Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

RCU api had been completed and rcu_access_pointer() or
rcu_dereference_protected() are better than generic
rcu_dereference_raw()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the artificial HZ latency on arp resolution.

Instead of firing a timer in one jiffy (up to 10 ms if HZ=100), lets
send the ARP message immediately.

Before patch :

# arp -d 192.168.20.108 ; ping -c 3 192.168.20.108
PING 192.168.20.108 (192.168.20.108) 56(84) bytes of data.
64 bytes from 192.168.20.108: icmp_seq=1 ttl=64 time=9.91 ms
64 bytes from 192.168.20.108: icmp_seq=2 ttl=64 time=0.065 ms
64 bytes from 192.168.20.108: icmp_seq=3 ttl=64 time=0.061 ms

After patch :

$ arp -d 192.168.20.108 ; ping -c 3 192.168.20.108
PING 192.168.20.108 (192.168.20.108) 56(84) bytes of data.
64 bytes from 192.168.20.108: icmp_seq=1 ttl=64 time=0.152 ms
64 bytes from 192.168.20.108: icmp_seq=2 ttl=64 time=0.064 ms
64 bytes from 192.168.20.108: icmp_seq=3 ttl=64 time=0.074 ms
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Error comes from commit ac124ff9
(be2net: cleanup and refactor stats code)

ERROR: "__udivdi3" [drivers/net/benet/be2net.ko] undefined!
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the Toshiba ethernet drivers into drivers/net/ethernet/toshiba
and make the necessary Kconfig and Makefile changes.

CC: Geoff Levand <geoff@infradead.org>
CC: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
CC: Ishizaki Kou <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the Micrel drivers into drivers/net/ethernet/micrel/ and
make the necessary Kconfig and Makefile changes.

CC: Ben Dooks <ben@simtec.co.uk>
CC: Tristram Ha <Tristram.Ha@micrel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the Freescale drivers into drivers/net/ethernet/freescale/ and
make the necessary Kconfig and Makefile changes.

CC: Sandeep Gopalpet <sandeep.kumar@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
CC: Shlomi Gridish <gridish@freescale.com>
CC: Li Yang <leoli@freescale.com>
CC: Pantelis Antoniou <pantelis.antoniou@gmail.com>
CC: Vitaly Bordug <vbordug@ru.mvista.com>
CC: Dan Malek <dmalek@jlc.net>
CC: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the Allied Telesis/Fujitsu drivers into drivers/net/ethernet/fujitsu/
and make the necessary Kconfig and Makefile changes.

CC: Shingo Fujimoto <shingo@flab.fujitsu.co.jp>
CC: Yutaka Tamiya <tamy@flab.fujitsu.co.jp>
CC: Rene Schmit <rene@bss.lu>
CC: Mika Kuoppala <miku@iki.fi>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the VIA drivers into drivers/net/ethernet/via/ and make the
necessary Kconfig and Makefile changes.

CC: Roger Luethi <rl@hellgate.ch>
CC: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the Marvell Ethernet drivers into drivers/net/ethernet/marvell/
and make the necessary Kconfig and Makefile changes.

CC: Sachin Sanap <ssanap@marvell.com>
CC: Zhangfei Gao <zgao6@marvell.com>
CC: Philip Rakity <prakity@marvell.com>
CC: Mark Brown <markb@marvell.com>
CC: Lennert Buytenhek <buytenh@marvell.com>
CC: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the OKI Semiconductor driver into driver/net/ethernet/oki-semi/
and make the necessary Kconfig and Makefile changes.

Note: there is no documented maintainer for this driver, so I CC'd
the last 2 major contributors.

CC: Tomoya <tomoya-linux@dsn.okisemi.com>
CC: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the drivers that use SEEQ chipset into drivers/net/ethernet/seeq
and make the necessary Kconfig and Makefile changes.

CC: Russell King <linux@arm.linux.org.uk>
CC: Hamish Coleman <hamish@zot.apana.org.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the SGI drivers into drivers/net/ethernet/sgi/ and make the
necessary Kconfig and Makefile changes.

CC: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the DEC - Tulip driver into drivers/net/ethernet/dec/tulip/
and make the necessary Kconfig and Makefile changes.

The Digital Equioment (DEC) driver ewrk3 was moved into
drivers/net/ethernet/dec/ and the remaining drivers (Tulip)
were moved into drivers/net/ethernet/dec/tulip/

CC: Tobias Ringstrom <tori@unhappy.mine.nu>
CC: Grant Grundler <grundler@parisc-linux.org>
CC: David Davies <davies@maniac.ultranet.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>

Both Spider net driver and Sun GEM driver use the sungem_phy.o object.
This fix creates a Kconfig object for sungem_phy (like MDIO) so that
both drivers require the SUNGEM_PHY object.

