ext3 has fancy test harness code which allows you to simulate crashes (for
testing recovery).  It will make the underlying disk start ignoring writes a
specified number of seconds after the mount.

It's inoperative without an additional offline patch anyway, and it's doing
hacky things which scared Al.  So kill it; I'll maintain it in the separate
ext3 debug patch.

From: Andre McCurdy <armcc2000@yahoo.com>

There is some inconsistency within lib/inflate.c and its users about
whether the error message text or the error() function should provide
the '\n'.

This patch tries to make everyone consistent - by removing the
newline from all message texts, and adding one to the only error()
function which did not provide it (in init/do_mounts_rd.c).

From: Andrey Borzenkov <arvidjaar@mail.ru>

LANG is not always enough to force date to english.

From: Rajesh Venkatasubramanian <vrajesh@eecs.umich.edu>

Don't deref the pte pointer after having kunmapped the memory it points at.

From: Rajesh Venkatasubramanian <vrajesh@eecs.umich.edu>

The remap_file_pages system call with MAP_NONBLOCK flag does not
install file-ptes when the required pages are not found in the
page cache. Modify the populate functions to install file-ptes
if the mapping is non-linear and the required pages are not found
in the page cache.

Patch is for test4-mm6. Compiles and boots. Patch tested using the
programs at:

http://www-personal.engin.umich.edu/~vrajesh/linux/remap-file-pages/

From: "Nakajima, Jun" <jun.nakajima@intel.com>

Attached is a patch that enables PNI (Prescott New Instructions)
monitor/mwait in the kernel idle handler.

From: Maneesh Soni <maneesh@in.ibm.com>

d_delete() calls dentry_iput() after releasing the per dentry lock.  This
can race with __d_lookup and lead to situation where we can make dentry
negative with ref count > 1.  The following patch makes dentry_iput() to
hold per dentry lock till d_inode is NULL and dentry has been removed from
d_alias list.

From: Christoph Hellwig <hch@infradead.org>

PPP leaves the chardev registered even if we're going to fail the modprobe.

From: john stultz <johnstul@us.ibm.com>

Don't try to support more than NR_CPUS cpus: things overflow.

Also, increase the default in config for some architectures.  (Dave
Hansen).

From: "Randy.Dunlap" <rddunlap@osdl.org>

remove duplicate #includes in kernel/

From: "Randy.Dunlap" <rddunlap@osdl.org>

remove duplicate #includes in sound/

From: James Morris <jmorris@redhat.com>

This patch against current bk makes the recently added SELinux boot
parameter feature a configurable option, and enables SELinux by default
when selected.  These changes were made following feedback including 
discussion on the SELinux list.

The rationale for the changes is to allow SELinux to be be configured and
enabled unconditionally.  If the boot parameter option is selected, then
SELinux is now enabled unless selinux=0 is specified at the kernel command
line.

From: Adrian Bunk <bunk@fs.tum.de>

Earlier patch wasn't correct especially in the !CONFIG_SCSI_IZIP_EPP16
case, reading all uses of this array (IMM_MODE_STRING is used to print the
corresponding string in printks).

If I'm not misunderstanding it, CONFIG_SCSI_IZIP_EPP16 means "use 16bit 
even when 32bit is requested".

It seems the right solution is

static char *IMM_MODE_STRING[] =
{
        [IMM_AUTODETECT] = "Autodetect",
        [IMM_NIBBLE]     = "SPP",
        [IMM_PS2]        = "PS/2",
        [IMM_EPP_8]      = "EPP 8 bit",
        [IMM_EPP_16]     = "EPP 16 bit",
#ifdef CONFIG_SCSI_IZIP_EPP16
        [IMM_EPP_32]     = "EPP 16 bit",
#else
        [IMM_EPP_32]     = "EPP 32 bit",
#endif
        [IMM_UNKNOWN]    = "Unknown",
};

From: Oleg Drokin <green@namesys.com>

This patch implements DirectIO support for reiserfs v3.  This is mostly a
port from 2.4.

Thanks to Mingming Cao from IBM for some clues in porting.

From: "Randy.Dunlap" <randy.dunlap@verizon.net>


The SuSE kernels place their ikconfig info at /proc/config.gz: in a
different place, and compressed.  We thought it was a good idea to do it
that way in 2.6 as well.

- gzip the /proc config file, put it in /proc/config.gz;

- Based on a SuSE patch by Oliver Xymoron <oxymoron@waste.org>, which was
  derived from a patch by Nicholas Leon <nicholas@binary9.net>

- change /proc/ikconfig/built_with to /proc/config_build_info;

- cleanup ikconfig init/exit entry points (static, __init, __exit);

- Makefile help from Sam Ravnborg;

DESC
ikconfig cleanup
EDESC
From: Stephen Hemminger <shemminger@osdl.org>

Simplify and cleanup the code:
	- use single interface to seq_file where possible
	- don't need to do as much of the /proc interface, only read
	- use copy_to_user to avoid char at a time copy
	- remove unneccesary globals
	- use const char[] rather than const char * where possible.

Didn't change the version since interface doesn't change.

From: Dave Olien <dmo@osdl.org>

This patch is forwarded from Jay Estabrook at HP.  I've compiled the
patch on ia32 and ia64 machines and it's good.  I also recreated
the patch so it would apply to mm5 without fuzzy offsets.
Here's Jay's summary of the patch:

Here's a very small set of patches against 2.6.0-test4 that help the
DAC960 driver compile cleaner (gets rid of warnings on Alpha) and help
it to work on some old OEM'ed DAC960 cards that were sold in our older
Alphas.

