Implement this callback so that the driver reports correctly
the direction setting of each line.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The gpiochip calls are already checking that the GPIO line
offsets are in range.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Make the text clearer, remove reference to confusing "positive"
and "negative" and elaborate a bit.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Now GPIO IRQ loss is observed on dra7-evm after suspend/resume cycle
in the following case:
  extcon_usb1(id_irq) ->  pcf8575.gpio1 -> omapgpio6.gpio11 -> gic

the extcon_usb1 is wake up source and it enables IRQ wake up for
id_irq by calling enable/disable_irq_wake() during suspend/resume
which, in turn, causes execution of omap_gpio_wake_enable(). And
omap_gpio_wake_enable() will set/clear corresponding bit in
GPIO_IRQWAKEN_x register.

omapgpio6 configuration after boot - wakeup is enabled for GPIO IRQs
by default from  omap_gpio_irq_type:
GPIO_IRQSTATUS_SET_0    | 0x00000400
GPIO_IRQSTATUS_CLR_0    | 0x00000400
GPIO_IRQWAKEN_0         | 0x00000400
GPIO_RISINGDETECT       | 0x00000000
GPIO_FALLINGDETECT      | 0x00000400

omapgpio6 configuration after after suspend/resume cycle:
GPIO_IRQSTATUS_SET_0    | 0x00000400
GPIO_IRQSTATUS_CLR_0    | 0x00000400
GPIO_IRQWAKEN_0         | 0x00000000 <---
GPIO_RISINGDETECT       | 0x00000000
GPIO_FALLINGDETECT      | 0x00000400

As result, system will start to lose interrupts from pcf8575 GPIO
expander, because when OMAP GPIO IP is in smart-idle wakeup mode, there
is no guarantee that transition(s) on input non wake up GPIO pin will
trigger asynchronous wake-up request to PRCM and then IRQ generation.
IRQ will be generated when GPIO is in active mode - for example, some
time after accessing GPIO bank registers IRQs will be generated
normally, but issue will happen again once PRCM will put GPIO in low
power smart-idle wakeup mode.

Note 1. Issue is not reproduced if debounce clk is enabled for GPIO
bank.

Note 2. Issue hardly reproducible if GPIO pins group contains both
wakeup/non-wakeup gpios - for example, it will be hard to reproduce
issue with pin2 if GPIO_IRQWAKEN_0=0x1 GPIO_IRQSTATUS_SET_0=0x3
GPIO_FALLINGDETECT = 0x3 (TRM "Power Saving by Grouping the Edge/Level
Detection").

Note 3. There nothing common bitween System wake up and OMAP GPIO bank
IP wake up logic - the last one defines how the GPIO bank ON-IDLE-ON
transition will happen inside SoC under control of PRCM.

Hence, fix the problem by removing omap_set_gpio_wakeup() function
completely and so keeping always in sync GPIO IRQ mask/unmask
(IRQSTATUS_SET) and wake up enable (GPIO_IRQWAKEN) bits; and adding
IRQCHIP_MASK_ON_SUSPEND flag in OMAP GPIO irqchip. That way non wakeup
GPIO IRQs will be properly masked/unmask by IRQ PM core during
suspend/resume cycle.

Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Bard Liao <bardliao@realtek.com>
Cc: Oder Chiou <oder_chiou@realtek.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Jiri Slaby <jslaby@suse.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Jiri Slaby <jslaby@suse.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Manohar Vanga <manohar.vanga@gmail.com>
Cc: devel@driverdev.osuosl.org
Acked-by: Martyn Welch <martyn@welchs.me.uk>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Michael Buesch <m@bues.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Feng Tang <feng.tang@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Instead of indirectly selecting GPIOLIB via the
ARCH_REQUIRE_GPIOLIB symbol, just select GPIOLIB.

Cc: Michael Büsch <m@bues.ch>
Cc: linux-snps-arc@lists.infradead.org
Acked-by: Vineet Gupta <vgupt@synopsys.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This symbols is not needed to get access to selecting the
GPIOLIB anymore: any arch can select GPIOLIB.

Cc: Michael Büsch <m@bues.ch>
Cc: sparclinux@vger.kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Replace "select ARCH_REQUIRE_GPIOLIB" with "select GPIOLIB"
as this can now be selected directly.

Cc: Michael Büsch <m@bues.ch>
Cc: Mikael Starvik <starvik@axis.com>
Cc: linux-cris-kernel@axis.com
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This symbols is not needed to get access to selecting the
GPIOLIB anymore: any arch can select GPIOLIB.

Cc: Michael Büsch <m@bues.ch>
Cc: nios2-dev@lists.rocketboards.org
Acked-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Replace "select ARCH_REQUIRE_GPIOLIB" with "select GPIOLIB"
as this can now be selected directly.

Cc: Michael Büsch <m@bues.ch>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This symbols is not needed to get access to selecting the
GPIOLIB anymore: any arch can select GPIOLIB.

