There is a hunk of code that is incorrectly indented with spaces
and rather than a tab.  Clean this up.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Russell King says:

====================
Add SFF module support

Add support for SFF modules.  SFF modules are similar to SFP modules,
but they have fewer control signals, and are soldered down rather than
pluggable.

They also have different IDs in the EEPROM to identify as soldered down
SFF modules.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for SFF modules, which are soldered down SFP modules.
These have a different phys_id value, and also have the present and
rate select signals omitted compared with their socketed counter-parts.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add "sff,sff" for SFF module support with SFP.  These have a different
phys_id value, and also have the present and rate select signals omitted
compared with their socketed counter-parts.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Horman says:

====================
nfp: fix rtsym and XPB register handling in debug dump

this series resolves two problems in the recently added debug dump facility.

* Correctly handle reading absolute rtysms
* Correctly handle special-case PB register reads

These fixes are for code only present in net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

For XPB registers reads, some island IDs require special handling (e.g.
ARM island), which is already taken care of in nfp_xpb_readl(), so use
that instead of a straight CPP read.

Without this fix all "xpbm:ArmIsldXpbmMap.*" registers are reported as
0xffffffff. It has also been observed to cause a system reboot.

With this fix correct values are reported, none of which are 0xffffffff.

The values may be read using ethtool debug level 2.
 # ethtool -W <netdev> 2
 # ethtool -w <netdev> data dump.dat

Fixes: 0e6c4955 ("nfp: dump CPP, XPB and direct ME CSRs")
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In TLV-based ethtool debug dumps, don't do a CPP read for absolute
rtsyms, use the addr field in the symbol table directly as the value.

Without this fix rtsym gro_release_ring_0 is 4 bytes of zeros.
With this fix the correct value, 0x0000004a 0x00000000 is reported.

The values may be read using ethtool debug level 2.
 # ethtool -W <netdev> 2
 # ethtool -w <netdev> data dump.dat

Fixes: e1e798e3 ("nfp: dump rtsyms")
Signed-off-by: Carl Heymann <carl.heymann@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

William Tu says:

====================
ERSPAN version 2 (type III) support

ERSPAN has two versions, v1 (type II) and v2 (type III).  This patch
series add support for erspan v2 based on existing erspan v1
implementation.  The first patch refactors the existing erspan v1's
header structure, making it extensible to put additional v2's header.
The second and third patch introduces erspan v2's implementation to
ipv4 and ipv6 erspan, for both native mode and collect metadata mode.
Finally, test cases are added under the samples/bpf.

Note:
ERSPAN version 2 has many features and this patch does not implement
all.  One major use case of version 2 over version 1 is its timestamp
and direction.  So the traffic collector is able to distinguish the
mirrorred traffic better.  Other features such as SGT (security group
tag), FT (frame type) for carrying non-ethernet packet, and optional
subheader are not implemented yet.

Example commandline for ERSPAN version 2:
ip link add dev ip6erspan11 type ip6erspan seq key 102 \
	local fc00:100::2 remote fc00:100::1 \
	erspan_ver 2 erspan_dir 1 erspan_hwid 17

The corresponding iproute2 patch:
https://marc.info/?l=linux-netdev&m=151321141525106&w=2

William Tu (4):
  net: erspan: refactor existing erspan code
  net: erspan: introduce erspan v2 for ip_gre
  ip6_gre: add erspan v2 support
  samples/bpf: add erspan v2 sample code

 include/net/erspan.h           | 152 ++++++++++++++++++++++++++++++++++++++---
 include/net/ip6_tunnel.h       |   3 +
 include/net/ip_tunnels.h       |   5 +-
 include/uapi/linux/if_ether.h  |   1 +
 include/uapi/linux/if_tunnel.h |   3 +
 net/ipv4/ip_gre.c              | 124 +++++++++++++++++++++++++++------
 net/ipv6/ip6_gre.c             | 139 +++++++++++++++++++++++++++++++------
 net/openvswitch/flow_netlink.c |   8 +--
 samples/bpf/tcbpf2_kern.c      |  77 ++++++++++++++++++---
 samples/bpf/test_tunnel_bpf.sh |  38 ++++++++---
 10 files changed, 472 insertions(+), 78 deletions(-)

--
A simple script to test it:

set -ex
function cleanup() {
	set +ex
	ip netns del ns0
	ip link del ip6erspan11
	ip link del veth1
}

function main() {
	trap cleanup 0 2 3 9

	ip netns add ns0
	ip link add veth0 type veth peer name veth1
	ip link set veth0 netns ns0

