This might trip up tx completion processing, although the condition that
triggers this should not (yet) occur in practice.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fixes a regression from commit
"ath9k: shrink a few data structures by reordering fields"

When cloning a buffer, the stale flag (part of bf_state now) needs to be
reset after copying the state to prevent tx processing hangs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add generic rule on encountering Belkin bluetooth usb device F8065bf.

Relevant section from /sys/kernel/debug/usb/devices:

T:  Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=050d ProdID=065a Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=0002723E2D29
C:* #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
Signed-off-by: Ken O'Brien <kernel@kenobrien.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

When the dlc is closed, rfcomm_dev_state_change() tries to release the
port in the case it cannot get a reference to the tty. However this is
racy and not even needed.

Infact as Peter Hurley points out:

1. Only consider dlcs that are 'stolen' from a connected socket, ie.
   reused. Allocated dlcs cannot have been closed prior to port
   activate and so for these dlcs a tty reference will always be avail
   in rfcomm_dev_state_change() -- except for the conditions covered by
   #2b below.
2. If a tty was at some point previously created for this rfcomm, then
   either
   (a) the tty reference is still avail, so rfcomm_dev_state_change()
       will perform a hangup. So nothing to do, or,
   (b) the tty reference is no longer avail, and the tty_port will be
       destroyed by the last tty_port_put() in rfcomm_tty_cleanup.
       Again, no action required.
3. Prior to obtaining the dlc lock in rfcomm_dev_add(),
   rfcomm_dev_state_change() will not 'see' a rfcomm_dev so nothing to
   do here.
4. After releasing the dlc lock in rfcomm_dev_add(),
   rfcomm_dev_state_change() will 'see' an incomplete rfcomm_dev if a
   tty reference could not be obtained. Again, the best thing to do here
   is nothing. Any future attempted open() will block on
   rfcomm_dev_carrier_raised(). The unconnected device will exist until
   released by ioctl(RFCOMMRELEASEDEV).

The patch removes the aforementioned code and uses the
tty_port_tty_hangup() helper to hangup the tty.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Pull networking fixes from David Miller:

 1) If the local_df boolean is set on an SKB we have to allocate a
    unique ID even if IP_DF is set in the ipv4 headers, from Ansis
    Atteka.

 2) Some fixups for the new chipset support that went into the sfc
    driver, from Ben Hutchings.

 3) Because SCTP bypasses a good chunk of, and actually duplicates, the
    logic of the ipv6 output path, some IPSEC things don't get done
    properly.  Integrate SCTP better into the ipv6 output path so that
    these problems are fixed and such issues don't get missed in the
    future either.  From Daniel Borkmann.

 4) Fix skge regressions added by the DMA mapping error return checking
    added in v3.10, from Mikulas Patocka.

 5) Kill some more IRQF_DISABLED references, from Michael Opdenacker.

 6) Fix races and deadlocks in the bridging code, from Hong Zhiguo.

 7) Fix error handling in tun_set_iff(), in particular don't leak
    resources.  From Jason Wang.

 8) Prevent format-string injection into xen-netback driver, from Kees
    Cook.

 9) Fix regression added to netpoll ARP packet handling, in particular
    check for the right ETH_P_ARP protocol code.  From Sonic Zhang.

10) Try to deal with AMD IOMMU errors when using r8169 chips, from
    Francois Romieu.

11) Cure freezes due to recent changes in the rt2x00 wireless driver,
    from Stanislaw Gruszka.

12) Don't do SPI transfers (which can sleep) in interrupt context in
    cw1200 driver, from Solomon Peachy.

13) Fix LEDs handling bug in 5720 tg3 chips already handled for 5719.
    From Nithin Sujir.

14) Make xen_netbk_count_skb_slots() count the actual number of slots
    that will be used, taking into consideration packing and other
    issues that the transmit path will run into.  From David Vrabel.

15) Use the correct maximum age when calculating the bridge
    message_age_timer, from Chris Healy.

