Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.

// <smpl>
@@
expression ret;
struct platform_device *E;
@@

ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);

if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>

While we're here, remove braces on if statements that only have one
statement (manually).
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Mark switch cases where we are expecting to fall through.

This patch fixes the following warnings:

drivers/mfd/db8500-prcmu.c: In function 'dsiclk_rate':
drivers/mfd/db8500-prcmu.c:1592:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
   div *= 2;
   ~~~~^~~~
drivers/mfd/db8500-prcmu.c:1593:2: note: here
  case PRCM_DSI_PLLOUT_SEL_PHI_2:
  ^~~~
drivers/mfd/db8500-prcmu.c:1594:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
   div *= 2;
   ~~~~^~~~
drivers/mfd/db8500-prcmu.c:1595:2: note: here
  case PRCM_DSI_PLLOUT_SEL_PHI:
  ^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Intel Tiger Lake has the same LPSS than Intel Broxton.
Add the new IDs to the list of supported devices.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

It has been replaced with the ingenic-iio driver for the ADC.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Mark switch cases where we are expecting to fall through.

This patch fixes the following warnings:

drivers/mfd/omap-usb-host.c: In function 'usbhs_runtime_resume':
drivers/mfd/omap-usb-host.c:303:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
    if (!IS_ERR(omap->hsic480m_clk[i])) {
       ^
drivers/mfd/omap-usb-host.c:313:3: note: here
   case OMAP_EHCI_PORT_MODE_TLL:
   ^~~~
drivers/mfd/omap-usb-host.c: In function 'usbhs_runtime_suspend':
drivers/mfd/omap-usb-host.c:345:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
    if (!IS_ERR(omap->hsic480m_clk[i]))
       ^
drivers/mfd/omap-usb-host.c:349:3: note: here
   case OMAP_EHCI_PORT_MODE_TLL:
   ^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Goodix touchpad may drop its first couple input events when
i2c-designware-platdrv and intel-lpss it connects to took too long to
runtime resume from runtime suspended state.

This issue happens becuase the touchpad has a rather small buffer to
store up to 13 input events, so if the host doesn't read those events in
time (i.e. runtime resume takes too long), events are dropped from the
touchpad's buffer.

The bottleneck is D3cold delay it waits when transitioning from D3cold
to D0, hence remove the delay to make the resume faster. I've tested
some systems with intel-lpss and haven't seen any regression.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202683Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Move from i2c_new_dummy() to i2c_new_dummy_device(), so we now get an
ERRPTR which we use in error handling.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

All preparational patches have been applied, we can now remove the
include file for platform_data. Yiha!
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Move from i2c_new_dummy() to devm_i2c_new_dummy_device(). So, we now get
an ERRPTR which we use in error handling and we can skip removal of the
created devices.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Update cros_ec_commands.h to match the fingerprint MCU section in
the current ec_commands.h
Signed-off-by: Yicheng Li <yichengli@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The RN5T618 family of PMICs can be used as system management
controllers, in which case they handle poweroff and restart. Document
this capability by referring to the corresponding generic DT binding.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

When calling debugfs functions, there is no need to ever check the
return value.  The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

When calling debugfs functions, there is no need to ever check the
return value.  The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

When calling debugfs functions, there is no need to ever check the
return value.  The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

When building davinci as multiplatform, we get a build error
in this file:

drivers/mfd/davinci_voicecodec.c:22:10: fatal error: 'mach/hardware.h' file not found

The header is only used to access the io_v2p() macro, but the
result is already known because that comes from the resource
a little bit earlier.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Pull Devicetree fixes from Rob Herring:
 "Fix several warnings/errors in validation of binding schemas"

* tag 'devicetree-fixes-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  dt-bindings: pinctrl: stm32: Fix missing 'clocks' property in examples
  dt-bindings: iio: ad7124: Fix dtc warnings in example
  dt-bindings: iio: avia-hx711: Fix avdd-supply typo in example
  dt-bindings: pinctrl: aspeed: Fix AST2500 example errors
  dt-bindings: pinctrl: aspeed: Fix 'compatible' schema errors
  dt-bindings: riscv: Limit cpus schema to only check RiscV 'cpu' nodes
  dt-bindings: Ensure child nodes are of type 'object'

Pull vfs documentation typo fix from Al Viro.

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  typo fix: it's d_make_root, not d_make_inode...

