This reverts commit e04653a9.

It is no longer needed to install Chrome EC GPE handler to have
GPE enabled in suspend to idle path. It is found that with this
handler installed, EC wake up doesn't work because default EC
event handler that can wake up system is not getting called.
Signed-off-by: Wenkai Du <wenkai.du@intel.com>
Acked-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Remove the GPL v2 license boilerplate and update with
the SPDX license identifier.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Commit 2dc49403 ("regulator: tps65218: Remove all the compatibles")
changes the probe function of drivers/regulator/tps65218-regulator.c so
that it iterates through all available regulators and assumes that the
regulator IDs are sequential and match the order present in the enum
tps65218_regulator_id. However, for some reason the much older commit
c0ea88b8 ("regulator: tps65218: add support for LS3 current
regulator") updated all arrays with LS3 at the end but added it second
to last for the enum.

Because of this long standing mismatch in order between the
tps65218_regulator_id enum and the regulator_desc array in the tps65218
regulator driver, the new probe function causes the strobe values to be
associated with the wrong regulator ID. This causes LDO1 to fail to
suspend in tps65218_pmic_set_suspend_disable due to not having anything
probes for its strobe value. Fix the order in the enum so the probe
function works as the update intended.

Fixes: 2dc49403 ("regulator: tps65218: Remove all the compatibles")
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This sets the regmap name to the device tree node name. This is useful
for debugging.
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Allocating memory to store clk array together with driver
data simplifies error unwinding and allows deleting memory
allocation failure message as there is now only single point
of failure already covered by allocation failure report.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
[Markus Elfring: simplified error unwinding, error message removal]
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Omit an extra message for a memory allocation failure in this function.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Omit an extra message for a memory allocation failure in these functions.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Omit an extra message for a memory allocation failure in this function.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Omit an extra message for a memory allocation failure in this function.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Omit an extra message for a memory allocation failure in this function.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Omit an extra message for a memory allocation failure in this function.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Omit an extra message for a memory allocation failure in this function.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Since commit 5812f010 ("phy: exynos4: Remove duplicated defines of
PHY register defines") and commit 7a66647b ("phy: exynos: Use one
define for enable bit") all users of syscon Exynos PMU headers (for PHY
drivers) are converted to use different headers so these can be removed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Merge tags 'ib-mfd-hwmon-v4.18', 'ib-mfd-input-rtc-v4.18' and 'ib-mfd-pwm-v4.18' into ibs-for-mfd-merged

Immutable branch between MFD and HWMON due for the v4.18 merge window

Immutable branch between MFD, Input and RTC due for the v4.18 merge window

Immutable branch between MFD and PWM due for the v4.18 merge window

Using input prescaler, capture unit will trigger DMA once every
configurable /2, /4 or /8 events (rising edge). This helps improve
period (only) capture accuracy at high rates.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Currently, capture is based on timeout window to configure prescaler.
PWM capture framework provides 1s window at the time of writing.

There's place for improvement, after input signal has been captured once:
- Finer tune counter clock prescaler, by using 1st capture result (with
arbitrary margin).
- Do a 2nd capture, with scaled capture window.
This increases accuracy, especially at high rates.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add support for PMW input mode on pwm-stm32. STM32 timers support
period and duty cycle capture as long as they have at least two PWM
channels. One capture channel is used for period (rising-edge), one
for duty-cycle (falling-edge).
When there's only one channel available, only period can be captured.
Duty-cycle is simply zero'ed in such a case.

Capture requires exclusive access (e.g. no pwm output running at the
same time, to protect common prescaler).
Timer DMA burst mode (from MFD core) is being used, to take two
snapshots of capture registers (upon each period rising edge).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

STM32 Timers can support up to 7 DMA requests:
- 4 channels, update, compare and trigger.
Optionally request part, or all DMAs from stm32-timers MFD core.