16) Get rid of memory leaks in mcs7780 IRDA driver, from Alexey
    Khoroshilov.

17) Netfilter conntrack extensions were converted to RCU but are not
    always freed properly using kfree_rcu().  Fix from Michal Kubecek.

18) VF reset recovery not being done correctly in qlcnic driver, from
    Manish Chopra.

19) Fix inverted test in ATM nicstar driver, from Andy Shevchenko.

20) Missing workqueue destroy in cxgb4 error handling, from Wei Yang.

21) Internal switch not initialized properly in bgmac driver, from Rafał
    Miłecki.

22) Netlink messages report wrong local and remote addresses in IPv6
    tunneling, from Ding Zhi.

23) ICMP redirects should not generate socket errors in DCCP and SCTP.
    We're still working out how this should be handled for RAW and UDP
    sockets.  From Daniel Borkmann and Duan Jiong.

24) We've had several bugs wherein the network namespace's loopback
    device gets accessed after it is free'd, NULL it out so that we can
    catch these problems more readily.  From Eric W Biederman.

25) Fix regression in TCP RTO calculations, from Neal Cardwell.

26) Fix too early free of xen-netback network device when VIFs still
    exist.  From Paul Durrant.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
  netconsole: fix a deadlock with rtnl and netconsole's mutex
  netpoll: fix NULL pointer dereference in netpoll_cleanup
  skge: fix broken driver
  ip: generate unique IP identificator if local fragmentation is allowed
  ip: use ip_hdr() in __ip_make_skb() to retrieve IP header
  xen-netback: Don't destroy the netdev until the vif is shut down
  net:dccp: do not report ICMP redirects to user space
  cnic: Fix crash in cnic_bnx2x_service_kcq()
  bnx2x, cnic, bnx2i, bnx2fc: Fix bnx2i and bnx2fc regressions.
  vxlan: Avoid creating fdb entry with NULL destination
  tcp: fix RTO calculated from cached RTT
  drivers: net: phy: cicada.c: clears warning Use #include <linux/io.h> instead of <asm/io.h>
  net loopback: Set loopback_dev to NULL when freed
  batman-adv: set the TAG flag for the vid passed to BLA
  netfilter: nfnetlink_queue: use network skb for sequence adjustment
  net: sctp: rfc4443: do not report ICMP redirects to user space
  net: usb: cdc_ether: use usb.h macros whenever possible
  net: usb: cdc_ether: fix checkpatch errors and warnings
  net: usb: cdc_ether: Use wwan interface for Telit modules
  ip6_tunnels: raddr and laddr are inverted in nl msg
  ...

This bug was introduced by commit
7a163bfb ("netconsole: avoid a crash with
multiple sysfs writers"). In store_enabled() we have the following
sequence: acquire nt->mutex then rtnl, but in the netconsole netdev
notifier we have rtnl then nt->mutex effectively leading to a deadlock.
The NULL pointer dereference that the above commit tries to fix is
actually due to another bug in netpoll_cleanup(). This is fixed by dropping
the mutex from the netdev notifier as it's already protected by rtnl.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I've been hitting a NULL ptr deref while using netconsole because the
np->dev check and the pointer manipulation in netpoll_cleanup are done
without rtnl and the following sequence happens when having a netconsole
over a vlan and we remove the vlan while disabling the netconsole:
	CPU 1					CPU2
					removes vlan and calls the notifier
enters store_enabled(), calls
netdev_cleanup which checks np->dev
and then waits for rtnl
					executes the netconsole netdev
					release notifier making np->dev
					== NULL and releases rtnl
continues to dereference a member of
np->dev which at this point is == NULL
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch 136d8f37 broke the skge driver.
Note this part of the patch:
+               if (skge_rx_setup(skge, e, nskb, skge->rx_buf_size) < 0) {
+                       dev_kfree_skb(nskb);
+                       goto resubmit;
+               }
+
                pci_unmap_single(skge->hw->pdev,
                                 dma_unmap_addr(e, mapaddr),
                                 dma_unmap_len(e, maplen),
                                 PCI_DMA_FROMDEVICE);
                skb = e->skb;
                prefetch(skb->data);
-               skge_rx_setup(skge, e, nskb, skge->rx_buf_size);

The function skge_rx_setup modifies e->skb to point to the new skb. Thus,
after this change, the new buffer, not the old, is returned to the
networking stack.

