- 17 Dec, 2018 7 commits
-
-
Christoph Hellwig authored
Now that the block layer checks if a queue map has any queues inside it there is no more reason to duplicate the maps for the non-default types. Reviewed-by:
Ming Lei <ming.lei@redhat.com> Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Jens Axboe <axboe@kernel.dk>
-
Christoph Hellwig authored
We should check if a given queue map actually has queues enabled before dispatching to it. This allows drivers to not initialize optional but not used map types, which subsequently will allow fixing problems with queue map rebuilds for that case. Reviewed-by:
-
Ming Lei authored
Now we only export hctx->type via sysfs, and there isn't such info in hctx entry under debugfs. We often use debugfs only to diagnose queue mapping issue, so add the support in debugfs. Queue mapping becomes a bit more complicated after multiple queue mapping is supported, we may write blktest to verify if queue mapping is valid based on blk-mq-debugfs. Given not necessary to export hctx->type twice, so remove the export from sysfs. Cc: Jeff Moyer <jmoyer@redhat.com> Cc: Mike Snitzer <snitzer@redhat.com> Reviewed-by:
-
Ming Lei authored
Type of each element in queue mapping table is 'unsigned int, intead of 'struct blk_mq_queue_map)', so fix it. Cc: Jeff Moyer <jmoyer@redhat.com> Cc: Mike Snitzer <snitzer@redhat.com> Cc: Christoph Hellwig <hch@lst.de> Reviewed-by:
-
Ming Lei authored
This information is helpful to either investigate issues, or understand wbt's internal behaviour. Cc: Bart Van Assche <bart.vanassche@wdc.com> Cc: Omar Sandoval <osandov@fb.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Josef Bacik <josef@toxicpanda.com> Signed-off-by:
-
Ming Lei authored
blk-mq-debugfs has been proved as very helpful for debug some tough issues, such as IO hang. We have seen blk-wbt related IO hang several times, even inside Red Hat BZ, there is such report not sovled yet, so this patch adds support debugfs on rq_qos. Cc: Bart Van Assche <bart.vanassche@wdc.com> Cc: Omar Sandoval <osandov@fb.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Josef Bacik <josef@toxicpanda.com> Signed-off-by:
-
Damien Le Moal authored
Add the description of the zoned, nr_zones and chunk_sectors sysfs queue attributes to Documentation/block/queue-sysfs.txt. The description of the zoned and chunk_sector attributes are mostly copied from ABI/testing/sysfs-block (added a typo fix). While at it, also fix a typo in the description of the io_poll_delay attribute. nr_zones description is also added to ABI/testing/sysfs-block and contact email address updated for the zoned attribute. Signed-off-by:
Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by:
-
- 16 Dec, 2018 8 commits
-
-
Chengguang Xu authored
blk_mq_init_queue() will not return NULL pointer to its caller, so it's better to replace IS_ERR_OR_NULL using IS_ERR in loop_add(). If in the future things change to check NULL pointer inside loop_add(), we should return -ENOMEM as return code instead of PTR_ERR(NULL). Signed-off-by:
Chengguang Xu <cgxu519@gmx.com> Signed-off-by:
-
Chengguang Xu authored
Add __exit annotation to cleanup helper which is only called once in the module. Signed-off-by:
-
Christoph Hellwig authored
This prevents a HIPRI bio from being submitted through a stacking driver that does not support polling and thus won't poll for I/O completion. Signed-off-by:
-
Jianchao Wang authored
Replace blk_mq_request_issue_directly with blk_mq_try_issue_directly in blk_insert_cloned_request and kill it as nobody uses it any more. Signed-off-by:
Jianchao Wang <jianchao.w.wang@oracle.com> Signed-off-by:
-
Jianchao Wang authored
It is not necessary to issue request directly with bypass 'true' in blk_mq_sched_insert_requests and handle the non-issued requests itself. Just set bypass to 'false' and let blk_mq_try_issue_directly handle them totally. Remove the blk_rq_can_direct_dispatch check, because blk_mq_try_issue_directly can handle it well.If request is direct-issued unsuccessfully, insert the reset. Signed-off-by:
-
Jianchao Wang authored
Merge blk_mq_try_issue_directly and __blk_mq_try_issue_directly into one interface to unify the interfaces to issue requests directly. The merged interface takes over the requests totally, it could insert, end or do nothing based on the return value of .queue_rq and 'bypass' parameter. Then caller needn't any other handling any more and then code could be cleaned up. And also the commit c616cbee ( blk-mq: punt failed direct issue to dispatch list ) always inserts requests to hctx dispatch list whenever get a BLK_STS_RESOURCE or BLK_STS_DEV_RESOURCE, this is overkill and will harm the merging. We just need to do that for the requests that has been through .queue_rq. This patch also could fix this. Signed-off-by:
-
Christoph Hellwig authored
Signed-off-by:
-
Christoph Hellwig authored
Signed-off-by:
-
- 14 Dec, 2018 4 commits
-
-
Christoph Hellwig authored
Signed-off-by:
-
Christoph Hellwig authored
Signed-off-by:
-
Christoph Hellwig authored
Signed-off-by:
-
Christoph Hellwig authored
Signed-off-by:
-
- 13 Dec, 2018 21 commits
-
-
Sagi Grimberg authored
free the controller discard_page correctly. Fixes: cb5b7262 ("nvme: provide fallback for discard alloc failure") Signed-off-by:
Sagi Grimberg <sagi@grimberg.me> Signed-off-by:
-
git://git.infradead.org/nvmeJens Axboe authored
Pull NVMe updates from Christoph: "Here is the second large chunk of nvme updates for 4.21: - host and target support for NVMe over TCP (Sagi Grimberg, Roy Shterman, Solganik Alexander) - error log page support in target (Chaitanya Kulkarni) plus small fixes and improvements from Jens Axboe and Chengguang Xu." * 'nvme-4.21' of git://git.infradead.org/nvme: (33 commits) nvme-rdma: support separate queue maps for read and write nvme-tcp: support separate queue maps for read and write nvme-fabrics: allow user to set nr_write_queues for separate queue maps nvme-fabrics: add missing nvmf_ctrl_options documentation blk-mq-rdma: pass in queue map to blk_mq_rdma_map_queues nvmet: update smart log with num err log entries nvmet: add error log page cmd handler nvmet: add error log support for file backend nvmet: add error log support for bdev backend nvmet: add error log support for admin-cmd nvmet: add error log support for rdma backend nvmet: add error log support for fabrics-cmd nvmet: add error log support in the core nvmet: add interface to update error-log page nvmet: add error-log definitions nvme: add error log page slot definition nvme: remove nvme_common command cdw10 array nvmet: remove unused variable nvme: provide fallback for discard alloc failure nvme: add __exit annotation ...
