Some component drivers will need to be able to look up their
DAI link substream and RTD data. Provide a mechanism for this.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch allows DPCM to dynamically alter the FE to BE PCM links
at runtime based on mixer setting updates. DAPM is looked up after
every mixer update and we perform a DPCM runtime update if the
mixer has a change of value.

This patchs adds/changes the following :-

 o Adds DPCM runtime update core.
 o Changes soc_dapm_mixer_update_power() and soc_dapm_mux_update_power()
   to return if a change has occured rather than 0. No other users check
   atm.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Add debugFS files for DPCM link management information.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The Dynamic PCM core allows digital audio data to be dynamically
routed between different ALSA PCMs and DAI links on SoC CPUs with
on chip DSP devices. e.g. audio data could be played on pcm:0,0 and
routed to any (or all) SoC DAI links.

Dynamic PCM introduces the concept of Front End (FE) PCMs and Back
End (BE) PCMs. The FE PCMs are normal ALSA PCM devices except that
they can dynamically route digital audio data to any supported BE
PCM. A BE PCM has no ALSA device, but represents a DAI link and it's
substream and audio HW parameters.

e.g. pcm:0,0 routing digital data to 2 external codecs.

FE pcm:0,0  ----> BE (McBSP.0) ----> CODEC 0
             +--> BE (McPDM.0) ----> CODEC 1

e.g. pcm:0,0 and pcm:0,1 routing digital data to 1 external codec.

FE pcm:0,0 ---
             +--> BE (McBSP.0) ----> CODEC
FE pcm:0,1 ---

The digital audio routing is controlled by the usual ALSA method
of mixer kcontrols. Dynamic PCM uses a DAPM graph to work out the
routing based upon the mixer settings and configures the BE PCMs
based on routing and the FE HW params.

DPCM is designed so that most ASoC component drivers will need no
modification at all. It's intended that existing CODEC, DAI and
platform drivers can be used in DPCM based audio devices without
any changes. However, there will be some cases where minor changes
are required (e.g. for very tightly coupled HW) and there are
helpers to support this too.

Somethimes the HW params of a FE and BE do not match or are
incompatible, so in these cases the machine driver can reconfigure
any hw_params and make any DSP perform sample rate / format conversion.

This patch adds the core DPCM code and contains :-

 o The FE and BE PCM operations.
 o FE and BE DAI link support.
 o FE and BE PCM creation.
 o BE support API.
 o BE and FE link management.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

commit 4183eed2 (ASoC: core: Add signed multi register control) introduced
the variable 'min',but it is not used.

Remove it to fix the following build warning:

sound/soc/soc-core.c: In function 'snd_soc_put_xr_sx':
sound/soc/soc-core.c:2990: warning: unused variable 'min'
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Mostly a one to one converion. On one occasion the patch replaces a
snd_soc_read-snd_soc_write sequence with regmap_update_bits though as it helps
to keep the conversion simple.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

We have never really updated that version number and probably never will, so
just remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Not all advertised rates are available for all sysclk frequencies. Add
additional sysclk based rate constraints.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The sysclock is fixed, so just set it up once in the init callback instead of
setting it repeatably in the hw_params callback.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

If FLL bypass is left enabled when we disable the CODEC then the output
clock will be left running which consumes a small amount of additional
current. Only enable bypass when there is an output.
Signed-off-by: Kyung-Kwee Ryu <Kyung-Kwee.Ryu@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Added support for a control that strobes a bit in
a register to high then back to low (or the inverse).

This is typically useful for hardware that requires
strobing a singe bit to trigger some functionality
and where exposing the bit in a normal single control
would require the user to first manually set then
again unset the bit again for the strobe to trigger.

Added convenience macro.

SOC_SINGLE_STROBE

Added accessor implementations.

snd_soc_get_strobe
snd_soc_put_strobe
Signed-off-by: Kristoffer KARLSSON <kristoffer.karlsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Added control type that can span multiple consecutive codec registers
forming a single signed value in a MSB/LSB manner.
The control dynamically adjusts to the register word size configured
in driver.

Added convenience macro.