This has been compile tested for the Sun GEM driver.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the Atheros drivers into drivers/net/ethernet/atheros/ and
make the necessary Kconfig and Makefile changes.

CC: Jay Cliburn <jcliburn@gmail.com>
CC: Chris Snook <chris.snook@gmail.com>
CC: Jie Yang <jie.yang@atheros.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the D-Link drivers into drivers/net/ethernet/dlink/ and
make the necessary Kconfig and Makefile changes.

CC: Bjorn Ekwall <bj0rn@blox.se>
CC: Donald Becker <becker@scyld.com>
CC: Edward Peng <edward_peng@dlink.com.tw>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the Realtek drivers into drivers/net/ethernet/realtek/ and make
the necessary Kconfig and Makefile changes.

CC: Realtek linux nic maintainers <nic_swsd@realtek.com>
CC: Francois Romieu <romieu@fr.zoreil.com>
CC: Jeff Garzik <jgarzik@pobox.com>
CC: Donald Becker <becker@scyld.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the Faraday driver into drivers/net/ethernet/faraday/ and
make the necessary Kconfig and Makefile changes.

CC: "Po-Yu Chuang" <ratbert@faraday-tech.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Po-Yu Chuang <ratbert@faraday-tech.com>

Move the Intel XScale IXP drivers into drivers/net/ethernet/xscale/
and make the necessary Kconfig and Makefile changes.

CC: Krzysztof Halasa <khc@pm.waw.pl>
CC: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the National Semi-conductor drivers into drivers/net/ethernet/natsemi/
and make the necessary Kconfig and Makefile changes.  Also moved the 8390
(National Semi-conductor) devices as a sub-menu of National Semi-conductor
devices.

- moved the ibmlana driver as well into this directory since it is a
  "SONIC" driver

CC: Alfred Arnold <alfred.arnold@lancom.de>
CC: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
CC: Harald Welte <laforge@gnumonks.org>
CC: Tim Hockin <thockin@hockin.org>
CC: <linux-ns83820@kvack.org>
CC: Kevin Chea <kchea@yahoo.com>
CC: Marc Gauthier <marc@linux-xtensa.org>
CC: Chris Zankel <chris@zankel.net>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Marc Gauthier <marc@tensilica.com>

Move the Apple drivers into driver/net/ethernet/apple/ and make the
necessary Kconfig and Makefile changes.

CC: Paul Mackerras <paulus@samba.org>
CC: Paul Mackerras <paulus@au.ibm.com>
CC: Russell Nelson <nelson@crynwr.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the STMicroelectronics driver into driver/net/ethernet/stmicro/ and
make the necessary Kconfig and Makefile changes.

CC: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the Tehuti driver into drivers/net/ethernet/tehuti/ and
make the necessary Kconfig and Makefile changes.

CC: Alexander Indenbaum <baum@tehutinetworks.net>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the PA Semi driver into drivers/net/ethernet/pasemi/ and
make the necessary Kconfig and Makefile changes.

CC: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Olof Johansson <olof@lixom.net>

