Add CAN device node and pinctrl on i.MX8MP evk board.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

There are two spdif IP on imx8mq, spdif1 is for normal
spdif device, spdif2 is for HDMI ARC interface.

Enable these spdif sound card in this patch.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Configure clock rate for audio plls. audio pll1 is used
as parent clock for clocks that is multiple of 8kHz.
audio pll2 is used as parent clock for clocks that is
multiple of 11kHz.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add PCIe EP node for ls1088a to support EP mode.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Annotate the EMDIO1 node and describe the 2 AQR107 PHYs found on the
LX2160ARDB board. Also, add the necessary phy-handles for DPMACs 3 and 4
to their associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add PCS MDIO nodes for the internal MDIO buses on the LX2160A, along
with their internal PCS PHYs, which will be used when the DPMAC is
in TYPE_PHY mode.
Also, rename the dpmac@x nodes to ethernet@x in order to be compliant
with the naming convention used by ethernet controllers.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add PCS MDIO nodes for the internal MDIO buses on the LS208x SoCs, along
with their internal PCS PHYs which will be used when the DPMAC object is
in TYPE_PHY mode.
Also, rename the dpmac@x nodes to ethernet@x in order to be compliant
with the naming convention used by ethernet controllers.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Annotate the EMDIO2 node and describe the other 4 10GBASER PHYs found on
the LS2088ARDB board. Also, add phy-handles for DPMACs 5-8 to their
associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Annotate the EMDIO1 node and describe the 4 10GBASER PHYs found on the
LS2088ARDB board. Also, add phy-handles for DPMACs 1-4 to their
associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the external MDIO device nodes found in the WRIOP global memory
region. This is needed for management of external PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Annotate the external MDIO2 node and describe the 10GBASER PHY found on
the LS1088ARDB board and add a phy-handle for DPMAC2 to link it.
Also, add the internal PCS MDIO node for the internal MDIO buses found
on the LS1088A SoC along with its internal PCS PHY and link the
corresponding DPMAC to the PCS through the pcs-handle.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Annotate the external MDIO1 node and describe the 8 QSGMII PHYs found on
the LS1088ARDB board and add phy-handles for DPMACs 3-10 to its
associated PHY.  Also, add the internal PCS MDIO nodes for the internal
MDIO buses found on the LS1088A SoC along with their internal PCS PHY
and link the corresponding DPMAC to the PCS through the pcs-handle.
Also, rename the dpmac@x nodes to ethernet@x in order to be compliant
with the naming convention used by ethernet controllers.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the external MDIO device nodes found in the WRIOP global memory
region. This is needed for management of external PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add device tree support for LX2162AQDS board.
LX2162A has same die as of LX2160A with different packaging.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The pinmux subnodes are indented too much.  This patch does nothing
more than remove an extra tab.  There are no functional changes.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

In accordance with the DWC USB3 bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "snps,dwc3"-compatible nodes are correctly
named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The i.MX8M Mini can support SPDIF which is compatible to the
IP used on the i.MX35.  Add the node.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The i.MX8M Mini has supports the MICFIL digital interface.
It's a 16-bit audio signal from a PDM microphone bitstream.
The driver is already in the kernel, but the node is missing.