This bug is present in kernels 3.11, 3.11.1 and 3.12-rc1. The patch should
be queued for 3.11-stable.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Vasiliy Glazov <vascom2@gmail.com>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If local fragmentation is allowed, then ip_select_ident() and
ip_select_ident_more() need to generate unique IDs to ensure
correct defragmentation on the peer.

For example, if IPsec (tunnel mode) has to encrypt large skbs
that have local_df bit set, then all IP fragments that belonged
to different ESP datagrams would have used the same identificator.
If one of these IP fragments would get lost or reordered, then
peer could possibly stitch together wrong IP fragments that did
not belong to the same datagram. This would lead to a packet loss
or data corruption.
Signed-off-by: Ansis Atteka <aatteka@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb->data already points to IP header, but for the sake of
consistency we can also use ip_hdr() to retrieve it.
Signed-off-by: Ansis Atteka <aatteka@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Without this patch, if a frontend cycles through states Closing
and Closed (which Windows frontends need to do) then the netdev
will be destroyed and requires re-invocation of hotplug scripts
to restore state before the frontend can move to Connected. Thus
when udev is not in use the backend gets stuck in InitWait.

With this patch, the netdev is left alone whilst the backend is
still online and is only de-registered and freed just prior to
destroying the vif (which is also nicely symmetrical with the
netdev allocation and registration being done during probe) so
no re-invocation of hotplug scripts is required.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull MIPS updates from Ralf Baechle:
 - Minor updates and fixes to the Octeon ethernet driver in staging
 - A fix to VGA_MAP_MEM() for 64 bit platforms
 - Fix a workaround for 74K/1074K processors
 - The symlink arch/mips/boot/dts/include/dt-bindings was pointing to a
   a file with a name ending in \n.  I think this may have been caused
   by a git bug with with patches sent by email
 - A build fix for VGA console on BCM1480-based systems
 - Fix PCI device access via "/sys/bus/pci/.../resource0" or similar
   work for Alchemy platforms
 - Fix potential data leak on MIPS R5 cores.  This doesn't add proper
   support for any R5 features, just ensures a kernel without such
   support will be secure to run
 - Adding a macros for the CP0 Config5 register to be used by the R5 fix
 - Make get_cycles() actually return something useful where possible
   This also requires a preparatory patch for performance sake
 - Fix a warning about the use of smp_processor_id() in preemptible
   code.  Again this includes a preparatory patch adding the
   infrastructure to be used by the actual patch
 - Finally remove pointless one-line comment

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Fix invalid symbolic link file
  MIPS: PCI: pci-bcm1480: Include missing vt.h header
  MIPS: Disable usermode switching of the FR bit for MIPS R5 CPUs.
  MIPS: Add MIPS R5 config5 register.
  MIPS: PCI: Use pci_resource_to_user to map pci memory space properly
  MIPS: 74K/1074K: Correct erratum workaround.
  MIPS: Cleanup CP0 PRId and CP1 FPIR register access masks
  MIPS: Remove useless comment about kprobe from arch/mips/Makefile
  MIPS: Fix VGA_MAP_MEM macro.
  MIPS: Reimplement get_cycles().
  MIPS: Optimize current_cpu_type() for better code.
  MIPS: Fix accessing to per-cpu data when flushing the cache
  MIPS: Provide nice way to access boot CPU's data.
  staging: octeon-ethernet: rgmii: enable interrupts that we can handle
  staging: octeon-ethernet: remove skb alloc failure warnings
  staging: octeon-ethernet: make dropped packets to consume NAPI budget

Pull ceph fixes from Sage Weil:
 "These fix several bugs with RBD from 3.11 that didn't get tested in
  time for the merge window: some error handling, a use-after-free, and
  a sequencing issue when unmapping and image races with a notify
  operation.

