liu@linux.intel.com> Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
Tomas Winkler authored
commit 154322f4 upstream. chrdev_open() increases reference counter on cdev->owner. Instead of assigning the owner to mei subsystem, the owner has to be set to the underlaying HW module (mei_me or mei_txe), so once the device is opened the HW module cannot be unloaded. Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Signed-off-by:
Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Tejun Heo authored
commit 5f6c2d2b upstream. When a blkcg configuration is targeted to a partition rather than a whole device, blkg_conf_prep fails with -EINVAL; unfortunately, it forgets to put the gendisk ref in that case. Fix it. Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Oliver Neukum authored
commit 5fb2c782 upstream. This device automatically switches itself to another mode (0x1405) unless the specific access pattern of Windows is followed in its initial mode. That makes a dirty unmount of the internal storage devices inevitable if they are mounted. So the card reader of such a device should be ignored, lest an unclean removal become inevitable. This replaces an earlier patch that ignored all LUNs of this device. That patch was overly broad. Signed-off-by:
Oliver Neukum <oneukum@suse.com> Reviewed-by:
Lars Melin <larsm17@gmail.com> Signed-off-by:
-
Alan Stern authored
commit 7d8021c9 upstream. This patch fixes a bug introduced by commit 977dcfdc ("USB: OHCI: don't lose track of EDs when a controller dies"). The commit changed ed_state from ED_UNLINK to ED_IDLE too early, before finish_urb() had been called. The user-visible consequence is that the driver occasionally crashes or locks up when an URB is submitted while another URB for the same endpoint is being unlinked. This patch moves the ED state change later, to the right place. The drawback is that now we may unnecessarily execute some instructions multiple times when a controller dies. Since controllers dying is an exceptional occurrence, a little wasted time won't matter. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Heiko Przybyl <lil_tux@web.de> Tested-by:
-
Lu Baolu authored
commit 2d2a3167 upstream. Commit 25cd2882 ("usb/xhci: Change how we indicate a host supports Link PM.") removed the code to set lpm_capable for USB 3.0 super-speed root hub. The intention of that change was to avoid touching usb core internal field, a.k.a. lpm_capable, and let usb core to set it by checking U1 and U2 exit latency values in the descriptor. Usb core checks and sets lpm_capable in hub_port_init(). Unfortunately, root hub is a special usb device as it has no parent. Hub_port_init() will never be called for a root hub device. That means lpm_capable will by no means be set for the root hub. As the result, lpm isn't functional at all in Linux kernel. This patch add the code to check and set lpm_capable when registering a root hub device. It could be back-ported to kernels as old as v3.15, that contains the Commit 25cd2882 ("usb/xhci: Change how we indicate a host supports Link PM."). Reported-by:
Kevin Strasser <kevin.strasser@linux.intel.com> Signed-off-by:
Lu Baolu <baolu.lu@linux.intel.com> Acked-by:
-
Zhuang Jin Can authored
commit aca3a048 upstream. Port link change with port in resume state should not be reported to usbcore, as this is an internal state to be handled by xhci driver. Reporting PLC to usbcore may cause usbcore clearing PLC first and port change event irq won't be generated. Signed-off-by:
Zhuang Jin Can <jin.can.zhuang@intel.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Zhuang Jin Can authored
commit fac4271d upstream. When the link is just waken, it's in Resume state, and driver sets PLS to U0. This refers to Phase 1. Phase 2 refers to when the link has completed the transition from Resume state to U0. With the fix of xhci: report U3 when link is in resume state, it also exposes an issue that usb3 roothub and controller can suspend right after phase 1, and this causes a hard hang in controller. To fix the issue, we need to prevent usb3 bus suspend if any port is resuming in phase 1. [merge separate USB2 and USB3 port resume checking to one -Mathias] Signed-off-by:
-
Zhuang Jin Can authored
commit 243292a2 upstream. xhci_hub_report_usb3_link_state() returns pls as U0 when the link is in resume state, and this causes usb core to think the link is in U0 while actually it's in resume state. When usb core transfers control request on the link, it fails with TRB error as the link is not ready for transfer. To fix the issue, report U3 when the link is in resume state, thus usb core knows the link it's not ready for transfer. Signed-off-by:
