- 11 Dec, 2019 20 commits
-
-
Russell King authored
Knowing whether we need to delay the MAC configuration because a module may have a PHY is useful to phylink to allow NBASE-T modules to work on systems supporting no more than 2.5G speeds. This commit allows us to delay such configuration until after the PHY has been probed by recording the parsed capabilities, and if the module may have a PHY, doing no more until the module_start() notification is called. At that point, we either have a PHY, or we don't. We move the PHY-based setup a little later, and use the PHYs support capabilities rather than the EEPROM parsed capabilities to determine whether we can support the PHY. Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Russell King authored
Split out the configuration step from phylink_sfp_module_insert() so we can re-use this later. Reviewed-by:
-
Russell King authored
Split link_an_mode between the configured setting and the current operating setting. This is an important distinction to make when we need to configure PHY mode for a plugged SFP+ module that does not use in-band signalling. Reviewed-by:
-
Russell King authored
Some SFP+ modules have Clause 45 PHYs embedded on them, which need a little more handling in order to ensure that they are correctly setup, as they switch the PHY link mode according to the negotiated speed. With Clause 22 PHYs, we assumed that they would operate in SGMII mode, but this assumption is now false. Adapt phylink to support Clause 45 PHYs on SFP+ modules. Reviewed-by:
-
Russell King authored
In order to support Clause 45 PHYs on SFP+ modules, which have an indeterminant phy interface mode, we need to be able to call phylink_bringup_phy() with a different interface mode to that used when binding the PHY. Reduce __phylink_connect_phy() to an attach operation, and move the call to phylink_bringup_phy() to its call sites. Reviewed-by:
-
Russell King authored
Some SFP+ modules have PHYs on them just like SFP modules do, except they are Clause 45 PHYs. The I2C protocol used to access them is modified slightly in order to send the device address and 16-bit register index. Reviewed-by:
-
Russell King authored
Move phy_start() and phy_stop() into the module_start and module_stop notifications in phylink, rather than having them in the SFP code. This gives phylink responsibility for controlling the PHY, rather than having SFP start and stop the PHY state machine. Reviewed-by:
-
Russell King authored
When dealing with some copper modules, we can't positively know the module capabilities are until we have probed the PHY. Without the full capabilities, we may end up failing a module that we could otherwise drive with a restricted set of capabilities. An example of this would be a module with a NBASE-T PHY plugged into a host that supports phy interface modes 2500BASE-X and SGMII. The PHY supports 10GBASE-R, 5000BASE-X, 2500BASE-X, SGMII interface modes, which means a subset of the capabilities are compatible with the host. However, reading the module EEPROM leads us to believe that the module only supports ethtool link mode 10GBASE-T, which is incompatible with the host - and thus results in the module being rejected. This patch adds an extra notification which are triggered after the SFP module's PHY probe, and a corresponding notification just before the PHY is removed. Reviewed-by:
-
Russell King authored
SFF-8024 is used to define various constants re-used in several SFF SFP-related specifications. Split these constants from the enum, and rename them to indicate that they're defined by SFF-8024. Add and use updated SFF-8024 extended compliance code definitions for 10GBASE-T, 5GBASE-T and 2.5GBASE-T modules. Reviewed-by:
-
Russell King authored
We don't need the EEPROM ID to derive the phy interface mode as we can derive it merely from the ethtool link modes. Remove the EEPROM ID argument to sfp_select_interface(). Reviewed-by:
-
Russell King authored
The 100BASE-FX and 100BASE-LX support assumes a PHY is present; this is probably an incorrect assumption. In any case, sfp_parse_support() will fail such a module. Let's stop pretending we support these modules. Reviewed-by:
-
Shahjada Abul Husain authored
T6 has a separate region known as high priority filter region that allows classifying packets going through ULD path. So, query firmware for HPFILTER resources and enable the high priority offload filter support when it is available. Signed-off-by:
Shahjada Abul Husain <shahjada@chelsio.com> Signed-off-by:
-
Chen Wandun authored
Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/ethernet/freescale/enetc/enetc_qos.c: In function enetc_setup_tc_cbs: drivers/net/ethernet/freescale/enetc/enetc_qos.c:195:6: warning: variable tc_max_sized_frame set but not used [-Wunused-but-set-variable] Fixes: c431047c ("enetc: add support Credit Based Shaper(CBS) for hardware offload") Signed-off-by:
