Introduce XDP support for XDP_TX verdict and ndo_xdp_xmit function
pointer.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Report xdp stats through ethtool
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce basic XDP support to mtk_eth_soc driver.
Supported XDP verdicts:
- XDP_PASS
- XDP_DROP
- XDP_REDIRECT
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rely on page_pool allocator for single page buffers in order to keep
them dma mapped and add skb recycling support.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
100GbE Intel Wired LAN Driver Updates 2022-07-21

This series contains updates to ice driver only.

Karol adds implementation for GNSS write; data is written to the GNSS
module through TTY device using u-blox UBX protocol.

* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
  ice: add write functionality for GNSS TTY
  ice: add i2c write command
====================

Link: https://lore.kernel.org/r/20220721202842.3276257-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The current code allows for VXLAN and GENEVE to inherit the TOS
respective the TTL when skb-protocol is ETH_P_IP or ETH_P_IPV6.
However when the payload is VLAN encapsulated, then this inheriting
does not work, because the visible skb-protocol is of type
ETH_P_8021Q or ETH_P_8021AD.

Instead of skb->protocol use skb_protocol().
Signed-off-by: Matthias May <matthias.may@westermo.com>
Link: https://lore.kernel.org/r/20220721202718.10092-1-matthias.may@westermo.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Justin Chen says:

====================
net: usb: ax88179_178a: improvements and bug fixes

Power management was partially broken. There were two issues when dropping
into a sleep state.
1. Resume was not doing a fully HW restore. Only a partial restore. This
lead to a couple things being broken on resume. One of them being tcp rx.
2. wolopt was not being restored properly on resume.

Also did some general improvements and clean up to make it easier to fix
the issues mentioned above.
====================

Link: https://lore.kernel.org/r/1658363296-15734-1-git-send-email-justinpopo6@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

- Check if wol is supported on reset instead of everytime get_wol
is called.
- Save wolopts in private data instead of relying on the HW to save it.
- Defer enabling WoL until suspend instead of enabling it everytime
set_wol is called.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

We need more space to save WoL context. So lets allocate memory
for ax88179_data instead of using struct usbnet data field which
only supports 5 words. We continue to use the struct usbnet data
field for multicast filters. However since we no longer have the
private data stored there, we can shift it to the beginning.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The hardware state was only partially restored, which meant certain
functionality was broken on resume. Do a full HW reset on resume to
fix this.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Instead of passing in_pm flags all over the place, use the private
struct to handle in_pm mode.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Bind and reset are basically doing the same thing. Remove the duplicate
code and have bind call into reset.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'for-net-next-2022-07-22' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Luiz Augusto von Dentz says:

====================
bluetooth-next pull request for net-next:

 - Add support for IM Networks PID 0x3568
 - Add support for BCM4349B1
 - Add support for CYW55572
 - Add support for MT7922 VID/PID 0489/e0e2
 - Add support for Realtek RTL8852C
 - Initial support for Isochronous Channels/ISO sockets
 - Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING quirk

* tag 'for-net-next-2022-07-22' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next: (58 commits)
  Bluetooth: btusb: Detect if an ACL packet is in fact an ISO packet
  Bluetooth: btusb: Add support for ISO packets
  Bluetooth: ISO: Add broadcast support
  Bluetooth: Add initial implementation of BIS connections
  Bluetooth: Add BTPROTO_ISO socket type
  Bluetooth: Add initial implementation of CIS connections
  Bluetooth: hci_core: Introduce hci_recv_event_data
  Bluetooth: Convert delayed discov_off to hci_sync
  Bluetooth: Remove update_scan hci_request dependancy
  Bluetooth: Remove dead code from hci_request.c
  Bluetooth: btrtl: Fix typo in comment
  Bluetooth: MGMT: Fix holding hci_conn reference while command is queued
  Bluetooth: mgmt: Fix using hci_conn_abort
  Bluetooth: Use bt_status to convert from errno
  Bluetooth: Add bt_status
  Bluetooth: hci_sync: Split hci_dev_open_sync
  Bluetooth: hci_sync: Refactor remove Adv Monitor
  Bluetooth: hci_sync: Refactor add Adv Monitor
  Bluetooth: hci_sync: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING
  Bluetooth: btusb: Remove HCI_QUIRK_BROKEN_ERR_DATA_REPORTING for fake CSR
  ...
====================

Link: https://lore.kernel.org/r/20220723002232.964796-1-luiz.dentz@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Fix up the packet type if ISO packets are sent over the bulk endpoint.