Cc: Michael Büsch <m@bues.ch>
Cc: Chris Zankel <chris@zankel.net>
Cc: linux-xtensa@linux-xtensa.org
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This symbols is not needed to get access to selecting the
GPIOLIB anymore: any arch can select GPIOLIB.

Cc: Michael Büsch <m@bues.ch>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: linux-alpha@vger.kernel.org
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This symbols is not needed to get access to selecting the
GPIOLIB anymore: any arch can select GPIOLIB.

Cc: Michael Büsch <m@bues.ch>
Cc: linux-metag@vger.kernel.org
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Replace "select ARCH_REQUIRE_GPIOLIB" with "select GPIOLIB"
as this can now be selected directly.

Cc: Michael Büsch <m@bues.ch>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Acked-by: Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The GPIOLIB symbol currently require that
ARCH_WANT_OPTIONAL_GPIOLIB or ARCH_REQUIRE_GPIOLIB is selected
to be selectable.

The ARCH_REQUIRE_GPIOLIB does only one thing: select GPIOLIB.

This is just confusing: architectures that want GPIOLIB should
be able to configure it in no matter what, and those who
require it should just select GPIOLIB.

It also creates problems for drivers that need to state
"select GPIOLIB" to get dependencies: those depend on the
selected architecture to select
ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB first, and will cause
compile errors for the few archs that state neither.

These intermediary symbols need to go.

As a first step, remove the dependencies so that:

- ARCH_WANT_OPTIONAL_GPIOLIB becomes a noop (GPIOLIB will be
  available for everyone) and

- "select ARCH_REQUIRE_GPIOLIB" can be replaced by just
  "select GPIOLIB"

After this patch we can follow up with patches cleaning up the
architectures one-by one and eventually remove the
ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB symbols altogether.
Reported-by: Michael Hennerich <michael.hennerich@analog.com>
Cc: Michael Büsch <m@bues.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Keep the words talking about what a GPIO bank is, but remove the
binding. We have not agreed that this is something we want to have.
Acked-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This renames gpiod_set_array_value_priv() to
gpiod_set_array_value_complex() and moves it to the gpiolib.h
private header file so we can reuse it in the subsystem.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fix a typo causing a build regression.

Fixes: f90c6bdb ("gpio: f7188x: use the new open drain callback")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

I did only find them after a fuzzy search, so let them be where one
would expect them.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Return proper error in brcmstb_gpio_probe if bank width is invalid.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Print the error number of GPIO hog failed during its configurations.
This helps in identifying the failure without instrumenting the code.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Look for child node which are available when iterating for
gpio hog node for request/set GPIO initial configuration
during OF gpio chip registration.

All it really does is make it possible to set
status = "disabled"; in the hog nodes, and then they will
not be applied.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Allow compile testing this driver by adding a new config option which
is enabled by default and depends on the old symbol or COMPILE_TEST.
Signed-off-by: Alexander Stein <alexanders83@web.de>

Lower dependencies for compile testing.
Signed-off-by: Alexander Stein <alexanders83@web.de>

The WM8994 GPIOs clearly have a dedicated open drain control
register. Implement support for controlling this from GPIO
descriptor tables or other hardware descriptions such as
device tree by implementing the .set_single_ended() callback.

Before this patch, lines requesting open drain will just be
switched to input mode by the framework, thus emulating open
drain. But the hardware can do the real thing, so let's
support that.

As part of this, rename the debugfs string for output mode
from "CMOS" to "push-pull" because it is the term used in
the framework to signify a tomem-pole CMOS output.

Cc: patches@opensource.wolfsonmicro.com
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The WM831x GPIOs clearly have a dedicated open drain control
register. Implement support for controlling this from GPIO
descriptor tables or other hardware descriptions such as
device tree by implementing the .set_single_ended() callback.

Before this patch, lines requesting open drain will just be
switched to input mode by the framework, thus emulating open
drain. But the hardware can do the real thing, so let's
support that.

As part of this, rename the debugfs string for output mode
from "CMOS" to "push-pull" because it is the term used in
the framework to signify a tomem-pole CMOS output.

Cc: patches@opensource.wolfsonmicro.com
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The vx855 driver clearly states it has three groups of lines:
GPI, GPO and GPIO. The GPO are assumedly push-pull. The GPIO
are implicit open drain, but if the GPIO subsystem ask for them
to be explicitly open drain (i.e. set the flag on a machine table
that we want open drain) it will currently misbehave: it will
switch the GPIOs to input mode (emulate open drain). Instead:
indicate in the .set_single_ended() callback that we support
open drain and open drain only.

Cc: Daniel Drake <drake@endlessm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The menz127 driver tries to support open drain by detecting it
at request time. However: without the new callbacks from the
gpiolib it is not really working: the core will still just emulate
the open drain mode by switching the line to an input.

By adding a hook into the new .set_single_ended() call rather than
trying to autodetect at request() time, proper open drain can be
supported.

Cc: Andreas Werner <andy@wernerandy.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The F7188x chips supports setting the pins in open drain mode.
Activate the new .set_single_ended() callback.

Cc: Peter Hung <hpeter@gmail.com>
Cc: Andreas Bofjall <andreas@gazonk.org>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>