	# non-namespace
	ip addr add dev veth1 fc00:100::2/96

	if [ "$1" == "v1" ]; then
		echo "create IP6 ERSPAN v1 tunnel"
		ip link add dev ip6erspan11 type ip6erspan seq key 102 \
			local fc00:100::2 remote fc00:100::1 \
			erspan 123 erspan_ver 1
	else
		echo "create IP6 ERSPAN v2 tunnel"
		ip link add dev ip6erspan11 type ip6erspan seq key 102 \
			local fc00:100::2 remote fc00:100::1 \
			erspan_ver 2 erspan_dir 1 erspan_hwid 17
	fi
	ip addr add dev ip6erspan11 fc00:200::2/96
	ip addr add dev ip6erspan11 10.10.200.2/24

	# namespace: ns0
	ip netns exec ns0 ip addr add fc00:100::1/96 dev veth0

	if [ "$1" == "v1" ]; then
		ip netns exec ns0 \
		ip link add dev ip6erspan00 type ip6erspan seq key 102 \
			local fc00:100::1 remote fc00:100::2 \
			erspan 123 erspan_ver 1
	else
		ip netns exec ns0 \
		ip link add dev ip6erspan00 type ip6erspan seq key 102 \
			local fc00:100::1 remote fc00:100::2 \
			erspan_ver 2 erspan_dir 1 erspan_hwid 7
	fi

	ip netns exec ns0 ip addr add dev ip6erspan00 fc00:200::1/96
	ip netns exec ns0 ip addr add dev ip6erspan00 10.10.200.1/24

	ip link set dev veth1 up
	ip link set dev ip6erspan11 up
	ip netns exec ns0 ip link set dev ip6erspan00 up
	ip netns exec ns0 ip link set dev veth0 up
}

main $1

ping6 -c 1 fc00:100::1 || true

ping -c 3 10.10.200.1
exit 0
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend the existing tests for ipv4 ipv6 erspan version 2.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to support for ipv4 erspan, this patch adds
erspan v2 to ip6erspan tunnel.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch adds support for erspan version 2.  Not all features are
supported in this patch.  The SGT (security group tag), GRA (timestamp
granularity), FT (frame type) are set to fixed value.  Only hardware
ID and direction are configurable.  Optional subheader is also not
supported.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch refactors the existing erspan implementation in order
to support erspan version 2, which has additional metadata.  So, in
stead of having one 'struct erspanhdr' holding erspan version 1,
breaks it into 'struct erspan_base_hdr' and 'struct erspan_metadata'.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
nfp: ethtool flash updates

Dirk says:

This series adds the ability to update the control FW with ethtool.

It should be noted that the locking scheme here is to release the RTNL
lock before the flashing operation and to take it again afterwards to
ensure consistent state from the core code point of view. In this time,
we take a reference to the device to prevent the device being freed
while its being flashed.

This provides protection for the device being flashed while at the same
time not holding up any networking related functions which would
otherwise be locked out due to RTNL being held.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Firmware flashing takes around 60s (specified to not take more than
70s). Prevent hogging the RTNL lock in this time and make use of the
longer timeout for the NSP command. The timeout is set to 2.5 * 70
seconds.

We only allow flashing the firmware from reprs or PF netdevs. VFs do not
have an app reference.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The firmware flashing NSP operation takes longer to execute than the
current default timeout. We need a mechanism to set a longer timeout for
some commands. This patch adds the infrastructure to this.

The default timeout is still 30 seconds.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mahesh Bandewar says:

====================
ipvlan: packet scrub

While crossing namespace boundary IPvlan aggressively scrubs packets.
This is creating problems. First thing is that scrubbing changes the
packet type in skb meta-data to PACKET_HOST. This causes erroneous
packet delivery when dev_forward_skb() has already marked the packet
type as OTHER_HOST.

On the egress side scrubbing just before calling dev_queue_xmit()
creates another set of problems. Scrubbing remove skb->sk so the
prio update gets missed and more seriously, socket back-pressure
fails making TSQ not function correctly.

The first patch in the series just reverts the earlier change which
was adding a mac-check, but that is unnecessary if packet_type that
dev_forward_skb() has set is honored. The second path removes two of
the scrubs which are causing problems described above.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

IPvlan currently scrubs packets at every location where packets may be
crossing namespace boundary. Though this is desirable, currently IPvlan
does it more than necessary. e.g. packets that are going to take
dev_forward_skb() path will get scrubbed so no point in scrubbing them
before forwarding. Another side-effect of scrubbing is that pkt-type gets
set to PACKET_HOST which overrides what was already been set by the
earlier path making erroneous delivery of the packets.

Also scrubbing packets just before calling dev_queue_xmit() has detrimental
effects since packets lose skb->sk and because of that miss prio updates,
incorrect socket back-pressure and would even break TSQ.

Fixes: b93dd49c ('ipvlan: Scrub skb before crossing the namespace boundary')
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 92ff4264.