  There is also a patch fixing a problem with the new ceph + fscache
  code that just went in"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  fscache: check consistency does not decrement refcount
  rbd: fix error handling from rbd_snap_name()
  rbd: ignore unmapped snapshots that no longer exist
  rbd: fix use-after free of rbd_dev->disk
  rbd: make rbd_obj_notify_ack() synchronous
  rbd: complete notifies before cleaning up osd_client and rbd_dev
  libceph: add function to ensure notifies are complete

Commit 3b29aa5b [MIPS: add <dt-bindings/> symlink] created a symlink
file in include/dt-bindings.  Even though commit diff is fine, the symlink
is invalid and ls -lb shows a newline character at the end of the filename:

lrwxrwxrwx 1 maddy maddy 35 Sep 19 18:11 dt-bindings ->
../../../../../include/dt-bindings\n
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Cc: steven.hill@imgtec.com
Cc: mmarek@suse.cz
Cc: swarren@nvidia.com
Cc: linux-mips@linux-mips.org
Cc: linux-kbuild@vger.kernel.org
Cc: james.hogan@imgtec.com
Patchwork: https://patchwork.linux-mips.org/patch/5859/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

It's needed for the MAX_NR_CONSOLES macro.

Fixes the following build problem on a randconfig:

arch/mips/pci/pci-bcm1480.c: In function 'bcm1480_pcibios_init':
arch/mips/pci/pci-bcm1480.c:261:36: error: 'MAX_NR_CONSOLES'
undeclared (first use in this function)
arch/mips/pci/pci-bcm1480.c:261:36: note: each undeclared
identifier is reported only once for each function it appears in
make[1]: *** [arch/mips/pci/pci-bcm1480.o] Error 1
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5858/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Currently the kernel will always use the FR=0 register model for O32.  If
an O32 application did enable FR=1 mode, some data from another application
might be leaked in the extra registers becoming visible.

Iow, this patch is meant to make the kernel MIPS R5 tolerant but leaves
proper MIPS R5 support to a future patchset.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Pull drm radeon/nouveau/core fixes from Dave Airlie:
 "Mostly radeon fixes, with some nouveau bios parser, ttm fix and a fix
  for AST driver"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (42 commits)
  drm/fb-helper: don't sleep for screen unblank when an oops is in progress
  drm, ttm Fix uninitialized warning
  drm/ttm: fix the tt_populated check in ttm_tt_destroy()
  drm/nouveau/ttm: prevent double-free in nouveau_sgdma_create_ttm() failure path
  drm/nouveau/bios/init: fix thinko in INIT_CONFIGURE_MEM
  drm/nouveau/kms: enable for non-vga pci classes
  drm/nouveau/bios/init: stub opcode 0xaa
  drm/radeon: avoid UVD corruptions on AGP cards
  drm/radeon: fix panel scaling with eDP and LVDS bridges
  drm/radeon/dpm: rework auto performance level enable
  drm/radeon: Fix hmdi typo
  drm/radeon/dpm/rs780: fix force_performance state for same sclks
  drm/radeon/dpm/rs780: don't enable sclk scaling if not required
  drm/radeon/dpm/rs780: add some sanity checking to sclk scaling
  drm/radeon/dpm/rs780: use drm_mode_vrefresh()
  drm/udl: rip out set_need_resched
  drm/ast: fix the ast open key function
  drm/radeon/dpm: add bapm callback for kb/kv
  drm/radeon/dpm: add bapm callback for trinity
  drm/radeon/dpm: add infrastructure to properly handle bapm
  ...

Otherwise the system will burn even brighter and worse, leave the user
wondering what's going on exactly.