Chen Wandun <chenwandun@huawei.com> Signed-off-by:
-
Jakub Kicinski authored
Device stats are currently hard coded in the PCI BAR0 layout. Add a ability to read them from the TLV area instead. Names for the stats are maintained by the driver, and their meaning documented. This allows us to more easily add and remove device stats. Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by:
-
Kuniyuki Iwashima authored
When a TCP socket is created, sk->sk_state is initialized twice as TCP_CLOSE in sock_init_data() and tcp_init_sock(). The tcp_init_sock() is always called after the sock_init_data(), so it is not necessary to update sk->sk_state in the tcp_init_sock(). Before v2.1.8, the code of the two functions was in the inet_create(). In the patch of v2.1.8, the tcp_v4/v6_init_sock() were added and the code of initialization of sk->state was duplicated. Signed-off-by:
Kuniyuki Iwashima <kuni1840@gmail.com> Signed-off-by:
-
Michael Walle authored
Provide a software TX timestamp and add it to the ethtool query interface. skb_tx_timestamp() is also needed if one would like to use PHY timestamping. Signed-off-by:
Michael Walle <michael@walle.cc> Signed-off-by:
-
David S. Miller authored
Jon Maloy says: ==================== tipc: introduce variable window congestion control We improve thoughput greatly by introducing a variety of the Reno congestion control algorithm at the link level. ==================== Signed-off-by: -
Jon Maloy authored
We introduce a simple variable window congestion control for links. The algorithm is inspired by the Reno algorithm, covering both 'slow start', 'congestion avoidance', and 'fast recovery' modes. - We introduce hard lower and upper window limits per link, still different and configurable per bearer type. - We introduce a 'slow start theshold' variable, initially set to the maximum window size. - We let a link start at the minimum congestion window, i.e. in slow start mode, and then let is grow rapidly (+1 per rceived ACK) until it reaches the slow start threshold and enters congestion avoidance mode. - In congestion avoidance mode we increment the congestion window for each window-size number of acked packets, up to a possible maximum equal to the configured maximum window. - For each non-duplicate NACK received, we drop back to fast recovery mode, by setting the both the slow start threshold to and the congestion window to (current_congestion_window / 2). - If the timeout handler finds that the transmit queue has not moved since the previous timeout, it drops the link back to slow start and forces a probe containing the last sent sequence number to the sent to the peer, so that this can discover the stale situation. This change does in reality have effect only on unicast ethernet transport, as we have seen that there is no room whatsoever for increasing the window max size for the UDP bearer. For now, we also choose to keep the limits for the broadcast link unchanged and equal. This algorithm seems to give a 50-100% throughput improvement for messages larger than MTU. Suggested-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Ying Xue <ying.xue@windriver.com> Signed-off-by:
Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
-
Jon Maloy authored
When we increase the link tranmsit window we often observe the following scenario: 1) A STATE message bypasses a sequence of traffic packets and arrives far ahead of those to the receiver. STATE messages contain a 'peers_nxt_snt' field to indicate which was the last packet sent from the peer. This mechanism is intended as a last resort for the receiver to detect missing packets, e.g., during very low traffic when there is no packet flow to help early loss detection. 3) The receiving link compares the 'peer_nxt_snt' field to its own 'rcv_nxt', finds that there is a gap, and immediately sends a NACK message back to the peer. 4) When this NACKs arrives at the sender, all the requested retransmissions are performed, since it is a first-time request. Just like in the scenario described in the previous commit this leads to many redundant retransmissions, with decreased throughput as a consequence. We fix this by adding two more conditions before we send a NACK in this sitution. First, the deferred queue must be empty, so we cannot assume that the potential packet loss has already been detected by other means. Second, we check the 'peers_snd_nxt' field only in probe/ probe_reply messages, thus turning this into a true mechanism of last resort as it was really meant to be. Acked-by:
-
Jon Maloy authored
