...as advertised for 3.10.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Signed-off-by: Steve French <smfrench@gmail.com>

Pull MMC update from Chris Ball:
 "MMC highlights for 3.10:

  Core:
   - Introduce MMC_CAP2_NO_PRESCAN_POWERUP to allow skipping
     mmc_power_up() at boot/initialization time if it's already
     happened, for performance (faster boot time) reasons.
   - Fix a bit width test failure that resulted in old eMMC cards being
     put into 1-bit mode when 4-bit mode was available.
   - Expose fwrev/hwrev for MMCv4 parts.
   - Improve card removal logic in the case where the card's removed
     slowly; we were missing card removal events if the card retained
     contact with the slot pads for long enough to reply to a CMD13
     while being removed.

  Drivers:
   - davinci_mmc: Support using PIO instead of DMA.
   - dw_mmc: Add support for Exynos4412.
   - mxcmmc: DT support, use slot-gpio API.
   - mxs-mmc: Add broken-cd/cd-inverted/non-removable DT property
     support.
   - sdhci-sirf: New sdhci-pltfm driver for CSR SiRF SoCs:
       SiRFprimaII: unicore ARM Cortex-A9
       SiRFatlas6: unicore ARM Cortex-A9
       SiRFmarco: dual core ARM Cortex-A9 SMP
   - sdhci-tegra: Add support for Tegra114 platforms, use
     mmc_of_parse()"

* tag 'mmc-updates-for-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (66 commits)
  mmc: sdhci-tegra: fix MODULE_DEVICE_TABLE
  mmc: core: fix init controller performance regression, updated patch
  mmc: mxcmmc: enable DMA support on mpc512x
  mmc: mxcmmc: constify mxcmci_devtype
  mmc: mxcmmc: use slot-gpio API for write-protect detection
  mmc: mxcmmc: add mpc512x SDHC support
  mmc: mxcmmc: fix race conditions for host->req and host->data access
  mmc: mxcmmc: DT support
  mmc: dw_mmc: let device core setup the default pin configuration
  mmc: mxs-mmc: add broken-cd property
  mmc: mxs-mmc: add non-removable property
  mmc: mxs-mmc: add cd-inverted property
  mmc: core: call pm_runtime_put_noidle in pm_runtime_get_sync failed case
  mmc: mxcmmc: Fix bug when card is present during boot
  mmc: core: fix performance regression initializing MMC host controllers
  Revert "mmc: core: wait while adding MMC host to ensure root mounts successfully"
  mmc: atmel-mci: pio hang on block errors
  mmc: core: Fix bit width test failing on old eMMC cards
  mmc: dw_mmc: Use pr_info instead of printk
  mmc: dw_mmc: Check return value of regulator_enable
  ...

Pull hwmon update from Jean Delvare:
 "Only lm75 driver updates this time"

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (lm75) Add support for the Dallas/Maxim DS7505
  hwmon: (lm75) Tune resolution and sample time per chip
  hwmon: (lm75) Prepare to support per-chip resolution and sample time
  hwmon: (lm75) Per-chip configuration register initialization

Pull second round of VFS updates from Al Viro:
 "Assorted fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  xtensa simdisk: fix braino in "xtensa simdisk: switch to proc_create_data()"
  hostfs: use kmalloc instead of kzalloc
  hostfs: move HOSTFS_SUPER_MAGIC to <linux/magic.h>
  hostfs: remove "will unlock" comment
  vfs: use list_move instead of list_del/list_add
  proc_devtree: Replace include linux/module.h with linux/export.h
  create_mnt_ns: unidiomatic use of list_add()
  fs: remove dentry_lru_prune()
  Removed unused typedef to avoid "unused local typedef" warnings.
  kill fs/read_write.h
  fs: Fix hang with BSD accounting on frozen filesystem
  sun3_scsi: add ->show_info()
  nubus: Kill nubus_proc_detach_device()
  more mode_t whack-a-mole...
  do_coredump(): don't wait for thaw if coredump has already been interrupted
  do_mount(): fix a leak introduced in 3.9 ("mount: consolidate permission checks")

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

The inode info structure is zeroed at allocation with kzalloc, and then
all but one of the fields (including the largest, vfs_inode) are
initialised explicitly. Switch to using kmalloc and initialise the
remaining field too.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Move HOSTFS_SUPER_MAGIC to <linux/magic.h> to be with it's magical
friends from other file systems.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

A "will unlock" comment was added to hostfs in the following commit,
along with a spinlock:

Commit e9193059 ("hostfs: fix races in
dentry_name() and inode_name()").

