Pull networking fixes from David Miller:
 "I know this is a bit more than you want to see, and I've told the
  wireless folks under no uncertain terms that they must severely scale
  back the extent of the fixes they are submitting this late in the
  game.

  Anyways:

   1) vmxnet3's netpoll doesn't perform the equivalent of an ISR, which
      is the correct implementation, like it should.  Instead it does
      something like a NAPI poll operation.  This leads to crashes.

      From Neil Horman and Arnd Bergmann.

   2) Segmentation of SKBs requires proper socket orphaning of the
      fragments, otherwise we might access stale state released by the
      release callbacks.

      This is a 5 patch fix, but the initial patches are giving
      variables and such significantly clearer names such that the
      actual fix itself at the end looks trivial.

      From Michael S.  Tsirkin.

   3) TCP control block release can deadlock if invoked from a timer on
      an already "owned" socket.  Fix from Eric Dumazet.

   4) In the bridge multicast code, we must validate that the
      destination address of general queries is the link local all-nodes
      multicast address.  From Linus Lüssing.

   5) The x86 BPF JIT support for negative offsets puts the parameter
      for the helper function call in the wrong register.  Fix from
      Alexei Starovoitov.

   6) The descriptor type used for RTL_GIGA_MAC_VER_17 chips in the
      r8169 driver is incorrect.  Fix from Hayes Wang.

   7) The xen-netback driver tests skb_shinfo(skb)->gso_type bits to see
      if a packet is a GSO frame, but that's not the correct test.  It
      should use skb_is_gso(skb) instead.  Fix from Wei Liu.

   8) Negative msg->msg_namelen values should generate an error, from
      Matthew Leach.

   9) at86rf230 can deadlock because it takes the same lock from it's
      ISR and it's hard_start_xmit method, without disabling interrupts
      in the latter.  Fix from Alexander Aring.

  10) The FEC driver's restart doesn't perform operations in the correct
      order, so promiscuous settings can get lost.  Fix from Stefan
      Wahren.

  11) Fix SKB leak in SCTP cookie handling, from Daniel Borkmann.

  12) Reference count and memory leak fixes in TIPC from Ying Xue and
      Erik Hugne.

  13) Forced eviction in inet_frag_evictor() must strictly make sure all
      frags are deleted, otherwise module unload (f.e.  6lowpan) can
      crash.  Fix from Florian Westphal.

  14) Remove assumptions in AF_UNIX's use of csum_partial() (which it
      uses as a hash function), which breaks on PowerPC.  From Anton
      Blanchard.

      The main gist of the issue is that csum_partial() is defined only
      as a value that, once folded (f.e.  via csum_fold()) produces a
      correct 16-bit checksum.  It is legitimate, therefore, for
      csum_partial() to produce two different 32-bit values over the
      same data if their respective alignments are different.

  15) Fix endiannes bug in MAC address handling of ibmveth driver, also
      from Anton Blanchard.

  16) Error checks for ipv6 exthdrs offload registration are reversed,
      from Anton Nayshtut.

  17) Externally triggered ipv6 addrconf routes should count against the
      garbage collection threshold.  Fix from Sabrina Dubroca.

  18) The PCI shutdown handler added to the bnx2 driver can wedge the
      chip if it was not brought up earlier already, which in particular
      causes the firmware to shut down the PHY.  Fix from Michael Chan.

  19) Adjust the sanity WARN_ON_ONCE() in qdisc_list_add() because as
      currently coded it can and does trigger in legitimate situations.
      From Eric Dumazet.

  20) BNA driver fails to build on ARM because of a too large udelay()
      call, fix from Ben Hutchings.

  21) Fair-Queue qdisc holds locks during GFP_KERNEL allocations, fix
      from Eric Dumazet.