When we increase the link send window we sometimes observe the following scenario: 1) A packet #N arrives out of order far ahead of a sequence of older packets which are still under way. The packet is added to the deferred queue. 2) The missing packets arrive in sequence, and for each 16th of them an ACK is sent back to the receiver, as it should be. 3) When building those ACK messages, it is checked if there is a gap between the link's 'rcv_nxt' and the first packet in the deferred queue. This is always the case until packet number #N-1 arrives, and a 'gap' indicator is added, effectively turning them into NACK messages. 4) When those NACKs arrive at the sender, all the requested retransmissions are done, since it is a first-time request. This sometimes leads to a huge amount of redundant retransmissions, causing a drop in max throughput. This problem gets worse when we in a later commit introduce variable window congestion control, since it drops the link back to 'fast recovery' much more often than necessary. We now fix this by not sending any 'gap' indicator in regular ACK messages. We already have a mechanism for sending explicit NACKs in place, and this is sufficient to keep up the packet flow. Acked-by:
-
- 10 Dec, 2019 8 commits
-
-
Nathan Chancellor authored
Clang warns: ../drivers/net/ppp/ppp_async.c:877:6: warning: misleading indentation; statement is not part of the previous 'if' [-Wmisleading-indentation] ap->rpkt = skb; ^ ../drivers/net/ppp/ppp_async.c:875:5: note: previous statement is here if (!skb) ^ 1 warning generated. This warning occurs because there is a space before the tab on this line. Clean up this entire block's indentation so that it is consistent with the Linux kernel coding style and clang no longer warns. Fixes: 6722e78c ("[PPP]: handle misaligned accesses") Link: https://github.com/ClangBuiltLinux/linux/issues/800Signed-off-by:Nathan Chancellor <natechancellor@gmail.com> Signed-off-by:
-
Nathan Chancellor authored
Clang warns: ../drivers/net/ethernet/smsc/smc911x.c:939:3: warning: misleading indentation; statement is not part of the previous 'if' [-Wmisleading-indentation] if (!lp->ctl_rfduplx) ^ ../drivers/net/ethernet/smsc/smc911x.c:936:2: note: previous statement is here if (lp->ctl_rspeed != 100) ^ 1 warning generated. This warning occurs because there is a space after the tab on this line. Remove it so that the indentation is consistent with the Linux kernel coding style and clang no longer warns. Fixes: 0a0c72c9 ("[PATCH] RE: [PATCH 1/1] net driver: Add support for SMSC LAN911x line of ethernet chips") Link: https://github.com/ClangBuiltLinux/linux/issues/796Signed-off-by: -
Nathan Chancellor authored
Clang warns: ../drivers/net/ethernet/dec/tulip/uli526x.c:1812:3: warning: misleading indentation; statement is not part of the previous 'if' [-Wmisleading-indentation] switch (mode) { ^ ../drivers/net/ethernet/dec/tulip/uli526x.c:1809:2: note: previous statement is here if (cr6set) ^ 1 warning generated. ../drivers/net/ethernet/dec/tulip/dmfe.c:2217:3: warning: misleading indentation; statement is not part of the previous 'if' [-Wmisleading-indentation] switch(mode) { ^ ../drivers/net/ethernet/dec/tulip/dmfe.c:2214:2: note: previous statement is here if (cr6set) ^ 1 warning generated. This warning occurs because there is a space before the tab on these lines. Remove them so that the indentation is consistent with the Linux kernel coding style and clang no longer warns. While we are here, adjust the default block in dmfe_init_module to have a proper break between the label and assignment and add a space between the switch and opening parentheses to avoid a checkpatch warning. Fixes: e1c3e501 ("[PATCH] initialisation cleanup for ULI526x-net-driver") Link: https://github.com/ClangBuiltLinux/linux/issues/795Signed-off-by: -
David S. Miller authored
Dan Murphy says: ==================== Fix Tx/Rx FIFO depth for DP83867 The DP83867 supports both the RGMII and SGMII modes. The Tx and Rx FIFO depths are configurable in these modes but may not applicable for both modes. When the device is configured for RGMII mode the Tx FIFO depth is applicable and for SGMII mode both Tx and Rx FIFO depth settings are applicable. When the driver was originally written only the RGMII device was available and there were no standard fifo-depth DT properties. The patchset converts the special ti,fifo-depth property to the standard tx-fifo-depth property while still allowing the ti,fifo-depth property to be set as to maintain backward compatibility. In addition to this change the rx-fifo-depth property support was added and only written when the device is configured for SGMII mode. ==================== Signed-off-by: -
Dan Murphy authored
