Add a new tx_resets ring counter.  This counter will be saved as
tx_total_resets across any reset.  Since we currently do a full reset
in bnxt_sched_reset_txr(), the per ring counter will always be cleared
during reset.  Only the tx_total_resets count will be meaningful and we
only display this under ethtool -S.

Link: https://lore.kernel.org/netdev/CACKFLimD-bKmJ1tGZOLYRjWzEwxkri-Mw7iFme1x2Dr0twdCeg@mail.gmail.com/Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230817231911.165035-7-michael.chan@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The existing driver displays the sum of 4 ring counters under ethtool -S.
These counters are in the array bnxt_sw_func_stats.  These counters are
summed at the time of ethtool -S and will be lost when the device is reset.

Replace these counters with the new total ring error counters added in the
last patch.  These new counters are saved before reset.  ethtool -S will
now display the sum of the saved counters plus the current counters.

Link: https://lore.kernel.org/netdev/CACKFLimD-bKmJ1tGZOLYRjWzEwxkri-Mw7iFme1x2Dr0twdCeg@mail.gmail.com/Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230817231911.165035-6-michael.chan@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Currently, the ring counters are stored in the per ring datastructure.
During reset, all the rings are freed together with the associated
datastructures.  As a result, all the ring error counters will be reset
to zero.

Add logic to keep track of the total error counts of all the rings
and save them before reset (including ifdown).  The next patch will
display these total ring error counters under ethtool -S.

Link: https://lore.kernel.org/netdev/CACKFLimD-bKmJ1tGZOLYRjWzEwxkri-Mw7iFme1x2Dr0twdCeg@mail.gmail.com/Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230817231911.165035-5-michael.chan@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

If we are doing a complete reset with irq_re_init set to true in
bnxt_close_nic(), all the ring structures will be freed.  New
structures will be allocated in bnxt_open_nic().  The current code
increments rx_resets counter in bnxt_enable_napi() if bnapi->in_reset
is true.  In a complete reset, bnapi->in_reset will never be true
since the structure is just allocated.

Increment the rx_resets counter in bnxt_disable_napi() instead.  This
will allow us to save all the ring error counters including the
rx_resets counters in the next patch.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230817231911.165035-4-michael.chan@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Use the page pool's ability to maintain DMA mappings for us.
This avoids re-mapping of the recycled pages.

Link: https://lore.kernel.org/netdev/20230728231829.235716-4-michael.chan@broadcom.com/Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230817231911.165035-3-michael.chan@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Convert to use the page pool buffers for the aggregation ring when
running in non-XDP mode.  This simplifies the driver and we benefit
from the recycling of pages.  Adjust the page pool size to account
for the aggregation ring size.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230817231911.165035-2-michael.chan@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2023-08-17 (ice)

This series contains updates to ice driver only.

Jan removes unused functions and refactors code to make, possible,
functions static.

Jake rearranges some functions to be logically grouped.

Marcin removes an unnecessary call to disable VLAN stripping.

Yang Yingliang utilizes list_for_each_entry() helper for a couple list
traversals.

Przemek removes some parameters from ice_aq_alloc_free_res() which were
always the same and reworks ice_aq_wait_for_event() to reduce chance of
race.

* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
  ice: split ice_aq_wait_for_event() func into two
  ice: embed &ice_rq_event_info event into struct ice_aq_task
  ice: ice_aq_check_events: fix off-by-one check when filling buffer
  ice: drop two params from ice_aq_alloc_free_res()
  ice: use list_for_each_entry() helper
  ice: Remove redundant VSI configuration in eswitch setup
  ice: move E810T functions to before device agnostic ones
  ice: refactor ice_vsi_is_vlan_pruning_ena
  ice: refactor ice_ptp_hw to make functions static
  ice: refactor ice_sched to make functions static
  ice: Utilize assign_bit() helper
  ice: refactor ice_vf_lib to make functions static
  ice: refactor ice_lib to make functions static
  ice: refactor ice_ddp to make functions static
  ice: remove unused methods
====================

