It incorrectly identifies itself as "IPv4" packet logging.
Signed-off-by: Steven Noonan <steven@uplinklabs.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

This resolves linking problems with CONFIG_IPV6=n:

net/built-in.o: In function `redirect_tg6':
xt_REDIRECT.c:(.text+0x6d021): undefined reference to `nf_nat_redirect_ipv6'
Reported-by: Andreas Ruprecht <rupran@einserver.de>
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

This patch adds the missing bits to allow to match per meta l4proto from
the bridge. Example:

  nft add rule bridge filter input ether type {ip, ip6} meta l4proto udp counter
Signed-off-by: Alvaro Neira Ayuso <alvaroneay@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

This patch exports the functions nft_reject_iphdr_validate and
nft_reject_ip6hdr_validate to use it in follow up patches.
These functions check if the IPv4/IPv6 header is correct.
Signed-off-by: Alvaro Neira Ayuso <alvaroneay@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

add a __nfct_init_offset annotation member to struct nf_conn to make
it clear which members are covered by the memset when the conntrack
is allocated.

This avoids zeroing timer_list and ct_net; both are already inited
explicitly.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

The maximum value for the hitcount parameter is given by
"ip_pkt_list_tot" parameter (default: 20).

Exceeding this value on the command line will cause the rule to be
rejected.  The parameter is also readonly, i.e. it cannot be changed
without module unload or reboot.

Store size per table, then base nstamps[] size on the hitcount instead.

The module parameter is retained for backwards compatibility.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Add minimal runtime PM support (enable on probe, disable on remove), to
ensure proper operation with a parent device that uses runtime PM.

This is needed on systems where the external bus controller module of
the SoC is contained in a PM domain and/or has a gateable functional
clock. In such cases, before accessing any device connected to the
external bus, the PM domain must be powered up, and/or the functional
clock must be enabled, which is typically handled through runtime PM by
the bus controller driver.

An example of this is the kzm9g development board, where an smsc9220
Ethernet controller is connected to the Bus State Controller (BSC) of a
Renesas sh73a0 SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc_netlink.h is the user-space header for the new netlink api. It
was accidentally left out of the uapi Kbuild list when the api was
added.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Verify whether both the lock and RCU protected iterators see all
test entries before and after expanding and shrinking has been
performed. Also verify whether the number of entries in the hashtable
remains stable during expansion and shrinking.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Should be u16. So fix it to kill the sparse warning.

Fixes: c7e2b968 "sched: introduce vlan action"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix sparse warnings about non-static declaration of static functions
in the new tipc netlink API.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
netfilter/ipvs updates for net-next

The following patchset contains Netfilter updates for your net-next
tree, this includes the NAT redirection support for nf_tables, the
cgroup support for nft meta and conntrack zone support for the connlimit
match. Coming after those, a bunch of sparse warning fixes, missing
netns bits and cleanups. More specifically, they are:

1) Prepare IPv4 and IPv6 NAT redirect code to use it from nf_tables,
   patches from Arturo Borrero.

2) Introduce the nf_tables redir expression, from Arturo Borrero.

3) Remove an unnecessary assignment in ip_vs_xmit/__ip_vs_get_out_rt().
   Patch from Alex Gartrell.

4) Add nft_log_dereference() macro to the nf_log infrastructure, patch
   from Marcelo Leitner.

5) Add some extra validation when registering logger families, also
   from Marcelo.

6) Some spelling cleanups from stephen hemminger.

7) Fix sparse warning in nf_logger_find_get().

8) Add cgroup support to nf_tables meta, patch from Ana Rey.

9) A Kconfig fix for the new redir expression and fix sparse warnings in
   the new redir expression.

10) Fix several sparse warnings in the netfilter tree, from
    Florian Westphal.

11) Reduce verbosity when OOM in nfnetlink_log. User can basically do
    nothing when this situation occurs.

12) Add conntrack zone support to xt_connlimit, again from Florian.

13) Add netnamespace support to the h323 conntrack helper, contributed
    by Vasily Averin.

14) Remove unnecessary nul-pointer checks before free_percpu() and
    module_put(), from Markus Elfring.

15) Use pr_fmt in nfnetlink_log, again patch from Marcelo Leitner.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver is very similar to the macvlan driver except that it
uses L3 on the frame to determine the logical interface while
functioning as packet dispatcher. It inherits L2 of the master
device hence the packets on wire will have the same L2 for all
the packets originating from all virtual devices off of the same
master device.

