- 11 Oct, 2007 14 commits
-
-
David Brownell authored
Make the NGW100 bitbang i2c use open drain signaling. Also, speed it up, so it's closer to 100 kHz ... the code paths seem to be long enough that the udelay isn't dominating bit times. The peak bit rate I observed was around 125 kHz, but that's with large delays (usually before ACK/NAK) which hold the overall rate down to around 80 kHz (call it 100 usec/byte on average). Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
-
Haavard Skinnemoen authored
Ignore a few syscalls that are irrelevant because they're either old, depends on NUMA or depends on SMP. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
-
Kristoffer Nyborg Gregertsen authored
This patch makes the SMC configuration take timings in clock cycles instead of nanoseconds. A function to calculate timings in clock cycles is added. This patch removes the rounding troubles of the previous SMC configuration method. [hskinnemoen@atmel.com: fix atstk1002/atngw100 flash config] Signed-off-by: Kristoffer Nyborg Gregertsen <gregerts@stud.ntnu.no> Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
-
Robert P. J. Day authored
Given the existing "retain_initrd" boot-time parameter defined in init/initramfs.c, there appears to be no need for the equivalent "keepinitrd" parameter. Signed-off-by: Robert P. J. Day <rpjday@mindspring.com> Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
-
Haavard Skinnemoen authored
I don't think the dma_sync_*_for_cpu ever did anything useful. We flush the relevant cache lines when mapping the buffer or when calling dma_sync_*_for_device(), and the CPU isn't allowed to touch the buffer after that. In other words, if these functions actually have anything to flush from the caches, we're already in trouble. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
-
Haavard Skinnemoen authored
__init_end, which comes immediately before .text, is already page aligned, and that should be more than enough for the .text section. The reason why we need to align the .text section is because the interrupt handler offset is ORed with EVBA, so we need to provide enough alignment of EVBA that this OR operation works as an ADD. Currently, the last interrupt handler is not nearly a full page away from EVBA, so it won't be a problem. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
-
Haavard Skinnemoen authored
Use PAGE_SIZE, THREAD_SIZE and L1_CACHE_BYTES instead of harcoded constants in places where that's what we really mean. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
-
Sam Ravnborg authored
Rename vmlinux.lds to a .S file to match other architectures. Simplify Makefile to match the rename and deleted the unused USE_STANDARD_AS_RULE Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
-
Matteo Vit authored
Signed-off-by: Matteo Vit - Dave S.r.l. <matteo.vit@dave.eu> Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
-
Haavard Skinnemoen authored
Add regexes to recognize stack frame adjustments in AVR32 code. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
-
Haavard Skinnemoen authored
Implement at32_add_device_usba() and use it to wire up the USBA device on ATSTK1000 and ATNGW100. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
-
Matteo Vit authored
This patch add multidrive support for pio driver Signed-off-by: Matteo Vit - Dave S.r.l. <matteo.vit@dave.eu> Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
-
David Brownell authored
When debugfs is available, /sys/kernel/debug/at32ap_clk will provide a dump of the power manager registers and of the current clock tree. This can help sorting out various surprises, and when making runtime PM work. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
-
Haavard Skinnemoen authored
We don't want to redefine this in every file that needs to access the PM. Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
-
- 09 Oct, 2007 7 commits
-
-
Linus Torvalds authored
-
git://ftp.linux-mips.org/pub/scm/upstream-linusLinus Torvalds authored
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: [MIPS] Au1000: set the PCI controller IO base [MIPS] Alchemy: Fix USB initialization. [MIPS] IP32: Fix fatal typo in address computation.
