BACO dummy mode could be set under reset conditions and that affects
framebuffer access. Check If baco dummy mode is set, unset it if so.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Tested-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
If VBlank_nom is too small, it will cause
VStartUP_Start smaller than VBackPorch + VSync width which is an
invalid case for VStartUP_Start and where to send AS-SDP.

[How]
Setup a minimum value to VBlank_nom
Reviewed-by: Reza Amini <reza.amini@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: ChunTao Tso <chuntao.tso@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
vstartup is calculated to be a large number. it works because
it is within vertical blank, but it reduces region of blank that
can be used for power gating.

[how]
Calculation needs to convert micro seconds to number of
vertical lines.
Reviewed-by: Kazlauskas Nicholas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Reza Amini <reza.amini@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[why]
This Unit correction exposes a Replay corruption.

[how]
This reverts commit:
commit dbd29029 ("drm/amd/display: Correct unit conversion for vstartup")

Roll back unit conversion until Replay can fix their corruption.

Fixes: dbd29029 ("drm/amd/display: Correct unit conversion for vstartup")
Reviewed-by: Reza Amini <reza.amini@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Enable ras for mp0 v13_0_6 sriov
Signed-off-by: YiPeng Chai <YiPeng.Chai@amd.com>
Reviewed-by: Stanley.Yang <Stanley.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

if hmm_range_get_pages returns EBUSY error during
svm_range_validate_and_map, within the context of a page fault
interrupt. This should retry through svm_range_restore_pages
callback. Therefore we treat this as EAGAIN error instead, and defer
it to restore pages fallback.
Signed-off-by: Alex Sierra <alex.sierra@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Powergating is handled in the host driver.
Reviewed-by: Zhigang Luo <zhigang.luo@amd.com>
Signed-off-by: Samir Dhume <samir.dhume@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Add critical temperature message support func for smu v13.0.6
and expose critical temperature as part of hw mon attributes
for GC v9.4.3

v2:
Added comment for pmfw version requirement & move the check
to get_thermal_temperature_range function
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Update PMFW interface headers for updated metrics table and
critical temperature message
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Several new fields are exposed in gc_info v2_1
Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Shiwu Zhang <shiwu.zhang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Mall info v2 is introduced in ip discovery
Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Shiwu Zhang <shiwu.zhang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

RAS EEPROM device is only supported on dGPU platform for smu v13_0_6.
Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

7957ec80 ("drm/amdgpu: Add FRU sysfs nodes only if needed") moved
the documentation for some of the sysfs nodes to amdgpu_fru_eeprom.c.
Update the documentation accordingly.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

- There is a DPM issue where if DC is not present,
  FCLK will stay at low level.
  We need to send a SMU message to configure the DPM

- Reuse smu_v13_0_notify_display_change() for this purpose
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Bokun Zhang <bokun.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

- Setup replay config on device init.
- Enable replay if feature is enabled (prioritize replay over PSR, since
it can be enabled in more usecases)
- Add debug masks to enable replay on supported ASICs
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Merge tag 'drm-intel-next-fixes-2023-08-24' of git://anongit.freedesktop.org/drm/drm-intel into drm-next

- Fix TLB invalidation (Alan)
- Fix Display HPD polling (Imre)
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZOdOP31OE/Cf1ojo@intel.com

Merge tag 'drm-misc-next-fixes-2023-08-24' of git://anongit.freedesktop.org/drm/drm-misc into drm-next

Short summary of fixes pull:

 * gpuva: Cleanups

 * kunit: Documentation fixes

 * nouveau:
   * UAPI: Avoid implicit NO_PREFETCH flag
   * Scheduler fixes
   * Fix remap

 * ttm: Fix type conversion in tests
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230824181241.GA6386@linux-uq9g.hotspot.internet-for-guests.com

The prev pointer in __drm_gpuva_sm_map() was used to implement automatic
merging of mappings. Since automatic merging did not make its way
upstream, remove this leftover.