This driver was developed keeping the namespace use-case in
mind. Hence most of the examples given here take that as the
base setup where main-device belongs to the default-ns and
virtual devices are assigned to the additional namespaces.

The device operates in two different modes and the difference
in these two modes in primarily in the TX side.

(a) L2 mode : In this mode, the device behaves as a L2 device.
TX processing upto L2 happens on the stack of the virtual device
associated with (namespace). Packets are switched after that
into the main device (default-ns) and queued for xmit.

RX processing is simple and all multicast, broadcast (if
applicable), and unicast belonging to the address(es) are
delivered to the virtual devices.

(b) L3 mode : In this mode, the device behaves like a L3 device.
TX processing upto L3 happens on the stack of the virtual device
associated with (namespace). Packets are switched to the
main-device (default-ns) for the L2 processing. Hence the routing
table of the default-ns will be used in this mode.

RX processins is somewhat similar to the L2 mode except that in
this mode only Unicast packets are delivered to the virtual device
while main-dev will handle all other packets.

The devices can be added using the "ip" command from the iproute2
package -

	ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ]
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Laurent Chavey <chavey@google.com>
Cc: Tim Hockin <thockin@google.com>
Cc: Brandon Philips <brandon.philips@coreos.com>
Cc: Pavel Emelianov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As pointed out by Ben Hutchings drivers that allow using VLAN have to
provide enough headroom for the VLAN tags.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

i.MX6SX fec support three rx ring1, the current driver lost to init
ring1 and ring2 maximum receive buffer size, that cause receving
frame date length error. The driver reports "rcv is not +last" error
log in user case.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use of well known RSS key might increase attack surface.

Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Govindarajulu Varadarajan <_govind@gmx.com>
Cc: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change has no functional impact and simply addresses some coding
style issues detected by checkpatch. Specifically this change
adjusts "if" statements which also include the assignment of a
variable.

No changes to the resultant object files result as determined by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

All the access to wq has been moved out of hardirq context. We no longer need to
use spin_lock_irqsave.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

enic_isr_legacy(), enic_isr_msix() & enic_isr_msi() run from hard
interrupt context.

They can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4_en_set_rxfh() can crash if no RSS indir table is provided.

While we are at it, allow RSS key to be changed with ethtool -X

Tested:

myhost:~# cat /proc/sys/net/core/netdev_rss_key
b6:89:91:f3:b2:c3:c2:90:11:e8:ce:45:e8:a9:9d:1c:f2:f6:d4:53:61:8b:26:3a:b3:9a:57:97:c3:b6:79:4d:2e:d9:66:5c:72:ed:b6:8e:c5:5d:4d:8c:22:67:30:ab:8a:6e:c3:6a

myhost:~# ethtool -x eth0
RX flow hash indirection table for eth0 with 8 RX ring(s):
    0:      0     1     2     3     4     5     6     7
RSS hash key:
b6:89:91:f3:b2:c3:c2:90:11:e8:ce:45:e8:a9:9d:1c:f2:f6:d4:53:61:8b:26:3a:b3:9a:57:97:c3:b6:79:4d:2e:d9:66:5c:72:ed:b6:8e

myhost:~# ethtool -X eth0 hkey \
03:0e:e2:43:fa:82:0e:73:14:2d:c0:68:21:9e:82:99:b9:84:d0:22:e2:b3:64:9f:4a:af:00:fa:cc:05:b4:4a:17:05:14:73:76:58:bd:2f

myhost:~# ethtool -x eth0
RX flow hash indirection table for eth0 with 8 RX ring(s):
    0:      0     1     2     3     4     5     6     7
RSS hash key:
03:0e:e2:43:fa:82:0e:73:14:2d:c0:68:21:9e:82:99:b9:84:d0:22:e2:b3:64:9f:4a:af:00:fa:cc:05:b4:4a:17:05:14:73:76:58:bd:2f
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: b9d1ab7e ("mlx4: use netdev_rss_key_fill() helper")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hariprasad Shenai says:

====================
RDMA/cxgb4,cxgb4vf,csiostor: Cleanup macros

This series continues to cleanup all the macros/register defines related to
filter, port, VI, queue, RSS, LDST, firmware, etc that are defined in t4fw_api.h
and the affected files.

Will post few more series so that we can cover all the macros so that they all
follow the same style to be consistent.

The patches series is created against 'net-next' tree.
And includes patches on cxgb4, cxgb4vf, iw_cxgb4 and csiostor driver.