-
Trond Myklebust authored
The recent fix for a circular lock dependency unfortunately introduced a potential memory leak in the event where the call to nlmsvc_lookup_host fails for some reason. Thanks to Roel Kluin for spotting this. Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Jeff Garzik authored
The recent mv_fill_sg() rewrite, to fix a data corruption problem related to IOMMU virtual merging, forgot to account for the potentially-increased size of the scatter/gather table after its run. Additionally, the DMA boundary is reduced from 0xffffffff to 0xffff to more closely match the needs of mv_fill_sg(). Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Florian Fainelli authored
The PCI controller IO base was not set in the au1000 pci code. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John Crispin <blogic@openwrt.org> Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Florian Fainelli authored
This patch fixes a wrong ifdef in the board setup code, leading to the GPIO pin not being pulled high, and thus the USB switch not being powered at all. This finishes the rename of CONFIG_USB_OHCI to CONFIG_USB_OHCI_HCD, which started in 2005 (before 2.6.12-rc2), then probably because things were working anyway for most people got forgotten. [Ralf: Paolo's original patch didn't fix the module case, Florian's patch only fixed MTX1 etc. so this is a combined patch plus some cleanups.] Cc: Giuseppe Patanè <giuseppe.patane@tvblob.com> Cc: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John Crispin <blogic@openwrt.org> Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Giuseppe Sacco authored
Signed-off-by: Giuseppe Sacco <eppesuig@debian.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
- 08 Oct, 2007 11 commits
-
-
Maarten Bressers authored
When building a custom keymap, after setting GENERATE_KEYMAP := 1 in drivers/char/Makefile, the kernel build fails like this: CC drivers/char/vt.o make[2]: *** No rule to make target `drivers/char/%.map', needed by `drivers/char/defkeymap.c'. Stop. make[1]: *** [drivers/char] Error 2 make: *** [drivers] Error 2 This was caused by commit af8b1287, which deleted a necessary colon from the Makefile rule that generates the keymap, since that rule contains both a target and a target-pattern. The following patch puts the colon back: Signed-off-by: Maarten Bressers <mbres@gentoo.org> Cc: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Karsten Keil authored
Fix against access random data bytes outside the dev->chanmap array. Thanks to Oliver Neukum for pointing me to this issue. Signed-off-by: Karsten Keil <kkeil@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Linus Torvalds authored
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: [IPv6]: Fix ICMPv6 redirect handling with target multicast address [PKT_SCHED] cls_u32: error code isn't been propogated properly [ROSE]: Fix rose.ko oops on unload [TCP]: Fix fastpath_cnt_hint when GSO skb is partially ACKed
-
Yan Zheng authored
When IOCB_FLAG_RESFD flag is set and iocb->aio_resfd is incorrect, statement 'goto out_put_req' is executed. At label 'out_put_req', aio_put_req(..) is called, which requires 'req->ki_filp' set. Signed-off-by: Yan Zheng<yanzheng@21cn.com> Cc: Zach Brown <zach.brown@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Yan Zheng authored
find_lock_page increases page's usage count, we should decrease it before return VM_FAULT_SIGBUS Signed-off-by: Yan Zheng<yanzheng@21cn.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Yan Zheng authored
The test for VM_CAN_NONLINEAR always fails Signed-off-by: Yan Zheng<yanzheng@21cn.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Peter Zijlstra authored
All the current page_mkwrite() implementations also set the page dirty. Which results in the set_page_dirty_balance() call to _not_ call balance, because the page is already found dirty. This allows us to dirty a _lot_ of pages without ever hitting balance_dirty_pages(). Not good (tm). Force a balance call if ->page_mkwrite() was successful. Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Brian Haley authored