But the spinlock was subsequently removed in the following commit:

Commit ec2447c2 ("hostfs: simplify
locking").

Since the comment is no longer applicable, remove it.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Using list_move() instead of list_del() + list_add().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull ARM SoC board specific changes (part 1) from Olof Johansson:
 "These changes are all for board specific files.  These used to make up
  a large portion of the ARM changes in the past, but as we are
  generalizing the support and moving to device tree probing, this has
  gotten significantly smaller.

  The only platform actually adding new code here at the moment is
  Renesas shmobile, as they are still busy converting their code to
  device tree and have not come far enough to not need it."

* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
  ARM: msm: USB_MSM_OTG needs USB_PHY
  ARM: davinci: da850 evm: fix const qualifier placement
  ARM: davinci: da850 board: add remoteproc support
  ARM: pxa: move debug uart code
  ARM: pxa: select PXA935 on saar & tavorevb
  ARM: mmp: add more compatible names in gpio driver
  ARM: pxa: move PXA_GPIO_TO_IRQ macro
  ARM: pxa: remove cpu_is_xxx in gpio driver
  ARM: Kirkwood: update Network Space Mini v2 description
  ARM: Kirkwood: DT board setup for CloudBox
  ARM: Kirkwood: sort board entries by ASCII-code order
  ARM: OMAP: board-4430sdp: Provide regulator to pwm-backlight
  ARM: OMAP: zoom: Use pwm stack for lcd and keyboard backlight
  ARM: OMAP2+: omap2plus_defconfig: Add support for BMP085 pressure sensor
  omap2+: Remove useless Makefile line
  omap2+: Remove useless Makefile line
  ARM: OMAP: RX-51: add missing regulator supply definitions for lis3lv02d
  ARM: OMAP1: fix omap_udc registration
  ARM: davinci: use is IS_ENABLED macro
  ARM: kirkwood: add MACH_GURUPLUG_DT to defconfig
  ...

Pull ARM platform specific firmware interfaces from Olof Johansson:
 "Two platforms, bcm and exynos have their own firmware interfaces using
  the "secure monitor call", this adds support for those.

  We had originally planned to have a third set of patches in here,
  which would extend support for the existing generic "psci" call that
  is used on multiple platforms as well as Xen and KVM guests, but that
  ended up getting dropped because the patches were not ready in time."

* tag 'firmware-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: bcm: mark bcm_kona_smc_init as __init
  ARM: bcm281xx: Add DT support for SMC handler
  ARM: bcm281xx: Add L2 cache enable code
  ARM: EXYNOS: Add secure firmware support to secondary CPU bring-up
  ARM: EXYNOS: Add IO mapping for non-secure SYSRAM.
  ARM: EXYNOS: Add support for Exynos secure firmware
  ARM: EXYNOS: Add support for secure monitor calls
  ARM: Add interface for registering and calling firmware-specific operations

Pull ARM SoC pinctrl changes for Renesas from Olof Johansson:
 "This is yet another driver change, which is split out just because of
  its size.  As already in 3.9, a lot of changes are going on here, as
  the shmobile platform gets converted from its own pin control API to
  the generic drivers/pinctrl subsystem.

  Based on agreements with Paul Mundt, we are merging the sh-arch-side
  changes here as well"