Since we already have a panic handler which will (try) to restore the
entire fbdev console mode, we can just bail out.  Inspired by a patch from
Konstantin Khlebnikov.  The callchain leading to this, cut&pasted from
Konstantin's original patch:

callstack:
panic()
bust_spinlocks(1)
unblank_screen()
vc->vc_sw->con_blank()
fbcon_blank()
fb_blank()
info->fbops->fb_blank()
drm_fb_helper_blank()
drm_fb_helper_dpms()
drm_modeset_lock_all()
mutex_lock(&dev->mode_config.mutex)

Note that the entire locking in the fb helper around panic/sysrq and kdbg
is ...  non-existant.  So we have a decent change of blowing up
everything.  But since reworking this ties in with funny concepts like the
fbdev notifier chain or the impressive things which happen around
console_lock while oopsing, I'll leave that as an exercise for braver
souls than me.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Dave Airlie <airlied@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Fix uninitialized warning.

drivers/gpu/drm/ttm/ttm_object.c: In function ‘ttm_base_object_lookup’:
drivers/gpu/drm/ttm/ttm_object.c:213:10: error: ‘base’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
  kref_put(&base->refcount, ttm_release_base);
          ^
drivers/gpu/drm/ttm/ttm_object.c:221:26: note: ‘base’ was declared here
  struct ttm_base_object *base;
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

After a vmalloc failure in ttm_dma_tt_alloc_page_directory(),
ttm_dma_tt_init() will call ttm_tt_destroy() to cleanup, and end up
inside the driver's unpopulate() hook when populate() has never yet
been called.

On nouveau, the first issue to be hit because of this is that
dma_address[] may be a NULL pointer.  After working around this,
ttm_pool_unpopulate() may potentially hit the same issue with
the pages[] array.

It seems to make more sense to avoid calling unpopulate on already
unpopulated TTMs than to add checks to all the implementations.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Cc: stable@vger.kernel.org
Cc: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Merge branch 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes

A couple of bios parser fixes (one for ancient chips, another for new ones - important in Optimus configs).  Another to make sure KMS is enabled on certain Optimus configs, and a TTM failure path fix.

* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
  drm/nouveau/ttm: prevent double-free in nouveau_sgdma_create_ttm() failure path
  drm/nouveau/bios/init: fix thinko in INIT_CONFIGURE_MEM
  drm/nouveau/kms: enable for non-vga pci classes
  drm/nouveau/bios/init: stub opcode 0xaa

Pull vfs fixes from Al Viro:
 "atomic_open-related fixes (Miklos' series, with EEXIST-related parts
  replaced with fix in fs/namei.c:atomic_open() instead of messing with
  the instances) + race fix in autofs + leak on failure exit in 9p"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  9p: don't forget to destroy inode cache if fscache registration fails
  atomic_open: take care of EEXIST in no-open case with O_CREAT|O_EXCL in fs/namei.c
  vfs: don't set FILE_CREATED before calling ->atomic_open()
  nfs: set FILE_CREATED
  gfs2: set FILE_CREATED
  cifs: fix filp leak in cifs_atomic_open()
  vfs: improve i_op->atomic_open() documentation
  autofs4: close the races around autofs4_notify_daemon()

[ralf@linux-mips.org: This only matters to Alchemy platforms.  On other
platforms fixup_bigphys_addr is just an identidy mapping.]
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Cc: tiejun.chen <tiejun.chen@windriver.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1868/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Make sure 74K revision numbers are not applied to the 1074K.  Also catch
invalid usage.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5857/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Replace hardcoded CP0 PRId and CP1 FPIR register access masks throughout.
The change does not touch places that use shifted or partial masks.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5838/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Pull pstore/compression fixes from Tony Luck:
 "Three pstore fixes related to compression:
   1) Better adjustment of size of compression buffer (was too big for
      EFIVARS backend resulting in compression failure
   2) Use zlib_inflateInit2 instead of zlib_inflateInit
   3) Don't print messages about compression failure.  They will waste
      space that may better be used to log console output leading to the
      crash"

* tag 'please-pull-pstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
  pstore: Remove the messages related to compression failure
  pstore: Use zlib_inflateInit2 instead of zlib_inflateInit
  pstore: Adjust buffer size for compression for smaller registered buffers

We need to let the setup stage complete cleanly even when the HCI device
is rfkilled. Otherwise the HCI device will stay in an undefined state
and never get notified to user space through mgmt (even when it gets
unblocked through rfkill).

