- 25 Nov, 2014 19 commits
-
-
Javier Martinez Canillas authored
This reverts commit b7cde707 ("mfd: sec-core: Prepare regulators for suspend state to reduce power-consumption") Commit b7cde707 called regulator_suspend_prepare() to prepare the regulators for a suspend state. But it did from the device pm suspend handler while the regulator suspend prepare function iterates over all regulators and not only the one managed by this device so it doesn't seems to be correct to call it from within a device driver. It is better to call the regulator suspend prepare/finish functions from platform code instead so this patch reverts the mentioned commit. Suggested-by:
Doug Anderson <dianders@chromium.org> Signed-off-by:
Javier Martinez Canillas <javier.martinez@collabora.co.uk> Reviewed-by:
Chanwoo Choi <cw00.choi@samsung.com> Reviewed-by:
Lee Jones <lee.jones@linaro.org>
-
Krzysztof Kozlowski authored
Add a "maxim,max77693-charger" of_compatible to the mfd_cell so the MFD child device (the charger) will have its own of_node set. This will be used by the max77693 charger driver in next patches to obtain battery configuration from DTS. Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by:
-
Will Sheppard authored
This was found whilst running checkpatch.pl on arizona-spi. WARNING: Missing a blank line after declarations + struct arizona *arizona = spi_get_drvdata(spi); + arizona_dev_exit(arizona); Signed-off-by:
Will Sheppard <wsheppard@embedded-bits.co.uk> Signed-off-by:
-
Krzysztof Kozlowski authored
Remove old MAX77693_NUM_IRQ_MUIC_REGS define. Not used anywhere. Signed-off-by:
-
Boris Brezillon authored
The HLCDC IP available on some Atmel SoCs (i.e. at91sam9n12, at91sam9x5 family or sama5d3 family) exposes 2 subdevices: - a display controller (controlled by a DRM driver) - a PWM chip This patch adds documentation for atmel-hlcdc DT bindings. Signed-off-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Tested-by:
Anthony Harivel <anthony.harivel@emtrion.de> Tested-by:
Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by:
-
Boris Brezillon authored
The HLCDC IP available on some Atmel SoCs (i.e. at91sam9n12, at91sam9x5 family or sama5d3 family) exposes 2 subdevices: - a display controller (controlled by a DRM driver) - a PWM chip The MFD device provides a regmap and several clocks (those connected to this hardware block) to its subdevices. This way concurrent accesses to the iomem range are handled by the regmap framework, and each subdevice can safely access HLCDC registers. Signed-off-by:
-
Johan Hovold authored
Make sure to always honour multi-function devices registered with PLATFORM_DEVID_NONE (-1) or PLATFORM_DEVID_AUTO (-2) as id base. In this case it does not make sense to append the cell id to the mfd-id base and potentially change the requested behaviour. Specifically this will allow multi-function devices to be registered with PLATFORM_DEVID_AUTO while still having non-zero cell ids. Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Johan Hovold authored
Use mfd_add_hotplug_devices() helper to register the subdevices. Compile-only tested. Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Johan Hovold authored
Use mfd_add_hotplug_devices helper to register the subdevices. Signed-off-by:
-
Pankaj Dubey authored
Currently a syscon entity can be only registered directly through a platform device that binds to a dedicated syscon driver. However in certain use cases it is desirable to make a device used with another driver a syscon interface provider. For example, certain SoCs (e.g. Exynos) contain system controller blocks which perform various functions such as power domain control, CPU power management, low power mode control, but in addition contain certain IP integration glue, such as various signal masks, coprocessor power control, etc. In such case, there is a need to have a dedicated driver for such system controller but also share registers with other drivers. The latter is where the