SOC_SINGLE_XR_SX

Added accessor implementations.

snd_soc_info_xr_sx
snd_soc_get_xr_sx
snd_soc_put_xr_sx
Signed-off-by: Kristoffer KARLSSON <kristoffer.karlsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

While reading through sound/soc/codecs/wm8994.c I noticed a fair
amount of trailing whitespace. This patch gets rid of it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Fixes the following build warning on x86_64.

In file included from include/trace/ftrace.h:567:0,
                 from include/trace/define_trace.h:86,
                 from include/trace/events/asoc.h:410,
                 from sound/soc/soc-core.c:45:
include/trace/events/asoc.h: In function 'ftrace_raw_event_snd_soc_dapm_output_path':
include/trace/events/asoc.h:246:1: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
include/trace/events/asoc.h: In function 'ftrace_raw_event_snd_soc_dapm_input_path':
include/trace/events/asoc.h:275:1: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The Springbank module can support a range of sample rates, selected at
runtime via GPIO configuration. Allow these to be configured at runtime.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Springbank can support stereo, though it is primarily intended for mono
use cases.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

In preparation for ASoC DSP support.

Add a DAPM API call to determine whether a DAPM audio path is valid between
source and sink widgets. This also takes into account all kcontrol mux and mixer
settings in between the source and sink widgets to validate the audio path.

This will be used by the DSP core to determine the runtime DAI mappings
between FE and BE DAIs in order to run PCM operations.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Connect the WM1250-EV1 baseband simulator on Littlemill systems up to
the CODEC AIF2 using the new CODEC<->CODEC link support, allowing a wider
range of use cases to be represented.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Since AIF3 shares clock signals with other audio interfaces in order to
ensure it doesn't drive undesirable clocks we need to tristate it. Rather
than forcing the machine driver to do so have the driver do this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch converts multiple if conditions in to single if with "&&"s.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Current DA7210 driver does support PLL mode fully. It uses fixed
value of input master clock and PLL mode is enabled and disabled based
on the sampling frequency being used for playback or recording. It also
doesn't support Sample Rate Measurement feature of DA7210 hardware.

This patch adds full support for PLL and SRM. Basically following three
modes of operation are possible for DA7210 hardware,

(1) I2S SLAVE mode with PLL bypassed
(2) I2S SLAVE mode with PLL enabled
(3) I2S Master mode with PLL enabled

This patch adds support for all three modes. Also, in case of SLAVE mode
with PLL, it supports SRM (Sample Rate Measurement) feature of the chip.

Actually this patch was submitted earlier and received some review
comments, but after that the driver got update by other patches. Because
of that, I am considering this as new patch and not versioning it based
of previous patches. This version tries to take care of all review
comments received for earlier submissions.
Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Linux 3.4-rc3 contains a bunch of Tegra changes which are conflicting
annoyingly with the new development that's going on for Tegra so merge
it up to resolve those conflicts.

Conflicts:
	sound/soc/soc-core.c
	sound/soc/tegra/tegra_i2s.c
	sound/soc/tegra/tegra_spdif.c

Fix the following build warning:

sound/soc/soc-dapm.c: In function 'snd_soc_dai_link_event':
sound/soc/soc-dapm.c:2913: warning: format '%lx' expects type 'long unsigned int', but argument 3 has type 'u64'

'%llx' should be used with 'u64' type.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Rather than having the user half start a stream but avoid any DMA to
trigger data flow on links which don't pass through the CPU create a
DAPM route between the two DAI widgets using a hw_params configuration
provided by the machine driver with the new 'params' member of the
dai_link struct.  If no configuration is provided in the dai_link then
use the old style even for CODEC<->CODEC links to avoid breaking
systems.

This greatly simplifies the userspace usage of such links, making them
as simple as analogue connections with the stream configuration being
completely transparent to them.

This is achieved by defining a new dai_link widget type which is created
when CODECs are linked and triggering the configuration of the link via
the normal PCM operations from there.  It is expected that the bias
level callbacks will be used for clock configuration.