This patch makes sure that hci_dev_open() can be called in the HCI_SETUP
stage, that blocking the device doesn't abort the setup stage, and that
the device gets proper powered down as soon as the setup stage completes
in case it was blocked meanwhile.

The bug that this patch fixed can be very easily reproduced using e.g.
the rfkill command line too. By running "rfkill block all" before
inserting a Bluetooth dongle the resulting HCI device goes into a state
where it is never announced over mgmt, not even when "rfkill unblock all"
is run.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

This makes it more convenient to check for rfkill (no need to check for
dev->rfkill before calling rfkill_blocked()) and also avoids potential
races if the RFKILL state needs to be checked from within the rfkill
callback.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

The commit c1bf207d (kernel.org) rsp.
58e9ad32a48dce37ffeea912f55bd1c94b85ad7f (lmo) [MIPS: kprobe: Add support]
introduced a useless comment.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: David Daney <ddaney@caviumnetworks.com>
Patchwork: https://patchwork.linux-mips.org/patch/1765/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

DCCP shouldn't be setting sk_err on redirects as it
isn't an error condition. it should be doing exactly
what tcp is doing and leaving the error handler without
touching the socket.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull x86 fixes from Ingo Molnar:
 "Misc fixes"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/intel/lpss: Add pin control support to Intel low power subsystem
  perf/x86/intel: Mark MEM_LOAD_UOPS_MISS_RETIRED as precise on SNB
  x86: Remove now-unused save_rest()
  x86/smpboot: Fix announce_cpu() to printk() the last "OK" properly

Pull timer fix from Ingo Molnar:
 "An NTP related lockup fix"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping: Fix HRTICK related deadlock from ntp lock changes

commit 104a43ed
    cnic: Use CHIP_NUM macros from bnx2x.h

changed the code to use the bnx2x macro NO_FCOE() to determine if FCoE
is supported or not.  There is another place in cnic that is still using
the old method to determine if FCoE is supported or not.  The 2 methods
may not yield the same result after the network interface is brought down
and up.  This will cause the crash as cnic_bnx2x_service_kcq() will access
the uninitialized cp->kcq2.

The fix is to consistently use the same macro CNIC_SUPPORTS_FCOE() which
uses the bnx2x NO_FCOE() macro.  As a follow-up, we can clean up the code
to remove the old method as it is no longer needed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit b9871bcf
    bnx2x: VF RSS support - PF side

changed the configuration of the doorbell HW and it broke iSCSI and FCoE.
We fix this by making compatible changes to the doorbell address in bnx2i
and bnx2fc.  For the userspace driver, we need to pass a modified CID
so that the existing userspace driver will calculate the correct doorbell
address and continue to work.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull scheduler fixes from Ingo Molnar:
 "Misc fixes"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Fix comment for sched_info_depart
  sched/Documentation: Update sched-design-CFS.txt documentation
  sched/debug: Take PID namespace into account
  sched/fair: Fix small race where child->se.parent,cfs_rq might point to invalid ones

Pull perf fixes from Ingo Molnar:
 "Two small fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Fix UAPI export of PERF_EVENT_IOC_ID
  perf/x86/intel: Fix Silvermont offcore masks

Included change:
- fix the Bridge Loop Avoidance component by marking the variables containing
  the VLAN ID with the HAS_TAG flag when needed.

Use the CKSEG1ADDR macro when calculating VGA_MAP_MEM.

[ralf@linux-mips.org: Include <asm/addrspace.h for CKSEG1ADDR.]
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5814/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>