Link: https://lore.kernel.org/r/20230817212239.2601543-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Return PTR_ERR_OR_ZERO() instead of return 0 or PTR_ERR() to
simplify code.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230817022418.3588831-1-ruanjinjie@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Since debugfs_create_dir() returns ERR_PTR, IS_ERR() is enough to
check whether the directory is successfully created. So remove the
redundant NULL check.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230817073017.350002-1-ruanjinjie@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

do_pci_disable_device() disable PCI bus-mastering as following:
static void do_pci_disable_device(struct pci_dev *dev)
{
		u16 pci_command;

		pci_read_config_word(dev, PCI_COMMAND, &pci_command);
		if (pci_command & PCI_COMMAND_MASTER) {
				pci_command &= ~PCI_COMMAND_MASTER;
				pci_write_config_word(dev, PCI_COMMAND, pci_command);
		}

		pcibios_disable_device(dev);
}
And pci_disable_device() sets dev->is_busmaster to 0.

pci_enable_device() is called only once before calling to
pci_disable_device() and such pci_clear_master() is not needed. So remove
redundant pci_clear_master().

Also rename goto label 'err_out_clear_master' to 'err_out_disable_device'.
Signed-off-by: Yu Liao <liaoyu15@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20230817025709.2023553-1-liaoyu15@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Tony Nguyen says:

====================
virtchnl: fix fake 1-elem arrays

Alexander Lobakin says:

6.5-rc1 started spitting warning splats when composing virtchnl
messages, precisely on virtchnl_rss_key and virtchnl_lut:

[   84.167709] memcpy: detected field-spanning write (size 52) of single
field "vrk->key" at drivers/net/ethernet/intel/iavf/iavf_virtchnl.c:1095
(size 1)
[   84.169915] WARNING: CPU: 3 PID: 11 at drivers/net/ethernet/intel/
iavf/iavf_virtchnl.c:1095 iavf_set_rss_key+0x123/0x140 [iavf]
...
[   84.191982] Call Trace:
[   84.192439]  <TASK>
[   84.192900]  ? __warn+0xc9/0x1a0
[   84.193353]  ? iavf_set_rss_key+0x123/0x140 [iavf]
[   84.193818]  ? report_bug+0x12c/0x1b0
[   84.194266]  ? handle_bug+0x42/0x70
[   84.194714]  ? exc_invalid_op+0x1a/0x50
[   84.195149]  ? asm_exc_invalid_op+0x1a/0x20
[   84.195592]  ? iavf_set_rss_key+0x123/0x140 [iavf]
[   84.196033]  iavf_watchdog_task+0xb0c/0xe00 [iavf]
...
[   84.225476] memcpy: detected field-spanning write (size 64) of single
field "vrl->lut" at drivers/net/ethernet/intel/iavf/iavf_virtchnl.c:1127
(size 1)
[   84.227190] WARNING: CPU: 27 PID: 1044 at drivers/net/ethernet/intel/
iavf/iavf_virtchnl.c:1127 iavf_set_rss_lut+0x123/0x140 [iavf]
...
[   84.246601] Call Trace:
[   84.247228]  <TASK>
[   84.247840]  ? __warn+0xc9/0x1a0
[   84.248263]  ? iavf_set_rss_lut+0x123/0x140 [iavf]
[   84.248698]  ? report_bug+0x12c/0x1b0
[   84.249122]  ? handle_bug+0x42/0x70
[   84.249549]  ? exc_invalid_op+0x1a/0x50
[   84.249970]  ? asm_exc_invalid_op+0x1a/0x20
[   84.250390]  ? iavf_set_rss_lut+0x123/0x140 [iavf]
[   84.250820]  iavf_watchdog_task+0xb16/0xe00 [iavf]

Gustavo already tried to fix those back in 2021[0][1]. Unfortunately,
a VM can run a different kernel than the host, meaning that those
structures are sorta ABI.
However, it is possible to have proper flex arrays + struct_size()
calculations and still send the very same messages with the same sizes.
The common rule is:

elem[1] -> elem[]
size = struct_size() + <difference between the old and the new msg size>

The "old" size in the current code is calculated 3 different ways for
10 virtchnl structures total. Each commit addresses one of the ways
cumulatively instead of per-structure.