Fixes: e6303f32 ("drm: manager to keep track of GPUs VA mappings")
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230823233119.2891-1-dakr@redhat.com

Fixes the following W=1 kernel build warning(s):

 drivers/gpu/drm/tests/drm_kunit_helpers.c:172: warning: expecting prototype for drm_kunit_helper_context_alloc(). Prototype was for drm_kunit_helper_acquire_ctx_alloc() instead
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230824073710.2677348-10-lee@kernel.org
Link: https://lore.kernel.org/r/20230824073710.2677348-14-lee@kernel.org
[mripard: Squashed the two patches together]
Signed-off-by: Maxime Ripard <mripard@kernel.org>

Currently, NO_PREFETCH is passed implicitly through
drm_nouveau_gem_pushbuf_push::length and drm_nouveau_exec_push::va_len.

Since this is a direct representation of how the HW is programmed it
isn't really future proof for a uAPI. Hence, fix this up for the new
uAPI and split up the va_len field of struct drm_nouveau_exec_push,
such that we keep 32bit for va_len and 32bit for flags.

For drm_nouveau_gem_pushbuf_push::length at least provide
NOUVEAU_GEM_PUSHBUF_NO_PREFETCH to indicate the bit shift.

While at it, fix up nv50_dma_push() as well, such that the caller
doesn't need to encode the NO_PREFETCH flag into the length parameter.
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Faith Ekstrand <faith.ekstrand@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230823181746.3446-1-dakr@redhat.com

Transfer the region pointer of a uvma to the new uvma(s) on re-map to
prevent potential shader faults when the re-mapped uvma(s) are unmapped.
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230820222920.2344-1-dakr@redhat.com

If a sched job depends on a dma-fence from a job from the same GPU
scheduler instance, but a different scheduler entity, the GPU scheduler
does only wait for the particular job to be scheduled, rather than for
the job to fully complete. This is due to the GPU scheduler assuming
that there is a scheduler instance per ring. However, the current
implementation, in order to avoid arbitrary amounts of kthreads, has a
single scheduler instance while scheduler entities represent rings.

As a workaround, set the DRM_SCHED_FENCE_DONT_PIPELINE for all
out-fences in order to force the scheduler to wait for full job
completion for dependent jobs from different entities and same scheduler
instance.

There is some work in progress [1] to address the issues of firmware
schedulers; once it is in-tree the scheduler topology in Nouveau should
be re-worked accordingly.

[1] https://lore.kernel.org/dri-devel/20230801205103.627779-1-matthew.brost@intel.com/Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Faith Ekstrand <faith.ekstrand@collaboralcom>
Link: https://patchwork.freedesktop.org/patch/msgid/20230811010632.2473-1-dakr@redhat.com

Updates for v6.6, which includes a backmerge of msm-fixes to avoid conficts.

Core:
- SM6125 MDSS support

DPU:
- SM6125 DPU support
- Added subblocks to display snapshot
- Use UBWC data from MDSS driver rather than duplicating it
- dpu_core_perf cleanup

DSI:
- Enabled burst mode to fix CMD mode panels
- Runtime PM support
- refgen regulator support

DSI PHY:
- SM6125 support in 14nm DSI PHY driver

GPU:
- Rework GPU identification to prepare for a7xx, and other a7xx prep
- Cleanups and fixes
- Disallow legacy relocs on a6xx and newer
- a690: switch to using a660_gmu.bin fw as this is what we have in
  linux-firmware and we see no evidence that it should be different
  from other a660 family (a6xx subgen 4) devices
- Submit overhead opts, 1.6x faster for NO_IMPLICIT_SYNC commits with
  100 BOs to 2.5x faster for 1000 BOs
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGv_01g-edjdfKLWWcb-rO5aSyLsv5FpbKrTkXVL9+ngTQ@mail.gmail.com

Linux 6.5-rc7

This is needed for the CI stuff and the msm pull has fixes in it.
Signed-off-by: Dave Airlie <airlied@redhat.com>

After the commit in the Fixes: line below, HPD polling stopped working
on i915, since after that change calling drm_kms_helper_poll_enable()
doesn't restart drm_mode_config::output_poll_work if the work was
stopped (no connectors needing polling) and enabling polling for a
connector (during runtime suspend or detecting an HPD IRQ storm).

After the above change calling drm_kms_helper_poll_enable() is a nop
after it's been called already and polling for some connectors was
disabled/re-enabled.