Also add routine to implement burst reads using DMA from timer registers.
This is exported. So, it can be used by child drivers, PWM capture
for instance (but not limited to).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch adds compatible strings and interrupts for pmic keys
which serves as child device of MFD.
Signed-off-by: Chen Zhong <chen.zhong@mediatek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch add support to handle MediaTek PMIC MT6397/MT6323 key
interrupts including pwrkey and homekey, also add setting for
long press key shutdown behavior.
Signed-off-by: Chen Zhong <chen.zhong@mediatek.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch adds documentation for device tree bindings for keys support
as the subnode of MT6397/MT6323 PMIC.
Signed-off-by: Chen Zhong <chen.zhong@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch adds the device tree binding documentation for the MediaTek
pmic keys found on PMIC MT6397/MT6323.
Signed-off-by: Chen Zhong <chen.zhong@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The core driver should create and manage irq mappings instead of
leaf drivers. This patch change to pass irq domain to
devm_mfd_add_devices() and it will create mapping for irq resources
automatically. And remove irq mapping in rtc driver since this has
been done in core driver.
Signed-off-by: Chen Zhong <chen.zhong@mediatek.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The uid and die temperature can be read out on the ADIN7 using
input mux. Map uid and die temperature sensor to channels 16
and 17.
Signed-off-by: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Pull more btrfs updates from David Sterba:
 "We have queued a few more fixes (error handling, log replay,
  softlockup) and the rest is SPDX updates that touche almost all files
  so the diffstat is long"

* tag 'for-4.17-part2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: Only check first key for committed tree blocks
  btrfs: add SPDX header to Kconfig
  btrfs: replace GPL boilerplate by SPDX -- sources
  btrfs: replace GPL boilerplate by SPDX -- headers
  Btrfs: fix loss of prealloc extents past i_size after fsync log replay
  Btrfs: clean up resources during umount after trans is aborted
  btrfs: Fix possible softlock on single core machines
  Btrfs: bail out on error during replay_dir_deletes
  Btrfs: fix NULL pointer dereference in log_dir_items

Pull cifs fixes from Steve French:
 "SMB3 fixes, a few for stable, and some important cleanup work from
  Ronnie of the smb3 transport code"

* tag '4.17-rc1SMB3-Fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: change validate_buf to validate_iov
  cifs: remove rfc1002 hardcoded constants from cifs_discard_remaining_data()
  cifs: Change SMB2_open to return an iov for the error parameter
  cifs: add resp_buf_size to the mid_q_entry structure
  smb3.11: replace a 4 with server->vals->header_preamble_size
  cifs: replace a 4 with server->vals->header_preamble_size
  cifs: add pdu_size to the TCP_Server_Info structure
  SMB311: Improve checking of negotiate security contexts
  SMB3: Fix length checking of SMB3.11 negotiate request
  CIFS: add ONCE flag for cifs_dbg type
  cifs: Use ULL suffix for 64-bit constant
  SMB3: Log at least once if tree connect fails during reconnect
  cifs: smb2pdu: Fix potential NULL pointer dereference

Pull SCSI fixes from James Bottomley:
 "This is a set of minor (and safe changes) that didn't make the initial
  pull request plus some bug fixes.

  The status handling code is actually a running regression from the
  previous merge window which had an incomplete fix (now reverted) and
  most of the remaining bug fixes are for problems older than the
  current merge window"

[ Side note: this merge also takes the base kernel git repository to 6+
  million objects for the first time. Technically we hit it a couple of
  merges ago already if you count all the tag objects, but now it
  reaches 6M+ objects reachable from HEAD.

  I was joking around that that's when I should switch to 5.0, because
  3.0 happened at the 2M mark, and 4.0 happened at 4M objects. But
  probably not, even if numerology is about as good a reason as any.