  22) The vlan passthrough ops added in the previous release causes a
      regression in source MAC address setting of outgoing headers in
      some circumstances.  Fix from Peter Boström"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (70 commits)
  ipv6: Avoid unnecessary temporary addresses being generated
  eth: fec: Fix lost promiscuous mode after reconnecting cable
  bonding: set correct vlan id for alb xmit path
  at86rf230: fix lockdep splats
  net/mlx4_en: Deregister multicast vxlan steering rules when going down
  vmxnet3: fix building without CONFIG_PCI_MSI
  MAINTAINERS: add networking selftests to NETWORKING
  net: socket: error on a negative msg_namelen
  MAINTAINERS: Add tools/net to NETWORKING [GENERAL]
  packet: doc: Spelling s/than/that/
  net/mlx4_core: Load the IB driver when the device supports IBoE
  net/mlx4_en: Handle vxlan steering rules for mac address changes
  net/mlx4_core: Fix wrong dump of the vxlan offloads device capability
  xen-netback: use skb_is_gso in xenvif_start_xmit
  r8169: fix the incorrect tx descriptor version
  tools/net/Makefile: Define PACKAGE to fix build problems
  x86: bpf_jit: support negative offsets
  bridge: multicast: enable snooping on general queries only
  bridge: multicast: add sanity check for general query destination
  tcp: tcp_release_cb() should release socket ownership
  ...

tmp_prefered_lft is an offset to ifp->tstamp, not now. Therefore
age needs to be added to the condition.

Age calculation in ipv6_create_tempaddr is different from the one
in addrconf_verify and doesn't consider ADDRCONF_TIMER_FUZZ_MINUS.
This can cause age in ipv6_create_tempaddr to be less than the one
in addrconf_verify and therefore unnecessary temporary address to
be generated.
Use age calculation as in addrconf_modify to avoid this.
Signed-off-by: Heiner Kallweit <heiner.kallweit@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the Freescale fec is in promiscuous mode and network cable is
reconnected then the promiscuous mode get lost. The problem is caused
by a too soon call of set_multicast_list to re-enable promisc mode.
The FEC_R_CNTRL register changes are overwritten by fec_restart.

This patch fixes this by moving the call behind the init of FEC_R_CNTRL
register in fec_restart.

Successful tested on a i.MX28 board.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit d3ab3ffd
(bonding: use rlb_client_info->vlan_id instead of ->tag)
remove the rlb_client_info->tag, but occur some issues,
The vlan_get_tag() will return 0 for success and -EINVAL for
error, so the client_info->vlan_id always be set to 0 if the
vlan_get_tag return 0 for success, so the client_info would
never get a correct vlan id.

We should only set the vlan id to 0 when the vlan_get_tag return error.

Fixes: d3ab3ffd (bonding: use rlb_client_info->vlan_id instead of ->tag)

CC: Ding Tianhong <dingtianhong@huawei.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fix a lockdep in the at86rf230 driver, otherwise we get:

[   30.206517] =================================
[   30.211078] [ INFO: inconsistent lock state ]
[   30.215647] 3.14.0-20140108-1-00994-g32e9426 #163 Not tainted
[   30.221660] ---------------------------------
[   30.226222] inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W} usage.
[   30.232514] systemd-udevd/157 [HC1[1]:SC0[0]:HE0:SE1] takes:
[   30.238439]  (&(&lp->lock)->rlock){?.+...}, at: [<c03600f8>] at86rf230_isr+0x18/0x44
[   30.246621] {HARDIRQ-ON-W} state was registered at:
[   30.251728]   [<c0061ce4>] __lock_acquire+0x7a4/0x18d8
[   30.257135]   [<c0063500>] lock_acquire+0x68/0x7c
[   30.262071]   [<c0588820>] _raw_spin_lock+0x28/0x38
[   30.267203]   [<c0361240>] at86rf230_xmit+0x1c/0x144
[   30.272412]   [<c057ba6c>] mac802154_xmit_worker+0x88/0x148
[   30.278271]   [<c0047844>] process_one_work+0x274/0x404
[   30.283761]   [<c00484c0>] worker_thread+0x228/0x374
[   30.288971]   [<c004cfb8>] kthread+0xd0/0xe4
[   30.293455]   [<c000dac8>] ret_from_fork+0x14/0x2c
[   30.298493] irq event stamp: 8948
[   30.301963] hardirqs last  enabled at (8947): [<c00cb290>] __kmalloc+0xb4/0x110
[   30.309636] hardirqs last disabled at (8948): [<c00115d4>] __irq_svc+0x34/0x5c
[   30.317215] softirqs last  enabled at (8452): [<c0037324>] __do_softirq+0x1dc/0x264
[   30.325243] softirqs last disabled at (8439): [<c0037638>] irq_exit+0x80/0xf4