I was planning to send it to -net initially, but given that virtchnl was
renamed from i40evf and got some fat style cleanup commits in the past,
it's not very straightforward to even pick appropriate SHAs, not
speaking of automatic portability. I may send manual backports for
a couple of the latest supported kernels later on if anyone needs it
at all.

[0] https://lore.kernel.org/all/20210525230912.GA175802@embeddedor
[1] https://lore.kernel.org/all/20210525231851.GA176647@embeddedor

* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
  virtchnl: fix fake 1-elem arrays for structures allocated as `nents`
  virtchnl: fix fake 1-elem arrays in structures allocated as `nents + 1`
  virtchnl: fix fake 1-elem arrays in structs allocated as `nents + 1` - 1
====================

Link: https://lore.kernel.org/r/20230816210657.1326772-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Simon Wunderlich says:

====================
This cleanup patchset includes the following patches:

 - bump version strings, by Simon Wunderlich

 - Remove unused declarations, by Yue Haibing

 - Clean up MTU handling, by Sven Eckelmann (2 patches)

 - Clean up/remove (obsolete) functions, by Sven Eckelmann (3 patches)

* tag 'batadv-next-pullrequest-20230816' of git://git.open-mesh.org/linux-merge:
  batman-adv: Drop per algo GW section class code
  batman-adv: Keep batadv_netlink_notify_* static
  batman-adv: Drop unused function batadv_gw_bandwidth_set
  batman-adv: Check hardif MTU against runtime MTU
  batman-adv: Avoid magic value for minimum MTU
  batman-adv: Remove unused declarations
  batman-adv: Start new development cycle
====================

Link: https://lore.kernel.org/r/20230816164000.190884-1-sw@simonwunderlich.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Now that the "budget" is passed into fec_enet_tx_queue(), one
optimization we can do is to use napi_consume_skb() to instead
of dev_kfree_skb_any().
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Suggested-by: Alexander H Duyck <alexander.duyck@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230816090242.463822-1-wei.fang@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

./drivers/net/ethernet/sfc/tc_conntrack.c:464:2-3: Unneeded semicolon
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20230816004944.10841-1-yang.lee@linux.alibaba.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Since v6.5-rc1 MM-tree is merged and contains a new flag SLAB_NO_MERGE
in commit d0bf7d57 ("mm/slab: introduce kmem_cache flag SLAB_NO_MERGE")
now is the time to use this flag for networking as proposed
earlier see link.

The SKB (sk_buff) kmem_cache slab is critical for network performance.
Network stack uses kmem_cache_{alloc,free}_bulk APIs to gain
performance by amortising the alloc/free cost.

For the bulk API to perform efficiently the slub fragmentation need to
be low. Especially for the SLUB allocator, the efficiency of bulk free
API depend on objects belonging to the same slab (page).

When running different network performance microbenchmarks, I started
to notice that performance was reduced (slightly) when machines had
longer uptimes. I believe the cause was 'skbuff_head_cache' got
aliased/merged into the general slub for 256 bytes sized objects (with
my kernel config, without CONFIG_HARDENED_USERCOPY).

For SKB kmem_cache network stack have other various reasons for
not merging, but it varies depending on kernel config (e.g.
CONFIG_HARDENED_USERCOPY). We want to explicitly set SLAB_NO_MERGE
for this kmem_cache to get most out of kmem_cache_{alloc,free}_bulk APIs.

When CONFIG_SLUB_TINY is configured the bulk APIs are essentially
disabled. Thus, for this case drop the SLAB_NO_MERGE flag.

Link: https://lore.kernel.org/all/167396280045.539803.7540459812377220500.stgit@firesoul/Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Link: https://lore.kernel.org/r/169211265663.1491038.8580163757548985946.stgit@firesoulSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Cross-merge networking fixes after downstream PR.

Conflicts:

drivers/net/ethernet/sfc/tc.c
  fa165e19 ("sfc: don't unregister flow_indr if it was never registered")
  3bf969e8 ("sfc: add MAE table machinery for conntrack table")
https://lore.kernel.org/all/20230818112159.7430e9b4@canb.auug.org.au/

No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Jakub Kicinski:
 "Including fixes from ipsec and netfilter.

