All operation related to the txWindow should be modulo 64.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

l2cap_data_channel do not free the S-frame, so we free it here.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Inside "case L2CAP_MODE_BASIC:" we don't need to check for sk_type and
L2CAP mode. So only the length check is fine.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Remove extra braces and labels, break over column 80 lines, etc
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

It also removes an unneeded check for the MTU. The check is done before
on sco_send_frame()
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reviewed-by: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Set the proper error(ENOMEM), instead of just return 0.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

A while back there was a discussion regarding the rt_secret_interval timer.
Given that we've had the ability to do emergency route cache rebuilds for awhile
now, based on a statistical analysis of the various hash chain lengths in the
cache, the use of the flush timer is somewhat redundant.  This patch removes the
rt_secret_interval sysctl, allowing us to rely solely on the statistical
analysis mechanism to determine the need for route cache flushes.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 39e0786d.

On request from microblaze developers, they are going to handle
this differently.
Signed-off-by: David S. Miller <davem@davemloft.net>

Add prefetches of the skb and the next rx descriptor to speed up rx path.

Use prefetchw() for the skb [suggested by Eric Dumazet].

The rx descriptor is in skb->data which is mapped for streaming mode DMA.
Eric Dumazet pointed out that we should not prefetch the data before
dma_sync.  So we prefetch only if dma_sync is no_op on the system.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

And turn on NETIF_F_GRO by default [requested by DaveM].
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The memory for the private data is allocated using kzalloc in
alloc_etherdev (or alloc_netdev_mq respectively) so there is no need to
set it to 0 again.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The memory for the private data is allocated using kzalloc in
alloc_etherdev (or alloc_netdev_mq respectively) so there is no need to
set it to 0 again.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The memory for the private data is allocated using kzalloc in
alloc_etherdev (or alloc_netdev_mq respectively) so there is no need to
set it to 0 again.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The memory for the private data is allocated using kzalloc in
alloc_etherdev (or alloc_netdev_mq respectively) so there is no need to
set the napi member it to 0 explicitely.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The memory for the private data is allocated using kzalloc in
alloc_etherdev (or alloc_netdev_mq respectively) so there is no need to
set it to 0 again.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The memory for the private data is allocated using kzalloc in
alloc_etherdev (or alloc_netdev_mq respectively) so there is no need to
set it to 0 again.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The memory for the private data is allocated using kzalloc in
alloc_etherdev (or alloc_netdev_mq respectively) so there is no need to
set it to 0 again.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The memory for the private data is allocated using kzalloc in
alloc_etherdev (or alloc_netdev_mq respectively) so there is no need to
set it to 0 again.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce ____napi_schedule() helper for callers in irq disabled
contexts. rps_trigger_softirq() becomes a leaf function.

Use container_of() in process_backlog() instead of accessing per_cpu
address.

Use a custom inlined version of __napi_complete() in process_backlog()
to avoid one locked instruction :

 only current cpu owns and manipulates this napi,
 and NAPI_STATE_SCHED is the only possible flag set on backlog.
 we can use a plain write instead of clear_bit(),
 and we dont need an smp_mb() memory barrier, since RPS is on,
 backlog is protected by a spinlock.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NET_IP_ALIGN defaults to 2, no need to override.

NET_SKB_PAD is now 64, which is much larger than microblaze's
L1_CACHE_SIZE so no need to override that either.
Signed-off-by: David S. Miller <davem@davemloft.net>

eth_type_trans() & get_rps_cpus() currently need two 64bytes cache
lines in packet to compute rxhash.

Increasing NET_SKB_PAD from 32 to 64 reduces the need to one cache
line only, and makes RPS faster.