syscon interface is helpful. In case of DT based platforms, this patch decouples syscon object from syscon platform driver, and allows to create syscon objects first time when it is required by calling of syscon_regmap_lookup_by APIs and keep a list of such syscon objects along with syscon provider device_nodes and regmap handles. For non-DT based platforms, this patch keeps syscon platform driver structure so that syscon can be probed and such non-DT based drivers can use syscon_regmap_lookup_by_pdev API and access regmap handles. Once all users of "syscon_regmap_lookup_by_pdev" migrated to DT based, we can completely remove platform driver of syscon, and keep only helper functions to get regmap handles. Suggested-by:
Arnd Bergmann <arnd@arndb.de> Suggested-by:
Tomasz Figa <tomasz.figa@gmail.com> Tested-by:
Vivek Gautam <gautam.vivek@samsung.com> Tested-by:
Pankaj Dubey <pankaj.dubey@samsung.com> Reviewed-by:
Heiko Stuebner <heiko@sntech.de> Reviewed-by:
-
Jaewon Kim authored
This patch add haptic DT binding documentation and example to support haptic driver in max77693 Multifunction device. Signed-off-by:
Jaewon Kim <jaewon02.kim@samsung.com> Acked-by:
-
Jaewon Kim authored
This patch add haptic of_compatible in order to use the haptic device driver using Devicetree. Signed-off-by:
-
Jaewon Kim authored
This patch add regmap_haptic initialization to use haptic register map in haptic device driver. Signed-off-by:
-
Johannes Pointner authored
Adds of_compatible strings to mfd_cells for sub devices of the tps65217. Signed-off-by:
Johannes Pointner <johannes.pointner@br-automation.com> Signed-off-by:
-
Lee Jones authored
Merge branches 'ib-mfd-gpio-i2c-3.19', 'ib-mfd-iio-3.19' and 'ib-mfd-regulator-v3.19', tag 'ib-mfd-regulator-clk-v3.19' into ibs-for-mfd-merged Immutable branch between MFD, Regulator and Clk, due for v3.19
-
Chanwoo Choi authored
This patch adds the binding documentation for Samsung S2MPS13 PMIC which is similiar with existing S2MPS14 PMIC. S2MPS13 has the different number of regulators from S2MPS14 and RTC/Clock is the same with the S2MPS14. Signed-off-by:
Sangbeom Kim <sbkim73@samsung.com> Reviewed-by:
-
Chanwoo Choi authored
This patch adds the support for S2MPS13 PMIC clock which is same with existing S2MPS14 RTC IP. But, S2MPS13 uses all of clocks (32khz_{ap|bt|cp}). Signed-off-by:Michael Turquette <mturquette@linaro.org> Signed-off-by:
-
Chanwoo Choi authored
This patch adds S2MPS13 regulator device to existing S2MPS11 device driver. The S2MPS13 has just different number of regulators from S2MPS14. The S2MPS13 regulator device includes LDO[1-40] and BUCK[1-10]. Signed-off-by:
Mark Brown <broonie@kernel.org> Reviewed-by:
-
Chanwoo Choi authored
This patch adds the support for Samsung S2MPS13 PMIC device to the sec-core MFD driver. The S2MPS13 is very similar with existing S2MPS14 and includes PMIC/ RTC/CLOCK devices. Signed-off-by:
-
- 19 Nov, 2014 4 commits
-
-
Dan Carpenter authored
Sparse catches a couple endian bugs. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
Octavian Purdila <octavian.purdila@intel.com> Signed-off-by:
-
Octavian Purdila authored
The echo field in dln2_transfer_complete comes directly from an USB transfer and we should not trust it is valid. Reported-by:
-
Octavian Purdila authored
This fixes the following kbuild test robot warning: >> drivers/i2c/busses/i2c-dln2.c:70:1-4: WARNING: end returns can be simplified if negative or 0 value Reported-by:
kbuild test robot <fengguang.wu@intel.com> Reported-by:
Julia Lawall <julia.lawall@lip6.fr> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Octavian Purdila authored
If wait_for_completion_interruptible_timeout returns a positive value it may be propagated as the return value of _dln2_transfer. This contradicts the documentation of the function and exposes unnecessary internals to the callers. This patch makes sure to set the return value to 0 in that case. Reported-by:
-
- 18 Nov, 2014 3 commits
-
-