Even though the check added is not that taxing, it's not really needed.
First of all this will be per packet cost and second thing is that the
eth_type_trans() already does this correctly. The excessive scrubbing
in IPvlan was changing the pkt-type skb metadata of the packet which
made it necessary to re-check the mac. The subsequent patch in this
series removes the faulty packet-scrub.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net-next): ipsec-next 2017-12-15

1) Currently we can add or update socket policies, but
   not clear them. Support clearing of socket policies
   too. From Lorenzo Colitti.

2) Add documentation for the xfrm device offload api.
   From Shannon Nelson.

3) Fix IPsec extended sequence numbers (ESN) for
   IPsec offloading. From Yossef Efraim.

4) xfrm_dev_state_add function returns success even for
   unsupported options, fix this to fail in such cases.
   From Yossef Efraim.

5) Remove a redundant xfrm_state assignment.
   From Aviv Heller.

Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Update the compatible string and Device Tree binding document for
7278B0.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Salil Mehta says:

====================
Hisilicon Network Subsystem 3 VF Ethernet Driver

This patch-set contains the support of the HNS3 (Hisilicon Network Subsystem 3)
Virtual Function Ethernet driver for hip08 family of SoCs. The Physical Function
driver is already part of the Linux mainline.

This VF driver has its Hardware Compatibility Layer and has commom/unified ENET
layer/client/ethtool code with the PF driver. It also has support of mailbox to
communicate with the HNS3 PF driver. The basic architecture of VF driver is
derivative of the PF driver. Just like PF driver, this driver is also PCI
Express based.

This driver is the ongoing development work and HNS3 VF Ethernet driver would be
incrementally enhanced with more new features.

High Level Architecture:

                     [ Ethtool ]
	                 |
                 [ Ethernet Client ] ... [ RoCE Client ]
                         |                     |
                   [ HNAE Device ]             |________
                         |                     |       |
    ---------------------------------------------      |
                                                       |
     [ HNAE3 Framework (Register/unregister) ]         |
                                                       |
    ---------------------------------------------      |
                         |                             |
                 [ VF HCLGE Layer ]                    |
                  |             |                      |
                  |             |                      |
                  |             |                      |
                  |     [ VF Mailbox (To PF via IMP) ] |
                  |             |                      |
             [ IMP command Interface ]  [ IMP command Interface ]
                        |                              |
                        |                              |
           (A B O V E  R U N S  O N  G U E S T  S Y S T E M)
    -------------------------------------------------------------
              Q E M U / V F I O / K V M (on Host System)
    -------------------------------------------------------------
            HIP08  H A R D W A R E (limited to VF by SMMU)

   [ IMP/Mgmt Processor (hardware common to system/cmd based) ]

                Fig 1.   HNS3 Virtual Function Driver

    	[ dcbnl ]  [ Ethtool ]
            |          |
   	[  Ethernet Client  ]  [ ODP/UIO Client ] . . .[ RoCE Client ]
              |_____________________|                 |
                         |                   _________|
                   [ HNAE Device ]           |        |
                         |                   |        |
    ---------------------------------------------     |
                                                      |
     [ HNAE3 Framework (Register/unregister) ]        |
                                                      |
    ---------------------------------------------     |
                         |                            |
                  [ HCLGE Layer ]                     |
         ________________|_________________           |
        |                |                 |          |
     [ DCB ]             |                 |          |
        |                |                 |          |
  [ Scheduler/Shaper ] [ MDIO ]      [ PF Mailbox ]   |
        |                |                 |          |
        |________________|_________________|          |
                         |                            |
             [ IMP command Interface ]     [ IMP command Interface ]
    ----------------------------------------------------------------
              HIP08  H A R D W A R E

  [ IMP/Mgmt Processor (hardware common to system/cmd based) ]

               Fig 2.    Existing HNS3 PF Driver (added with mailbox)

Change Log Summary:
Patch V4: Addressed SPDX related comment by Philippe Ombredanne
Patch V3: Addressed SPDX change requested by Philippe Ombredanne
Patch V2: 1. Addressed some comments by David Miller.
	  2. Addressed some internal comments on various patches
Patch V1: Initial Submit
====================
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All PF mailbox events are conveyed through a common interrupt
(vector 0). This interrupt vector is shared by reset and mailbox.

This patch adds the handling of mailbox interrupt event and its
deferred processing in context to a separate mailbox task.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is required to support ring-vector binding and reset
of TQPs requested by the VF driver to the PF driver. Mailbox
handler is added with corresponding VF commands/messages to
handle the request.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Command queue provides the provision of Mailbox command which
can be used for communication between PF and VF. PF handles
messages from various VFs for fetching various information like,
queue, vlan, link status related etc. It also handles the request
from various VFs to perform certain privileged operations.