  No known outstanding regressions.

  Fixes to fixes:

   - virtio-net: set queues after driver_ok, avoid a potential race
     added by recent fix

   - Revert "vlan: Fix VLAN 0 memory leak", it may lead to a warning
     when VLAN 0 is registered explicitly

   - nf_tables:
      - fix false-positive lockdep splat in recent fixes
      - don't fail inserts if duplicate has expired (fix test failures)
      - fix races between garbage collection and netns dismantle

  Current release - new code bugs:

   - mlx5: Fix mlx5_cmd_update_root_ft() error flow

  Previous releases - regressions:

   - phy: fix IRQ-based wake-on-lan over hibernate / power off

  Previous releases - always broken:

   - sock: fix misuse of sk_under_memory_pressure() preventing system
     from exiting global TCP memory pressure if a single cgroup is under
     pressure

   - fix the RTO timer retransmitting skb every 1ms if linear option is
     enabled

   - af_key: fix sadb_x_filter validation, amment netlink policy

   - ipsec: fix slab-use-after-free in decode_session6()

   - macb: in ZynqMP resume always configure PS GTR for non-wakeup
     source

  Misc:

   - netfilter: set default timeout to 3 secs for sctp shutdown send and
     recv state (from 300ms), align with protocol timers"

* tag 'net-6.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (49 commits)
  ice: Block switchdev mode when ADQ is active and vice versa
  qede: fix firmware halt over suspend and resume
  net: do not allow gso_size to be set to GSO_BY_FRAGS
  sock: Fix misuse of sk_under_memory_pressure()
  sfc: don't fail probe if MAE/TC setup fails
  sfc: don't unregister flow_indr if it was never registered
  net: dsa: mv88e6xxx: Wait for EEPROM done before HW reset
  net/mlx5: Fix mlx5_cmd_update_root_ft() error flow
  net/mlx5e: XDP, Fix fifo overrun on XDP_REDIRECT
  i40e: fix misleading debug logs
  iavf: fix FDIR rule fields masks validation
  ipv6: fix indentation of a config attribute
  mailmap: add entries for Simon Horman
  broadcom: b44: Use b44_writephy() return value
  net: openvswitch: reject negative ifindex
  team: Fix incorrect deletion of ETH_P_8021AD protocol vid from slaves
  net: phy: broadcom: stub c45 read/write for 54810
  netfilter: nft_dynset: disallow object maps
  netfilter: nf_tables: GC transaction race with netns dismantle
  netfilter: nf_tables: fix GC transaction races with netns and netlink event exit path
  ...

Pull drm fixes from Dave Airlie:
 "Regular enough week, mostly the usual amdgpu and i915 fixes.  Also
  qaic, nouveau, qxl and a revert for an EDID patch that had some side
  effects, along with a couple of panel fixes.

  edid:
   - revert mode parsing fix that had side effects.

  i915:
   - Fix the flow for ignoring GuC SLPC efficient frequency selection
   - Fix SDVO panel_type initialization
   - Fix display probe for IVB Q and IVB D GT2 server

  nouveau:
   - fix use-after-free in connector code

  qaic:
   - integer overflow check fix
   - fix slicing memory leak

  panel:
   - fix JDI LT070ME05000 probing
   - fix AUO G121EAN01 timings

  amdgpu:
   - SMU 13.x fixes
   - Fix mcbp parameter for gfx9
   - SMU 11.x fixes
   - Temporary fix for large numbers of XCP partitions
   - S0ix fixes
   - DCN 2.0 fix

  qxl:
   - fix use after free race in dumb object allocation"