Fix this by calling drm_kms_helper_poll_reschedule() added in the
previous patch instead, which reschedules the work whenever expected.

Fixes: d33a54e3 ("drm/probe_helper: sort out poll_running vs poll_enabled")
CC: stable@vger.kernel.org # 6.4+
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230822113015.41224-2-imre.deak@intel.com
(cherry picked from commit 50452f2f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

Add a helper to reschedule drm_mode_config::output_poll_work after
polling has been enabled for a connector (and needing a reschedule,
since previously polling was disabled for all connectors and hence
output_poll_work was not running).

This is needed by the next patch fixing HPD polling on i915.

CC: stable@vger.kernel.org # 6.4+
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230822113015.41224-1-imre.deak@intel.com
(cherry picked from commit fe2352fd)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

When getting the next gt's seqno to be stored into an
objects mm.tlb[gt_id] array, fix the retrieval code
to get it from the correct gt instead of the same one.

Fixes: d6c531ab ("drm/i915: Invalidate the TLBs on each GT")
Signed-off-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230814182449.1060747-1-alan.previn.teres.alexis@intel.com
(cherry picked from commit 90b8ad13)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>

Fix a warning about casting an integer of different size in
ttm_pool_alloc_basic_dma_addr() subtest. Cast the DMA address to
uintptr_t before casting it to a generic pointer.
Signed-off-by: Karolina Stolarek <karolina.stolarek@intel.com>
Cc: Christian König <christian.koenig@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202308150419.PaHfWntn-lkp@intel.com/
Link: https://patchwork.freedesktop.org/patch/msgid/20230816105508.1135410-1-karolina.stolarek@intel.comReviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>

amd-drm-next-6.6-2023-08-18:

amdgpu:
- Panel replay fixes
- Misc checkpatch fixes
- SMU 13.x fixes
- mcbp parameter handling fix for gfx9
- RAS fixes
- Misc code cleanups
- SR-IOV fixes
- Expose both current and average power via hwmon if supported
- DP retimer fix
- Clockgating fix
- Subvp fixes
- DMCUB fixes
- Gamut remap fix
- Misc display fixes
- Allow users to force runtime pm when displays are attached
- Gracefully handle more partitions than drm nodes
- S0ix fixes
- GC 9.4.3 fixes

amdkfd:
- TBA fix for aldebaran
- Fix build without CONFIG_DYNAMIC_DEBUG
- memdup cleanup
- Fix address watch clearing

radeon:
- Misc code cleanups
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230818195247.10981-1-alexander.deucher@amd.com

Merge tag 'drm-misc-next-fixes-2023-08-17' of git://anongit.freedesktop.org/drm/drm-misc into drm-next

Short summary of fixes pull:

 * Add MMU dependency to TTM unit tests
 * panel: Fix Innolux G156HCE-L01 LVDS clock
Signed-off-by: Dave Airlie <airlied@redhat.com>

From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230817131832.GA9361@linux-uq9g

Pull tty/serial fixes from Greg KH:
 "Here are some small tty and serial core fixes for 6.5-rc7 that resolve
  a lot of reported issues.

  Primarily in here are the fixes for the serial bus code from Tony that
  came in -rc1, as it hit wider testing with the huge number of
  different types of systems and serial ports. All of the reported
  issues with duplicate names and other issues with this code are now
  resolved.

  Other than that included in here is:

   - n_gsm fix for a previous fix

   - 8250 lockdep annotation fix

   - fsl_lpuart serial driver fix

   - TIOCSTI documentation update for previous CAP_SYS_ADMIN change

  All of these have been in linux-next for a while with no reported
  problems"

* tag 'tty-6.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: core: Fix serial core port id, including multiport devices
  serial: 8250: drop lockdep annotation from serial8250_clear_IER()
  tty: n_gsm: fix the UAF caused by race condition in gsm_cleanup_mux
  serial: core: Revert port_id use
  TIOCSTI: Document CAP_SYS_ADMIN behaviour in Kconfig
  serial: 8250: Fix oops for port->pm on uart_change_pm()
  serial: 8250: Reinit port_id when adding back serial8250_isa_devs
  serial: core: Fix kmemleak issue for serial core device remove
  MAINTAINERS: Merge TTY layer and serial drivers
  serial: core: Fix serial_base_match() after fixing controller port name
  serial: core: Fix serial core controller port name to show controller id
  serial: core: Fix serial core port id to not use port->line
  serial: core: Controller id cannot be negative
  tty: serial: fsl_lpuart: Clear the error flags by writing 1 for lpuart32 platforms

