This introduces qed_ll2_comp_rx_data as a public struct
and moves handling of Rx packets in LL2 into using it.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

First step in revising the LL2 interface, this declares
qed_ll2_tx_pkt_info as part of the ll2 interface, and uses it for
transmission instead of receiving lots of parameters.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hayes Wang says:

====================
r8152: minor adjustment

Adjust some code to make it reasonable or satisfy the suggestion from
the engineers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Change from using napi_complete to napi_complete_done to allow for the
use of gro_flush_timeout in tuning network processing.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stop queuing rx packets if it is more than 1000.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use PLA 0xe000 bit 8 to check if disabling ALDPS is finished.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move tp->rtl_ops.init() from rtl8152_resume() to rtl8152_reset_resume().
The initialization is only necessary for reset_resume().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only RTL8153 could set coalesce, so move the default setting for
rtl8152_probe() to r8153_init().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use another way to keep disabling the U2P3 for both RTL_VER_03 and
RTL_VER_04.

Move enabling U2P3 from r8153_init() to r8153_hw_phy_cfg(). The
engineer ask the setting should be done after PHY settings.

Disable U2P3 first in rtl8153_up().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adjust the order of rtl8153_runtime_enable() according to the
suggestion from the engineer.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the setting from r8153_first_init() to r8153_init(). It only needs to
be set once.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MAC clock speed down could be enabled if the U1/U2 is disabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable lpm after r8153_init() and remove other enable/disable lpm.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use r8153_phy_status() to check phy status of RTL8153.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

llvm 5.0 does not like the section name and the function name
to be the same:

clang -I. -I./include/uapi -I../../../include/uapi \
	-I../../../../samples/bpf/ \
	-Wno-compare-distinct-pointer-types \
	-O2 -target bpf -c \
	linux/tools/testing/selftests/bpf/test_obj_id.c -o \
	linux/tools/testing/selftests/bpf/test_obj_id.o
fatal error: error in backend: 'test_prog_id' label emitted multiple times to
assembly file
clang-5.0: error: clang frontend command failed with exit code 70 (use -v to
see invocation)
clang version 5.0.0 (trunk 304326) (llvm/trunk 304329)

This patch makes changes to the section name and the function name.

Fixes: 95b9afd3 ("bpf: Test for bpf ID")
Reported-by: Alexei Starovoitov <ast@fb.com>
Reported-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

test_bpf_obj_id() should not expect a non zero jited_prog_len
to be returned by bpf_obj_get_info_by_fd() when
net.core.bpf_jit_enable is 0.

The patch checks for net.core.bpf_jit_enable and
has different expectation on jited_prog_len.

This patch also removes the pwd.h header which I forgot
to remove after making changes.

Fixes: 95b9afd3 ("bpf: Test for bpf ID")
Reported-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the initialization of skb->dev and skb->protocol from
ip6_finish_output2 to ip6_output. This can make the skb->dev and
skb->protocol information avalaible to the CGROUP eBPF filter.
Signed-off-by: Chenbo Feng <fengc@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Handle TIMER0INT when FW crashes. Check for PCIE_FW[FW_EVAL]
and if it says "Device FW Crashed", then treat it as fatal.
Else, non-fatal.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
nfp: FW app build name reporting

This series adds reporting FW build name in ethtool -i.  Most
of the patches are restructuring where information caching is
done.  There is also a minor error path fix.

These are last few patches finishing the basic nfp_app support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure application FW build name is NULL-terminated and
print it as a part of ethtool's firmware version string.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Microcode Information Page contains some useful information, like
application firmware build name.  Keep it around, similar to RTSym
and HWInfo.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make callers take care of managing life time of HWInfo.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The fact that RTsym table is cached inside nfp_cpp handle is
a relic of old times when nfpcore was a library module.  All
the nfp_cpp "caches" are awkward to deal with because of
concurrency and prone to keeping stale information.  Make
the run time symbol table be an object read out from the device
and managed by whoever requested it.  Since the driver loads
FW at ->probe() and never reloads, we can hold onto the table
for ever.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If very last stages of netdev registering and init fail some
other netdevs and devlink ports may have been visible to user
space before we torn them back down.  In this case there is a
slight chance user may have triggered port refresh.  We need
to make sure the async work is cancelled.

We have to cancel after releasing pf->lock, so we will always
try to cancel, regardless of which part of probe has failed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Disallow enabling firmware debug from a VF.  Only PF is allowed to do that.
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are few places on the receive path where packet drops and packet
errors were not accounted for. This patch fixes that issue.
Signed-off-by: Girish Moodalbail <girish.moodalbail@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ipvlan code already knows how to detect when a duplicate address is
about to be assigned to an ipvlan device.  However, that failure is not
propogated outward and leads to a silent failure.

Introduce a validation step at ip address creation time and allow device
drivers to register to validate the incoming ip addresses.  The ipvlan
code is the first consumer.  If it detects an address in use, we can
return an error to the user before beginning to commit the new ifa in
the networking code.

This can be especially useful if it is necessary to provision many
ipvlans in containers.  The provisioning software (or operator) can use
this to detect situations where an ip address is unexpectedly in use.
Signed-off-by: Krister Johansen <kjlx@templeofstupid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stephen Hemminger says:

====================
netvsc: small cleanups

These are all small optimizations found during development of later features.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

No longer need common code to find get_outbound_net_device.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't need to find netvsc_device structure, caller already had it.
Also rearrange declarations.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mark if() statements used for error handling only as unlikely()
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The element netvsc_device:extension is always a pointer to RNDIS
information.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't need need to look at write space in netvsc_close.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Speed up transmit check for fragmented packets by using existing
macros to compute number of pages, and eliminate loop since
skb fragments each take a page. Number of slots is also unsigned.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vivien Didelot says:

====================
net: dsa: mv88e6xxx: ops cosmetics

This patchset brings no functional changes. It is a first step in a
bigger cosmetics change to the driver. It simplifies print messages and
polishes data types and chip operations.

The next patchs will only prefix and document the port registers macros.

Changes in v2:
  - KISS and simply use dev_* since chip->ds may not be initialized
  - add reviewers tags
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Prefix the PHY_* macros with a Marvell specific MV88E6XXX_ prefix.
There is no functional changes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marvell chips have a Jumbo Mode to set the maximum frame size (MTU).

The mv88e6xxx_ops structure is meant to contain generic functionalities,
no driver logic. Change port_jumbo_config to port_set_jumbo_size setting
the mode from a given maximum size value.

There is no functional changes since we still use 10240 bytes.

At the same time, correctly clear all Jumbo Mode bits before writing.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All Marvell chips supporting Pause frames limiting use 1-byte value for
input and output.

Old chips have both bytes adjacent in a 16-bit register. New ones have
an indirect table using 8-bit data.

The mv88e6xxx library functions (such as in port.c) must not contain
driver logic, but only generic helpers. This patch changes the
port_pause_config operation for port_pause_limit taking two u8 arguments
for input and output limits. There is no functional changes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mv88e6xxx_ops describe functionalities, regardless their locations
(which can be Global1, Global2, or whatever register set.)

Rename the g1_set_cpu_port and g1_set_egress_port ops to set_cpu_port
and set_egress_port. No functional changes.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reuse the BR_STATE_* values to abstract a port STP state value.

This provides shorter names and better control over the DSA switch
operation call.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>