* tag 'renesas-pinctrl-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (142 commits)
  ARM: shmobile: r8a7779: Remove INTC function GPIOs
  ARM: shmobile: r8a7779: Remove LBSC function GPIOs
  ARM: shmobile: r8a7779: Remove USB function GPIOs
  ARM: shmobile: r8a7779: Remove HSPI function GPIOs
  ARM: shmobile: r8a7779: Remove SCIF function GPIOs
  ARM: shmobile: r8a7779: Remove SDHI and MMCIF function GPIOs
  ARM: shmobile: r8a7779: Remove DU function GPIOs
  ARM: shmobile: r8a7779: Remove DU1_DOTCLKOUT1 GPIO
  ARM: shmobile: r8a7740: Remove SDHI and MMCIF function GPIOs
  ARM: shmobile: r8a7740: Remove LCD0 and LCD1 function GPIOs
  ARM: shmobile: sh73a0: Remove IrDA function GPIOs
  ARM: shmobile: sh73a0: Remove USB function GPIOs
  ARM: shmobile: sh73a0: Remove BSC function GPIOs
  ARM: shmobile: sh73a0: Remove KEYSC function GPIOs
  ARM: shmobile: sh73a0: Remove pull-up function GPIOS
  ARM: shmobile: sh73a0: Remove FSI function GPIOs
  ARM: shmobile: sh73a0: Remove I2C function GPIOs
  ARM: shmobile: sh73a0: Remove SCIFA and SCIFB function GPIOs
  ARM: shmobile: sh73a0: Remove LCDC and LCDC2 function GPIOs
  ARM: shmobile: sh7372: Remove SDHI and MMCIF function GPIOs
  ...

Pull ARM SoC driver changes from Olof Johansson:
 "This is a rather large set of patches for device drivers that for one
  reason or another the subsystem maintainer preferred to get merged
  through the arm-soc tree.  There are both new drivers as well as
  existing drivers that are getting converted from platform-specific
  code into standalone drivers using the appropriate subsystem specific
  interfaces.

  In particular, we can now have pinctrl, clk, clksource and irqchip
  drivers in one file per driver, without the need to call into platform
  specific interface, or to get called from platform specific code, as
  long as all information about the hardware is provided through a
  device tree.

  Most of the drivers we touch this time are for clocksource.  Since now
  most of them are part of drivers/clocksource, I expect that we won't
  have to touch these again from arm-soc and can let the clocksource
  maintainers take care of these in the future.

  Another larger part of this series is specific to the exynos platform,
  which is seeing some significant effort in upstreaming and
  modernization of its device drivers this time around, which
  unfortunately is also the cause for the churn and a lot of the merge
  conflicts.

  There is one new subsystem that gets merged as part of this series:
  the reset controller interface, which is a very simple interface for
  taking devices on the SoC out of reset or back into reset.  Patches to
  use this interface on i.MX follow later in this merge window, and we
  are going to have other platforms (at least tegra and sirf) get
  converted in 3.11.  This will let us get rid of platform specific
  callbacks in a number of platform independent device drivers."

* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (256 commits)
  irqchip: s3c24xx: add missing __init annotations
  ARM: dts: Disable the RTC by default on exynos5
  clk: exynos5250: Fix parent clock for sclk_mmc{0,1,2,3}
  ARM: exynos: restore mach/regs-clock.h for exynos5
  clocksource: exynos_mct: fix build error on non-DT
  pinctrl: vt8500: wmt: Fix checking return value of pinctrl_register()
  irqchip: vt8500: Convert arch-vt8500 to new irqchip infrastructure
  reset: NULL deref on allocation failure
  reset: Add reset controller API
  dt: describe base reset signal binding
  ARM: EXYNOS: Add arm-pmu DT binding for exynos421x
  ARM: EXYNOS: Add arm-pmu DT binding for exynos5250
  ARM: EXYNOS: Enable PMUs for exynos4
  irqchip: exynos-combiner: Correct combined IRQs for exynos4
  irqchip: exynos-combiner: Add set_irq_affinity function for combiner_irq
  ARM: EXYNOS: fix compilation error introduced due to common clock migration
  clk: exynos5250: Fix divider values for sclk_mmc{0,1,2,3}
  clk: exynos4: export clocks required for fimc-is
  clk: samsung: Fix compilation error
  clk: tegra: fix enum tegra114_clk to match binding
  ...

Since it uses only THIS_MODULE macro, include <linux/export.h>
is the right to go here.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

while list_add(A, B) and list_add(B, A) are equivalent when both A and B
are guaranteed to be empty, the usual idiom is list_add(what, where),
not the other way round...  Not a bug per se, but only by accident and
it makes RTFS harder for no good reason.
Spotted-by: Rajat Sharma <fs.rajat@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

When pruning a dentry, its ancestor dentry can also be pruned. But
the ancestor dentry does not go through dput(), so it does not get
put on the dentry LRU. Hence associating d_prune with removing the
dentry from the LRU is the wrong.