We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch cleanups all PCIE, RSS & FW related macros/register defines that are
defined in t4fw_api.h and the affected files.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch cleanups all port and VI related macros/register defines that are
defined in t4fw_api.h and the affected files.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch cleanups all queue related macros/register defines that are defined
in t4fw_api.h and the affected files.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch cleanups PF/VF and LDST related macros/register defines that are
defined in t4fw_api.h and the affected files.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch cleanups all filter related macros/register defines that are defined
in t4fw_api.h and the affected files.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The original FDB code submission wasn't correct and the code
wasn't enabled.  This removes some dead code (can use the common kernel
code for fdb_del and fdb_dump) and correctly enables the fdb_add
function pointer.

The fdb_add functionality is important to i40e because it is needed
for a workaround to allow bridges to work correctly on the i40e
hardware.
Reported-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/ieee802154/fakehard.c

A bug fix went into 'net' for ieee802154/fakehard.c, which is removed
in 'net-next'.

Add build fix into the merge from Stephen Rothwell in openvswitch, the
logging macros take a new initial 'log' argument, a new call was added
in 'net' so when we merge that in here we have to explicitly add the
new 'log' arg to it else the build fails.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Fix BUG when decrypting empty packets in mac80211, from Ronald Wahl.

 2) nf_nat_range is not fully initialized and this is copied back to
    userspace, from Daniel Borkmann.

 3) Fix read past end of b uffer in netfilter ipset, also from Dan
    Carpenter.

 4) Signed integer overflow in ipv4 address mask creation helper
    inet_make_mask(), from Vincent BENAYOUN.

 5) VXLAN, be2net, mlx4_en, and qlcnic need ->ndo_gso_check() methods to
    properly describe the device's capabilities, from Joe Stringer.

 6) Fix memory leaks and checksum miscalculations in openvswitch, from
    Pravin B SHelar and Jesse Gross.

 7) FIB rules passes back ambiguous error code for unreachable routes,
    making behavior confusing for userspace.  Fix from Panu Matilainen.

 8) ieee802154fake_probe() doesn't release resources properly on error,
    from Alexey Khoroshilov.

 9) Fix skb_over_panic in add_grhead(), from Daniel Borkmann.

10) Fix access of stale slave pointers in bonding code, from Nikolay
    Aleksandrov.

11) Fix stack info leak in PPP pptp code, from Mathias Krause.

12) Cure locking bug in IPX stack, from Jiri Bohac.

13) Revert SKB fclone memory freeing optimization that is racey and can
    allow accesses to freed up memory, from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (71 commits)
  tcp: Restore RFC5961-compliant behavior for SYN packets
  net: Revert "net: avoid one atomic operation in skb_clone()"
  virtio-net: validate features during probe
  cxgb4 : Fix DCB priority groups being returned in wrong order
  ipx: fix locking regression in ipx_sendmsg and ipx_recvmsg
  openvswitch: Don't validate IPv6 label masks.
  pptp: fix stack info leak in pptp_getname()
  brcmfmac: don't include linux/unaligned/access_ok.h
  cxgb4i : Don't block unload/cxgb4 unload when remote closes TCP connection
  ipv6: delete protocol and unregister rtnetlink when cleanup
  net/mlx4_en: Add VXLAN ndo calls to the PF net device ops too
  bonding: fix curr_active_slave/carrier with loadbalance arp monitoring
  mac80211: minstrel_ht: fix a crash in rate sorting
  vxlan: Inline vxlan_gso_check().
  can: m_can: update to support CAN FD features
  can: m_can: fix incorrect error messages
  can: m_can: add missing delay after setting CCCR_INIT bit
  can: m_can: fix not set can_dlc for remote frame
  can: m_can: fix possible sleep in napi poll
  can: m_can: add missing message RAM initialization
  ...

Pull drm fixes from Dave Airlie:
 "Just two radeon and two intel fixes: endian and regression fixes"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon: fix endian swapping in vbios fetch for tdp table
  drm/radeon: disable native backlight control on pre-r6xx asics (v2)
  drm/i915: Kick fbdev before vgacon
  drm/i915: drop WaSetupGtModeTdRowDispatch:snb

Pull sound fixes from Takashi Iwai:
 "This batch ended up as a relatively high volume due to pending ASoC
  fixes.  But most of fixes there are trivial and/or device- specific
  fixes and quirks, so safe to apply.  The only (ASoC) core fixes are
  the DPCM race fix and the machine-driver matching fix for
  componentization"