-
Guoju Fang authored
Sometimes flush journal may be very frequent, so it's useful to dump number of keys every time write journal. Signed-off-by:
Guoju Fang <fangguoju@gmail.com> Signed-off-by:
Coly Li <colyli@suse.de> Signed-off-by:
-
Coly Li authored
Because CUTOFF_WRITEBACK is defined as 40, so before the changes of dynamic cutoff writeback values, writeback_percent is limited to [0, CUTOFF_WRITEBACK]. Any value larger than CUTOFF_WRITEBACK will be fixed up to 40. Now cutof writeback limit is a dynamic value bch_cutoff_writeback, so the range of writeback_percent can be a more flexible range as [0, bch_cutoff_writeback]. The flexibility is, it can be expended to a larger or smaller range than [0, 40], depends on how value bch_cutoff_writeback is specified. The default value is still strongly recommended to most of users for most of workloads. But for people who want to do research on bcache writeback perforamnce tuning, they may have chance to specify more flexible writeback_percent in range [0, 70]. Signed-off-by:
-
Coly Li authored
Currently the cutoff writeback and cutoff writeback sync thresholds are defined by CUTOFF_WRITEBACK (40) and CUTOFF_WRITEBACK_SYNC (70) as static values. Most of time these they work fine, but when people want to do research on bcache writeback mode performance tuning, there is no chance to modify the soft and hard cutoff writeback values. This patch introduces two module parameters bch_cutoff_writeback_sync and bch_cutoff_writeback which permit people to tune the values when loading bcache.ko. If they are not specified by module loading, current values CUTOFF_WRITEBACK_SYNC and CUTOFF_WRITEBACK will be used as default and nothing changes. When people want to tune this two values, - cutoff_writeback can be set in range [1, 70] - cutoff_writeback_sync can be set in range [1, 90] - cutoff_writeback always <= cutoff_writeback_sync The default values are strongly recommended to most of users for most of workloads. Anyway, if people wants to take their own risk to do research on new writeback cutoff tuning for their own workload, now they can make it. Signed-off-by:
-
Coly Li authored
This patch moves MODULE_AUTHOR and MODULE_LICENSE to end of super.c, and add MODULE_DESCRIPTION("Bcache: a Linux block layer cache"). This is preparation for adding module parameters. Signed-off-by: -
Coly Li authored
The option gc_after_writeback is disabled by default, because garbage collection will discard SSD data which drops cached data. Echo 1 into /sys/fs/bcache/<UUID>/internal/gc_after_writeback will enable this option, which wakes up gc thread when writeback accomplished and all cached data is clean. This option is helpful for people who cares writing performance more. In heavy writing workload, all cached data can be clean only happens when writeback thread cleans all cached data in I/O idle time. In such situation a following gc running may help to shrink bcache B+ tree and discard more clean data, which may be helpful for future writing requests. If you are not sure whether this is helpful for your own workload, please leave it as disabled by default. Signed-off-by:
-
Coly Li authored
Garbage collection thread starts to work when c->sectors_to_gc is negative value, otherwise nothing will happen even the gc thread is woken up by wake_up_gc(). force_wake_up_gc() sets c->sectors_to_gc to -1 before calling wake_up_gc(), then gc thread may have chance to run if no one else sets c->sectors_to_gc to a positive value before gc_should_run(). This routine can be called where the gc thread is woken up and required to run in force. Signed-off-by:
-
Shenghui Wang authored
"echo 1 > writeback_running" marks writeback_running even if no writeback kthread created as "d_strtoul(writeback_running)" will simply set dc-> writeback_running without checking the existence of dc->writeback_thread. Add check for setting writeback_running via sysfs: if no writeback kthread available, reject setting to 1. v2 -> v3: * Make message on wrong assignment more clear. * Print name of bcache device instead of name of backing device. Signed-off-by:
Shenghui Wang <shhuiw@foxmail.com> Signed-off-by:
-
Shenghui Wang authored