The fix is remove dentry_lru_prune(). Call file system's d_prune()
callback directly when pruning dentries.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Fix warnings about unused local typedefs (reported by gcc 4.8).

Signed-off-by: Han Shen  (shenhan@google.com)

Change-Id: I4bccc234f1390daa808d2b309ed112e20c0ac096
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

fs/compat.c doesn't need it anymore, so let's just move the remaining
contents (two typedefs) into fs/read_write.c
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

When BSD process accounting is enabled and logs information to a
filesystem which gets frozen, system easily becomes unusable because
each attempt to account process information blocks. Thus e.g. every task
gets blocked in exit.

It seems better to drop accounting information (which can already happen
when filesystem is running out of space) instead of locking system up.
So we just skip the write if the filesystem is frozen.
Reported-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Based on Al's changes to atari_scsi.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Commit 59d8053f ("proc: Move non-public
stuff from linux/proc_fs.h to fs/proc/internal.h") broke Apple NuBus
support:

drivers/nubus/proc.c: In function ‘nubus_proc_detach_device’:
drivers/nubus/proc.c:156: error: dereferencing pointer to incomplete type
drivers/nubus/proc.c:158: error: dereferencing pointer to incomplete type

Fortunately nubus_proc_detach_device() is unused, and appears to have never
been used, so just remove it.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Cc: stable@vger.kernel.org
Bisected-by: Michael Leun <lkml20130126@newton.leun.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Basically it's the same as the original DS75 but much faster.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>

Most LM75-compatible chips can either sample much faster or with a
much better resolution than the original LM75 chip. So far the lm75
driver did not let the user take benefit of these improvements. Do it
now.

I decided to almost always configure the chip to use the best
resolution possible, which also means the longest sample time. The
only chips for which I didn't are the DS75, DS1775 and STDS75, because
they are really too slow in 12-bit mode (1.2 to 1.5 second worst case)
so I went for 11-bit mode as a more reasonable tradeoff. This choice is
dictated by the fact that the hwmon subsystem is meant for system
monitoring, it has never been supposed to be ultra-fast, and as a
matter of fact we do cache the sampled values in almost all drivers.

If anyone isn't pleased with these default settings, they can always
introduce a platform data structure or DT support for the lm75. That
being said, it seems nobody ever complained that the driver wouldn't
refresh the value faster than every 1.5 second, and the change made
it faster for all chips even in 12-bit mode, so I don't expect any
complaint.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>

Prepare the lm75 driver to support per-chip resolution and sample
time. For now we only make the code generic enough to support it, but
we still use the same, unchanged resolution (9-bit) and sample time
(1.5 s) for all chips.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>

There is no standard for the configuration register bits of LM75-like
chips. We shouldn't blindly clear bits setting the resolution as they
are either unused or used for something else on some of the supported
chips.

So, switch to per-chip configuration initialization. This will allow
for better tuning later, for example using more resolution bits when
available.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>

Pull nfsd changes from J Bruce Fields:
 "Highlights include:

   - Some more DRC cleanup and performance work from Jeff Layton

   - A gss-proxy upcall from Simo Sorce: currently krb5 mounts to the
     server using credentials from Active Directory often fail due to
     limitations of the svcgssd upcall interface.  This replacement
     lifts those limitations.  The existing upcall is still supported
     for backwards compatibility.

   - More NFSv4.1 support: at this point, if a user with a current
     client who upgrades from 4.0 to 4.1 should see no regressions.  In
     theory we do everything a 4.1 server is required to do.  Patches
     for a couple minor exceptions are ready for 3.11, and with those
     and some more testing I'd like to turn 4.1 on by default in 3.11."

Fix up semantic conflict as per Stephen Rothwell and linux-next:

Commit 030d794b ("SUNRPC: Use gssproxy upcall for server RPCGSS
authentication") adds two new users of "PDE(inode)->data", but we're
supposed to use "PDE_DATA(inode)" instead since commit d9dda78b
("procfs: new helper - PDE_DATA(inode)").