* tag 'sound-3.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - fix the mic mute led problem for Latitude E5550
  ALSA: hda - move DELL_WMI_MIC_MUTE_LED to the tail in the quirk chain
  ASoC: wm_adsp: Avoid attempt to free buffers that might still be in use
  ALSA: usb-audio: Set the Control Selector to SU_SELECTOR_CONTROL for UAC2
  ALSA: usb-audio: Add ctrl message delay quirk for Marantz/Denon devices
  ASoC: sgtl5000: Fix SMALL_POP bit definition
  ASoC: cs42l51: re-hook of_match_table pointer
  ASoC: rt5670: change dapm routes of PLL connection
  ASoC: rt5670: correct the incorrect default values
  ASoC: samsung: Add MODULE_DEVICE_TABLE for Snow
  ASoC: max98090: Correct pclk divisor settings
  ASoC: dpcm: Fix race between FE/BE updates and trigger
  ASoC: Fix snd_soc_find_dai() matching component by name
  ASoC: rsnd: remove unsupported PAUSE flag
  ASoC: fsi: remove unsupported PAUSE flag
  ASoC: rt5645: Mark RT5645_TDM_CTRL_3 as readable
  ASoC: rockchip-i2s: fix infinite loop in rockchip_snd_rxctrl
  ASoC: es8328-i2c: Fix i2c_device_id name field in es8328_id
  ASoC: fsl_asrc: Add reg_defaults for regmap to fix kernel dump

Pull ACPI power management fix from Rafael Wysocki:
 "This is just a one-liner fixing a regression introduced in 3.13 that
  broke system suspend on some Chromebooks.

  On those machines there are ACPI device objects for some I2C devices
  that can wake up the system from sleep states, but that is done via a
  platform-specific mechanism and the ACPI objects don't contain any
  wakeup-related information.  When we started to use ACPI power
  management with those devices (which happened during the 3.13 cycle),
  their configuration confused the ACPI PM layer that returned error
  codes from suspend callbacks for them causing system suspend to fail.

  However, the ACPI PM layer can safely ignore the wakeup setting from a
  device driver if the ACPI object corresponding to the device in
  question doesn't contain wakeup information in which case the driver
  itself is responsible for setting up the device for system wakeup"

* tag 'pm+acpi-3.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / PM: Ignore wakeup setting if the ACPI companion can't wake up

Pull devicetree fixes from Rob Herring:
 "DeviceTree fixes for 3.18:

   - two fixes for OF selftest code
   - fix for PowerPC address parsing to disable work-around except on
     old PowerMACs
   - fix a crash when earlycon is enabled, but no device is found
   - DT documentation fixes and missing vendor prefixes

  All but the doc updates are also for stable"

* tag 'devicetree-fixes-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  of/selftest: Fix testing when /aliases is missing
  of/selftest: Fix off-by-one error in removal path
  documentation: pinctrl bindings: Fix trivial typo 'abitrary'
  devicetree: bindings: Add vendor prefix for Micron Technology, Inc.
  of: Add vendor prefix for Chips&Media, Inc.
  of/base: Fix PowerPC address parsing hack
  devicetree: vendor-prefixes.txt: fix whitespace
  of: Fix crash if an earlycon driver is not found
  of/irq: Drop obsolete 'interrupts' vs 'interrupts-extended' text
  of: Spelling s/stucture/structure/
  devicetree: bindings: add sandisk to the vendor prefixes

Pull PCI fixes from Bjorn Helgaas:
 "These are fixes for an issue with 64-bit PCI bus addresses on 32-bit
  PAE kernels, an APM X-Gene problem (it depended on a generic change we
  removed before merging), a fix for my hotplug device configuration
  changes, and a devicetree documentation update.

  Resource management:
    - Support 64-bit bridge windows if we have 64-bit dma_addr_t (Yinghai Lu)

  PCI device hotplug:
    - Apply _HPX Link Control settings to all devices with a link (Yinghai Lu)

  Generic host bridge driver:
    - Add DT binding for "linux,pci-domain" property (Lucas Stach)

  APM X-Gene:
    - Assign resources to bus before adding new devices (Duc Dang)"

* tag 'pci-v3.18-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Support 64-bit bridge windows if we have 64-bit dma_addr_t
  PCI: Apply _HPX Link Control settings to all devices with a link
  PCI: Add missing DT binding for "linux,pci-domain" property
  PCI: xgene: Assign resources to bus before adding new devices

Pull SCSI target fixes from Nicholas Bellinger:
 "Here are the target-pending fixes queued for v3.18-rc6.