We use the lp->lock inside the isr of at86rf230, that's why we need the
irqsave spinlock calls.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When mlx4_en_stop_port() is called, we need to deregister also the
tunnel steering rules that relate to multicast.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit d25f06ea "vmxnet3: fix netpoll race condition",
the vmxnet3 driver fails to build when CONFIG_PCI_MSI is disabled,
because it unconditionally references the vmxnet3_msix_rx()
function.

To fix this, use the same #ifdef in the caller that exists around
the function definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: stable@vger.kernel.org
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add it to NETWORKING [GENERAL] to make sure patches for selftests
go to the netdev list as well.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull PCI fixes from Bjorn Helgaas:
 "These are two important regression fixes for bugs we've introduced so
  far in v3.14.

  One of the resource allocation changes from the merge window is broken
  for 32-bit kernels where we don't use _CRS for PCI host bridges
  (mostly pre-2008 machines), so there's a fix for that.

  The INTx enable change we put in after the merge window turned out to
  break pciehp because we re-enable INTx on the hotplug bridge, which
  apparently breaks MSI for future hotplug events"

* tag 'pci-v3.14-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Don't check resource_size() in pci_bus_alloc_resource()
  PCI: Enable INTx in pci_reenable_device() only when MSI/MSI-X not enabled

Pull KVM fixes from Paolo Bonzini:
 "The ARM patch fixes a build breakage with randconfig.  The x86 one
  fixes Windows guests on AMD processors"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: SVM: fix cr8 intercept window
  ARM: KVM: fix non-VGIC compilation

Pull sound fixes from Takashi Iwai:
 "A few fixes for ASoC (N810 DT init fix, DPCM error path fix and a
  couple of MFD init fixes), and a fix for a Lenovo laptop.  All small
  and trivial fixes, suitable for rc7"

* tag 'sound-3.14-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ASoC: 88pm860: Fix IO setup
  ASoC: si476x: Fix IO setup
  ALSA: hda - Fix loud click noise with IdeaPad 410Y
  ASoC: pcm: free path list before exiting from error conditions
  ASoC: n810: fix init with DT boot

When copying in a struct msghdr from the user, if the user has set the
msg_namelen parameter to a negative value it gets clamped to a valid
size due to a comparison between signed and unsigned values.

Ensure the syscall errors when the user passes in a negative value.
Signed-off-by: Matthew Leach <matthew.leach@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure patches for these tools go to the netdev list as well.

References: https://marc.info/?l=linux-kernel&m=139450284501328&w=2
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
mlx4 fixes

These short series fixes two bugs related to the vxlan support and a
missing req module call for the IB driver which is needed to support
IB/RDMA over Ethernet.

Pathes done over the net tree, commit dd38743b "vlan: Set correct
source MAC address with TX VLAN offload enabled"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When checking what protocol drivers to load, the IB driver should be
requested also over Ethernet ports, if the device supports IBoE (RoCE).

Fixes: b046ffe5 'net/mlx4_core: Load higher level modules according to ports type'
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the device mac address is changed, we must deregister the vxlan
steering rule associated with the previous mac, and register a new
steering rule using the new mac.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the value used to dump the vxlan offloads device capability to align
with the MLX4_DEV_CAP_FLAG2_yyy definition. While on that, add dump to
the IPoIB flow-steering device capability and fix small typo.

The vxlan cap value wasn't fully handled when a conflict was resolved
between MLX4_DEV_CAP_FLAG2_DMFS_IPOIB coming from the IB tree to
MLX4_DEV_CAP_FLAG2_VXLAN_OFFLOADS coming from net-next.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In 5bd07670 ("Xen-netback: Fix issue caused by using gso_type wrongly")
we use skb_is_gso to determine if we need an extra slot to accommodate
the SKB. There's similar error in interface.c. Change that to use
skb_is_gso as well.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: Annie Li <annie.li@oracle.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We always disable cr8 intercept in its handler, but only re-enable it
if handling KVM_REQ_EVENT, so there can be a window where we do not
intercept cr8 writes, which allows an interrupt to disrupt a higher
priority task.