* tag 'drm-fixes-2023-08-18-1' of git://anongit.freedesktop.org/drm/drm:
  drm/qxl: fix UAF on handle creation
  Revert "drm/edid: Fix csync detailed mode parsing"
  drm/nouveau/disp: fix use-after-free in error handling of nouveau_connector_create
  Revert "Revert "drm/amdgpu/display: change pipe policy for DCN 2.0""
  drm/amd: flush any delayed gfxoff on suspend entry
  drm/amdgpu: skip fence GFX interrupts disable/enable for S0ix
  drm/amdgpu: skip xcp drm device allocation when out of drm resource
  drm/amd/pm: Update pci link width for smu v13.0.6
  drm/amd/pm: Fix temperature unit of SMU v13.0.6
  drm/amdgpu/pm: fix throttle_status for other than MP1 11.0.7
  drm/amdgpu: disable mcbp if parameter zero is set
  drm/amd/pm: disallow the fan setting if there is no fan on smu 13.0.0
  accel/qaic: Clean up integer overflow checking in map_user_pages()
  accel/qaic: Fix slicing memory leak
  drm/i915: fix display probe for IVB Q and IVB D GT2 server
  drm/i915/sdvo: fix panel_type initialization
  drm/i915/guc/slpc: Restore efficient freq earlier
  drm/panel: simple: Fix AUO G121EAN01 panel timings according to the docs
  drm/panel: JDI LT070ME05000 simplify with dev_err_probe()

Breno Leitao says:

====================
netconsole: Enable compile time configuration

Enable netconsole features to be set at compilation time. Create two
Kconfig options that allow users to set extended logs and release
prepending features at compilation time.

The first patch de-duplicates the initialization code, and the second
patch adds the support in the de-duplicated code, avoiding touching two
different functions with the same change.
====================

Link: https://lore.kernel.org/r/20230811093158.1678322-1-leitao@debian.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Enable netconsole features to be set at compilation time. Create two
Kconfig options that allow users to set extended logs and release
prepending features at compilation time.

Right now, the user needs to pass command line parameters to netconsole,
such as "+"/"r" to enable extended logs and version prepending features.

With these two options, the user could set the default values for the
features at compile time, and don't need to pass it in the command line
to get them enabled, simplifying the command line.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230811093158.1678322-3-leitao@debian.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

De-duplicate the initialization and allocation code for struct
netconsole_target.

The same allocation and initialization code is duplicated in two
different places in the netconsole subsystem, when the netconsole target
is initialized by command line parameters (alloc_param_target()), and
dynamically by sysfs (make_netconsole_target()).

Create a helper function, and call it from the two different functions.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230811093158.1678322-2-leitao@debian.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When building with clang 18 I see the following warning:
|       drivers/net/mdio/mdio-xgene.c:338:13: warning: cast to smaller integer
|               type 'enum xgene_mdio_id' from 'const void *' [-Wvoid-pointer-to-enum-cast]
|         338 |                 mdio_id = (enum xgene_mdio_id)of_id->data;

This is due to the fact that `of_id->data` is a void* while `enum
xgene_mdio_id` has the size of an int. This leads to truncation and
possible data loss.

Link: https://github.com/ClangBuiltLinux/linux/issues/1910Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20230815-void-drivers-net-mdio-mdio-xgene-v1-1-5304342e0659@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

François Michel says:

====================
netem: use a seeded PRNG for loss and corruption events

In order to reproduce bugs or performance evaluation of
network protocols and applications, it is useful to have
reproducible test suites and tools. This patch adds
a way to specify a PRNG seed through the
TCA_NETEM_PRNG_SEED attribute for generating netem
loss and corruption events. Initializing the qdisc
with the same seed leads to the exact same loss
and corruption patterns. If no seed is explicitly
specified, the qdisc generates a random seed using
get_random_u64().