This code changes the TI specific ti,fifo-depth to the common tx-fifo-depth property. The tx depth is applicable for both RGMII and SGMII modes of operation. rx-fifo-depth was added as well but this is only applicable for SGMII mode. So in summary if RGMII mode write tx fifo depth only if SGMII mode write both rx and tx fifo depths If the property is not populated in the device tree then set the value to the default values. Signed-off-by:
Dan Murphy <dmurphy@ti.com> Reported-by:
Adrian Bunk <bunk@kernel.org> Signed-off-by:
-
Dan Murphy authored
Convert the ti,fifo-depth from a TI specific property to the common tx-fifo-depth property. Also add support for the rx-fifo-depth. These are optional properties for this device and if these are not available then the fifo depths are set to device default values. Signed-off-by:
-
Kevin(Yudong) Yang authored
This patch introduces a sysctl knob "net.ipv4.tcp_no_ssthresh_metrics_save" that disables TCP ssthresh metrics cache by default. Other parts of TCP metrics cache, e.g. rtt, cwnd, remain unchanged. As modern networks becoming more and more dynamic, TCP metrics cache today often causes more harm than benefits. For example, the same IP address is often shared by different subscribers behind NAT in residential networks. Even if the IP address is not shared by different users, caching the slow-start threshold of a previous short flow using loss-based congestion control (e.g. cubic) often causes the future longer flows of the same network path to exit slow-start prematurely with abysmal throughput. Caching ssthresh is very risky and can lead to terrible performance. Therefore it makes sense to make disabling ssthresh caching by default and opt-in for specific networks by the administrators. This practice also has worked well for several years of deployment with CUBIC congestion control at Google. Acked-by:
Eric Dumazet <edumazet@google.com> Acked-by:
Neal Cardwell <ncardwell@google.com> Acked-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
Kevin(Yudong) Yang <yyd@google.com> Signed-off-by:
-
Xin Long authored
Commit 31243461 ("sctp: cache netns in sctp_ep_common") set netns in asoc and ep base since they're created, and it will never change. It's a better way to get netns from asoc and ep base, comparing to calling sock_net(). This patch is to replace them. v1->v2: - no change. Suggested-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
Neil Horman <nhorman@tuxdriver.com> Acked-by:
-
- 09 Dec, 2019 5 commits
-
-
Russell King authored
The Nokia GPON module can hold tx-fault active while it is initialising which can take up to 60s. Avoid this causing the module to be declared faulty after the SFP MSA defined non-cooled module timeout. Signed-off-by:
-
Colin Ian King authored
The variable rc is assigned with a value that is never read and it is re-assigned a new value later on. The assignment is redundant and can be removed. Clean up multiple occurrances of this pattern. Addresses-Coverity: ("Unused value") Signed-off-by:Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Mao Wenan authored
Convert cpu_to_le16(le16_to_cpu(frame->datalen) + len) to use le16_add_cpu(), which is more concise and does the same thing. Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Mao Wenan <maowenan@huawei.com> Signed-off-by:
-
David S. Miller authored
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next Johan Hedberg says: ==================== pull request: bluetooth-next 2019-12-09 Here's the first bluetooth-next pull request for 5.6: - Devicetree bindings updates for Broadcom controllers - Add support for PCM configuration for Broadcom controllers - btusb: Fixes for Realtek devices - butsb: A few other smaller fixes (mem leak & non-atomic allocation issue) Please let me know if there are any issues pulling. Thanks. ==================== Signed-off-by:
-
Jason A. Donenfeld authored
WireGuard is a layer 3 secure networking tunnel made specifically for the kernel, that aims to be much simpler and easier to audit than IPsec. Extensive documentation and description of the protocol and considerations, along with formal proofs of the cryptography, are available at: * https://www.wireguard.com/ * https://www.wireguard.com/papers/wireguard.pdf This commit implements WireGuard as a simple network device driver, accessible in the usual RTNL way used by virtual network drivers. It makes use of the udp_tunnel APIs, GRO, GSO, NAPI, and the usual set of networking subsystem APIs. It has a somewhat novel multicore queueing system designed for maximum throughput and minimal latency of encryption operations, but it is implemented modestly using workqueues and NAPI. Configuration is done via generic Netlink, and following a review from the Netlink maintainer a year ago, several high profile userspace tools have already implemented the API. This commit also comes with several different tests, both in-kernel tests and out-of-kernel tests based on network namespaces, taking profit of the fact that sockets used by WireGuard intentionally stay in the namespace the WireGuard interface was originally created, exactly like the semantics of userspace tun devices. See wireguard.com/netns/ for pictures and examples. The source code is fairly short, but rather than combining everything into a single file, WireGuard is developed as cleanly separable files, making auditing and comprehension easier. Things are laid out as follows: * noise.