Fix this by disabling intercepts in the same function that re-enables
them when needed. This fixes BSOD in Windows 2008.

Cc: <stable@vger.kernel.org>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Paul reported that after f75b99d5 ("PCI: Enforce bus address limits in
resource allocation") on a 32-bit kernel (CONFIG_PHYS_ADDR_T_64BIT not
set), intel-gtt complained "can't ioremap flush page - no chipset
flushing".  In addition, other PCI resource allocations, e.g., for bridge
windows, failed.

This happens because we incorrectly skip bus resources of
[mem 0x00000000-0xffffffff] because we think they are of size zero.
When resource_size_t is 32 bits wide, resource_size() on
[mem 0x00000000-0xffffffff] returns 0 because (r->end - r->start + 1)
overflows.

Therefore, we can't use "resource_size() == 0" to decide that allocation
from this resource will fail.  allocate_resource() should fail anyway if it
can't satisfy the address constraints, so we should just depend on that.

A [mem 0x00000000-0xffffffff] bus resource is obviously not really valid,
but we do fall back to it as a default when we don't have information about
host bridge apertures.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=71611
Fixes: f75b99d5 PCI: Enforce bus address limits in resource allocation
Reported-and-tested-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Andreas reported that after 1f42db78 ("PCI: Enable INTx if BIOS left
them disabled"), pciehp surprise removal stopped working.

This happens because pci_reenable_device() on the hotplug bridge (used in
the pciehp_configure_device() path) clears the Interrupt Disable bit, which
apparently breaks the bridge's MSI hotplug event reporting.

Previously we cleared the Interrupt Disable bit in do_pci_enable_device(),
which is used by both pci_enable_device() and pci_reenable_device().  But
we use pci_reenable_device() after the driver may have enabled MSI or
MSI-X, and we *set* Interrupt Disable as part of enabling MSI/MSI-X.

This patch clears Interrupt Disable only when MSI/MSI-X has not been
enabled.

Fixes: 1f42db78 PCI: Enable INTx if BIOS left them disabled
Link: https://bugzilla.kernel.org/show_bug.cgi?id=71691Reported-and-tested-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>

The tx descriptor version of RTL8111B belong to RTL_TD_0.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes the following build problem with binutils-2.24

gcc -Wall -O2   -c -o bpf_jit_disasm.o bpf_jit_disasm.c
In file included from bpf_jit_disasm.c:25:0:
/usr/include/bfd.h:35:2: error: #error config.h must be included
before this header
 #error config.h must be included before this header

This is similar to commit 3ce711a6
"perf tools: bfd.h/libbfd detection fails with recent binutils"

See: https://sourceware.org/bugzilla/show_bug.cgi?id=14243

CC: David S. Miller <davem@davemloft.net>
CC: Daniel Borkmann <dborkman@redhat.com>
CC: netdev@vger.kernel.org
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit a998d434 claimed to introduce negative offset support to x86 jit,
but it couldn't be working, since at the time of the execution
of LD+ABS or LD+IND instructions via call into
bpf_internal_load_pointer_neg_helper() the %edx (3rd argument of this func)
had junk value instead of access size in bytes (1 or 2 or 4).

Store size into %edx instead of %ecx (what original commit intended to do)

Fixes: a998d434 ("bpf jit: Let the x86 jit handle negative offsets")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Jan Seiffert <kaffeemonster@googlemail.com>
Cc: Eric Dumazet <edumazet@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Without this check someone could easily create a denial of service
by injecting multicast-specific queries to enable the bridge
snooping part if no real querier issuing periodic general queries
is present on the link which would result in the bridge wrongly
shutting down ports for multicast traffic as the bridge did not learn
about these listeners.

With this patch the snooping code is enabled upon receiving valid,
general queries only.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

General IGMP and MLD queries are supposed to have the multicast
link-local all-nodes address as their destination according to RFC2236
section 9, RFC3376 section 4.1.12/9.1, RFC2710 section 8 and RFC3810
section 5.1.15.