This patch can be and has been tested using tc from
the following iproute2-next fork:
https://github.com/francoismichel/iproute2-next

For instance, setting the seed 42424242 on the loopback
with a loss rate of 10% will systematically drop the 5th,
12th and 24th packet when sending 25 packets.
====================

Link: https://lore.kernel.org/r/20230815092348.1449179-1-francois.michel@uclouvain.beSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Use prandom_u32_state() instead of get_random_u32() to generate
the correlated loss events of netem.
Signed-off-by: François Michel <francois.michel@uclouvain.be>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Link: https://lore.kernel.org/r/20230815092348.1449179-4-francois.michel@uclouvain.beSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Use prandom_u32_state() instead of get_random_u32() to generate
the random loss events of netem. The state of the prng is part
of the prng attribute of struct netem_sched_data.
Signed-off-by: François Michel <francois.michel@uclouvain.be>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Link: https://lore.kernel.org/r/20230815092348.1449179-3-francois.michel@uclouvain.beSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add prng attribute to struct netem_sched_data and
allows setting the seed of the PRNG through netlink
using the new TCA_NETEM_PRNG_SEED attribute.
The PRNG attribute is not actually used yet.
Signed-off-by: François Michel <francois.michel@uclouvain.be>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Link: https://lore.kernel.org/r/20230815092348.1449179-2-francois.michel@uclouvain.beSigned-off-by: Jakub Kicinski <kuba@kernel.org>

PCI core API pci_dev_id() can be used to get the BDF number for a pci
device. We don't need to compose it manually. Use pci_dev_id() to
simplify the code a little bit.
Signed-off-by: Jialin Zhang <zhangjialin11@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Shay Agroskin <shayagr@amazon.com>
Link: https://lore.kernel.org/r/20230815024248.3519068-1-zhangjialin11@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add missing __exit annotations to module exit func tun_cleanup().
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230814083000.3893589-1-william.xuanziyang@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2023-08-16 (iavf, i40e)

This series contains updates to iavf and i40e drivers.

Piotr adds checks for unsupported Flow Director rules on iavf.

Andrii replaces incorrect 'write' messaging on read operations for i40e.

* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
  i40e: fix misleading debug logs
  iavf: fix FDIR rule fields masks validation
====================

Link: https://lore.kernel.org/r/20230816193308.1307535-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Mitigate race between registering on wait list and receiving
AQ Response from FW.

ice_aq_prep_for_event() should be called before sending AQ command,
ice_aq_wait_for_event() should be called after sending AQ command,
to wait for AQ Response.

Please note, that this was found by reading the code,
an actual race has not yet materialized.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Expose struct ice_aq_task to callers,
what takes burden of memory ownership out from AQ-wait family of functions,
and reduces need for heap-based allocations.

Embed struct ice_rq_event_info event into struct ice_aq_task
(instead of it being a ptr) to remove some more code from the callers.

Subsequent commit will improve more based on this one.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Allow task's event buffer to be filled also in the case that it's size
is exactly the size of the message.

Fixes: d69ea414 ("ice: implement device flash update via devlink")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Drop @num_entries and @cd params, latter of which was always NULL.

Number of entities to alloc is passed in internal buffer, the outer layer
(that @num_entries was assigned to) meaning is closer to "the number of
requests", which was =1 in all cases.
ice_free_hw_res() was always called with 1 as its @num arg.
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Convert list_for_each() to list_for_each_entry() where applicable.
No functional changed.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Remove a call to disable VLAN stripping on switchdev control plane VSI, as
it is disabled by default.
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Commit 885fe693 ("ice: Add support for SMA control multiplexer")
accidentally placed all of the E810T SMA control functions in the middle of
the device agnostic functions section of ice_ptp_hw.c

This works fine, but makes it harder for readers to follow. The
ice_ptp_hw.c file is laid out such that each hardware family has the
specific functions in one block, with the access functions placed at the
end of the file.

Move the E810T functions so that they are in a block just after the E810
functions. Also move the ice_get_phy_tx_tstamp_ready_e810 which got added
at the end of the E810T block.

This keeps the functions laid out in a logical order and avoids intermixing
the generic access functions with the device specific implementations.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

As this method became static, and is already called
with check for vsi being non-null, an unnecessary check along
with superfluous parentheses is removed.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

As following methods are not used outside ice_ptp_hw,
they can be made static:
ice_read_phy_reg_e822
ice_write_phy_reg_e822
ice_ptp_prep_port_adj_e822
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

As ice_sched_set_node_bw_lmt_per_tc is not used
outside of ice_sched, it can be made static.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The if/else check for bit setting can be replaced by using the
assign_bit() helper so do so.
Suggested-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>