- 16 Mar, 2021 11 commits
-
-
Shannon Nelson authored
Gather the Tx packet and byte counts and call netdev_tx_completed_queue() only once per clean cycle. Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Shannon Nelson authored
The descriptor mappings are set up the same way whether or not it is a TSO, so we don't need separate logic for the two cases. Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Shannon Nelson authored
Make the new ionic_tx_map_tso() usable by the non-TSO paths, and pull the call up a level into ionic_tx() before calling the csum or no-csum routines. Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Shannon Nelson authored
One issue with the original TSO code was that it was working too hard to deal with skb layouts that were never going to show up, such as an skb->data that was longer than a single descriptor's length. The other issue was trying to arrange the fragment dma mapping at the same time as figuring out the descriptors needed. There was just too much going on at the same time. Now we do the dma mapping first, which sets up the buffers with skb->data in buf[0] and the remaining frags in buf[1..n-1]. Next we spread the bufs across the descriptors needed, where each descriptor gets up to mss number of bytes. Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Alex Elder says: ==================== net: qualcomm: rmnet: stop using C bit-fields Version 6 is the same as version 5, but has been rebased on updated net-next/master. With any luck, the patches I'm sending out this time won't contain garbage. Version 5 of this series responds to a suggestion made by Alexander Duyck, to determine the offset to the checksummed range of a packet using skb_network_header_len() on patch 2. I have added his Reviewed-by tag to all (other) patches, and removed Bjorn's from patch 2. The change required some updates to the subsequent patches, and I reordered some assignments in a minor way in the last patch. I don't expect any more discussion on this series (but will respond if there is any). So at this point I would really appreciate it if KS and/or Sean would offer a review, or at least acknowledge it. I presume you two are able to independently test the code as well, so I request that, and hope you are willing to do so. Version 4 of this series is here: https://lore.kernel.org/netdev/20210315133455.1576188-1-elder@linaro.org ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alex Elder authored
Replace the use of C bit-fields in the rmnet_map_ul_csum_header structure with a single two-byte (big endian) structure member, and use masks to encode or get values within it. The content of these fields can be accessed using simple bitwise AND and OR operations on the (host byte order) value of the new structure member. Previously rmnet_map_ipv4_ul_csum_header() would update C bit-field values in host byte order, then forcibly fix their byte order using a combination of byte swap operations and types. Instead, just compute the value that needs to go into the new structure member and save it with a simple byte-order conversion. Make similar simplifications in rmnet_map_ipv6_ul_csum_header(). Finally, in rmnet_map_checksum_uplink_packet() a set of assignments zeroes every field in the upload checksum header. Replace that with a single memset() operation. Signed-off-by: Alex Elder <elder@linaro.org> Reviewed-by: Alexander Duyck <alexanderduyck@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alex Elder authored
Replace the use of C bit-fields in the rmnet_map_dl_csum_trailer structure with a single one-byte field, using constant field masks to encode or get at embedded values. Signed-off-by: Alex Elder <elder@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Alexander Duyck <alexanderduyck@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alex Elder authored
The actual layout of bits defined in C bit-fields (e.g. int foo : 3) is implementation-defined. Structures defined in <linux/if_rmnet.h> address this by specifying all bit-fields twice, to cover two possible layouts. I think this pattern is repetitive and noisy, and I find the whole notion of compiler "bitfield endianness" to be non-intuitive. Stop using C bit-fields for the command/data flag and the pad length fields in the rmnet_map structure, and define a single-byte flags field instead. Define a mask for the single-bit "command" flag, and another mask for the encoded pad length. The content of both fields can be accessed using a simple bitwise AND operation. Signed-off-by: Alex Elder <elder@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Alexander Duyck <alexanderduyck@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alex Elder authored