When the ICMPv6 Target address is multicast, Linux processes the redirect instead of dropping it. The problem is in this code in ndisc_redirect_rcv(): if (ipv6_addr_equal(dest, target)) { on_link = 1; } else if (!(ipv6_addr_type(target) & IPV6_ADDR_LINKLOCAL)) { ND_PRINTK2(KERN_WARNING "ICMPv6 Redirect: target address is not link-local.\n"); return; } This second check will succeed if the Target address is, for example, FF02::1 because it has link-local scope. Instead, it should be checking if it's a unicast link-local address, as stated in RFC 2461/4861 Section 8.1: - The ICMP Target Address is either a link-local address (when redirected to a router) or the same as the ICMP Destination Address (when redirected to the on-link destination). I know this doesn't explicitly say unicast link-local address, but it's implied. This bug is preventing Linux kernels from achieving IPv6 Logo Phase II certification because of a recent error that was found in the TAHI test suite - Neighbor Disovery suite test 206 (v6LC.2.3.6_G) had the multicast address in the Destination field instead of Target field, so we were passing the test. This won't be the case anymore. The patch below fixes this problem, and also fixes ndisc_send_redirect() to not send an invalid redirect with a multicast address in the Target field. I re-ran the TAHI Neighbor Discovery section to make sure Linux passes all 245 tests now. Signed-off-by: Brian Haley <brian.haley@hp.com> Acked-by: David L Stevens <dlstevens@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Stephen Hemminger authored
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alexey Dobriyan authored
Commit a3d38402 aka "[AX.25]: Fix unchecked rose_add_loopback_neigh uses" transformed rose_loopback_neigh var into statically allocated one. However, on unload it will be kfree's which can't work. Steps to reproduce: modprobe rose rmmod rose BUG: unable to handle kernel NULL pointer dereference at virtual address 00000008 printing eip: c014c664 *pde = 00000000 Oops: 0000 [#1] PREEMPT DEBUG_PAGEALLOC Modules linked in: rose ax25 fan ufs loop usbhid rtc snd_intel8x0 snd_ac97_codec ehci_hcd ac97_bus uhci_hcd thermal usbcore button processor evdev sr_mod cdrom CPU: 0 EIP: 0060:[<c014c664>] Not tainted VLI EFLAGS: 00210086 (2.6.23-rc9 #3) EIP is at kfree+0x48/0xa1 eax: 00000556 ebx: c1734aa0 ecx: f6a5e000 edx: f7082000 esi: 00000000 edi: f9a55d20 ebp: 00200287 esp: f6a5ef28 ds: 007b es: 007b fs: 0000 gs: 0033 ss: 0068 Process rmmod (pid: 1823, ti=f6a5e000 task=f7082000 task.ti=f6a5e000) Stack: f9a55d20 f9a5200c 00000000 00000000 00000000 f6a5e000 f9a5200c f9a55a00 00000000 bf818cf0 f9a51f3f f9a55a00 00000000 c0132c60 65736f72 00000000 f69f9630 f69f9528 c014244a f6a4e900 00200246 f7082000 c01025e6 00000000 Call Trace: [<f9a5200c>] rose_rt_free+0x1d/0x49 [rose] [<f9a5200c>] rose_rt_free+0x1d/0x49 [rose] [<f9a51f3f>] rose_exit+0x4c/0xd5 [rose] [<c0132c60>] sys_delete_module+0x15e/0x186 [<c014244a>] remove_vma+0x40/0x45 [<c01025e6>] sysenter_past_esp+0x8f/0x99 [<c012bacf>] trace_hardirqs_on+0x118/0x13b [<c01025b6>] sysenter_past_esp+0x5f/0x99 ======================= Code: 05 03 1d 80 db 5b c0 8b 03 25 00 40 02 00 3d 00 40 02 00 75 03 8b 5b 0c 8b 73 10 8b 44 24 18 89 44 24 04 9c 5d fa e8 77 df fd ff <8b> 56 08 89 f8 e8 84 f4 fd ff e8 bd 32 06 00 3b 5c 86 60 75 0f EIP: [<c014c664>] kfree+0x48/0xa1 SS:ESP 0068:f6a5ef28 Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ilpo Järvinen authored
When only GSO skb was partially ACKed, no hints are reset, therefore fastpath_cnt_hint must be tweaked too or else it can corrupt fackets_out. The corruption to occur, one must have non-trivial ACK/SACK sequence, so this bug is not very often that harmful. There's a fackets_out state reset in TCP because fackets_out is known to be inaccurate and that fixes the issue eventually anyway. In case there was also at least one skb that got fully ACKed, the fastpath_skb_hint is set to NULL which causes a recount for fastpath_cnt_hint (the old value won't be accessed anymore), thus it can safely be decremented without additional checking. Reported by Cedric Le Goater <clg@fr.ibm.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 07 Oct, 2007 8 commits