                                                              - Linus ]

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: devinfo: Add Microsoft iSCSI target to 1024 sector blacklist
  scsi: cxgb4i: silence overflow warning in t4_uld_rx_handler()
  scsi: dpt_i2o: Use after free in I2ORESETCMD ioctl
  scsi: core: Make scsi_result_to_blk_status() recognize CONDITION MET
  scsi: core: Rename __scsi_error_from_host_byte() into scsi_result_to_blk_status()
  Revert "scsi: core: return BLK_STS_OK for DID_OK in __scsi_error_from_host_byte()"
  scsi: aacraid: Insure command thread is not recursively stopped
  scsi: qla2xxx: Correct setting of SAM_STAT_CHECK_CONDITION
  scsi: qla2xxx: correctly shift host byte
  scsi: qla2xxx: Fix race condition between iocb timeout and initialisation
  scsi: qla2xxx: Avoid double completion of abort command
  scsi: qla2xxx: Fix small memory leak in qla2x00_probe_one on probe failure
  scsi: scsi_dh: Don't look for NULL devices handlers by name
  scsi: core: remove redundant assignment to shost->use_blk_mq

Pull more Kbuild updates from Masahiro Yamada:

 - pass HOSTLDFLAGS when compiling single .c host programs

 - build genksyms lexer and parser files instead of using shipped
   versions

 - rename *-asn1.[ch] to *.asn1.[ch] for suffix consistency

 - let the top .gitignore globally ignore artifacts generated by flex,
   bison, and asn1_compiler

 - let the top Makefile globally clean artifacts generated by flex,
   bison, and asn1_compiler

 - use safer .SECONDARY marker instead of .PRECIOUS to prevent
   intermediate files from being removed

 - support -fmacro-prefix-map option to make __FILE__ a relative path

 - fix # escaping to prepare for the future GNU Make release

 - clean up deb-pkg by using debian tools instead of handrolled
   source/changes generation

 - improve rpm-pkg portability by supporting kernel-install as a
   fallback of new-kernel-pkg

 - extend Kconfig listnewconfig target to provide more information

* tag 'kbuild-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kconfig: extend output of 'listnewconfig'
  kbuild: rpm-pkg: use kernel-install as a fallback for new-kernel-pkg
  Kbuild: fix # escaping in .cmd files for future Make
  kbuild: deb-pkg: split generating packaging and build
  kbuild: use -fmacro-prefix-map to make __FILE__ a relative path
  kbuild: mark $(targets) as .SECONDARY and remove .PRECIOUS markers
  kbuild: rename *-asn1.[ch] to *.asn1.[ch]
  kbuild: clean up *-asn1.[ch] patterns from top-level Makefile
  .gitignore: move *-asn1.[ch] patterns to the top-level .gitignore
  kbuild: add %.dtb.S and %.dtb to 'targets' automatically
  kbuild: add %.lex.c and %.tab.[ch] to 'targets' automatically
  genksyms: generate lexer and parser during build instead of shipping
  kbuild: clean up *.lex.c and *.tab.[ch] patterns from top-level Makefile
  .gitignore: move *.lex.c *.tab.[ch] patterns to the top-level .gitignore
  kbuild: use HOSTLDFLAGS for single .c executables

Pull x86 fixes from Thomas Gleixner:
 "A set of fixes and updates for x86:

   - Address a swiotlb regression which was caused by the recent DMA
     rework and made driver fail because dma_direct_supported() returned
     false

   - Fix a signedness bug in the APIC ID validation which caused invalid
     APIC IDs to be detected as valid thereby bloating the CPU possible
     space.

   - Fix inconsisten config dependcy/select magic for the MFD_CS5535
     driver.

   - Fix a corruption of the physical address space bits when encryption
     has reduced the address space and late cpuinfo updates overwrite
     the reduced bit information with the original value.