The warnings are all concerned with "conversions to different size
without cast", as pointers and longs are same size (8-bytes) but ints
are 4-bytes, on Alpha. I don't believe the change to (long) from (int)
will affect any 32-bit architectures, but those using LP64 like Alpha,
ie SPARC64 and prolly IA64, will have the warnings go away.

The change to make the oldest acceptable firmware version 2.70 instead
of 2.73 is made spcific to Alpha, since it is only those cards that
DEC OEM'ed from Mylex that would have such (as explained a bit better
in the patch itself).

From: Andrey Borzenkov <arvidjaar@mail.ru>

DAC960.c does it incorrectly (at least in 2.6.0-test4). It will create
_directory_ /dev/rd/cNdM making it impossible to create compat block device
entry with the same name.

The right thing it to create separate directory for each controller/target as 
in attached trivial patch (untested due to lack of hardware). You will need
devfsd support for this but then you will need it for cciss or cpqarray as 
well and possibly for others. Which returns us to the problem of devfsd 
maintenance ...

From: Dmitry Torokhov <dtor_core@ameritech.net>

I noticed that although timer_tsc registers cpufreq notifier to detect
frequency changes and adjust cpu_khz it does not set cyc2ns_scale.

From: Andrey Borzenkov <arvidjaar@mail.ru>

Various block drivers are currently devfs-unaware.  Andrey's patch attempts
to give them reasonable representations in devfs.


 "The attached patch suggests some possible names for non-floppy devices
  based on reading driver source.  I have to ask if these make sense.  At
  least for cciss Mandrake devfsd patch expects different names but it
  seems to be mistake (it assumes single controller always)

 "For floppy it is not as simple.  Floppy cannot use genhd and must
  create names manually; but I do not know what names are appropriate or
  expected.

 "For acsi the target/lun name may have problem of creating compat names
  (if any) by devfsd.

 "Please note that none of them created any devfs name under 2.4 as well.
   So it is not a regression ..."

From: "Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>

CONFIG_TIMER_CYCLONE doesn't build at present because calibrate_tsc() was
made static.

The patch fixes that up and moves all calibrate_tsc functions into a common
file, avoiding the current code duplication.

From: Vinay K Nallamothu <vinay-rc@naturesoft.net>

Fix a couple of cut-n-paste errors.

(Why on earth is a scsi driver poking at the RTC hardware?)

Damn 16-bit PCMCIA layer has no type checking. Complete crap.

to a pointer. That was a typo.

Ack'ed by Al Viro.

Fix the ## handling to work with old gcc versions (spaces around the ','
to make token boundaries work).

Convert SIEMENS R3964 tty line discipline on 2.6.0-test5 to use tty_ldisc owner
instead of explicit MOD_INC/DEC.

And fix the initializer to be a much more readable C99 one.

There is a leftover MOD_DEC_USE_COUNT intermezzo, with no matching _INC_
anywhere.

Since it sets owner on the file system operations there should be no
need for explicit module manipulation.

into home.osdl.org:/home/torvalds/v2.5/linux

Add a new cpufreq_update_policy call:

Certain cpufreq policy notifers have different needs at different times.
Thus it needs to be possible to re-evaluate an already set cpufreq policy.
Note that the cpufreq policy should only be set by one person: the user.
Not any other in-kernel code [with one exception, of course: during
booting].

From: Hiroshi Miura <miura@da-cha.org>

Intel SpeedStep driver using a BIOS SMI call.

Quoting his original announcement:

"This driver is based on the information from

1. Microsoft Windows XP Document.
we can get the SMI interface values from ax=E980/int15 BIOS call.

2. Intel SpeedStep Applet Document.(from HP.com)
http://h18007.www1.hp.com/support/files/evonotebook/us/download/10631.html
" Adds code to request transition ownership when processing
the system critical resume message. When a critical hibernate occurs,
the Applet does not receive any system level notification. The change forces
the Applet to re-acquire transition ownership upon resume from a critical hibernate. "

This is informative. This saied that  something 'ownership' call is needed on SMI
interface first.

3. Grover, Andrew's int 15h patch posted to cpufreq ml
Message-ID: <F760B14C9561B941B89469F59BA3A847E96E28@orsmsx401.jf.intel.com>
code which call BIOS to get SMI values. I included it.

4. Malik Martin's rev engineering results.
call is made with BX, CX, EDI register values.
and need signature 'ISG' when call.
find function values. bx=1(get) and bx=2(set)

5. Marc Lehmann's 'speedstep' utility,
sample of assembler code to call SMI.

6. My work.
find function to return max/min freq which system supportd. (bx=4)
more values are gotten, but I cannot understand...
find 'ownership' function value(bx=0, which is other than 1 2 4..).

ToDo(in pregress)
support governor "auto" and using smi_event call, imprement auto freqchange
feature.
test on 440BX/ZX platform.

Memo
 module parameters are override result of an int 15h/eax=E890h call.
 these parameter value are gotten from Windows XP registory."

Also includes some bugfixes, updates and workarounds from me.

NB: A lot of BIOS out there are buggy. You might want to try this driver
also with Intel's default values -- smi_cmd = 0x82 and smi_port = 0xb2

into home.osdl.org:/home/torvalds/v2.5/linux

into samba.org:/scratch/anton/tmp3

cpumask_up.h is broken. It tries to access the "mask" member although
that cpumask_t is an ulong on UP. This breaks archs which uses cpumask
functions even on UP such as s390.

We only support named initializers with one leval of naming, ie that

	.foo.bar = baz,

thing should go.  gcc-2.95 doesn't handle it (neither does sparse, I
think).

Replace such initializers with

	.foo = {
		.bar = baz,
	},

instead.