This avoids impossible platform combinations, as we cannot
build a combined V5 + V6/V7 kernel.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

From Shawn Guo:

imx soc changes for 3.11:

* New SoCs i.MX6 Sololite and Vybrid VF610 support
* imx5 and imx6 clock fixes and additions
* Update clock driver to use of_clk_init() function
* Refactor restart routine mxc_restart() to get it work for DT boot
  as well
* Clean up mxc specific ulpi access ops
* imx defconfig updates

* tag 'imx-soc-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6: (29 commits)
  ARM: imx_v6_v7_defconfig: Enable Vybrid VF610
  ARM: imx_v6_v7_defconfig: Enable imx-wm8962 by default
  ARM: clk-imx6qdl: Add clko1 configuration for imx6qdl-sabresd
  ARM: imx_v6_v7_defconfig: Enable PWM and backlight options
  ARM: imx: Remove mxc specific ulpi access ops
  ARM: imx: add initial support for VF610
  ARM: imx: add VF610 clock support
  ARM: imx_v6_v7_defconfig: enable parallel display
  ARM: imx: clk: No need to initialize phandle struct
  ARM: imx: irq-common: Include header to avoid sparse warning
  ARM: imx: Enable mx6 solo-lite support
  ARM: imx6: use common of_clk_init() call to initialize clocks
  ARM: imx6q: call of_clk_init() to register fixed rate clocks
  ARM: imx: imx_v6_v7_defconfig: Select CONFIG_DRM_IMX_TVE
  ARM: i.MX6: clk: add different DualLite MLB clock config
  ARM i.MX5: Add S/PDIF clocks
  ARM i.MX53: Add SATA clock
  ARM: imx6q: clk: add the eim_slow clock
  ARM: imx: remove MLB PLL from pllv3
  ARM: imx: disable pll8_mlb in mx6q_clks
  ...

Conflicts:
	arch/arm/Kconfig.debug (simple add/add conflict)

Includes an update to 3.10-rc6
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'u300-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/soc

From Linus Walleij:

Device Tree and Multiplatform support for U300:
- Add devicetree support to timer, pinctrl (probe), I2C block,
  watchdog, DMA controller and clocks.
- Piecewise add a device tree containing all peripherals.
- Delete the ATAG boot path.
- Delete redundant platform data and board files.
- Convert to multiplatform.

* tag 'u300-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (40 commits)
  ARM: u300: switch to using syscon regmap for board
  ARM: u300: Update MMC configs for u300 defconfig
  spi: pl022: use DMA by default when probing from DT
  pinctrl: get rid of all platform data for coh901
  ARM: u300: convert MMC/SD clock to device tree
  ARM: u300: move the gated system controller clocks to DT
  i2c: stu300: do not request a specific clock name
  clk: move the U300 fixed and fixed-factor to DT
  ARM: u300: remove register definition file
  ARM: u300: add syscon node
  ARM: u300 use module_spi_driver to register driver
  ARM: u300: delete remnant machine headers
  ARM: u300: convert to multiplatform
  ARM: u300: localize <mach/u300-regs.h>
  ARM: u300: delete <mach/irqs.h>
  ARM: u300: delete <mach/hardware.h>
  ARM: u300: push down syscon registers
  ARM: u300: remove deps from debug macro
  ARM: u300: move debugmacro to debug includes
  ARM: u300: delete all static board data
  ...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'integrator-pci-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/soc

From Linus Walleij:

This is a patch series that:
- Pulls the Integrator/AP PCI bridge driver into one file
- Adds full device tree support for it
- Keeps ATAG support around for the time being

* tag 'integrator-pci-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
  ARM: integrator: basic PCIv3 device tree support
  ARM: integrator: move static ioremapping into PCIv3 driver
  ARM: integrator: move VGA base assignment
  ARM: integrator: remap PCIv3 base dynamically
  ARM: integrator: move V3 register definitions into driver
  ARM: integrator: move PCI base address grab to probe
  ARM: integrator: grab PCI error IRQ in probe()
  ARM: integrator: convert PCIv3 bridge to platform device
  ARM: integrator: merge PCIv3 driver into one file
  ARM: pci: create pci_common_init_dev()
  Documentation/devicetree: add a small note on PCI
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'keystone-soc-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/soc

From Santosh Shilimkar:
SOC support for Keystone II devices:
- Minimal machine and device-tree support with arch_timers and console UART
- Reboot hook using PLL reset
- Low level debug support using UART
- SMP boot support

* tag 'keystone-soc-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
  ARM: keystone: Enable SMP support on Keystone machines
  ARM: keystone: Add minimal TI Keystone platform support
  ARM: dts: keystone: Add minimal Keystone SOC device tree data
Signed-off-by: Olof Johansson <olof@lixom.net>

Add basic SMP support for Keystone machines. This does not
include support for CPU hotplug for now.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: arm@kernel.org
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Texas Instruments Keystone family of multi-core devices are
based on ARM Cortex A15. Patch adds basic definitions for a
new Keystone sub-architecture in ARM.