   - Dominiks syscall rework which consolidates the architecture
     specific syscall functions so all syscalls can be wrapped with the
     same macros. This allows to switch x86/64 to struct pt_regs based
     syscalls. Extend the clearing of user space controlled registers in
     the entry patch to the lower registers"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/apic: Fix signedness bug in APIC ID validity checks
  x86/cpu: Prevent cpuinfo_x86::x86_phys_bits adjustment corruption
  x86/olpc: Fix inconsistent MFD_CS5535 configuration
  swiotlb: Use dma_direct_supported() for swiotlb_ops
  syscalls/x86: Adapt syscall_wrapper.h to the new syscall stub naming convention
  syscalls/core, syscalls/x86: Rename struct pt_regs-based sys_*() to __x64_sys_*()
  syscalls/core, syscalls/x86: Clean up compat syscall stub naming convention
  syscalls/core, syscalls/x86: Clean up syscall stub naming convention
  syscalls/x86: Extend register clearing on syscall entry to lower registers
  syscalls/x86: Unconditionally enable 'struct pt_regs' based syscalls on x86_64
  syscalls/x86: Use 'struct pt_regs' based syscall calling for IA32_EMULATION and x32
  syscalls/core: Prepare CONFIG_ARCH_HAS_SYSCALL_WRAPPER=y for compat syscalls
  syscalls/x86: Use 'struct pt_regs' based syscall calling convention for 64-bit syscalls
  syscalls/core: Introduce CONFIG_ARCH_HAS_SYSCALL_WRAPPER=y
  x86/syscalls: Don't pointlessly reload the system call number
  x86/mm: Fix documentation of module mapping range with 4-level paging
  x86/cpuid: Switch to 'static const' specifier

Pull x86 pti updates from Thomas Gleixner:
 "Another series of PTI related changes:

   - Remove the manual stack switch for user entries from the idtentry
     code. This debloats entry by 5k+ bytes of text.

   - Use the proper types for the asm/bootparam.h defines to prevent
     user space compile errors.

   - Use PAGE_GLOBAL for !PCID systems to gain back performance

   - Prevent setting of huge PUD/PMD entries when the entries are not
     leaf entries otherwise the entries to which the PUD/PMD points to
     and are populated get lost"

* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/pgtable: Don't set huge PUD/PMD on non-leaf entries
  x86/pti: Leave kernel text global for !PCID
  x86/pti: Never implicitly clear _PAGE_GLOBAL for kernel image
  x86/pti: Enable global pages for shared areas
  x86/mm: Do not forbid _PAGE_RW before init for __ro_after_init
  x86/mm: Comment _PAGE_GLOBAL mystery
  x86/mm: Remove extra filtering in pageattr code
  x86/mm: Do not auto-massage page protections
  x86/espfix: Document use of _PAGE_GLOBAL
  x86/mm: Introduce "default" kernel PTE mask
  x86/mm: Undo double _PAGE_PSE clearing
  x86/mm: Factor out pageattr _PAGE_GLOBAL setting
  x86/entry/64: Drop idtentry's manual stack switch for user entries
  x86/uapi: Fix asm/bootparam.h userspace compilation errors

Pull scheduler fixes from Thomas Gleixner:
 "A few scheduler fixes:

   - Prevent a bogus warning vs. runqueue clock update flags in
     do_sched_rt_period_timer()

   - Simplify the helper functions which handle requests for skipping
     the runqueue clock updat.

   - Do not unlock the tunables mutex in the error path of the cpu
     frequency scheduler utils. Its not held.

   - Enforce proper alignement for 'struct util_est' in sched_avg to
     prevent a misalignment fault on IA64"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/core: Force proper alignment of 'struct util_est'
  sched/core: Simplify helpers for rq clock update skip requests
  sched/rt: Fix rq->clock_update_flags < RQCF_ACT_SKIP warning
  sched/cpufreq/schedutil: Fix error path mutex unlock

Pull more perf updates from Thomas Gleixner:
 "A rather large set of perf updates:

  Kernel:

   - Fix various initialization issues

   - Prevent creating [ku]probes for not CAP_SYS_ADMIN users

  Tooling:

   - Show only failing syscalls with 'perf trace --failure' (Arnaldo
     Carvalho de Melo)

            e.g: See what 'openat' syscalls are failing:

        # perf trace --failure -e openat
         762.323 ( 0.007 ms): VideoCapture/4566 openat(dfd: CWD, filename: /dev/video2) = -1 ENOENT No such file or directory
         <SNIP N /dev/videoN open attempts... sigh, where is that improvised camera lid?!? >
         790.228 ( 0.008 ms): VideoCapture/4566 openat(dfd: CWD, filename: /dev/video63) = -1 ENOENT No such file or directory
        ^C#

   - Show information about the event (freq, nr_samples, total
     period/nr_events) in the annotate --tui and --stdio2 'perf
     annotate' output, similar to the first line in the 'perf report
     --tui', but just for the samples for a the annotated symbol
     (Arnaldo Carvalho de Melo)

   - Introduce 'perf version --build-options' to show what features were
     linked, aliased as well as a shorter 'perf -vv' (Jin Yao)

   - Add a "dso_size" sort order (Kim Phillips)

   - Remove redundant ')' in the tracepoint output in 'perf trace'
     (Changbin Du)

   - Synchronize x86's cpufeatures.h, no effect on toolss (Arnaldo
     Carvalho de Melo)

   - Show group details on the title line in the annotate browser and
     'perf annotate --stdio2' output, so that the per-event columns can
     have headers (Arnaldo Carvalho de Melo)

   - Fixup vertical line separating metrics from instructions and
     cleaning unused lines at the bottom, both in the annotate TUI
     browser (Arnaldo Carvalho de Melo)

   - Remove duplicated 'samples' in lost samples warning in
     'perf report' (Arnaldo Carvalho de Melo)

   - Synchronize i915_drm.h, silencing the perf build process,
     automagically adding support for the new DRM_I915_QUERY ioctl
     (Arnaldo Carvalho de Melo)

   - Make auxtrace_queues__add_buffer() allocate struct buffer, from a
     patchkit already applied (Adrian Hunter)

   - Fix the --stdio2/TUI annotate output to include group details, be
     it for a recorded '{a,b,f}' explicit event group or when forcing
     group display using 'perf report --group' for a set of events not
     recorded as a group (Arnaldo Carvalho de Melo)

   - Fix display artifacts in the ui browser (base class for the
     annotate and main report/top TUI browser) related to the extra
     title lines work (Arnaldo Carvalho de Melo)

   - perf auxtrace refactorings, leftovers from a previously partially
     processed patchset (Adrian Hunter)

   - Fix the builtin clang build (Sandipan Das, Arnaldo Carvalho de
     Melo)

   - Synchronize i915_drm.h, silencing a perf build warning and in the
     process automagically adding support for a new ioctl command
     (Arnaldo Carvalho de Melo)

   - Fix a strncpy issue in uprobe tracing"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
  perf/core: Need CAP_SYS_ADMIN to create k/uprobe with perf_event_open()
  tracing/uprobe_event: Fix strncpy corner case
  perf/core: Fix perf_uprobe_init()
  perf/core: Fix perf_kprobe_init()
  perf/core: Fix use-after-free in uprobe_perf_close()
  perf tests clang: Fix function name for clang IR test
  perf clang: Add support for recent clang versions
  perf tools: Fix perf builds with clang support
  perf tools: No need to include namespaces.h in util.h
  perf hists browser: Remove leftover from row returned from refresh
  perf hists browser: Show extra_title_lines in the 'D' debug hotkey
  perf auxtrace: Make auxtrace_queues__add_buffer() do CPU filtering
  tools headers uapi: Synchronize i915_drm.h
  perf report: Remove duplicated 'samples' in lost samples warning
  perf ui browser: Fixup cleaning unused lines at the bottom
  perf annotate browser: Fixup vertical line separating metrics from instructions
  perf annotate: Show group details on the title line
  perf auxtrace: Make auxtrace_queues__add_buffer() allocate struct buffer
  perf/x86/intel: Move regs->flags EXACT bit init
  perf trace: Remove redundant ')'
  ...