The old PDE() macro is no longer available since commit c30480b9
("proc: Make the PROC_I() and PDE() macros internal to procfs")

* 'for-3.10' of git://linux-nfs.org/~bfields/linux: (60 commits)
  NFSD: SECINFO doesn't handle unsupported pseudoflavors correctly
  NFSD: Simplify GSS flavor encoding in nfsd4_do_encode_secinfo()
  nfsd: make symbol nfsd_reply_cache_shrinker static
  svcauth_gss: fix error return code in rsc_parse()
  nfsd4: don't remap EISDIR errors in rename
  svcrpc: fix gss-proxy to respect user namespaces
  SUNRPC: gssp_procedures[] can be static
  SUNRPC: define {create,destroy}_use_gss_proxy_proc_entry in !PROC case
  nfsd4: better error return to indicate SSV non-support
  nfsd: fix EXDEV checking in rename
  SUNRPC: Use gssproxy upcall for server RPCGSS authentication.
  SUNRPC: Add RPC based upcall mechanism for RPCGSS auth
  SUNRPC: conditionally return endtime from import_sec_context
  SUNRPC: allow disabling idle timeout
  SUNRPC: attempt AF_LOCAL connect on setup
  nfsd: Decode and send 64bit time values
  nfsd4: put_client_renew_locked can be static
  nfsd4: remove unused macro
  nfsd4: remove some useless code
  nfsd4: implement SEQ4_STATUS_RECALLABLE_STATE_REVOKED
  ...

Pull jfs fixes from David Kleikamp:
 "A couple fixes for jfs"

(What's with the unhelpful pull request "explanations" from fs people
today?)

* tag 'jfs-3.10' of git://github.com/kleikamp/linux-shaggy:
  jfs: fix a couple races
  jfs: avoid undefined behavior from left-shifting by 32 bits

Pull ext3/jbd fixes from Jan Kara:
 "A couple of ext3/jbd fixes"

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  jbd: use kmem_cache_zalloc for allocating journal head
  jbd: use kmem_cache_zalloc instead of kmem_cache_alloc/memset
  jbd: don't wait (forever) for stale tid caused by wraparound
  ext3: fix data=journal fast mount/umount hang

Pull ARM updates from Russell King:
 "The major items included in here are:

   - MCPM, multi-cluster power management, part of the infrastructure
     required for ARMs big.LITTLE support.

   - A rework of the ARM KVM code to allow re-use by ARM64.

   - Error handling cleanups of the IS_ERR_OR_NULL() madness and fixes
     of that stuff for arch/arm

   - Preparatory patches for Cortex-M3 support from Uwe Kleine-König.

  There is also a set of three patches in here from Hugh/Catalin to
  address freeing of inappropriate page tables on LPAE.  You already
  have these from akpm, but they were already part of my tree at the
  time he sent them, so unfortunately they'll end up with duplicate
  commits"

* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (77 commits)
  ARM: EXYNOS: remove unnecessary use of IS_ERR_VALUE()
  ARM: IMX: remove unnecessary use of IS_ERR_VALUE()
  ARM: OMAP: use consistent error checking
  ARM: cleanup: OMAP hwmod error checking
  ARM: 7709/1: mcpm: Add explicit AFLAGS to support v6/v7 multiplatform kernels
  ARM: 7700/2: Make cpu_init() notrace
  ARM: 7702/1: Set the page table freeing ceiling to TASK_SIZE
  ARM: 7701/1: mm: Allow arch code to control the user page table ceiling
  ARM: 7703/1: Disable preemption in broadcast_tlb*_a15_erratum()
  ARM: mcpm: provide an interface to set the SMP ops at run time
  ARM: mcpm: generic SMP secondary bringup and hotplug support
  ARM: mcpm_head.S: vlock-based first man election
  ARM: mcpm: Add baremetal voting mutexes
  ARM: mcpm: introduce helpers for platform coherency exit/setup
  ARM: mcpm: introduce the CPU/cluster power API
  ARM: multi-cluster PM: secondary kernel entry code
  ARM: cacheflush: add synchronization helpers for mixed cache state accesses
  ARM: cpu hotplug: remove majority of cache flushing from platforms
  ARM: smp: flush L1 cache in cpu_die()
  ARM: tegra: remove tegra specific cpu_disable()
  ...