dev->real_num_tx_queues is correctly set already in alloc_netdev_mqs.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If bonding device is created via rtnl, it is created with default number
of rx/tx queues. This patch implements callback in bonding so the
correct value (previously specified by bonding module param) is used.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change details:
 - Removec bfi_ll.h bna_hw.h bna_ctrl.c and bna_txrx.c due to ENET, MSGQ
   and TXRX changes for new FW Driver interface and TX RX re-design.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove unused code.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change details:
This patch contains additional structure and function definition changes
that are required to enable the new msgq/enet/txrx redesign introduced
by the previous 4 patches.
 - structure and function definition changes to header files as a result
   of Ethport, Enet, IOCEth, Tx, Rx redesign.
 - ethtool changes to use new enet function and definitions
 - Set number of Tx and Rx queues bassed on underlying hardware. Define
   separate macros for maximum and supported numbers of Tx and Rx queues
   based on underlying hardware. Take VLAN header into account for MTU
   calculation. Default to INTx mode when pci_enable_msix() fails. Set a
   bit in Rx poll routine, check and wait for that bit to be cleared in
   the cleanup routine before proceeding.
 - The TX and Rx coalesce settings are programmed in steps of 5 us. The value
   that are not divisible by 5 are rounded to the next lower number. This was
   causing the value os 1 to 4 to be rounded to 0, which is an invalid setting.
   When creating Rx and Tx object, we are currently assigning the default
   values of Rx and Tx coalescing_timeo. If these values are changed in the
   driver to a different value, the change is lost during such operations as
   MTU change. In order to avoid that, pass the configured value of
   coalescing_timeo before Rx and Tx object creation. Fix
   bnad_tx_coalescing_timeo_set() so it applies to all the Tx objects.
 - Reorg uninitialization path in case of pci_probe failure.
 - Hardware clock setup changes to pass asic generation, port modes and
   asic mode as part firmware boot parameters to firmware.
 - FW mailbox interface changes to defined asic specific mailbox interfaces.
   h/w mailbox interfaces take 8-bit FIDs and 2-bit port id for owner. Cleaned
   up mailbox definitions and usage for new and old HW. Eliminated usage of
   ASIC ID. MSI-X vector assignment and programming done by firmware. Fixed
   host offsets for CPE/RME queue registers.
 - Implement polling mechanism for FW ready to have poll mechanism replaces
   the current interrupt based FW READY method. The timer based poll routine
   in IOC will query the ioc_fwstate register to see if there is a state
   change in FW, and sends the READY event. Removed infrastructure needed to
   support mbox READY event from fw as well as IOC code.
 - Move FW init to HW init. Handle the case where PCI mapping goes away when
   IOCPF state machine is waiting for semaphore.
 - Add IOC mbox call back to client indicating that the command is sent.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change details:
 - Add new file bna_hw_defs.h to support new code MSGQ, ENET and TX RX redign.
   This makes bna_hw.h obsolete and is removed in a later patch. bna_hw_defs.h
   removes all unused HW register definition that were part of bna_hw.h.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change details:
 - This patch contains the changes as a result of redesigning of Tx, Rx data
   path setup. In the old design, setting up Txqs, Rxqs were done in the driver.
   With the new design, most of the hardware setup steps for the Txq, Rxqs are
   moved to FW. Host driver issues commands to FW through the message queue to
   setup/teardown tx, rx data path. FW performs necessary steps and responds
   back to the driver with a status.
 - As a result of this redesign, the state machine implementation for Tx, Rx
   objects have changed significantly. Instead of doing the raw register access,
   these state machines mostly send a command to FW and wait for response and
   take the next action. In addition to tx, rx datapath setup, this patch also
   deals with rx filter configuration - such as unicast address, multicast
   address, vlan filter, promiscuous mode etc.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change details:
 - This patch contains the messages, opcodes and structure format for the
   messages and responses exchanged between driver and the FW. In addition
   this patch contains the state machine implementation for Ethport, Enet,
   IOCEth.
 - Ethport object is responsible for receiving link state events, sending
   port enable/disable commands to FW.
 - Enet object is responsible for synchronizing initialization/teardown of
   tx & rx datapath configuration.
 - IOCEth object is responsible for init/un-init of IO Controller in the
   adapter which runs the FW.
 - This patch also contains code for initialization and resource assignment
   for Ethport, Enet, IOCEth, Tx, Rx objects.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change details:
 - Currently modules communicate with the FW using 32 byte command and
   response register. This limits the size of the command and response
   messages exchanged with the FW to 32 bytes. We need a mechanism to
   exchange the comamnds and responses exchange with FW that exceeds 32 bytes.

 - MSGQ implementation provides that facility. It removes the assumption that
   command/response queue size is precisely calculated to accommodate all
   concurrent FW commands/responses. The queue depth is made variable now, defined
   by a macro. A waiting command list is implemented to hold all the commands
   when there is no place in the command queue. Callback is implemented for
   each command entry to invoke the module posting the command, when there is
   space in the command queue and the command was finally posted to the queue.
   Module/Object information is embedded in the response for tracking purpose.
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the Cisco driver into drivers/net/ethernet/cisco/ and make the
necessary Kconfig and Makefile changes.

CC: Christian Benvenuti <benve@cisco.com>
CC: Vasanthy Kolluri <vkolluri@cisco.com>
CC: Roopa Prabhu <roprabhu@cisco.com>
CC: David Wang <dwang2@cisco.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the IBM drivers into drivers/net/ethernet/ibm/ and make the
necessary Kconfig and Makefile changes.

- Renamed ibm_new_emac to emac
- Cleaned up Makefile and Kconfig options which referred to
  IBM_NEW_EMAC to IBM_EMAC
- ibmlana driver is a National Semiconductor SONIC driver so
  it was not moved

CC: Christoph Raisch <raisch@de.ibm.com>
CC: Santiago Leon <santil@linux.vnet.ibm.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: David Gibson <dwg@au1.ibm.com>
CC: Kyle Lucke <klucke@us.ibm.com>
CC: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move the Exar drivers into drivers/net/ethernet/neterion/ and make the
necessary Kconfig and Makefile changes.

CC: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>