Pull rust fix from Miguel Ojeda:

 - Macros: fix 'HAS_*' redefinition by the '#[vtable]' macro
   under conditional compilation

* tag 'rust-fixes-6.5-rc7' of https://github.com/Rust-for-Linux/linux:
  rust: macros: vtable: fix `HAS_*` redefinition (`gen_const_name`)

Pull i2c fixes from Wolfram Sang:
 "Usual set of driver fixes. A bit more than usual because I was
  unavailable for a while"

* tag 'i2c-for-6.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: bcm-iproc: Fix bcm_iproc_i2c_isr deadlock issue
  i2c: Update documentation to use .probe() again
  i2c: sun6i-p2wi: Fix an error message in probe()
  i2c: hisi: Only handle the interrupt of the driver's transfer
  i2c: tegra: Fix i2c-tegra DMA config option processing
  i2c: tegra: Fix failure during probe deferral cleanup
  i2c: designware: Handle invalid SMBus block data response length value
  i2c: designware: Correct length byte validation logic
  i2c: imx-lpi2c: return -EINVAL when i2c peripheral clk doesn't work

Pull btrfs fixes from David Sterba:

 - fix infinite loop in readdir(), could happen in a big directory when
   files get renamed during enumeration

 - fix extent map handling of skipped pinned ranges

 - fix a corner case when handling ordered extent length

 - fix a potential crash when balance cancel races with pause

 - verify correct uuid when starting scrub or device replace

* tag 'for-6.5-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: fix incorrect splitting in btrfs_drop_extent_map_range
  btrfs: fix BUG_ON condition in btrfs_cancel_balance
  btrfs: only subtract from len_to_oe_boundary when it is tracking an extent
  btrfs: fix replace/scrub failure with metadata_uuid
  btrfs: fix infinite directory reads

Pull fbdev fixes and cleanups from Helge Deller:

 - various code cleanups in amifb, atmel_lcdfb, ssd1307fb, kyro and
   goldfishfb

* tag 'fbdev-for-6.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
  fbdev: goldfishfb: Do not check 0 for platform_get_irq()
  fbdev: atmel_lcdfb: Remove redundant of_match_ptr()
  fbdev: kyro: Remove unused declarations
  fbdev: ssd1307fb: Print the PWM's label instead of its number
  fbdev: mmp: fix value check in mmphw_probe()
  fbdev: amifb: Replace zero-length arrays with DECLARE_FLEX_ARRAY() helper

Pull block fixes from Jens Axboe:
 "Main thing here is the fix for the regression in flush handling which
  caused IO hangs/stalls for a few reporters. Hopefully that should all
  be sorted out now. Outside of that, just a few minor fixes for issues
  that were introduced in this cycle"

* tag 'block-6.5-2023-08-19' of git://git.kernel.dk/linux:
  blk-mq: release scheduler resource when request completes
  blk-crypto: dynamically allocate fallback profile
  blk-cgroup: hold queue_lock when removing blkg->q_node
  drivers/rnbd: restore sysfs interface to rnbd-client

Chuck reported [1] an IO hang problem on NFS exports that reside on SATA
devices and bisected to commit 615939a2 ("blk-mq: defer to the normal
submission path for post-flush requests").

We analysed the IO hang problem, found there are two postflush requests
waiting for each other.

The first postflush request completed the REQ_FSEQ_DATA sequence, so go to
the REQ_FSEQ_POSTFLUSH sequence and added in the flush pending list, but
failed to blk_kick_flush() because of the second postflush request which
is inflight waiting in scheduler queue.

The second postflush waiting in scheduler queue can't be dispatched because
the first postflush hasn't released scheduler resource even though it has
completed by itself.

Fix it by releasing scheduler resource when the first postflush request
completed, so the second postflush can be dispatched and completed, then
make blk_kick_flush() succeed.