Pull sound updates from Takashi Iwai:
 "Mostly many small changes spread as seen in diffstat in sound/*
  directory by this update.  A significant change in the subsystem level
  is the introduction of snd_soc_component, which will help more generic
  handling of SoC and off-SoC components.

  Also, snd_BUG_ON() macro is enabled unconditionally now due to its
  misuses, so people might hit kernel warnings (it's a good thing for
  us).

   - compress-offload: support for capture by Charles Keepax
   - HD-audio: codec delay support by Dylan Reid
   - HD-audio: improvements/fixes in generic parser: better headphone
     mic and headset mic support, jack_modes hint consolidation, proper
     beep attach/detachment, generalized power filter controls by David
     Henningsson, et al
   - HD-audio: Improved management of HDMI codec pins/converters
   - HD-audio: Better pin/DAC assignment for VIA codecs
   - HD-audio: Haswell HDMI workarounds
   - HD-audio: ALC268 codec support, a few new quirks for Chromebooks
   - USB: regression fixes: USB-MIDI autopm fix, the recent ISO latency
     fix by Clemens Ladisch
   - USB: support for DSD formats by Daniel Mack
   - USB: A few UAC2 device endian/cock fixes by Eldad Zack
   - USB: quirks for Emu 192kHz support, Novation Twitch DJ controller,
     Yamaha THRxx devices
   - HDSPM: updates for TCO controls by Adrian Knoth
   - ASoC: Add a snd_soc_component object type for generic handling of
     SoC and off-SoC components by Kuninori Morimoto,
   - dmaengine: a large set of cleanups and conversions by Lars-Peter
     Clausen
   - ASoC DAPM: performance optimizations from Ryo Tsutsui
   - ASoC DAPM: support for mixer control sharing by Stephen Warren
   - ASoC: multiplatform ARM cleanups from Arnd Bergmann
   - ASoC: new codec drivers for AK5385 and TAS5086 from Daniel Mack"

* tag 'sound-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (315 commits)
  ALSA: usb-audio: caiaq: fix endianness bug in snd_usb_caiaq_maschine_dispatch
  ALSA: asihpi: add format support check in snd_card_asihpi_capture_formats
  ALSA: pcm_format_to_bits strong-typed conversion
  ALSA: compress: fix the states to check for allowing read
  ALSA: hda - Move Thinkpad X220 to use auto parser
  ALSA: USB: adjust for changed 3.8 USB API
  ALSA: usb - Avoid unnecessary sample rate changes on USB 2.0 clock sources
  sound: oss/dmabuf: use dma_map_single
  ALSA: ali5451: use mdelay instead of large udelay constants
  ALSA: hda - Add the support for ALC286 codec
  ALSA: usb-audio: USB quirk for Yamaha THR10C
  ALSA: usb-audio: USB quirk for Yamaha THR5A
  ALSA: usb-audio: USB quirk for Yamaha THR10
  ALSA: usb-audio: Fix autopm error during probing
  ALSA: snd-usb: try harder to find USB_DT_CS_ENDPOINT
  ALSA: sound kconfig typo
  ALSA: emu10k1: Fix dock firmware loading
  ASoC: ux500: forward declare msp_i2s_platform_data
  ASoC: davinci-mcasp: Add Support BCLK-to-LRCLK ratio for TDM modes
  ASoC: davinci-pcm, davinci-mcasp: Clean up active_serializers
  ...

Pull pstore update from Anton Vorontsov:

 - A new platform data parameter to specify ECC configuration;

 - Rounding fixup to not waste memory in ecc_blocks;

 - Restore ECC information printouts;

 - A small code cleanup: use kmemdup where appropriate.

* tag 'for-v3.10' of git://git.infradead.org/users/cbou/linux-pstore:
  pstore/ram: Restore ecc information block
  pstore/ram: Allow specifying ecc parameters in platform data
  pstore/ram: Include ecc_size when calculating ecc_block
  pstore: Replace calls to kmalloc and memcpy with kmemdup

We can step on WARN_ON_ONCE() in sem_getref() if a semaphore is removed
just as we are about to call sem_getref() from semctl_main(); results
are not pretty.