-
Brian Campbell authored
commit 326124a0 upstream. When resetting a device the number of active TTs may need to be corrected by xhci_update_tt_active_eps, but the number of old active endpoints supplied to it was always zero, so the number of TTs and the bandwidth reserved for them was not updated, and could rise unnecessarily. This affected systems using Intel's Patherpoint chipset, which rely on software bandwidth checking. For example, a Lenovo X230 would lose the ability to use ports on the docking station after enough suspend/resume cycles because the bandwidth calculated would rise with every cycle when a suitable device is attached. The correct number of active endpoints is calculated in the same way as in xhci_reserve_bandwidth. Signed-off-by:
Brian Campbell <bacam@z273.org.uk> Signed-off-by:
-
AMAN DEEP authored
commit 34968106 upstream. virt_dev->num_cached_rings counts on freed ring and is not updated correctly. In xhci_free_or_cache_endpoint_ring() function, the free ring is added into cache and then num_rings_cache is incremented as below: virt_dev->ring_cache[rings_cached] = virt_dev->eps[ep_index].ring; virt_dev->num_rings_cached++; here, free ring pointer is added to a current index and then index is incremented. So current index always points to empty location in the ring cache. For getting available free ring, current index should be decremented first and then corresponding ring buffer value should be taken from ring cache. But In function xhci_endpoint_init(), the num_rings_cached index is accessed before decrement. virt_dev->eps[ep_index].new_ring = virt_dev->ring_cache[virt_dev->num_rings_cached]; virt_dev->ring_cache[virt_dev->num_rings_cached] = NULL; virt_dev->num_rings_cached--; This is bug in manipulating the index of ring cache. And it should be as below: virt_dev->num_rings_cached--; virt_dev->eps[ep_index].new_ring = virt_dev->ring_cache[virt_dev->num_rings_cached]; virt_dev->ring_cache[virt_dev->num_rings_cached] = NULL; Signed-off-by:
Aman Deep <aman.deep@samsung.com> Signed-off-by:
-
John Youn authored
commit aebda618 upstream. This fixes an issue introduced in commit b23c8439 (usb: dwc3: gadget: fix DEPSTARTCFG for non-EP0 EPs) that made sure we would only use DEPSTARTCFG once per SetConfig. The trick is that we should use one DEPSTARTCFG per SetConfig *OR* SetInterface. SetInterface was completely missed from the original patch. This problem became aparent after commit 76e838c9 (usb: dwc3: gadget: return error if command sent to DEPCMD register fails) added checking of the return status of device endpoint commands. 'Set Endpoint Transfer Resource' command was caught failing occasionally. This is because the Transfer Resource Index was not getting reset during a SET_INTERFACE request. Finally, to fix the issue, was we have to do is make sure that our start_config_issued flag gets reset whenever we receive a SetInterface request. To verify the problem (and its fix), all we have to do is run test 9 from testusb with 'testusb -t 9 -s 2048 -a -c 5000'. Tested-by:
Huang Rui <ray.huang@amd.com> Tested-by:
Subbaraya Sundeep Bhatta <subbaraya.sundeep.bhatta@xilinx.com> Fixes: b23c8439 (usb: dwc3: gadget: fix DEPSTARTCFG for non-EP0 EPs) Signed-off-by:
John Youn <johnyoun@synopsys.com> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Daniel Vetter authored
commit 5677d67a upstream. It's causing piles of issues since we've stopped forcing full detect cycles in the sysfs interfaces with commit c484f02d Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Fri Mar 6 12:36:42 2015 +0000 drm: Lighten sysfs connector 'status' The original justification for this was that the hpd handlers could use the unknown state as a hint to force a full detection. But current i915 code isn't doing that any more, and no one else really uses reset on resume. So instead just keep the old state around. References: http://article.gmane.org/gmane.comp.freedesktop.xorg.drivers.intel/62584 Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=100641 Cc: Rui Matos <tiagomatos@gmail.com> Cc: Julien Wajsberg <felash@gmail.com> Cc: kuddel.mail@gmx.de Cc: Lennart Poettering <mzxreary@0pointer.de> Acked-by:
Rob Clark <robdclark@gmail.com> Tested-by:
Rui Tiago Cação Matos <tiagomatos@gmail.com> Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com> Signed-off-by:
-