The TCI66xxK2H Communications Infrastructure Keystone SoCs
are member of the C66x family based on TI's new KeyStone 2
multi-core SoC Architecture designed specifically for high
performance wireless and networking infrastructure applications.
The SOCs contains many subsystems like Cortex A15 ARM CorePacs,
C66XX DSP CorePacs, MSMC memory controller, Tera Net bus,
IP Network, Navigator, Hyperlink, 1G/10G Ethernet, Radio layers
and queue based communication systems.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: arm@kernel.org
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Add minimal device tree data for Keystone2 based SOCs. Patch
contains mainly ARM related SOC data and nothing about EVM specific
yet.

Cc: Grant Likely <grant.likely@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: arm@kernel.org
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

This switches the code using a local remapping of the
system controller to enable the U300 board to be
self-powered over to making the U300-specific syscon
compatible with the MFD generic syscon driver, selecting
the generic syscon driver, and augmenting the board
power code to pick the regmap and manipulate the syscon
from the regmap side of things.

Cc: Dong Aisheng <dong.aisheng@linaro.org>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Enable MMC_UNSAFE_RESUME to be accomplish a proper suspend/resume cycle
for SD/SDIO/(e)MMC.

ARMMMCI host driver supports clock gating through runtime PM, thus
MMC_CLKGATE is not needed. Moreover ARMMMCI can do scatter-gather which
means we can explicity disable MMC_BLOCK_BOUNCE, since it's default
enabled, to skip unnecessary bounce buffer copying.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

In the past we controlled the selection of DMA for a certain
host by a boolean switch in the platform data. Currently
there is no way to enable DMA on a PL022 probed from the
device tree. Let's default to trying to obtain DMA channels
in the DT case, and then we can always fail (and thus fall
back to PIO mode).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This deletes the dependency on any platform data for
the COH901 pin controller. There is only one user in the
kernel, and if we at some point want to support more
variants, they shall provide their variant info through
the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This converts the last of the U300 clocks to being probed from
the device tree.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This moves the slow, fast, AHB bridge and "rest" clocks on
the U300 system controller over to registration from the
device tree.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We have used the default clock associated with the block
for a long time, only heuristics in the clock system has
made this work anyway. This needs to be done away with as
we start probing this driver and its clocks exclusively
from the device tree.
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This converts the fixed and fixed-factor clocks in the U300
platform to register themselves from the device tree.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Now that the core file is the only one actually using any
of the base addresses, we can delete that header and move
the base address definitions into the one and only core
file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds a device tree node for the U300 system controller
and remaps this dynamically instead of using hard-coded
virtual addresses. The board power set-up code is altered
to fetch a reference to the syscon using ampersand <&syscon>
notation. This way of passing a pointer to the syscon will
also be used by the clocks.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Removing some boilerplate by using module_spi_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Two files remain in <mach/*> for U300: timex.h and
uncompress.h. The former is done away with by using
defaults, the latter is unused in multiplatform.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Now that we removed our dependency on <mach/*> the U300
can be converted to mutliplatform. Remove the invalid restriction
that U300 would not support AUTO_ZRELADDR (it does) and update
the defconfig in the process.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This register base file is now only used in the machine
itself so move it down into mach-u300.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

All IRQs are now obtained from the device tree, and this file
is unused, so delete it.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This file is now unused and can be deleted.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Get rid of the <mach/syscon.h> header as a prerequisite for
multiplatform support. Do this by pushing the registers down
to their respective drivers and deleting the unused remainder.
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This rids the dependency to <mach/hardware.h> (which is an
implicit dependency to <mach/u300-regs.h>) from the U300
debug macro. Take this opportunity to update the file
header.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This moves the U300 debug macro to the debug headers to
make way for multiplatform support.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We have now transferred all the U300 peripherals to the device
tree, so we just select USE_OF, and delete all static board data,
then require that this platform shall be booted using the device
tree and nothing else.

This gets rid of the MMCI (PL180), PL022, and serial PL011
platform data entries and more.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This registers the U300 FSMC flash controller from the
device tree, and defines the three partitions. Skip the
BBT scan as in the current platform data.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This probes the U300 dummy-spichip from the device tree
and adds the apropriate node to the tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This registers the PL022 PrimeCell from the U300 device
tree. We make a new copy of the platform data for the
device tree boot path, as the old platform data is in an
older file which will be going away.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds the COH 901 318 DMA controller to the U300
device tree. All devices now converted to device tree
so far will start to find their DMA channels.

Note that the U300 is not yet using the device tree
to obtain DMA channels, but this is a first step.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds DMA channel assignments to the MMC/SD-controller
and the two UARTs already in the U300 device tree, as we
have now defined a way to obtain DMA channels from the
device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds support for probing the COH 901 318 DMA controller
and channels from the device tree.

Contains portions of a sketch patch from Arnd Bergmann.

Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds support for the U300 MMC/SD card slot from the device
tree boot. No other changes needed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Now that we have enabled board power and the AB3100 regulators,
put the regulator data into the device tree and enable it so
we can start to tie regulators to devices. To begin with we're
only supplying the power to the board itself.

Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds support for setting up the board power from the
device tree on the U300. We use a board-specific node in the
device tree for the S365 board and bind a regulator for the
board power to this node.

Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds the COH 901 331 RTC to the U300 device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This add devicetree probe support to the COH 901 331 RTC
driver.

Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Let VF610 SoC support be built by default.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>