Currently only the DAI format, rate and channel count can be configured
and currently the only DAI operations which can be called are hw_params
and digital_mute().  This corresponds well to the majority of CODEC
drivers which only use other callbacks for constraint setting but there
is obviously much room for extension here.  We can't simply call
hw_params() on startup as things like the system clocking configuration
may change at runtime and in future it will be desirable to offer some
configurability of the link parameters.

At present we are also restricted to a single DAPM link for the entire
DAI.  Once we have better support for channel mapping it would also be
desirable to extend this feature so that we can propagate per-channel
power state over the link.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

We should always have a CODEC already there when registering a CODEC DAI
and for CODEC<->CODEC links a dai_link will have two CODECs so it's much
simpler to do things at registration time.

This results in a slight change in the error handling for failed CODEC
DAI registrations but practically speaking these are never supposed to
fail so there shouldn't be much issue. The change is that we don't fail
the overall CODEC registration if the DAI registration fails; this seems
more robust anyway as we may not need to use a given DAI in a particular
system.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

When two CODEC DAIs are linked directly to each other then if we give the
same master mode settings to both devices things won't work as either
neither will drive or they'll drive against each other. Flip the settings
for the DAI in the CPU slot of the DAI link.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

In order to allow CODEC<->CODEC links to function we will need to allow
DAPM paths to be created that pass through DAIs rather than only ones
that are source or sunk at the DAI.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

This helps us ignore errors in callers if the operation failed due to not
being available as opposed to an error.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Pull ARM fixes from Russell King:
 "Nothing too disasterous, the biggest thing being the removal of the
  regulator support for vcore in the AMBA driver; only one SoC was using
  this and it got broken during the last merge window, which then
  started causing problems for other people.  Mutual agreement was
  reached for it to be removed."

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7386/1: jump_label: fixup for rename to static_key
  ARM: 7384/1: ThumbEE: Disable userspace TEEHBR access for !CONFIG_ARM_THUMBEE
  ARM: 7382/1: mm: truncate memory banks to fit in 4GB space for classic MMU
  ARM: 7359/2: smp_twd: Only wait for reprogramming on active cpus
  ARM: 7383/1: nommu: populate vectors page from paging_init
  ARM: 7381/1: nommu: fix typo in mm/Kconfig
  ARM: 7380/1: DT: do not add a zero-sized memory property
  ARM: 7379/1: DT: fix atags_to_fdt() second call site
  ARM: 7366/3: amba: Remove AMBA level regulator support
  ARM: 7377/1: vic: re-read status register before dispatching each IRQ handler
  ARM: 7368/1: fault.c: correct how the tsk->[maj|min]_flt gets incremented

The 'max' range needs to be unsigned, since the size of the user address
space is bigger than 2GB.

We know that 'count' is positive in 'long' (that is checked in the
caller), so we will truncate 'max' down to something that fits in a
signed long, but before we actually do that, that comparison needs to be
done in unsigned.

Bug introduced in commit 92ae03f2 ("x86: merge 32/64-bit versions of
'strncpy_from_user()' and speed it up").  On x86-64 you can't trigger
this, since the user address space is much smaller than 63 bits, and on
x86-32 it works in practice, since you would seldom hit the strncpy
limits anyway.

I had actually tested the corner-cases, I had only tested them on
x86-64.  Besides, I had only worried about the case of a pointer *close*
to the end of the address space, rather than really far away from it ;)

This also changes the "we hit the user-specified maximum" to return
'res', for the trivial reason that gcc seems to generate better code
that way.  'res' and 'count' are the same in that case, so it really
doesn't matter which one we return.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

c5905afb ("static keys: Introduce 'struct static_key'...") renamed
struct jump_label_key to struct static_key.  Fixup ARM for this to
eliminate these build warnings:

  include/linux/jump_label.h:113:2:
  warning: passing argument 1 of 'arch_static_branch' from incompatible pointer type
  include/asm/jump_label.h:17:82:
  note: expected 'struct jump_label_key *' but argument is of type 'struct static_key *'
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Currently when ThumbEE is not enabled (!CONFIG_ARM_THUMBEE) the ThumbEE
register states are not saved/restored at context switch. The default state
of the ThumbEE Ctrl register (TEECR) allows userspace accesses to the
ThumbEE Base Handler register (TEEHBR). This can cause unexpected behaviour
when people use ThumbEE on !CONFIG_ARM_THUMBEE kernels, as well as allowing
covert communication - eg between userspace tasks running inside chroot
jails.