The following macros, defined in "rmnet_map.h", assume a socket buffer is provided as an argument without any real indication this is the case. RMNET_MAP_GET_MUX_ID() RMNET_MAP_GET_CD_BIT() RMNET_MAP_GET_PAD() RMNET_MAP_GET_CMD_START() RMNET_MAP_GET_LENGTH() What they hide is pretty trivial accessing of fields in a structure, and it's much clearer to see this if we do these accesses directly. So rather than using these accessor macros, assign a local variable of the map header pointer type to the socket buffer data pointer, and derereference that pointer variable. In "rmnet_map_data.c", use sizeof(object) rather than sizeof(type) in one spot. Also, there's no need to byte swap 0; it's all zeros irrespective of endianness. Signed-off-by: Alex Elder <elder@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Alexander Duyck <alexanderduyck@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alex Elder authored
In rmnet_map_ipv4_ul_csum_header() and rmnet_map_ipv6_ul_csum_header() the offset within a packet at which checksumming should commence is calculated. This calculation involves byte swapping and a forced type conversion that makes it hard to understand. Simplify this by computing the offset in host byte order, then converting the result when assigning it into the header field. Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alex Elder authored
The fields in the checksum trailer structure used for QMAP protocol RX packets are all big-endian format, so define them that way. It turns out these fields are never actually used by the RMNet code. The start offset is always assumed to be zero, and the length is taken from the other packet headers. So making these fields explicitly big endian has no effect on the behavior of the code. Signed-off-by: Alex Elder <elder@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Alexander Duyck <alexanderduyck@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 15 Mar, 2021 20 commits
-
-
Alex Elder authored
In review, Alexander Duyck suggested that ipa_table_hash_support() was trivial enough that it could be implemented as a static inline function in the header file. But the patch had already been accepted. Implement his suggestion. Signed-off-by: Alex Elder <elder@linaro.org> Reviewed-by: Alexander Duyck <alexanderduyck@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ivan Bornyakov authored
Add basic support for the Marvell 88X2222 multi-speed ethernet transceiver. This PHY provides data transmission over fiber-optic as well as Twinax copper links. The 88X2222 supports 2 ports of 10GBase-R and 1000Base-X on the line-side interface. The host-side interface supports 4 ports of 10GBase-R, RXAUI, 1000Base-X and 2 ports of XAUI. This driver, however, supports only XAUI on the host-side and 1000Base-X/10GBase-R on the line-side, for now. The SGMII is also supported over 1000Base-X. Interrupts are not supported. Internal registers access compliant with the Clause 45 specification. Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Joakim Zhang says: ==================== net: stmmac: implement clocks management This patch set tries to implement clocks management, and takes i.MX platform as an example. --- ChangeLogs: V1->V2: * change to pm runtime mechanism. * rename function: _enable() -> _config() * take MDIO bus into account, it needs clocks when interface is closed. * reverse Christmass tree. V2->V3: * slightly simple the code according to Andrew's suggesstion and also add tag: Reviewed-by: Andrew Lunn <andrew@lunn.ch> ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Joakim Zhang authored
Split clocks settings from init callback into clks_config callback, which could support platform level clocks management. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Joakim Zhang authored
This patch intends to add platform level clocks management. Some platforms may have their own special clocks, they also need to be managed dynamically. If you want to manage such clocks, please implement clks_config callback. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Joakim Zhang authored