Note: This is a stopgap since the Bluetooth specification currently
doesn't define any endpoint to transport ISO packets.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This enabled btusb driver to properly transmit ISO packets.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This adds broadcast support for BTPROTO_ISO by extending the
sockaddr_iso with a new struct sockaddr_iso_bc where the socket user
can set the broadcast address when receiving, the SID and the BIS
indexes it wants to synchronize.

When using BTPROTO_ISO for broadcast the roles are:

Broadcaster -> uses connect with address set to BDADDR_ANY:
> tools/isotest -s 00:00:00:00:00:00

Broadcast Receiver -> uses listen with address set to broadcaster:
> tools/isotest -d 00:AA:01:00:00:00
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This adds initial support for BIS/BIG which includes:

== Broadcaster role: Setup a periodic advertising and create a BIG ==

> tools/isotest -s 00:00:00:00:00:00
isotest[63]: Connected [00:00:00:00:00:00]
isotest[63]: QoS BIG 0x00 BIS 0x00 Packing 0x00 Framing 0x00]
isotest[63]: Output QoS [Interval 10000 us Latency 10 ms SDU 40 PHY 0x02
RTN 2]
isotest[63]: Sending ...
isotest[63]: Number of packets: 1
isotest[63]: Socket jitter buffer: 80 buffer
< HCI Command: LE Set Perio.. (0x08|0x003e) plen 7
...
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Periodic Advertising Parameters (0x08|0x003e) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Perio.. (0x08|0x003f) plen 7
...
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Periodic Advertising Data (0x08|0x003f) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Perio.. (0x08|0x0040) plen 2
...
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Periodic Advertising Enable (0x08|0x0040) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Create B.. (0x08|0x0068) plen 31
...
> HCI Event: Command Status (0x0f) plen 4
      LE Create Broadcast Isochronous Group (0x08|0x0068) ncmd 1
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 21
      LE Broadcast Isochronous Group Complete (0x1b)
      ...

== Broadcast Receiver role: Create a PA Sync and BIG Sync ==

> tools/isotest -i hci1 -d 00:AA:01:00:00:00
isotest[66]: Waiting for connection 00:AA:01:00:00:00...
< HCI Command: LE Periodic Advert.. (0x08|0x0044) plen 14
...
> HCI Event: Command Status (0x0f) plen 4
      LE Periodic Advertising Create Sync (0x08|0x0044) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Extended Sca.. (0x08|0x0041) plen 8
...
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Extended Sca.. (0x08|0x0042) plen 6
...
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Scan Enable (0x08|0x0042) ncmd 1
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 29
      LE Extended Advertising Report (0x0d)
      ...
> HCI Event: LE Meta Event (0x3e) plen 16
      LE Periodic Advertising Sync Established (0x0e)
      ...
< HCI Command: LE Broadcast Isoch.. (0x08|0x006b) plen 25
...
> HCI Event: Command Status (0x0f) plen 4
      LE Broadcast Isochronous Group Create Sync (0x08|0x006b) ncmd 1
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 17
      LE Broadcast Isochronous Group Sync Estabilished (0x1d)
      ...
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This introduces a new socket type BTPROTO_ISO which can be enabled with
use of ISO Socket experiemental UUID, it can used to initiate/accept
connections and transfer packets between userspace and kernel similarly
to how BTPROTO_SCO works:

Central -> uses connect with address set to destination bdaddr:
> tools/isotest -s 00:AA:01:00:00:00

Peripheral -> uses listen:
> tools/isotest -d
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This adds the initial implementation of CIS connections and introduces
the ISO packets/links.