[ch], cookie.[ch], messages.h: These implement the bulk of the cryptographic aspects of the protocol, and are mostly data-only in nature, taking in buffers of bytes and spitting out buffers of bytes. They also handle reference counting for their various shared pieces of data, like keys and key lists. * ratelimiter.[ch]: Used as an integral part of cookie.[ch] for ratelimiting certain types of cryptographic operations in accordance with particular WireGuard semantics. * allowedips.[ch], peerlookup.[ch]: The main lookup structures of WireGuard, the former being trie-like with particular semantics, an integral part of the design of the protocol, and the latter just being nice helper functions around the various hashtables we use. * device.[ch]: Implementation of functions for the netdevice and for rtnl, responsible for maintaining the life of a given interface and wiring it up to the rest of WireGuard. * peer.[ch]: Each interface has a list of peers, with helper functions available here for creation, destruction, and reference counting. * socket.[ch]: Implementation of functions related to udp_socket and the general set of kernel socket APIs, for sending and receiving ciphertext UDP packets, and taking care of WireGuard-specific sticky socket routing semantics for the automatic roaming. * netlink.[ch]: Userspace API entry point for configuring WireGuard peers and devices. The API has been implemented by several userspace tools and network management utility, and the WireGuard project distributes the basic wg(8) tool. * queueing.[ch]: Shared function on the rx and tx path for handling the various queues used in the multicore algorithms. * send.c: Handles encrypting outgoing packets in parallel on multiple cores, before sending them in order on a single core, via workqueues and ring buffers. Also handles sending handshake and cookie messages as part of the protocol, in parallel. * receive.c: Handles decrypting incoming packets in parallel on multiple cores, before passing them off in order to be ingested via the rest of the networking subsystem with GRO via the typical NAPI poll function. Also handles receiving handshake and cookie messages as part of the protocol, in parallel. * timers.[ch]: Uses the timer wheel to implement protocol particular event timeouts, and gives a set of very simple event-driven entry point functions for callers. * main.c, version.h: Initialization and deinitialization of the module. * selftest/*.h: Runtime unit tests for some of the most security sensitive functions. * tools/testing/selftests/wireguard/netns.sh: Aforementioned testing script using network namespaces. This commit aims to be as self-contained as possible, implementing WireGuard as a standalone module not needing much special handling or coordination from the network subsystem. I expect for future optimizations to the network stack to positively improve WireGuard, and vice-versa, but for the time being, this exists as intentionally standalone. We introduce a menu option for CONFIG_WIREGUARD, as well as providing a verbose debug log and self-tests via CONFIG_WIREGUARD_DEBUG. Signed-off-by:
Jason A. Donenfeld <Jason@zx2c4.com> Cc: David Miller <davem@davemloft.net> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: linux-crypto@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by:
-