This patch intends to add clocks management for stmmac driver: If CONFIG_PM enabled: 1. Keep clocks disabled after driver probed. 2. Enable clocks when up the net device, and disable clocks when down the net device. If CONFIG_PM disabled: Keep clocks always enabled after driver probed. Note: 1. It is fine for ethtool, since the way of implementing ethtool_ops::begin in stmmac is only can be accessed when interface is enabled, so the clocks are ticked. 2. The MDIO bus has a different life cycle to the MAC, need ensure clocks are enabled when _mdio_read/write() need clocks, because these functions can be called while the interface it not opened. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Ong Boon Leong says: ==================== net: pcs, stmmac: add C37 AN SGMII support This patch series adds MAC-side SGMII support to stmmac driver and it is changed as follow:- 1/6: Refactor the current C73 implementation in pcs-xpcs to prepare for adding C37 AN later. 2/6: Add MAC-side SGMII C37 AN support to pcs-xpcs 3,4/6: make phylink_parse_mode() to work for non-DT platform so that we can use stmmac platform_data to set it. 5/6: Make stmmac_open() to only skip PHY init if C73 is used, otherwise C37 AN will need phydev to be connected to phylink. 6/6: Finally, add pcs-xpcs SGMII interface support to Intel mGbE controller. The patch series have been tested on EHL CRB PCH TSN (eth2) controller that has Marvell 88E1512 PHY attached over SGMII interface and the iterative tests of speed change (AN) + ping test have been successful. [63446.009295] intel-eth-pci 0000:00:1e.4 eth2: Link is Down [63449.986365] intel-eth-pci 0000:00:1e.4 eth2: Link is Up - 1Gbps/Full - flow control off [63449.987625] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [63451.248064] intel-eth-pci 0000:00:1e.4 eth2: Link is Down [63454.082366] intel-eth-pci 0000:00:1e.4 eth2: Link is Up - 100Mbps/Full - flow control off [63454.083650] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [63456.465179] intel-eth-pci 0000:00:1e.4 eth2: Link is Down [63459.202367] intel-eth-pci 0000:00:1e.4 eth2: Link is Up - 10Mbps/Full - flow control off [63459.203639] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready [63460.882832] intel-eth-pci 0000:00:1e.4 eth2: Link is Down [63464.322366] intel-eth-pci 0000:00:1e.4 eth2: Link is Up - 1Gbps/Full - flow control off ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ong Boon Leong authored
Intel mGbE controller such as those in EHL & TGL uses pcs-xpcs driver for SGMII interface. To ensure mdio bus scanning does not assign phy_device to MDIO-addressable entities like intel serdes and pcs-xpcs, we set up to phy_mask to skip them. Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ong Boon Leong authored
As the support for MAC-side SGMII C37 AN is added to pcs-xpcs, phydev should be attached to phylink during driver's open(). So, we change the condition to "Not C73 AN" instead. Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ong Boon Leong authored
Not all platform uses DT, so phylink_parse_mode() will skip in-band setup of pl->supported and pl->link_config.advertising entirely. So, we add the setting of ovr_an_inband flag to make it works for non-DT platform. Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ong Boon Leong authored
Certain platform does not support DT, so we make phylink_parse_mode() to allow non-DT platform to use it to setup in-band AN advertising. Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ong Boon Leong authored
XPCS IP supports C37 SGMII AN process and it is used in intel multi-GbE controller as MAC-side SGMII. Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ong Boon Leong authored
The current implementation for XPCS is validated for C73, so we rename them to have _c73 suffix and introduce a set of functions to use an_mode flag to switch between C73 and C37 AN later. Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Bhaskar Chowdhury authored
s/structue/structure/ Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Bhaskar Chowdhury authored
s/structue/structure/ Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Bhaskar Chowdhury authored
Mundane typo fix. Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Shay Agroskin <shayagr@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alexey Dobriyan authored
This file has been effectively empty since 2.3.99-pre3 ! Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jianlin Lv authored
When the incorrect interface name is stored in the slaves/active_slave option of the bonding sysfs, the kernel does not record the log that interface does not exist. This patch adds a log for -ENODEV error, which will facilitate users to figure out such issue. Signed-off-by: Jianlin Lv <Jianlin.Lv@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lorenzo Bianconi authored
For wireless devices (e.g. mt76 driver) multiple net_devices belongs to the same wireless phy and the napi object is registered in a dummy netdevice related to the wireless phy. Export dev_set_threaded in order to be reused in device drivers enabling threaded NAPI. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Kurt Kanzenbach authored