== Central: Set CIG Parameters, create a CIS and Setup Data Path ==

> tools/isotest -s <address>

< HCI Command: LE Extended Create... (0x08|0x0043) plen 26
...
> HCI Event: Command Status (0x0f) plen 4
      LE Extended Create Connection (0x08|0x0043) ncmd 1
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 31
      LE Enhanced Connection Complete (0x0a)
      ...
< HCI Command: LE Create Connected... (0x08|0x0064) plen 5
...
> HCI Event: Command Status (0x0f) plen 4
      LE Create Connected Isochronous Stream (0x08|0x0064) ncmd 1
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 29
      LE Connected Isochronous Stream Established (0x19)
      ...
< HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13
...
> HCI Event: Command Complete (0x0e) plen 6
      LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1
        Status: Success (0x00)
        Handle: 257
< HCI Command: LE Setup Isochronou.. (0x08|0x006e) plen 13
...
> HCI Event: Command Complete (0x0e) plen 6
      LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1
        Status: Success (0x00)
        Handle: 257

== Peripheral: Accept CIS and Setup Data Path ==

> tools/isotest -d

 HCI Event: LE Meta Event (0x3e) plen 7
      LE Connected Isochronous Stream Request (0x1a)
...
< HCI Command: LE Accept Co.. (0x08|0x0066) plen 2
...
> HCI Event: LE Meta Event (0x3e) plen 29
      LE Connected Isochronous Stream Established (0x19)
...
< HCI Command: LE Setup Is.. (0x08|0x006e) plen 13
...
> HCI Event: Command Complete (0x0e) plen 6
      LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1
        Status: Success (0x00)
        Handle: 257
< HCI Command: LE Setup Is.. (0x08|0x006e) plen 13
...
> HCI Event: Command Complete (0x0e) plen 6
      LE Setup Isochronous Data Path (0x08|0x006e) ncmd 1
        Status: Success (0x00)
        Handle: 257
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Daniel Borkmann says:

====================
bpf-next 2022-07-22

We've added 73 non-merge commits during the last 12 day(s) which contain
a total of 88 files changed, 3458 insertions(+), 860 deletions(-).

The main changes are:

1) Implement BPF trampoline for arm64 JIT, from Xu Kuohai.

2) Add ksyscall/kretsyscall section support to libbpf to simplify tracing kernel
   syscalls through kprobe mechanism, from Andrii Nakryiko.

3) Allow for livepatch (KLP) and BPF trampolines to attach to the same kernel
   function, from Song Liu & Jiri Olsa.

4) Add new kfunc infrastructure for netfilter's CT e.g. to insert and change
   entries, from Kumar Kartikeya Dwivedi & Lorenzo Bianconi.

5) Add a ksym BPF iterator to allow for more flexible and efficient interactions
   with kernel symbols, from Alan Maguire.

6) Bug fixes in libbpf e.g. for uprobe binary path resolution, from Dan Carpenter.

7) Fix BPF subprog function names in stack traces, from Alexei Starovoitov.

8) libbpf support for writing custom perf event readers, from Jon Doron.

9) Switch to use SPDX tag for BPF helper man page, from Alejandro Colomar.

10) Fix xsk send-only sockets when in busy poll mode, from Maciej Fijalkowski.

11) Reparent BPF maps and their charging on memcg offlining, from Roman Gushchin.

12) Multiple follow-up fixes around BPF lsm cgroup infra, from Stanislav Fomichev.

13) Use bootstrap version of bpftool where possible to speed up builds, from Pu Lehui.

14) Cleanup BPF verifier's check_func_arg() handling, from Joanne Koong.

15) Make non-prealloced BPF map allocations low priority to play better with
    memcg limits, from Yafang Shao.

16) Fix BPF test runner to reject zero-length data for skbs, from Zhengchao Shao.

17) Various smaller cleanups and improvements all over the place.

* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (73 commits)
  bpf: Simplify bpf_prog_pack_[size|mask]
  bpf: Support bpf_trampoline on functions with IPMODIFY (e.g. livepatch)
  bpf, x64: Allow to use caller address from stack
  ftrace: Allow IPMODIFY and DIRECT ops on the same function
  ftrace: Add modify_ftrace_direct_multi_nolock
  bpf/selftests: Fix couldn't retrieve pinned program in xdp veth test
  bpf: Fix build error in case of !CONFIG_DEBUG_INFO_BTF
  selftests/bpf: Fix test_verifier failed test in unprivileged mode
  selftests/bpf: Add negative tests for new nf_conntrack kfuncs
  selftests/bpf: Add tests for new nf_conntrack kfuncs
  selftests/bpf: Add verifier tests for trusted kfunc args
  net: netfilter: Add kfuncs to set and change CT status
  net: netfilter: Add kfuncs to set and change CT timeout
  net: netfilter: Add kfuncs to allocate and insert CT
  net: netfilter: Deduplicate code in bpf_{xdp,skb}_ct_lookup
  bpf: Add documentation for kfuncs
  bpf: Add support for forcing kfunc args to be trusted
  bpf: Switch to new kfunc flags infrastructure
  tools/resolve_btfids: Add support for 8-byte BTF sets
  bpf: Introduce 8-byte BTF set
  ...
====================