Without this check, such malformed IGMP/MLD queries can result in a
denial of service: The queries are ignored by most IGMP/MLD listeners
therefore they will not respond with an IGMP/MLD report. However,
without this patch these malformed MLD queries would enable the
snooping part in the bridge code, potentially shutting down the
according ports towards these hosts for multicast traffic as the
bridge did not learn about these listeners.
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Lars Persson reported following deadlock :

-000 |M:0x0:0x802B6AF8(asm) <-- arch_spin_lock
-001 |tcp_v4_rcv(skb = 0x8BD527A0) <-- sk = 0x8BE6B2A0
-002 |ip_local_deliver_finish(skb = 0x8BD527A0)
-003 |__netif_receive_skb_core(skb = 0x8BD527A0, ?)
-004 |netif_receive_skb(skb = 0x8BD527A0)
-005 |elk_poll(napi = 0x8C770500, budget = 64)
-006 |net_rx_action(?)
-007 |__do_softirq()
-008 |do_softirq()
-009 |local_bh_enable()
-010 |tcp_rcv_established(sk = 0x8BE6B2A0, skb = 0x87D3A9E0, th = 0x814EBE14, ?)
-011 |tcp_v4_do_rcv(sk = 0x8BE6B2A0, skb = 0x87D3A9E0)
-012 |tcp_delack_timer_handler(sk = 0x8BE6B2A0)
-013 |tcp_release_cb(sk = 0x8BE6B2A0)
-014 |release_sock(sk = 0x8BE6B2A0)
-015 |tcp_sendmsg(?, sk = 0x8BE6B2A0, ?, ?)
-016 |sock_sendmsg(sock = 0x8518C4C0, msg = 0x87D8DAA8, size = 4096)
-017 |kernel_sendmsg(?, ?, ?, ?, size = 4096)
-018 |smb_send_kvec()
-019 |smb_send_rqst(server = 0x87C4D400, rqst = 0x87D8DBA0)
-020 |cifs_call_async()
-021 |cifs_async_writev(wdata = 0x87FD6580)
-022 |cifs_writepages(mapping = 0x852096E4, wbc = 0x87D8DC88)
-023 |__writeback_single_inode(inode = 0x852095D0, wbc = 0x87D8DC88)
-024 |writeback_sb_inodes(sb = 0x87D6D800, wb = 0x87E4A9C0, work = 0x87D8DD88)
-025 |__writeback_inodes_wb(wb = 0x87E4A9C0, work = 0x87D8DD88)
-026 |wb_writeback(wb = 0x87E4A9C0, work = 0x87D8DD88)
-027 |wb_do_writeback(wb = 0x87E4A9C0, force_wait = 0)
-028 |bdi_writeback_workfn(work = 0x87E4A9CC)
-029 |process_one_work(worker = 0x8B045880, work = 0x87E4A9CC)
-030 |worker_thread(__worker = 0x8B045880)
-031 |kthread(_create = 0x87CADD90)
-032 |ret_from_kernel_thread(asm)

Bug occurs because __tcp_checksum_complete_user() enables BH, assuming
it is running from softirq context.

Lars trace involved a NIC without RX checksum support but other points
are problematic as well, like the prequeue stuff.

Problem is triggered by a timer, that found socket being owned by user.

tcp_release_cb() should call tcp_write_timer_handler() or
tcp_delack_timer_handler() in the appropriate context :

BH disabled and socket lock held, but 'owned' field cleared,
as if they were running from timer handlers.

Fixes: 6f458dfb ("tcp: improve latencies of timer triggered events")
Reported-by: Lars Persson <lars.persson@axis.com>
Tested-by: Lars Persson <lars.persson@axis.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael S. Tsirkin says:

====================
skbuff: fix skb_segment with zero copy skbs

This fixes a bug in skb_segment where it moves frags
between skbs without orphaning them.
This causes userspace to assume it's safe to
reuse the buffer, and receiver gets corrupted data.
This further might leak information from the
transmitter on the wire.

To fix track which skb does a copied frag belong
to, and orphan frags when copying them.