Jacob Pan authored
This is no longer needed in that platform driver_register will do it. Signed-off-by:
Jacob Pan <jacob.jun.pan@linux.intel.com> Acked-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Jacob Pan authored
IRQ numbers in axp20x devices are defined with high-order bit first in each IRQ enable/status registers. On Intel platforms it is more common to number IRQs with least significant bit first. Therefore, sharing IRQ# between the two is very difficult. Since AXP288 is a customized PMIC for Intel platform and the amount of shared IRQs are very small, we use separate IRQ numbering. This also fixes collision and a duplicate in WBTO interrupt. e.g. For the 16 interrupts controlled in IRQ enabled registers 1 & 2, on axp20x for ARM, the PMIC local IRQ numbers and register bits are mapped as: IRQ#: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 --------------------------------------------------------- ARM: 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 Intel: 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 Signed-off-by:
Todd Brandt <todd.e.brandt@linux.intel.com> Signed-off-by:
-
Aaron Lu authored
Add the module device id table so that the driver can be automatically loaded once the platform device is created. Signed-off-by:
Aaron Lu <aaron.lu@intel.com> Signed-off-by:
-
- 10 Nov, 2014 4 commits
-
-
Daniel Baluta authored
This patch adds GPIO and IRQ support for the Diolan DLN-2 GPIO module. Information about the USB protocol interface can be found in the Programmer's Reference Manual [1], see section 2.9 for the GPIO module commands and responses. [1] https://www.diolan.com/downloads/dln-api-manual.pdfSigned-off-by:
Daniel Baluta <daniel.baluta@intel.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Reviewed-by:
-
Laurentiu Palcu authored
This patch adds support for the Diolan DLN-2 I2C master module. Due to hardware limitations it does not support SMBUS quick commands. Information about the USB protocol interface can be found in the Programmer's Reference Manual [1], see section 6.2.2 for the I2C master module commands and responses. [1] https://www.diolan.com/downloads/dln-api-manual.pdfSigned-off-by:
Laurentiu Palcu <laurentiu.palcu@intel.com> Signed-off-by:
-
Octavian Purdila authored
This patch implements the USB part of the Diolan USB-I2C/SPI/GPIO Master Adapter DLN-2. Details about the device can be found here: https://www.diolan.com/i2c/i2c_interface.html. Information about the USB protocol can be found in the Programmer's Reference Manual [1], see section 1.7. Because the hardware has a single transmit endpoint and a single receive endpoint the communication between the various DLN2 drivers and the hardware will be muxed/demuxed by this driver. Each DLN2 module will be identified by the handle field within the DLN2 message header. If a DLN2 module issues multiple commands in parallel they will be identified by the echo counter field in the message header. The DLN2 modules can use the dln2_transfer() function to issue a command and wait for its response. They can also register a callback that is going to be called when a specific event id is generated by the device (e.g. GPIO interrupts). The device uses handle 0 for sending events. [1] https://www.diolan.com/downloads/dln-api-manual.pdfSigned-off-by:
-
Johan Hovold authored
Hot-pluggable multi-function devices should always be registered with PLATFORM_DEVID_AUTO to avoid name collisions on the platform bus. This helper also hides the memory map and irq parameters, which aren't used by hot-pluggable (e.g. USB-based) devices. Signed-off-by:
-
- 22 Oct, 2014 1 commit
-
-
Romain Perier authored
Several drivers create their own devicetree property when they register poweroff capabilities. This is for example the case for mfd, regulator or power drivers which define "vendor,system-power-controller" property. This patch adds support for a standard property "poweroff-source" which marks the device as able to shutdown the system. Signed-off-by:
Romain Perier <romain.perier@gmail.com> Acked-by:
Grant Likely <grant.likely@linaro.org> Signed-off-by:
-
- 20 Oct, 2014 2 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds authored
Pull ARM SoC fixes from Olof Johansson: "A batch of fixes that have come in during the merge window. Some of them are defconfig updates for things that have now landed, some errata additions and a few general scattered fixes. There's also a qcom DT update that adds support for SATA on AP148, and basic support for Sony Xperia Z1 and CM-QS600 platforms that seemed isolated enough that we could merge it even if it's late" * tag 'arm-soc-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: MAINTAINERS: corrected bcm2835 search ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa ARM: dts: Explicitly set dr_mode on exynos Peach boards ARM: dts: qcom: add CM-QS600 board ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone ARM: dts: qcom: Add SATA support on IPQ8064/AP148 MAINTAINERS: Update Santosh Shilimkar's email id ARM: sunxi_defconfig: enable CONFIG_REGULATOR ARM: dts: Disable smc91x on n900 until bootloader dependency is removed ARM: omap2plus_defconfig: Enable ARM erratum 430973 for omap3 ARM: exynos_defconfig: enable USB gadget support ARM: exynos_defconfig: Enable Maxim 77693 and I2C GPIO drivers ARM: mm: Fix ifdef around cpu_*_do_[suspend, resume] ops ARM: EXYNOS: Fix build with PM_SLEEP=n and ARM_EXYNOS_CPUIDLE=n ARM: SAMSUNG: Restore Samsung PM Debug functionality ARM: dts: Fix pull setting in sd4_width8 pin group for exynos4x12 ARM: exynos_defconfig: Enable SBS battery support ARM: exynos_defconfig: Enable Control Groups support ARM: exynos_defconfig: Enable Atmel maXTouch support ARM: exynos_defconfig: Enable MAX77802
-
- 19 Oct, 2014 7 commits
-
-
git://git.infradead.org/users/eparis/auditLinus Torvalds authored
Pull audit updates from Eric Paris: "So this change across a whole bunch of arches really solves one basic problem. We want to audit when seccomp is killing a process. seccomp hooks in before the audit syscall entry code. audit_syscall_entry took as an argument the arch of the given syscall. Since the arch is part of what makes a syscall number meaningful it's an important part of the record, but it isn't available when seccomp shoots the syscall... For most arch's we have a better way to get the arch (syscall_get_arch) So the solution was two fold: Implement syscall_get_arch() everywhere there is audit which didn't have it. Use syscall_get_arch() in the seccomp audit code. Having syscall_get_arch() everywhere meant it was a useless flag on the stack and we could get rid of it for the typical syscall entry. The other changes inside the audit system aren't grand, fixed some records that had invalid spaces. Better locking around the task comm field. Removing some dead functions and structs. Make some things static. Really minor stuff" * git://git.infradead.org/users/eparis/audit: (31 commits) audit: rename audit_log_remove_rule to disambiguate for trees audit: cull redundancy in audit_rule_change audit: WARN if audit_rule_change called illegally audit: put rule existence check in canonical order next: openrisc: Fix build audit: get comm using lock to avoid race in string printing audit: remove open_arg() function that is never used audit: correct AUDIT_GET_FEATURE return message type audit: set nlmsg_len for multicast messages. audit: use union for audit_field values since they are mutually exclusive audit: invalid op= values for rules audit: use atomic_t to simplify audit_serial() kernel/audit.c: use ARRAY_SIZE instead of sizeof/sizeof[0] audit: reduce scope of audit_log_fcaps audit: reduce scope of audit_net_id audit: arm64: Remove the audit arch argument to audit_syscall_entry arm64: audit: Add audit hook in syscall_trace_enter/exit() audit: x86: drop arch from __audit_syscall_entry() interface sparc: implement is_32bit_task sparc: properly conditionalize use of TIF_32BIT ...