NET_IP_ALIGN(2) + ethernet_header(14) + IP_header(20/40) + ports(8)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding addresses and ports to the short packet log message,
like ipv4/udp.c does it, makes these messages a lot more useful:

[  822.182450] UDPv6: short packet: From [2001:db8:ffb4:3::1]:47839 23715/178 to [2001:db8:ffb4:3:5054:ff:feff:200]:1234

This requires us to drop logging in case pskb_may_pull() fails,
which also is consistent with ipv4/udp.c
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the resource_size function instead of manually calculating the
resource size.  This reduces the chance of introducing off-by-one
errors.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reset the PHY before first accessing it.  Doing so, ensure that the PHY is
in a known good state before we read/write PHY registers. This fixes a
driver probe failure.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During Sx->S0 transitions, the interconnect between the MAC and PHY on
82577/82578 can remain in SMBus mode instead of transitioning to the
PCIe-like mode required during normal operation.  Toggling the LANPHYPC
Value bit essentially resets the interconnect forcing it to the correct
mode.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Based on Andy's work, but I modified a lot.

Similar to the patch for bridge, this patch does:

1) implement the 2 methods to support netpoll for bonding;

2) modify netpoll during forwarding packets via bonding;

3) disable netpoll support of bonding when a netpoll-unabled device
   is added to bonding;

4) enable netpoll support when all underlying devices support netpoll.

Cc: Andy Gospodarek <gospo@redhat.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Based on the previous patch, make bridge support netpoll by:

1) implement the 2 methods to support netpoll for bridge;

2) modify netpoll during forwarding packets via bridge;

3) disable netpoll support of bridge when a netpoll-unabled device
   is added to bridge;

4) enable netpoll support when all underlying devices support netpoll.

Cc: David Miller <davem@davemloft.net>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This whole patchset is for adding netpoll support to bridge and bonding
devices. I already tested it for bridge, bonding, bridge over bonding,
and bonding over bridge. It looks fine now.

To make bridge and bonding support netpoll, we need to adjust
some netpoll generic code. This patch does the following things:

1) introduce two new priv_flags for struct net_device:
   IFF_IN_NETPOLL which identifies we are processing a netpoll;
   IFF_DISABLE_NETPOLL is used to disable netpoll support for a device
   at run-time;

2) introduce one new method for netdev_ops:
   ->ndo_netpoll_cleanup() is used to clean up netpoll when a device is
     removed.

3) introduce netpoll_poll_dev() which takes a struct net_device * parameter;
   export netpoll_send_skb() and netpoll_poll_dev() which will be used later;

4) hide a pointer to struct netpoll in struct netpoll_info, ditto.

5) introduce ->real_dev for struct netpoll.

6) introduce a new status NETDEV_BONDING_DESLAE, which is used to disable
   netconsole before releasing a slave, to avoid deadlocks.

Cc: David Miller <davem@davemloft.net>
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the PF acks a message from the VF the VF gets an interrupt.  It
must cache the ack bit so that polling SW will not miss the ack.  Also
avoid reading the message buffer on acks because that also will clear
the ack bit.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver was calling the set Rx mode function for every multicast
filter set by the VF.  When starting many VMs where each might have
multiple VLAN interfaces this would result in the function being
called hundreds or even thousands of times.  This is unnecessary
for the case of the imperfect filters used in the MTA and has been
streamlined to be more efficient.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver is unnecessarily writing values to VLAN control registers.
These writes already done elsewhere and are superfluous here.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch reduces the number of skb cache misses in the
clean_tx_irq path, and results in an overall increase
in tx packet throughput.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Accessing ks8851 companion eeprom permits modifying the ks8851 stored
MAC address.

Example how to change the MAC address using ethtool, to set the
01:23:45:67:89:AB MAC address:
$ echo "0:AB8976452301" | xxd -r > mac.bin
$ sudo ethtool -E eth0 magic 0x8870 offset 2 < mac.bin
Signed-off-by: Sebastien Jan <s-jan@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Low-level functions provide 16bits words read and write capability
to ks8851 companion eeprom.
Signed-off-by: Sebastien Jan <s-jan@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

CCR register contains information on companion eeprom availability.
Signed-off-by: Sebastien Jan <s-jan@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Repeated calls to nv_rx_process in napi poll routine do not take
portion of budget that has been consumed in previous calls.  Fix by
subtracting the number of packets processed.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>