This patch adds the micfil node.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Different revision of i.MX8MP EVK boards may have different external
pull up registor design, some are enabled while some are NOT, to make
sure the WDOG_B pin works properly, better to enable internal pull up
resistor. Since enabling internal pull up resistor is NOT harmful and
having benefit of flexibility on different board design, just enable
it for all i.MX8MP boards; And schmitt input is NOT necessary for this
WDOG_B output pin, so remove it; Open drain outputs provide more
flexibility to a designer as they can be pulled-up to any voltage found
in the system, so enable it as well.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Different revision of i.MX8MN EVK boards may have different external
pull up registor design, some are enabled while some are NOT, to make
sure the WDOG_B pin works properly, better to enable internal pull up
resistor. Since enabling internal pull up resistor is NOT harmful and
having benefit of flexibility on different board design, just enable
it for all i.MX8MN boards; And schmitt input is NOT necessary for this
WDOG_B output pin, so remove it; Open drain outputs provide more
flexibility to a designer as they can be pulled-up to any voltage found
in the system, so enable it as well.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Different revision of i.MX8MM EVK boards may have different external
pull up registor design, some are enabled while some are NOT, to make
sure the WDOG_B pin works properly, better to enable internal pull up
resistor. Since enabling internal pull up resistor is NOT harmful and
having benefit of flexibility on different board design, just enable
it for all i.MX8MM boards; And schmitt input is NOT necessary for this
WDOG_B output pin, so remove it; Open drain outputs provide more
flexibility to a designer as they can be pulled-up to any voltage found
in the system, so enable it as well.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx8mm-beacon-som has a Quad-SPI NOR flash connected to the FlexSPI bus.

This patch enables the FlexSPI bus and configures it to work with the
flash part.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Each cpu core should have a corresponding supply, but only cpu0 does.
This patch adds a supply for each of the secondary cpus.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Kontron Electronics GmbH offers small and powerful SoMs based on the
i.MX8M Mini SoC including PMIC, LPDDR4-RAM, eMMC and SPI NOR.

The matching baseboards have the same form factor and similar interfaces
as the other boards from the Kontron "Board-Line" family, including
SD card, 1G Ethernet, 100M Ethernet, USB Host/OTG, digital IOs, RS232,
RS485, CAN, LVDS or HDMI, RTC and much more.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add PMU node to enable pmu support on imx8mn.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add PMU node to enable pmu support on imx8mp.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX 8M Plus has four Cortex-A CPUs, not six.  Using higher value is
harmless but adjust it to match real HW.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX 8M Nano has four Cortex-A CPUs, not six.  Using higher value is
harmless but adjust it to match real HW.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

i.MX 8M Mini has four Cortex-A CPUs, not six.  Using higher value is
harmless but adjust it to match real HW.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The dtschema expects watchdog device node name to be "watchdog":

  arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dt.yaml: wdog@2ad0000:
    $nodename:0: 'wdog@2ad0000' does not match '^watchdog(@.*|-[0-9a-f])?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

PMIC driver is ready on i.MX8MN EVK board, assign cpu-supply for
each A53 and restore the operating points table to enable cpufreq.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The module supports one CAN controller. Enable it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The LS1028A has two FlexCAN controller. These are compatible with
the ones from the LX2160A. Add the nodes.

The first controller was tested on the Kontron sl28 board.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

dtschema expects GPIO hogs to end with 'hog' suffix.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.

Remove the quote operator # from compiler_attributes.h __section macro.

Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.

Conversion done using the script at:

    https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.plSigned-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

tid_addr is not a "pointer to (pointer to int in userspace)"; it is in
fact a "pointer to (pointer to int in userspace) in userspace".  So
sparse rightfully complains about passing a kernel pointer to
put_user().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 453431a5 ("mm, treewide: rename kzfree() to
kfree_sensitive()") renamed kzfree() to kfree_sensitive(),
but it left a compatibility definition of kzfree() to avoid
being too disruptive.

Since then a few more instances of kzfree() have slipped in.

Just get rid of them and remove the compatibility definition
once and for all.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If set, use the environment variable GIT_DIR to change the default .git
location of the kernel git tree.

If GIT_DIR is unset, keep using the current ".git" default.

Link: https://lkml.kernel.org/r/c5e23b45562373d632fccb8bc04e563abba4dd1d.camel@perches.comSigned-off-by: Joe Perches <joe@perches.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull timer fixes from Thomas Gleixner:
 "A time namespace fix and a matching selftest. The futex absolute
  timeouts which are based on CLOCK_MONOTONIC require time namespace
  corrected. This was missed in the original time namesapce support"

* tag 'timers-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  selftests/timens: Add a test for futex()
  futex: Adjust absolute futex timeouts with per time namespace offset