A fresh backing device is not attached to any cache_set, and has no writeback kthread created until first attached to some cache_set. But bch_cached_dev_writeback_init run " dc->writeback_running = true; WARN_ON(test_and_clear_bit(BCACHE_DEV_WB_RUNNING, &dc->disk.flags)); " for any newly formatted backing devices. For a fresh standalone backing device, we can get something like following even if no writeback kthread created: ------------------------ /sys/block/bcache0/bcache# cat writeback_running 1 /sys/block/bcache0/bcache# cat writeback_rate_debug rate: 512.0k/sec dirty: 0.0k target: 0.0k proportional: 0.0k integral: 0.0k change: 0.0k/sec next io: -15427384ms The none ZERO fields are misleading as no alive writeback kthread yet. Set dc->writeback_running false as no writeback thread created in bch_cached_dev_writeback_init(). We have writeback thread created and woken up in bch_cached_dev_writeback _start(). Set dc->writeback_running true before bch_writeback_queue() called, as a writeback thread will check if dc->writeback_running is true before writing back dirty data, and hung if false detected. After the change, we can get the following output for a fresh standalone backing device: ----------------------- /sys/block/bcache0/bcache$ cat writeback_running 0 /sys/block/bcache0/bcache# cat writeback_rate_debug rate: 0.0k/sec dirty: 0.0k target: 0.0k proportional: 0.0k integral: 0.0k change: 0.0k/sec next io: 0ms v1 -> v2: Set dc->writeback_running before bch_writeback_queue() called, Signed-off-by:
-
Shenghui Wang authored
We have struct cached_dev allocated by kzalloc in register_bcache(), which initializes all the fields of cached_dev with 0s. And commit ce4c3e19 ("bcache: Replace bch_read_string_list() by __sysfs_match_string()") has remove the string "default". Update the comment. Signed-off-by:
-
Shenghui Wang authored
commit 220bb38c ("bcache: Break up struct search") introduced changes to struct search and s->iop. bypass/bio are fields of struct data_insert_op now. Update the comment. Signed-off-by:
-
Shenghui Wang authored
debugfs_remove and debugfs_remove_recursive will check if the dentry pointer is NULL or ERR, and will do nothing in that case. Remove the check in cache_set_free and bch_debug_init. Signed-off-by:
-
Shenghui Wang authored
We have the following define for btree iterator: struct btree_iter { size_t size, used; #ifdef CONFIG_BCACHE_DEBUG struct btree_keys *b; #endif struct btree_iter_set { struct bkey *k, *end; } data[MAX_BSETS]; }; We can see that the length of data[] field is static MAX_BSETS, which is defined as 4 currently. But a btree node on disk could have too many bsets for an iterator to fit on the stack - maybe far more that MAX_BSETS. Have to dynamically allocate space to host more btree_iter_sets. bch_cache_set_alloc() will make sure the pool cache_set->fill_iter can allocate an iterator equipped with enough room that can host (sb.bucket_size / sb.block_size) btree_iter_sets, which is more than static MAX_BSETS. bch_btree_node_read_done() will use that pool to allocate one iterator, to host many bsets in one btree node. Add more comment around cache_set->fill_iter to make code less confusing. Signed-off-by: -
Sagi Grimberg authored
llow NVMF_OPT_NR_WRITE_QUEUES to describe additional write queues. In addition, implement .map_queues that will apply 2 queue maps for read and write queue sets. Note that with the separate queue map, HCTX_TYPE_READ will always use nr_io_queues and HCTX_TYPE_DEFAULT will use nr_write_queues. Signed-off-by:
-
Sagi Grimberg authored
Allow NVMF_OPT_NR_WRITE_QUEUES to describe additional write queues. In addition, implement .map_queues that will apply 2 queue maps for read and write queue sets. Note that with the separate queue map, HCTX_TYPE_READ will always use nr_io_queues and HCTX_TYPE_DEFAULT will use nr_write_queues. Signed-off-by:
-
Sagi Grimberg authored
This argument will specify how many I/O queues will be connected in create_ctrl in addition to nr_io_queues. With this configuration, I/O that carries payload from the host to the target, will use the default hctx queue map, and I/O that involves target to host transfers will use the read hctx queue map. Signed-off-by:
-
Sagi Grimberg authored
Signed-off-by:
-
Sagi Grimberg authored
Will be used by nvme-rdma for queue map separation support. Signed-off-by:
-
Chaitanya Kulkarni authored
Now that we have error log page implementation update smart log command handler to provide number of error log entries in the lifetime of the controller field. Signed-off-by:
Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Reviewed-by:
-
Chaitanya Kulkarni authored
Now that we have support for all the major parts of the target we add a NVMe error log page handler so that host can read the log page. Signed-off-by:
-