This patch sets up TEECR in order to prevent user-space access to TEEHBR
when !CONFIG_ARM_THUMBEE. In this case, tasks are sent SIGILL if they try to
access TEEHBR.

Cc: stable@vger.kernel.org
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jonathan Austin <jonathan.austin@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

If a bank of memory spanning the 4GB boundary is added on a !CONFIG_LPAE
kernel then we will hang early during boot since the memory bank will
have wrapped around to zero.

This patch truncates memory banks for !LPAE configurations when the end
address is not representable in 32 bits.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

During booting of cpu1, there is a short window where cpu1
is online, but not active where cpu1 is occupied by waiting
to become active. If cpu0 then decides to schedule something
on cpu1 and wait for it to complete, before cpu0 has set
cpu1 active, we have a deadlock.

Typically it's this CPU frequency transition that happens at
this time, so let's just not wait for it to happen, it will
happen whenever the CPU eventually comes online instead.

Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Commit 26f41062 ("PCI: check for pci bar restore completion and
retry") attempted to address problems with PCI BAR restoration on
systems where FLR had not been completed before pci_restore_state() was
called, but it did that in an utterly wrong way.

First off, instead of retrying the writes for the BAR registers only, it
did that for all of the PCI config space of the device, including the
status register (whose value after the write quite obviously need not be
the same as the written one).  Second, it added arbitrary delay to
pci_restore_state() even for systems where the PCI config space
restoration was successful at first attempt.  Finally, the mdelay(10) it
added to every iteration of the writing loop was way too much of a delay
for any reasonable device.

All of this actually caused resume failures for some devices on Mikko's
system.

To fix the regression, make pci_restore_state() only retry the writes
for BAR registers and only wait if the first read from the register
doesn't return the written value.  Additionaly, make it wait for 1 ms,
instead of 10 ms, after every failing attempt to write into config
space.
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull "ARM: a few more SoC fixes for 3.4-rc" from Olof Johansson:
 - A handful of warning and build fixes for Qualcomm MSM
 - Build/warning and bug fixes for Samsung Exynos
 - A fix from Rob Herring that removes misplaced interrupt-parent
   properties from a few device trees
 - A fix to OMAP dealing with cpufreq build errors, removing some of the
   offending code since it was redundant anyway

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: OMAP: clock: cleanup CPUfreq leftovers, fix build errors
  ARM: dts: remove blank interrupt-parent properties
  ARM: EXYNOS: Fix Kconfig dependencies for device tree enabled machine files
  ARM: EXYNOS: Remove broken config values for touchscren for NURI board
  ARM: EXYNOS: set fix xusbxti clock for NURI and Universal210 boards
  ARM: EXYNOS: fix regulator name for NURI board
  ARM: SAMSUNG: make SAMSUNG_PM_DEBUG select DEBUG_LL
  ARM: msm: Fix section mismatches in proc_comm.c
  video: msm: Fix section mismatches in mddi.c
  arm: msm: trout: fix compile failure
  arm: msm: halibut: remove unneeded fixup
  ARM: EXYNOS: Add PDMA and MDMA physical base address defines
  ARM: S5PV210: Fix compiler warning in dma.c file
  ARM: EXYNOS: Fix compile error in exynos5250-cpufreq.c
  ARM: EXYNOS: Add missing definition for IRQ_I2S0
  ARM: S5PV210: fix unused LDO supply field from wm8994_pdata

Pull another round of sound fixes from Takashi Iwai:
 "A few regression fixes for Realtek HD-audio codecs, mainly specific to
  some laptop models."

* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/realtek - Fix mem leak (and rid us of trailing whitespace).
  ALSA: hda/realtek - Add quirk for Mac Pro 5,1 machines
  ALSA: hda/realtek - Add a fixup entry for Acer Aspire 8940G
  ALSA: hda/realtek - Fix GPIO1 setup for Acer Aspire 4930 & co
  ALSA: hda/realtek - Add a few ALC882 model strings back