Link: https://lore.kernel.org/r/20220722221218.29943-1-daniel@iogearbox.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull in Pavel's patch from a shared branch.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Because of how struct msghdr is usually initialised some fields and
sg_from_iter in particular might be left out not initialised, so we
can't safely use it in __zerocopy_sg_from_iter().

For now use the callback only when there is ->msg_ubuf set relying on
the fact that they're used together and we properly zero ->msg_ubuf.

Fixes: ebe73a28 ("net: Allow custom iter handler in msghdr")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Message-Id: <ce8b68b41351488f79fd998b032b3c56e9b1cc6c.1658401817.git.asml.silence@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Do devl_unlock() before freeing the devlink in
mlxsw_core_bus_device_unregister() function.
Reported-by: Ido Schimmel <idosch@nvidia.com>
Fixes: 72a4c8c9 ("mlxsw: convert driver to use unlocked devlink API during init/fini")
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20220721142424.3975704-1-jiri@resnulli.usSigned-off-by: Jakub Kicinski <kuba@kernel.org>

This introduces hci_recv_event_data to make it simpler to access the
contents of last received event rather than having to pass its contents
to the likes of *_ind/*_cfm callbacks.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Simplify the logic that selects bpf_prog_pack_size, and always use
(PMD_SIZE * num_possible_nodes()). This is a good tradeoff, as most of
the performance benefit observed is from less direct map fragmentation [0].

Also, module_alloc(4MB) may not allocate 4MB aligned memory. Therefore,
we cannot use (ptr & bpf_prog_pack_mask) to find the correct address of
bpf_prog_pack. Fix this by checking the header address falls in the range
of pack->ptr and (pack->ptr + bpf_prog_pack_size).

  [0] https://lore.kernel.org/bpf/20220707223546.4124919-1-song@kernel.org/Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/bpf/20220713204950.3015201-1-song@kernel.org

When tracing a function with IPMODIFY ftrace_ops (livepatch), the bpf
trampoline must follow the instruction pointer saved on stack. This needs
extra handling for bpf trampolines with BPF_TRAMP_F_CALL_ORIG flag.

Implement bpf_tramp_ftrace_ops_func and use it for the ftrace_ops used
by BPF trampoline. This enables tracing functions with livepatch.

This also requires moving bpf trampoline to *_ftrace_direct_mult APIs.
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/all/20220602193706.2607681-2-song@kernel.org/
Link: https://lore.kernel.org/bpf/20220720002126.803253-5-song@kernel.org

Currently we call the original function by using the absolute address
given at the JIT generation. That's not usable when having trampoline
attached to multiple functions, or the target address changes dynamically
(in case of live patch). In such cases we need to take the return address
from the stack.

Adding support to retrieve the original function address from the stack
by adding new BPF_TRAMP_F_ORIG_STACK flag for arch_prepare_bpf_trampoline
function.

Basically we take the return address of the 'fentry' call:

   function + 0: call fentry    # stores 'function + 5' address on stack
   function + 5: ...

The 'function + 5' address will be used as the address for the
original function to call.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220720002126.803253-4-song@kernel.org

IPMODIFY (livepatch) and DIRECT (bpf trampoline) ops are both important
users of ftrace. It is necessary to allow them work on the same function
at the same time.

First, DIRECT ops no longer specify IPMODIFY flag. Instead, DIRECT flag is
handled together with IPMODIFY flag in __ftrace_hash_update_ipmodify().

Then, a callback function, ops_func, is added to ftrace_ops. This is used
by ftrace core code to understand whether the DIRECT ops can share with an
IPMODIFY ops. To share with IPMODIFY ops, the DIRECT ops need to implement
the callback function and adjust the direct trampoline accordingly.

If DIRECT ops is attached before the IPMODIFY ops, ftrace core code calls
ENABLE_SHARE_IPMODIFY_PEER on the DIRECT ops before registering the
IPMODIFY ops.