The switch implements unicast and multicast filtering per port. Add support for it. By default filtering is disabled. Signed-off-by: Kurt Kanzenbach <kurt@kmk-computers.de> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 14 Mar, 2021 9 commits
-
-
David S. Miller authored
Ido Schimmel says: ==================== psample: Add additional metadata attributes This series extends the psample module to expose additional metadata to user space for packets sampled via act_sample. The new metadata (e.g., transit delay) can then be consumed by applications such as hsflowd [1] for better network observability. netdevsim is extended with a dummy psample implementation that periodically reports "sampled" packets to the psample module. In addition to testing of the psample module, it enables the development and demonstration of user space applications (e.g., hsflowd) that are interested in the new metadata even without access to specialized hardware (e.g., Spectrum ASIC) that can provide it. mlxsw is also extended to provide the new metadata to psample. A Wireshark dissector for psample netlink packets [2] will be submitted upstream after the kernel patches are accepted. In addition, a libpcap capture module for psample is currently in the works. Eventually, users should be able to run: # tshark -i psample In order to consume sampled packets along with their metadata. Series overview: Patch #1 makes it easier to extend the metadata provided to psample Patch #2 adds the new metadata attributes to psample Patch #3 extends netdevsim to periodically report "sampled" packets to psample. Various debugfs knobs are added to control the reporting Patch #4 adds a selftest over netdevsim Patches #5-#10 gradually add support for the new metadata in mlxsw Patch #11 adds a selftest over mlxsw [1] https://sflow.org/draft4_sflow_transit.txt [2] https://gitlab.com/amitcohen1/wireshark/-/commit/3d711143024e032aef1b056dd23f0266c54fab56 ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
Test that packets are sampled when tc-sample is used and that reported metadata is correct. Two sets of hosts (with and without LAG) are used, since metadata extraction in mlxsw is a bit different when LAG is involved. # ./tc_sample.sh TEST: tc sample rate (forward) [ OK ] TEST: tc sample rate (local receive) [ OK ] TEST: tc sample maximum rate [ OK ] TEST: tc sample group conflict test [ OK ] TEST: tc sample iif [ OK ] TEST: tc sample lag iif [ OK ] TEST: tc sample oif [ OK ] TEST: tc sample lag oif [ OK ] TEST: tc sample out-tc [ OK ] TEST: tc sample out-tc-occ [ OK ] Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
Make use of the previously added metadata and report it to the psample module. The metadata is read from the skb's control block, which was initialized by the bus driver (i.e., 'mlxsw_pci') after decoding the packet's Completion Queue Element (CQE). Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
The function resolves the psample sampling group from the Rx port because this is the only form of sampling the driver currently supports. Subsequent patches are going to add support for Tx-based and policy-based sampling, in which case the sampling group would not be resolved from the Rx port. Therefore, move this code to the Rx-specific sampling listener. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
Since commit 7d8e8f34 ("mlxsw: core: Increase scope of RCU read-side critical section"), all Rx handlers are called from an RCU read-side critical section. Remove the unnecessary rcu_read_lock() / rcu_read_unlock(). Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
Packets that are mirrored / sampled to the CPU have extra metadata encoded in their corresponding Completion Queue Element (CQE). Retrieve this metadata from the CQE and set it in the skb control block so that it could be accessed by the switch driver (i.e., 'mlxsw_spectrum'). Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
Next patch will need to encode more Rx metadata in the skb control block, so create a dedicated field for it and move the cookie index there. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
The Completion Queue Element version 2 (CQEv2) includes various metadata fields for packets that are mirrored / sampled to the CPU. Add these fields so that they could be used by a later patch. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ido Schimmel authored
Test various aspects of psample functionality over netdevsim and in particular test that the psample module correctly reports the provided metadata. Example: # ./psample.sh TEST: psample enable / disable [ OK ] TEST: psample group number [ OK ] TEST: psample metadata [ OK ] Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-