Pull cifs fixes from Steve French:
 "Two fixes for stable, one that had dependency on earlier patch in this
  merge window and can now go in, and a perf improvement in SMB3 open"

* tag '5.3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update internal module number
  cifs: flush before set-info if we have writeable handles
  smb3: optimize open to not send query file internal info
  cifs: copy_file_range needs to strip setuid bits and update timestamps
  CIFS: fix deadlock in cached root handling

The commit b3aa14f0 ("iommu: remove the mapping_error dma_map_ops
method") incorrectly changed the checking from dma_ops_alloc_iova() in
map_sg() causes a crash under memory pressure as dma_ops_alloc_iova()
never return DMA_MAPPING_ERROR on failure but 0, so the error handling
is all wrong.

   kernel BUG at drivers/iommu/iova.c:801!
    Workqueue: kblockd blk_mq_run_work_fn
    RIP: 0010:iova_magazine_free_pfns+0x7d/0xc0
    Call Trace:
     free_cpu_cached_iovas+0xbd/0x150
     alloc_iova_fast+0x8c/0xba
     dma_ops_alloc_iova.isra.6+0x65/0xa0
     map_sg+0x8c/0x2a0
     scsi_dma_map+0xc6/0x160
     pqi_aio_submit_io+0x1f6/0x440 [smartpqi]
     pqi_scsi_queue_command+0x90c/0xdd0 [smartpqi]
     scsi_queue_rq+0x79c/0x1200
     blk_mq_dispatch_rq_list+0x4dc/0xb70
     blk_mq_sched_dispatch_requests+0x249/0x310
     __blk_mq_run_hw_queue+0x128/0x200
     blk_mq_run_work_fn+0x27/0x30
     process_one_work+0x522/0xa10
     worker_thread+0x63/0x5b0
     kthread+0x1d2/0x1f0
     ret_from_fork+0x22/0x40

Fixes: b3aa14f0 ("iommu: remove the mapping_error dma_map_ops method")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The hexagon implementation pte_alloc_one(), pte_alloc_one_kernel(),
pte_free_kernel() and pte_free() is identical to the generic except of
lack of __GFP_ACCOUNT for the user PTEs allocation.

Switch hexagon to use generic version of these functions.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull NTB updates from Jon Mason:
 "New feature to add support for NTB virtual MSI interrupts, the ability
  to test and use this feature in the NTB transport layer.

  Also, bug fixes for the AMD and Switchtec drivers, as well as some
  general patches"

* tag 'ntb-5.3' of git://github.com/jonmason/ntb: (22 commits)
  NTB: Describe the ntb_msi_test client in the documentation.
  NTB: Add MSI interrupt support to ntb_transport
  NTB: Add ntb_msi_test support to ntb_test
  NTB: Introduce NTB MSI Test Client
  NTB: Introduce MSI library
  NTB: Rename ntb.c to support multiple source files in the module
  NTB: Introduce functions to calculate multi-port resource index
  NTB: Introduce helper functions to calculate logical port number
  PCI/switchtec: Add module parameter to request more interrupts
  PCI/MSI: Support allocating virtual MSI interrupts
  ntb_hw_switchtec: Fix setup MW with failure bug
  ntb_hw_switchtec: Skip unnecessary re-setup of shared memory window for crosslink case
  ntb_hw_switchtec: Remove redundant steps of switchtec_ntb_reinit_peer() function
  NTB: correct ntb_dev_ops and ntb_dev comment typos
  NTB: amd: Silence shift wrapping warning in amd_ntb_db_vector_mask()
  ntb_hw_switchtec: potential shift wrapping bug in switchtec_ntb_init_sndev()
  NTB: ntb_transport: Ensure qp->tx_mw_dma_addr is initaliazed
  NTB: ntb_hw_amd: set peer limit register
  NTB: ntb_perf: Clear stale values in doorbell and command SPAD register
  NTB: ntb_perf: Disable NTB link after clearing peer XLAT registers
  ...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Now that examples are validated against the DT schema, an error with
required 'clocks' property missing is exposed:

Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@40020000: gpio@0: 'clocks' is a required property
Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@50020000: gpio@1000: 'clocks' is a required property
Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@50020000: gpio@2000: 'clocks' is a required property

Add the missing 'clocks' properties to the examples to fix the errors.

Fixes: 2c9239c1 ("dt-bindings: pinctrl: Convert stm32 pinctrl bindings to json-schema")
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>