This patch adds the support of a message handler for handling
such various command requests from VF.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Most of the NAPI handling interface, skb buffer management,
management of the RX/TX descriptors, ethool interface etc.
has quite a bit of code which is common to VF and PF driver.

This patch makes the exisitng PF's HNS3 ENET driver as the
common ENET driver for both Virtual & Physical Function. This
will help in reduction of redundancy and better management of
code.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch introduces the new Makefiles and updates existing
Makefiles required to build the HNS3 Virtual Function driver.
This also updates the Kconfig for introduction of new menuconfig
entries related to VF driver.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the support of hardware compatibiltiy layer to the
HNS3 VF Driver. This layer implements various {set|get} operations
over MAC address for a virtual port, RSS related configuration,
fetches the link status info from PF, does various VLAN related
configuration over the virtual port, queries the statistics from
the hardware etc.

This layer can directly interact with hardware through the
IMP(Integrated Mangement Processor) interface or can use mailbox
to interact with the PF driver.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the support of the mailbox to the VF driver. The
mailbox shall be used as an interface to communicate with the
PF driver for various purposes like {set|get} MAC related
operations, reset, link status etc. The mailbox supports both
synchronous and asynchronous command send to PF driver.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support of command interface for communication with
the IMP(Integrated Management Processor) for HNS3 Virtual Function
Driver.

Each VF has support of CQP(Command Queue Pair) ring interface.
Each CQP consis of send queue CSQ and receive queue CRQ.
There are various commands a VF may support, like to query frimware
version, TQP management, statistics, interrupt related, mailbox etc.

This also contains code to initialize the command queue, manage the
command queue descriptors and Rx/Tx protocol with the command processor
in the form of various commands/results and acknowledgements.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sean Wang says:

====================
add VLAN support to DSA MT7530

Changes sicne v2:
update to the latest code base from net-next and fix up all building
errors with -Werror.

Changes since v1:
- fix up the typo
- prefer ordering declarations longest to shortest
- update that vlan_prepare callback should not change any state
- use lower case letter for function naming

The patchset extends DSA MT7530 to VLAN support through filling required
callbacks in patch 1 and merging the special tag with VLAN tag in patch 2
for allowing that the hardware can handle these packets with VID from the
CPU port.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

I work for MediaTek and maintain SoC targeting to home gateway and
also will keep extending and testing the function from MediaTek
switch.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to let MT7530 switch can recognize well those egress packets
having both special tag and VLAN tag, the information about the special
tag should be carried on the existing VLAN tag. On the other hand, it's
unnecessary for extra handling for ingress packets when VLAN tag is
present since it is able to put the VLAN tag after the special tag and
then follow the existing way to parse.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

MT7530 can treat each port as either VLAN-unaware port or VLAN-aware port
through the implementation of port matrix mode or port security mode on
the ingress port, respectively. On one hand, Each port has been acting as
the VLAN-unaware one whenever the device is created in the initial or
certain port joins or leaves into/from the bridge at the runtime. On the
other hand, the patch just filling the required callbacks for VLAN
operations is achieved via extending the port to be into port security
mode when the port is configured as VLAN-aware port. Which mode can make
the port be able to recognize VID from incoming packets and look up VLAN
table to validate and judge which port it should be going to. And the
range for VID from 1 to 4094 is valid for the hardware.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify lan9303_indirect_phy_wait_for_completion()
and lan9303_switch_wait_for_completion() by using a new function
lan9303_read_wait()

Changes v1 -> v2:
 - param 'mask' type u32
 - removed param 'value' (will probably never be used)
 - add newline before return
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stephen Hemminger says:

====================
hv_netvsc: minor changes

This includes minor cleanup of code in send and receive path and
also a new statistic to check for allocation failures. This also
eliminates some of the extra RCU when not needed.

There is a theoritical bug where buffered data could be blocked
for longer than necessary if the ring buffer got full. This
has not been seen in the wild, found by inspection.

The reference count between net device and internal RNDIS
is not needed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If the transmit queue is known full, then don't keep aggregating
data. And the cp_partial flag which indicates that the current
aggregation buffer is full can be folded in to avoid more
conditionals.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is only ever a single instance of network device object
referencing the internal rndis object. Therefore the open_cnt atomic
is not necessary.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The netvsc_receive_callback function was using RCU to find the
appropriate underlying netvsc_device. Since calling function already
had that pointer, this was unnecessary.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The caller (netvsc_receive) already has the net device pointer,
and should just pass that to functions rather than the hyperv device.
This eliminates several impossible error paths in the process.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When skb can not be allocated, update ethtool statisitics
rather than rx_dropped which is intended for netif_receive.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>