While at it, remove the check for e->ops.finish_request, as all
schedulers set that. Reaffirm this requirement by adding a WARN_ON_ONCE()
at scheduler registration time, just like we do for insert_requests and
dispatch_request.

[1] https://lore.kernel.org/all/7A57C7AE-A51A-4254-888B-FE15CA21F9E9@oracle.com/

Link: https://lore.kernel.org/linux-block/20230819031206.2744005-1-chengming.zhou@linux.dev/Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202308172100.8ce4b853-oliver.sang@intel.com
Fixes: 615939a2 ("blk-mq: defer to the normal submission path for post-flush requests")
Reported-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Chengming Zhou <zhouchengming@bytedance.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
Link: https://lore.kernel.org/r/20230813152325.3017343-1-chengming.zhou@linux.dev
[axboe: folded in incremental fix and added tags]
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pull media fixes from Mauro Carvalho Chehab:
 "Three driver fixes"

* tag 'media/v6.5-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  media: imx: imx7-media-csi: Fix applying format constraints
  media: uvcvideo: Fix menu count handling for userspace XU mappings
  media: mtk-jpeg: Set platform driver data earlier

Pull x86 fixes from Borislav Petkov:
 "Extraordinary embargoed times call for extraordinary measures. That's
  why this week's x86/urgent branch is larger than usual, containing all
  the known fallout fixes after the SRSO mitigation got merged.

  I know, it is a bit late in the game but everyone who has reported a
  bug stemming from the SRSO pile, has tested that branch and has
  confirmed that it fixes their bug.

  Also, I've run it on every possible hardware I have and it is looking
  good. It is running on this very machine while I'm typing, for 2 days
  now without an issue. Famous last words...

   - Use LEA ...%rsp instead of ADD %rsp in the Zen1/2 SRSO return
     sequence as latter clobbers flags which interferes with fastop
     emulation in KVM, leading to guests freezing during boot

   - A fix for the DIV(0) quotient data leak on Zen1 to clear the
     divider buffers at the right time

   - Disable the SRSO mitigation on unaffected configurations as it got
     enabled there unnecessarily

   - Change .text section name to fix CONFIG_LTO_CLANG builds

   - Improve the optprobe indirect jmp check so that certain
     configurations can still be able to use optprobes at all

   - A serious and good scrubbing of the untraining routines by PeterZ:
      - Add proper speculation stopping traps so that objtool is happy
      - Adjust objtool to handle the new thunks
      - Make the thunk pointer assignable to the different untraining
        sequences at runtime, thus avoiding the alternative at the
        return thunk. It simplifies the code a bit too.
      - Add a entry_untrain_ret() main entry point which selects the
        respective untraining sequence
      - Rename things so that they're more clear
      - Fix stack validation with FRAME_POINTER=y builds

   - Fix static call patching to handle when a JMP to the return thunk
     is the last insn on the very last module memory page

   - Add more documentation about what each untraining routine does and
     why"

* tag 'x86_urgent_for_v6.5_rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/srso: Correct the mitigation status when SMT is disabled
  x86/static_call: Fix __static_call_fixup()
  objtool/x86: Fixup frame-pointer vs rethunk
  x86/srso: Explain the untraining sequences a bit more
  x86/cpu/kvm: Provide UNTRAIN_RET_VM
  x86/cpu: Cleanup the untrain mess
  x86/cpu: Rename srso_(.*)_alias to srso_alias_\1
  x86/cpu: Rename original retbleed methods
  x86/cpu: Clean up SRSO return thunk mess
  x86/alternative: Make custom return thunk unconditional
  objtool/x86: Fix SRSO mess
  x86/cpu: Fix up srso_safe_ret() and __x86_return_thunk()
  x86/cpu: Fix __x86_return_thunk symbol type
  x86/retpoline,kprobes: Skip optprobe check for indirect jumps with retpolines and IBT
  x86/retpoline,kprobes: Fix position of thunk sections with CONFIG_LTO_CLANG
  x86/srso: Disable the mitigation on unaffected configurations
  x86/CPU/AMD: Fix the DIV(0) initial fix attempt
  x86/retpoline: Don't clobber RFLAGS during srso_safe_ret()