David Henningsson authored
commit cba59972 upstream. Without this patch, the headset mic will not work on this machine. BugLink: https://bugs.launchpad.net/bugs/1476987Signed-off-by:
David Henningsson <david.henningsson@canonical.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
NeilBrown authored
commit 299b0685 upstream. 'reshape_position' tracks where in the reshape we have reached. 'reshape_safe' tracks where in the reshape we have safely recorded in the metadata. These are compared to determine when to update the metadata. So it is important that reshape_safe is initialised properly. Currently it isn't. When starting a reshape from the beginning it usually has the correct value by luck. But when reducing the number of devices in a RAID10, it has the wrong value and this leads to the metadata not being updated correctly. This can lead to corruption if the reshape is not allowed to complete. This patch is suitable for any -stable kernel which supports RAID10 reshape, which is 3.5 and later. Fixes: 3ea7daa5 ("md/raid10: add reshape support") Signed-off-by:
NeilBrown <neilb@suse.com> Signed-off-by:
-
Chris Wilson authored
commit 648a9bc5 upstream. Since the hardware sometimes mysteriously totally flummoxes the 64bit read of a 64bit register when read using a single instruction, split the read into two instructions. Since the read here is of automatically incrementing timestamp counters, we also have to be very careful in order to make sure that it does not increment between the two instructions. However, since userspace tried to workaround this issue and so enshrined this ABI for a broken hardware read and in the process neglected that the read only fails in some environments, we have to introduce a new uABI flag for userspace to request the 2x32 bit accurate read of the timestamp. v2: Fix alignment check and include details of the workaround for userspace. Reported-by:
Karol Herbst <freedesktop@karolherbst.de> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91317 Testcase: igt/gem_reg_read Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Michał Winiarski <michal.winiarski@intel.com> Tested-by:
Michał Winiarski <michal.winiarski@intel.com> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> [ kamal: backport to 3.19-stable: context ] Signed-off-by:
-
Aaron Plattner authored
commit 6c3d9119 upstream. Vendor ID 0x10de007d is used by a yet-to-be-named GPU chip. This chip also has the 2-ch audio swapping bug, so patch_nvhdmi is appropriate here. Signed-off-by:
Aaron Plattner <aplattner@nvidia.com> Signed-off-by:
-
Simon Guinot authored
commit a84e3289 upstream. With the actual code, if a memory allocation error happens while refilling a Rx descriptor, then the original Rx buffer is both passed to the networking stack (in a SKB) and let in the Rx ring. This leads to various kernel oops and crashes. As a fix, this patch moves Rx descriptor refilling ahead of building SKB with the associated Rx buffer. In case of a memory allocation failure, data is dropped and the original DMA buffer is put back into the Rx ring. Signed-off-by:
Simon Guinot <simon.guinot@sequanux.org> Fixes: c5aff182 ("net: mvneta: driver for Marvell Armada 370/XP network unit") Tested-by:
Yoann Sculo <yoann@sculo.fr> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Kirill A. Shutemov authored
commit a8965276 upstream. MPX setups private anonymous mapping, but uses vma->vm_ops too. This can confuse core VM, as it relies on vm->vm_ops to distinguish file VMAs from anonymous. As result we will get SIGBUS, because handle_pte_fault() thinks it's file VMA without vm_ops->fault and it doesn't know how to handle the situation properly. Let's fix that by not setting ->vm_ops. We don't really need ->vm_ops here: MPX VMA can be detected with VM_MPX flag. And vma_merge() will not merge MPX VMA with non-MPX VMA, because ->vm_flags won't match. The only thing left is name of VMA. I'm not sure if it's part of ABI, or we can just drop it. The patch keep it by providing arch_vma_name() on x86. Signed-off-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by:
Dave Hansen <dave.hansen@linux.intel.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: dave@sr71.net Link: http://lkml.kernel.org/r/20150720212958.305CC3E9@viggo.jf.intel.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> [ kamal: backport to 3.19-stable: fewer is_mpx_vma() calls to replace ] Signed-off-by:
-
Dave Hansen authored