If IPMODIFY ops is attached before the DIRECT ops, ftrace core code calls
ENABLE_SHARE_IPMODIFY_SELF in __ftrace_hash_update_ipmodify. Owner of the
DIRECT ops may return 0 if the DIRECT trampoline can share with IPMODIFY,
so error code otherwise. The error code is propagated to
register_ftrace_direct_multi so that onwer of the DIRECT trampoline can
handle it properly.

For more details, please refer to comment before enum ftrace_ops_cmd.
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Link: https://lore.kernel.org/all/20220602193706.2607681-2-song@kernel.org/
Link: https://lore.kernel.org/all/20220718055449.3960512-1-song@kernel.org/
Link: https://lore.kernel.org/bpf/20220720002126.803253-3-song@kernel.org

This is similar to modify_ftrace_direct_multi, but does not acquire
direct_mutex. This is useful when direct_mutex is already locked by the
user.
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Link: https://lore.kernel.org/bpf/20220720002126.803253-2-song@kernel.org

The timed ending of Discoverability was handled in hci_requst.c, with
calls using the deprecated hci_req_add() mechanism. Converted to live
inside mgmt.c using the same delayed work queue, but with hci_sync
version of hci_update_discoverable().
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This removes the remaining calls to HCI_OP_WRITE_SCAN_ENABLE from
hci_request call chains, and converts them to hci_sync calls.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The discov_update work queue is no longer used as a result
of the hci_sync rework.

The __hci_req_hci_power_on() function is no longer referenced in the
code as a result of the hci_sync rework.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Delete the repeated word "that" in comments.
Signed-off-by: shaomin Deng <dengshaomin@cdjrlc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This removes the use of hci_conn_hold from Get Conn Info and Get Clock
Info since the callback can just do a lookup by address using the cmd
data and only then set cmd->user_data to pass to the complete callback.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Before change:

  selftests: bpf: test_xdp_veth.sh
  Couldn't retrieve pinned program '/sys/fs/bpf/test_xdp_veth/progs/redirect_map_0': No such file or directory
  selftests: xdp_veth [SKIP]
  ok 20 selftests: bpf: test_xdp_veth.sh # SKIP

After change:

  PING 10.1.1.33 (10.1.1.33) 56(84) bytes of data.
  64 bytes from 10.1.1.33: icmp_seq=1 ttl=64 time=0.320 ms
  --- 10.1.1.33 ping statistics ---
  1 packets transmitted, 1 received, 0% packet loss, time 0ms
  rtt min/avg/max/mdev = 0.320/0.320/0.320/0.000 ms
  selftests: xdp_veth [PASS]

For the test case, the following can be found:

  ls /sys/fs/bpf/test_xdp_veth/progs/redirect_map_0
  ls: cannot access '/sys/fs/bpf/test_xdp_veth/progs/redirect_map_0': No such file or directory
  ls /sys/fs/bpf/test_xdp_veth/progs/
  xdp_redirect_map_0  xdp_redirect_map_1  xdp_redirect_map_2
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jie2x Zhou <jie2x.zhou@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220719082430.9916-1-jie2x.zhou@intel.com

BTF_ID_FLAGS macro needs to be able to take 0 or 1 args, so make it a
variable argument. BTF_SET8_END is incorrect, it should just be empty.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: ab21d606 ("bpf: Introduce 8-byte BTF set")
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20220722113605.6513-1-memxor@gmail.comSigned-off-by: Alexei Starovoitov <ast@kernel.org>

This patch adds missing includes to headers under include/net.
All these problems are currently masked by the existing users
including the missing dependency before the broken header.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Edward Cree says:

====================
sfc: VF representors for EF100

This series adds representor netdevices for EF100 VFs, as a step towards
 supporting TC offload and vDPA usecases in future patches.
In this first series is basic netdevice creation and packet TX; the
 following series will add the RX path.

v3: dropped massive mcdi_pcol.h patch which was applied separately.
v2: converted comments on struct efx_nic members added in patch #4 to
 kernel-doc (Jakub).  While at it, also gave struct efx_rep its own kdoc
 since several members had comments on them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since representors piggy-back on the PF's queues for TX, they can
 only accept new TXes while the PF is up.  Thus, any operation which
 detaches the PF must first detach all its VFreps.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement .ndo_start_xmit() by calling into the parent PF's TX path.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>