As we are tracking multiple skbs here, using
short names (skb,nskb,fskb,skb_frag,frag) becomes confusing.
So before adding another one, I refactor these names
slightly.

Patch is split out to make it easier to
verify that all trasformations are trivially correct.

The problem was observed in the field,
so I think that the patch is necessary on stable
as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>

skb_segment copies frags around, so we need
to copy them carefully to avoid accessing
user memory after reporting completion to userspace
through a callback.

skb_segment doesn't normally happen on datapath:
TSO needs to be disabled - so disabling zero copy
in this case does not look like a big deal.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

fskb is unrelated to frag: it's coming from
frag_list. Rename it list_skb to avoid confusion.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rename local variable to make it easier to tell at a glance that we are
dealing with a head skb.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb_frag can in fact point at either skb
or fskb so rename it generally "frag".
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

frag points at nskb, so name it appropriately
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Giuseppe Cavallaro says:

====================
stmmac fixes: EEE and chained mode

These patches are to fix some new problems in the STMMAC driver.

Mandatory changes are for EEE that needs to be disabled if not supported
and for the chain mode that is broken and the kernel panics if this mode
is enabled.

v3: removed a patch from my previous set that touched the stmmac_tx path
    that has not to be applied. Other patches for cleaning-up will be
    sent on top of net-next git repo.

v4: do not surround the defaul buffer selection using Koption and adopt
    a default to 1536bytes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This is to fix the compatibility to the STiD127 SoC.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to fix the chain mode that was broken
and generated a panic. This patch reviews the chain/ring
modes now shaing the same structure and taking care
about the pointers and callbacks.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to fix and tune the default buffer sizes.
It reduces the default bufsize used by the driver from
4KiB to 1536 bytes.

Patch has been tested on both ARM and SH4 platform based.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to disable the EEE (so HW and timers)
for example when the phy communicates that the EEE
can be supported anymore.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vmxnet3's netpoll driver is incorrectly coded.  It directly calls
vmxnet3_do_poll, which is the driver internal napi poll routine.  As the netpoll
controller method doesn't block real napi polls in any way, there is a potential
for race conditions in which the netpoll controller method and the napi poll
method run concurrently.  The result is data corruption causing panics such as this
one recently observed:
PID: 1371   TASK: ffff88023762caa0  CPU: 1   COMMAND: "rs:main Q:Reg"
 #0 [ffff88023abd5780] machine_kexec at ffffffff81038f3b
 #1 [ffff88023abd57e0] crash_kexec at ffffffff810c5d92
 #2 [ffff88023abd58b0] oops_end at ffffffff8152b570
 #3 [ffff88023abd58e0] die at ffffffff81010e0b
 #4 [ffff88023abd5910] do_trap at ffffffff8152add4
 #5 [ffff88023abd5970] do_invalid_op at ffffffff8100cf95
 #6 [ffff88023abd5a10] invalid_op at ffffffff8100bf9b
    [exception RIP: vmxnet3_rq_rx_complete+1968]
    RIP: ffffffffa00f1e80  RSP: ffff88023abd5ac8  RFLAGS: 00010086
    RAX: 0000000000000000  RBX: ffff88023b5dcee0  RCX: 00000000000000c0
    RDX: 0000000000000000  RSI: 00000000000005f2  RDI: ffff88023b5dcee0
    RBP: ffff88023abd5b48   R8: 0000000000000000   R9: ffff88023a3b6048
    R10: 0000000000000000  R11: 0000000000000002  R12: ffff8802398d4cd8
    R13: ffff88023af35140  R14: ffff88023b60c890  R15: 0000000000000000
    ORIG_RAX: ffffffffffffffff  CS: 0010  SS: 0018
 #7 [ffff88023abd5b50] vmxnet3_do_poll at ffffffffa00f204a [vmxnet3]
 #8 [ffff88023abd5b80] vmxnet3_netpoll at ffffffffa00f209c [vmxnet3]
 #9 [ffff88023abd5ba0] netpoll_poll_dev at ffffffff81472bb7

The fix is to do as other drivers do, and have the poll controller call the top
half interrupt handler, which schedules a napi poll properly to recieve frames

Tested by myself, successfully.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: stable@vger.kernel.org
Reviewed-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>