-
Olof Johansson authored
Merge tag 'qcom-dt-for-3.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into fixes Merge "qcom DT changes for v3.18-3" from Kumar Gala: Qualcomm ARM Based Device Tree Updates for v3.18-3 * Added Board support for CM-QS600 and Sony Xperia Z1 phone * Added SATA support on IPQ8064/AP148 * tag 'qcom-dt-for-3.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom: ARM: dts: qcom: add CM-QS600 board ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone ARM: dts: qcom: Add SATA support on IPQ8064/AP148
-
Olof Johansson authored
Merge tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes Pull more fixes from Kukjin Kim: 2nd Samsung fixes for v3.18 - Explicitly set dr_mode on exynos5800-peach-pi, exynos5420-peach-pit and exynos5420-arndale-octa boards, because the USB dwc3 controller will not work properly without dr_mode as host on above boards if the USB host and gadget are enabled in kernel configuration both. * tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa ARM: dts: Explicitly set dr_mode on exynos Peach boards Signed-off-by:
Olof Johansson <olof@lixom.net>
-
Scott Branden authored
Corrected bcm2835 maintainer info by using N: to specify any files with bcm2835 in are directed to the proper maintainer. Also corrected minor mispelling of ARCHITECTURE in 2 comment locations. Signed-off-by:
Scott Branden <sbranden@broadcom.com> Signed-off-by:
Stephen Warren <swarren@wwwdotorg.org> Signed-off-by:
-
git://github.com/jonmason/ntbLinus Torvalds authored
Pull ntb (non-transparent bridge) updates from Jon Mason: "Add support for Haswell NTB split BARs, a debugfs entry for basic debugging info, and some code clean-ups" * tag 'ntb-3.18' of git://github.com/jonmason/ntb: ntb: Adding split BAR support for Haswell platforms ntb: use errata flag set via DID to implement workaround ntb: conslidate reading of PPD to move platform detection earlier ntb: move platform detection to separate function NTB: debugfs device entry
-
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linuxLinus Torvalds authored
Pull i2c updates from Wolfram Sang: "Highlights from the I2C subsystem for 3.18: - new drivers for Axxia AM55xx, and Hisilicon hix5hd2 SoC. - designware driver gained AMD support, exynos gained exynos7 support The rest is usual driver stuff. Hopefully no lowlights this time" * 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: i801: Add Device IDs for Intel Sunrise Point PCH i2c: hix5hd2: add i2c controller driver i2c-imx: Disable the clock on probe failure i2c: designware: Add support for AMD I2C controller i2c: designware: Rework probe() to get clock a bit later i2c: designware: Default to fast mode in case of ACPI i2c: axxia: Add I2C driver for AXM55xx i2c: exynos: add support for HSI2C module on Exynos7 i2c: mxs: detect No Slave Ack on SELECT in PIO mode i2c: cros_ec: Remove EC_I2C_FLAG_10BIT i2c: cros-ec-tunnel: Add of match table i2c: rcar: remove sign-compare flaw i2c: ismt: Use minimum descriptor size i2c: imx: Add arbitration lost check i2c: rk3x: Remove unlikely() annotations i2c: rcar: check for no IRQ in rcar_i2c_irq() i2c: rcar: make rcar_i2c_prepare_msg() *void* i2c: rcar: simplify check for last message i2c: designware: add support of platform data to set I2C mode i2c: designware: add support of I2C standard mode
-
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/soundLinus Torvalds authored
Pull sound fixes from Takashi Iwai: "Here are a collection of small fixes after 3.18 merge. The urgent one is the fix for kernel panics with linked PCM substream triggered by the recent nonatomic PCM ops support. Other two fixes (emu10k1 and bebob) are stable fixes, and one easy PCI ID addition for a new Intel HD-audio controller" * tag 'sound-fix-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: ALSA: hda_intel: Add Device IDs for Intel Sunrise Point PCH ALSA: emu10k1: Fix deadlock in synth voice lookup ALSA: pcm: Fix referred substream in snd_pcm_action_group() unlock loop ALSA: bebob: Fix failure to detect source of clock for Terratec Phase 88
-