We should fail with -EIDRM, same as if IPC_RM happened while we'd been
doing allocation there.  This also expands sem_getref() at its only
callsite (and fixed there), while sem_getref_and_unlock() is simply
killed off - it has no callers at all.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull drm updates from Dave Airlie:
 "This is the main drm pull request for 3.10.

  Wierd bits:
   - OMAP drm changes required OMAP dss changes, in drivers/video, so I
     took them in here.
   - one more fbcon fix for font handover
   - VT switch avoidance in pm code
   - scatterlist helpers for gpu drivers - have acks from akpm

  Highlights:
   - qxl kms driver - driver for the spice qxl virtual GPU

  Nouveau:
   - fermi/kepler VRAM compression
   - GK110/nvf0 modesetting support.

  Tegra:
   - host1x core merged with 2D engine support

  i915:
   - vt switchless resume
   - more valleyview support
   - vblank fixes
   - modesetting pipe config rework

  radeon:
   - UVD engine support
   - SI chip tiling support
   - GPU registers initialisation from golden values.

  exynos:
   - device tree changes
   - fimc block support

  Otherwise:
   - bunches of fixes all over the place."

* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (513 commits)
  qxl: update to new idr interfaces.
  drm/nouveau: fix build with nv50->nvc0
  drm/radeon: fix handling of v6 power tables
  drm/radeon: clarify family checks in pm table parsing
  drm/radeon: consolidate UVD clock programming
  drm/radeon: fix UPLL_REF_DIV_MASK definition
  radeon: add bo tracking debugfs
  drm/radeon: add new richland pci ids
  drm/radeon: add some new SI PCI ids
  drm/radeon: fix scratch reg handling for UVD fence
  drm/radeon: allocate SA bo in the requested domain
  drm/radeon: fix possible segfault when parsing pm tables
  drm/radeon: fix endian bugs in atom_allocate_fb_scratch()
  OMAPDSS: TFP410: return EPROBE_DEFER if the i2c adapter not found
  OMAPDSS: VENC: Add error handling for venc_probe_pdata
  OMAPDSS: HDMI: Add error handling for hdmi_probe_pdata
  OMAPDSS: RFBI: Add error handling for rfbi_probe_pdata
  OMAPDSS: DSI: Add error handling for dsi_probe_pdata
  OMAPDSS: SDI: Add error handling for sdi_probe_pdata
  OMAPDSS: DPI: Add error handling for dpi_probe_pdata
  ...

Signed-off-by: Dave Airlie <airlied@redhat.com>

Merge the fixes for the server driver dirty update paths
* server-fixes:
  drm/cirrus: deal with bo reserve fail in dirty update path
  drm/ast: deal with bo reserve fail in dirty update path
  drm/mgag200: deal with bo reserve fail in dirty update path

OMAPDSS fixes for 3.10:

* Compilation fix when DSI is disabled in Kconfig
* Basic deferred probe support to fix DT boot

* tag 'omapdss-for-3.10-fixes' of git://gitorious.org/linux-omap-dss2/linux:
  OMAPDSS: TFP410: return EPROBE_DEFER if the i2c adapter not found
  OMAPDSS: VENC: Add error handling for venc_probe_pdata
  OMAPDSS: HDMI: Add error handling for hdmi_probe_pdata
  OMAPDSS: RFBI: Add error handling for rfbi_probe_pdata
  OMAPDSS: DSI: Add error handling for dsi_probe_pdata
  OMAPDSS: SDI: Add error handling for sdi_probe_pdata
  OMAPDSS: DPI: Add error handling for dpi_probe_pdata
  OMAPDSS: VENC: use platform_driver_register()
  OMAPDSS: HDMI: use platform_driver_register()
  OMAPDSS: RFBI: use platform_driver_register()
  OMAPDSS: DSI: use platform_driver_register()
  OMAPDSS: SDI: use platform_driver_register()
  OMAPDSS: DPI: use platform_driver_register()
  OMAPFB: defer probe if no displays
  OMAPFB: use module_platform_driver()
  OMAPDSS: Makefile: move omapfb after panels
  OMAPDSS: DPI: fix compilation if DSI not compiled in