  The highlights include:

   - target-core OOPs fix with tcm_qla2xxx + vxworks FC initiators +
     zero length SCSI commands having a transfer direction set.  (Roland
     + Craig Watson)

   - vhost-scsi OOPs fix to explicitly prevent WWPN endpoint configfs
     group removal while qemu still has an active reference.  (Paolo +
     nab)

   - ib_srpt fix for RDMA hardware with lower srp_sq_size limits.
     (Bart)

   - two ib_isert work-arounds for running on ocrdma hardware (Or + Sagi
     + Chris)

   - iscsi-target discovery portal typo + SPC-3 PR Preempt SA key
     matching fix (Steve)"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  IB/isert: Adjust CQ size to HW limits
  target: return CONFLICT only when SA key unmatched
  iser-target: Handle DEVICE_REMOVAL event on network portal listener correctly
  ib_isert: Add max_send_sge=2 minimum for control PDU responses
  srp-target: Retry when QP creation fails with ENOMEM
  iscsi-target: return the correct port in SendTargets
  vhost-scsi: Take configfs group dependency during VHOST_SCSI_SET_ENDPOINT
  target: Don't call TFO->write_pending if data_length == 0

Pull dmaengine fixes from Vinod Koul:
 "We have couple of fixes for dmaengine queued up:
   - dma mempcy fix for dma configuration of sun6i by Maxime
   - pl330 fixes: First the fixing allocation for data buffers by Liviu
     and then Jon's fixe for fifo width and usage"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: Fix allocation size for PL330 data buffer depth.
  dmaengine: pl330: Limit MFIFO usage for memcpy to avoid exhausting entries
  dmaengine: pl330: Align DMA memcpy operations to MFIFO width
  dmaengine: sun6i: Fix memcpy operation

Pull MIPS fixes from Ralf Baechle:
 "More 3.18 fixes for MIPS:

   - backtraces were not quite working on on 64-bit kernels
   - loongson needs a different cache coherency setting
   - Loongson 3 is a MIPS64 R2 version but due to erratum we treat is an
     older architecture revision.
   - fix build errors due to undefined references to __node_distances
     for certain configurations.
   - fix instruction decodig in the jump label code.
   - for certain configurations copy_{from,to}_user destroy the content
     of $3 so that register needs to be marked as clobbed by the calling
     code.
   - Hardware Table Walker fixes.
   - fill the delay slot of the last instruction of memcpy otherwise
     whatever ends up there randomly might have undesirable effects.
   - ensure get_user/__get_user always zero the variable to be read even
     in case of an error"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: jump_label.c: Handle the microMIPS J instruction encoding
  MIPS: jump_label.c: Correct the span of the J instruction
  MIPS: Zero variable read by get_user / __get_user in case of an error.
  MIPS: lib: memcpy: Restore NOP on delay slot before returning to caller
  MIPS: tlb-r4k: Add missing HTW stop/start sequences
  MIPS: asm: uaccess: Add v1 register to clobber list on EVA
  MIPS: oprofile: Fix backtrace on 64-bit kernel
  MIPS: Loongson: Set Loongson-3's ISA level to MIPS64R1
  MIPS: Loongson: Fix the write-combine CCA value setting
  MIPS: IP27: Fix __node_distances undefined error
  MIPS: Loongson3: Fix __node_distances undefined error

Pull powerpc fix from Michael Ellerman:
 "One fix from Scott, he says:

  This patch fixes a crash (introduced in v3.18-rc1) in the FSL MSI driver
  when threaded IRQs are enabled"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
  powerpc/fsl_msi: mark the msi cascade handler IRQF_NO_THREAD

Pull x86 fixes from Thomas Gleixner:
 "Misc fixes:
   - gold linker build fix
   - noxsave command line parsing fix
   - bugfix for NX setup
   - microcode resume path bug fix
   - _TIF_NOHZ versus TIF_NOHZ bugfix as discussed in the mysterious
     lockup thread"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, syscall: Fix _TIF_NOHZ handling in syscall_trace_enter_phase1
  x86, kaslr: Handle Gold linker for finding bss/brk
  x86, mm: Set NX across entire PMD at boot
  x86, microcode: Update BSPs microcode on resume
  x86: Require exact match for 'noxsave' command line option

Pull scheduler fixes from Ingo Molnar:
 "Misc fixes: two NUMA fixes, two cputime fixes and an RCU/lockdep fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/cputime: Fix clock_nanosleep()/clock_gettime() inconsistency
  sched/cputime: Fix cpu_timer_sample_group() double accounting
  sched/numa: Avoid selecting oneself as swap target
  sched/numa: Fix out of bounds read in sched_init_numa()
  sched: Remove lockdep check in sched_move_task()