- 08 Dec, 2019 7 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) More jumbo frame fixes in r8169, from Heiner Kallweit. 2) Fix bpf build in minimal configuration, from Alexei Starovoitov. 3) Use after free in slcan driver, from Jouni Hogander. 4) Flower classifier port ranges don't work properly in the HW offload case, from Yoshiki Komachi. 5) Use after free in hns3_nic_maybe_stop_tx(), from Yunsheng Lin. 6) Out of bounds access in mqprio_dump(), from Vladyslav Tarasiuk. 7) Fix flow dissection in dsa TX path, from Alexander Lobakin. 8) Stale syncookie timestampe fixes from Guillaume Nault. [ Did an evil merge to silence a warning introduced by this pull - Linus ] * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits) r8169: fix rtl_hw_jumbo_disable for RTL8168evl net_sched: validate TCA_KIND attribute in tc_chain_tmplt_add() r8169: add missing RX enabling for WoL on RTL8125 vhost/vsock: accept only packets with the right dst_cid net: phy: dp83867: fix hfs boot in rgmii mode net: ethernet: ti: cpsw: fix extra rx interrupt inet: protect against too small mtu values. gre: refetch erspan header from skb->data after pskb_may_pull() pppoe: remove redundant BUG_ON() check in pppoe_pernet tcp: Protect accesses to .ts_recent_stamp with {READ,WRITE}_ONCE() tcp: tighten acceptance of ACKs not matching a child socket tcp: fix rejected syncookies due to stale timestamps lpc_eth: kernel BUG on remove tcp: md5: fix potential overestimation of TCP option space net: sched: allow indirect blocks to bind to clsact in TC net: core: rename indirect block ingress cb function net-sysfs: Call dev_hold always in netdev_queue_add_kobject net: dsa: fix flow dissection on Tx path net/tls: Fix return values to avoid ENOTSUPP net: avoid an indirect call in ____sys_recvmsg() ... -
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds authored
Pull more SCSI updates from James Bottomley: "Eleven patches, all in drivers (no core changes) that are either minor cleanups or small fixes. They were late arriving, but still safe for -rc1" * tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: MAINTAINERS: Add the linux-scsi mailing list to the ISCSI entry scsi: megaraid_sas: Make poll_aen_lock static scsi: sd_zbc: Improve report zones error printout scsi: qla2xxx: Fix qla2x00_request_irqs() for MSI scsi: qla2xxx: unregister ports after GPN_FT failure scsi: qla2xxx: fix rports not being mark as lost in sync fabric scan scsi: pm80xx: Remove unused include of linux/version.h scsi: pm80xx: fix logic to break out of loop when register value is 2 or 3 scsi: scsi_transport_sas: Fix memory leak when removing devices scsi: lpfc: size cpu map by last cpu id set scsi: ibmvscsi_tgt: Remove unneeded variable rc
-
git://git.samba.org/sfrench/cifs-2.6Linus Torvalds authored
Pull cifs fixes from Steve French: "Nine cifs/smb3 fixes: - one fix for stable (oops during oplock break) - two timestamp fixes including important one for updating mtime at close to avoid stale metadata caching issue on dirty files (also improves perf by using SMB2_CLOSE_FLAG_POSTQUERY_ATTRIB over the wire) - two fixes for "modefromsid" mount option for file create (now allows mode bits to be set more atomically and accurately on create by adding "sd_context" on create when modefromsid specified on mount) - two fixes for multichannel found in testing this week against different servers - two small cleanup patches" * tag '5.5-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6: smb3: improve check for when we send the security descriptor context on create smb3: fix mode passed in on create for modetosid mount option cifs: fix possible uninitialized access and race on iface_list cifs: Fix lookup of SMB connections on multichannel smb3: query attributes on file close smb3: remove unused flag passed into close functions cifs: remove redundant assignment to pointer pneg_ctxt fs: cifs: Fix atime update check vs mtime CIFS: Fix NULL-pointer dereference in smb2_push_mandatory_locks -
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull misc vfs cleanups from Al Viro: "No common topic, just three cleanups". * 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: make __d_alloc() static fs/namespace: add __user to open_tree and move_mount syscalls fs/fnctl: fix missing __user in fcntl_rw_hint()
-
git://github.com/jonmason/ntbLinus Torvalds authored
Pull NTB update from Jon Mason: "Just a simple patch to add a new Hygon Device ID to the AMD NTB device driver" * tag 'ntb-5.5' of git://github.com/jonmason/ntb: NTB: Add Hygon Device ID
-
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/inputLinus Torvalds authored
Pull more input updates from Dmitry Torokhov: - fixups for Synaptics RMI4 driver - a quirk for Goodinx touchscreen on Teclast tablet - a new keycode definition for activating privacy screen feature found on a few "enterprise" laptops - updates to snvs_pwrkey driver - polling uinput device for writing (which is always allowed) now works * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: synaptics-rmi4 - don't increment rmiaddr for SMBus transfers Input: synaptics-rmi4 - re-enable IRQs in f34v7_do_reflash Input: goodix - add upside-down quirk for Teclast X89 tablet Input: add privacy screen toggle keycode Input: uinput - fix returning EPOLLOUT from uinput_poll Input: snvs_pwrkey - remove gratuitous NULL initializers Input: snvs_pwrkey - send key events for i.MX6 S, DL and Q
-