-
-
Dmitry Torokhov authored
We should only reparent to a class former class devices that form the base of class hierarchy. Nested devices should still grow from their real parents. Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Tested-by: Andrey Borzenkov <arvidjaar@mail.ru> Tested-by: Anssi Hannula <anssi.hannula@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: firewire: point to migration document
-
Attila Kinali authored
Add the manufacturer and card id of teltonica pcmcia modems to serial_cs.c Signed-off-by: Attila Kinali <attila@kinali.ch> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Pavel Machek authored
Document sequence of keypresses that actually works. Yes, this changed year-or-so ago. Signed-off-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Al Viro authored
Async signals should not be reported as sent by current in audit log. As it is, we call audit_signal_info() too early in check_kill_permission(). Note that check_kill_permission() has that test already - it needs to know if it should apply current-based permission checks. So the solution is to move the call of audit_signal_info() between those. Bogosity in question is easily reproduced - add a rule watching for e.g. kill(2) from specific process (so that audit_signal_info() would not short-circuit to nothing), say load_policy, watch the bogus OBJ_PID entry in audit logs claiming that write(2) on selinuxfs file issued by load_policy(8) had somehow managed to send a signal to syslogd... Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Acked-by: Steve Grubb <sgrubb@redhat.com> Acked-by: Eric Paris <eparis@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Alexey Dobriyan authored
Modulat lguest started giving linking errors MODPOST 1 modules ERROR: "kasprintf" [drivers/lguest/lg.ko] undefined! Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru> Cc: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Peter Zijlstra authored
Provide some documentation for CONFIG_LOCK_STAT. Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Acked-by: Ingo Molnar <mingo@elte.hu> Cc: "Randy.Dunlap" <rdunlap@xenotime.net> Cc: Rob Landley <rob@landley.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Rafal Bilski authored
VIA C3 Ezra-T has RevisionID equal to 1, but it needs RevisionKey to be 0 or CPU will ignore new frequency and will continue to work at old frequency. New "revid_errata" option will force RevisionKey to be set to 0, whatever RevisionID is. Additionaly "Longhaul" will not silently ignore unsuccessful transition. It will try to check if "revid_errata" or "disable_acpi_c3" options need to be enabled for this processor/system. Same for Longhaul ver. 2 support. It will be disabled if none of above options will work. Best case scenario (with patch apllied and v2 enabled): longhaul: VIA C3 'Ezra' [C5C] CPU detected. Longhaul v2 supported. longhaul: Using northbridge support. longhaul: VRM 8.5 longhaul: Max VID=1.350 Min VID=1.050, 13 possible voltage scales longhaul: f: 300000 kHz, index: 0, vid: 1050 mV [...] longhaul: Voltage scaling enabled. Worst case scenario: longhaul: VIA C3 'Ezra-T' [C5M] CPU detected. Powersaver supported. longhaul: Using northbridge support. longhaul: Using ACPI support. longhaul: VRM 8.5 longhaul: Claims to support voltage scaling but min & max are both 1.250. Voltage scaling disabled longhaul: Failed to set requested frequency! longhaul: Enabling "Ignore Revision ID" option. longhaul: Failed to set requested frequency! longhaul: Disabling ACPI C3 support. longhaul: Disabling "Ignore Revision ID" option. longhaul: Failed to set requested frequency! longhaul: Enabling "Ignore Revision ID" option. [akpm@linux-foundation.org: coding-style cleanups] Signed-off-by: Rafal Bilski <rafalbilski@interia.pl> Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-