commit bbc03778 upstream. flush_tlb_info->flush_start/end are both normal virtual addresses. When calculating 'nr_pages' (only used for the tracepoint), I neglected to put parenthesis in. Thanks to David Koufaty for pointing this out. Signed-off-by:
-
Maruthi Srinivas Bayyavarapu authored
commit 5022813d upstream. Fixes audio problems on newer asics Signed-off-by:
Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com> Signed-off-by:
-
Uwe Kleine-König authored
commit 9571b25d upstream. imx1_pinconf_set assumes that the array of pins in struct imx1_pinctrl_soc_info can be indexed by pin id to get the pinctrl_pin_desc for a pin. This used to be correct up to commit 607af165 which removed some entries from the array and so made it wrong to access the array by pin id. The result of this bug is a wrong pin name in the output for small pin ids and an oops for the bigger ones. This patch is the result of a discussion that includes patches by Markus Pargmann and Chris Ruehl. Fixes: 607af165 ("pinctrl: i.MX27: Remove nonexistent pad definitions") Reported-by:
Chris Ruehl <chris.ruehl@gtsys.com.hk> Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by:
Markus Pargmann <mpa@pengutronix.de> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Mateusz Sylwestrzak authored
commit 0420694d upstream. Acer Aspire V5 with the ALC282 codec is given the wrong value for the 0x19 PIN by the laptop's BIOS. Overriding it with the correct value adds support for the headset microphone which would not otherwise be visible in the system. The fix is based on commit 7819717b with a similar quirk for Acer Aspire with the ALC269 codec. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96201Signed-off-by:
Mateusz Sylwestrzak <matisec7@gmail.com> Signed-off-by:
-
Fugang Duan authored
commit bf604a4c upstream. Read the register only when the adc register address is 4 byte aligned. (rather than the other way around). Signed-off-by:
Haibo Chen <haibo.chen@freescale.com> Signed-off-by:
Fugang Duan <B38611@freescale.com> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Takashi Iwai authored
commit 67756e31 upstream. With the nonatomic PCM ops, the system may spew lockdep warnings like: ============================================= [ INFO: possible recursive locking detected ] 4.2.0-rc1-jeejaval3 #12 Not tainted --------------------------------------------- aplay/4029 is trying to acquire lock: (snd_pcm_link_rwsem){.+.+.+}, at: [<ffffffff816fd473>] snd_pcm_stream_lock+0x43/0x60 but task is already holding lock: (snd_pcm_link_rwsem){.+.+.+}, at: [<ffffffff816fcf29>] snd_pcm_action_nonatomic+0x29/0x80 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(snd_pcm_link_rwsem); lock(snd_pcm_link_rwsem); Although this is false-positive as the rwsem is taken always as read-only for these code paths, it's certainly annoying to see this at any occasion. A simple fix is to use down_read_nested() in snd_pcm_stream_lock() that can be called inside another lock. Reported-by:
Vinod Koul <vinod.koul@intel.com> Reported-by:
Jeeja Kp <jeeja.kp@intel.com> Tested-by:
-
Tom Hughes authored
commit 4479004e upstream. If we don't do this, and we then fail to recreate the debugfs directory during a mode change, then we will fail later trying to add stations to this now bogus directory: BUG: unable to handle kernel NULL pointer dereference at 0000006c IP: [<c0a92202>] mutex_lock+0x12/0x30 Call Trace: [<c0678ab4>] start_creating+0x44/0xc0 [<c0679203>] debugfs_create_dir+0x13/0xf0 [<f8a938ae>] ieee80211_sta_debugfs_add+0x6e/0x490 [mac80211] Signed-off-by:
Tom Hughes <tom@compton.nu> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Martin K. Petersen authored
commit 9051bd39 upstream. A new Micron drive was just announced, once again recycling the first part of the model string. Add an underscore to the M510/M550 pattern to avoid picking up the new DC drive. Signed-off-by:
-
Stefan Agner authored
commit 25b401c1 upstream. If a valid power regulator or a dummy regulator is used (which happens to be the case when no regulator is specified), restart_work is queued no matter whether the device was running or not at suspend time. Since work queues get initialized in the ndo_open callback, resuming leads to a NULL pointer exception. Reverse exactly the steps executed at suspend time: - Enable the power regulator in any case - Enable the transceiver regulator if the device was running, even in case we have a power regulator - Queue restart_work only in case the device was running Fixes: bf66f373 ("can: mcp251x: Move to threaded interrupts instead of workqueues.") Signed-off-by:
Stefan Agner <stefan@agner.ch> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
- 27 Aug, 2015 9 commits
-
-
Mikulas Patocka authored
commit d531be2c upstream. I have a ST4000DM000 disk. If Linux is booted while the disk is spun down, the command that sets transfer mode causes the disk to spin up. The spin-up takes longer than the default 5s timeout, so the command fails and timeout is reported. Fix this by increasing the timeout to 15s, which is enough for the disk to spin up. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
-
David Milburn authored
commit af34d637 upstream. Since no longer limiting max_sectors to BLK_DEF_MAX_SECTORS (commit 34b48db6), data corruption may occur on ST380013AS drive configured on 82801JI (ICH10 Family) SATA controller. This patch will allow the driver to limit max_sectors as before # cat /sys/block/sdb/queue/max_sectors_kb 512 I was able to double the max_sectors_kb value up to 16384 on linux-4.2.0-rc2 before seeing corruption, but seems safer to use previous limit. Without this patch max_sectors_kb will be 32767. tj: Minor comment update. Reported-by:
Jeff Moyer <jmoyer@redhat.com> Signed-off-by:
David Milburn <dmilburn@redhat.com> Signed-off-by:
-
Arne Fitzenreiter authored
commit cda57b1b upstream. This device loses blocks, often the partition table area, on trim. Disable TRIM. http://pcengines.ch/msata16a.htmSigned-off-by:
Arne Fitzenreiter <arne_f@ipfire.org> Signed-off-by:
-
Arne Fitzenreiter authored
commit 71d126fd upstream. Some devices lose data on TRIM whether queued or not. This patch adds a horkage to disable TRIM. tj: Collapsed unnecessary if() nesting. Signed-off-by:
-
Thomas Hebb authored
commit 96696a9d upstream. The marvell,berlin2cd-usb-phy compatible incorrectly sets the PLL divider to BG2's value instead of BG2CD/BG2Q's. Change it to the right value. Signed-off-by:
Thomas Hebb <tommyhebb@gmail.com> Signed-off-by:
Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by:
-
Luck, Tony authored
commit 4c62360d upstream. The memory error record structure includes as its first field a bitmask of which subsequent fields are valid. The allows new fields to be added to the structure while keeping compatibility with older software that parses these records. This mechanism was used between versions 2.2 and 2.3 to add four new fields, growing the size of the structure from 73 bytes to 80. But Linux just added all the new fields so this test: if (gdata->error_data_length >= sizeof(*mem_err)) cper_print_mem(newpfx, mem_err); else goto err_section_too_small; now make Linux complain about old format records being too short. Add a definition for the old format of the structure and use that for the minimum size check. Pass the actual size to cper_print_mem() so it can sanity check the validation_bits field to ensure that if a BIOS using the old format sets bits as if it were new, we won't access fields beyond the end of the structure. Signed-off-by:
Tony Luck <tony.luck@intel.com> Signed-off-by:
Matt Fleming <matt.fleming@intel.com> Signed-off-by:
-
Aleksei Mamlin authored
commit 08c85d2a upstream. Enabling AA on HP 250GB SATA disk VB0250EAVER causes errors: [ 3.788362] ata3.00: failed to enable AA (error_mask=0x1) [ 3.789243] ata3.00: failed to enable AA (error_mask=0x1) Add the ATA_HORKAGE_BROKEN_FPDMA_AA for this specific harddisk. tj: Collected FPDMA_AA entries and updated comment. Signed-off-by:
Aleksei Mamlin <mamlinav@gmail.com> Signed-off-by:
-
Lior Amsalem authored
commit 945b4744 upstream. This commit adds the necessary quirk to make the Marvell 4140 SATA PMP work properly. This PMP doesn't like SRST on port number 4 (the host port) so this commit marks this port as not supporting SRST. Signed-off-by:
Lior Amsalem <alior@marvell.com> Reviewed-by:
Nadav Haklai <nadavh@marvell.com> Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by:
-
Antonio Borneo authored
commit 6debce6f upstream. Current implementation of cp2112_raw_event() only accepts one data report at a time. If last received data report is not fully handled yet, a new incoming data report will overwrite it. In such case we don't guaranteed to propagate the correct incoming data. The trivial fix implemented here forces a single report at a time by requesting in cp2112_read() no more than 61 byte of data, which is the payload size of a single data report. Signed-off-by:
Antonio Borneo <borneo.antonio@gmail.com> Tested-by:
Ellen Wang <ellen@cumulusnetworks.com> Signed-off-by:
Jiri Kosina <jkosina@suse.com> Signed-off-by:
-