Pull x86 EFI bootup fixlet from Thomas Gleixner:
 "A single fix for an early boot warning caused by invoking
  this_cpu_has() before SMP initialization"

* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm: Fix bogus warning during EFI bootup, use boot_cpu_has() instead of this_cpu_has() in build_cr3_noflush()

Pull irq affinity fixes from Thomas Gleixner:

  - Fix error path handling in the affinity spreading code

  - Make affinity spreading smarter to avoid issues on systems which
    claim to have hotpluggable CPUs while in fact they can't hotplug
    anything.

    So instead of trying to spread the vectors (and thereby the
    associated device queues) to all possibe CPUs, spread them on all
    present CPUs first. If there are left over vectors after that first
    step they are spread among the possible, but not present CPUs which
    keeps the code backwards compatible for virtual decives and NVME
    which allocate a queue per possible CPU, but makes the spreading
    smarter for devices which have less queues than possible or present
    CPUs.

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/affinity: Spread irq vectors among present CPUs as far as possible
  genirq/affinity: Allow irq spreading from a given starting point
  genirq/affinity: Move actual irq vector spreading into a helper function
  genirq/affinity: Rename *node_to_possible_cpumask as *node_to_cpumask
  genirq/affinity: Don't return with empty affinity masks on error

Pull OpenRISC fixlet from Stafford Horne:
 "Just one small thing here, it came in a while back but I didnt have
  anything in my 4.16 queue, still its the only thing for 4.17 so
  sending it alone.

  Small cleanup: remove unused __ARCH_HAVE_MMU define"

* tag 'for-linus' of git://github.com/openrisc/linux:
  openrisc: remove unused __ARCH_HAVE_MMU define

Pull powerpc fixes from Michael Ellerman:

 - Fix crashes when loading modules built with a different
   CONFIG_RELOCATABLE value by adding CONFIG_RELOCATABLE to vermagic.

 - Fix busy loops in the OPAL NVRAM driver if we get certain error
   conditions from firmware.

 - Remove tlbie trace points from KVM code that's called in real mode,
   because it causes crashes.

 - Fix checkstops caused by invalid tlbiel on Power9 Radix.

 - Ensure the set of CPU features we "know" are always enabled is
   actually the minimal set when we build with support for firmware
   supplied CPU features.

Thanks to: Aneesh Kumar K.V, Anshuman Khandual, Nicholas Piggin.

* tag 'powerpc-4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s: Fix CPU_FTRS_ALWAYS vs DT CPU features
  powerpc/mm/radix: Fix checkstops caused by invalid tlbiel
  KVM: PPC: Book3S HV: trace_tlbie must not be called in realmode
  powerpc/8xx: Fix build with hugetlbfs enabled
  powerpc/powernv: Fix OPAL NVRAM driver OPAL_BUSY loops
  powerpc/powernv: define a standard delay for OPAL_BUSY type retry loops
  powerpc/fscr: Enable interrupts earlier before calling get_user()
  powerpc/64s: Fix section mismatch warnings from setup_rfi_flush()
  powerpc/modules: Fix crashes by adding CONFIG_RELOCATABLE to vermagic

Merge yet more updates from Andrew Morton:

 - various hotfixes

 - kexec_file updates and feature work

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (27 commits)
  kernel/kexec_file.c: move purgatories sha256 to common code
  kernel/kexec_file.c: allow archs to set purgatory load address
  kernel/kexec_file.c: remove mis-use of sh_offset field during purgatory load
  kernel/kexec_file.c: remove unneeded variables in kexec_purgatory_setup_sechdrs
  kernel/kexec_file.c: remove unneeded for-loop in kexec_purgatory_setup_sechdrs
  kernel/kexec_file.c: split up __kexec_load_puragory
  kernel/kexec_file.c: use read-only sections in arch_kexec_apply_relocations*
  kernel/kexec_file.c: search symbols in read-only kexec_purgatory
  kernel/kexec_file.c: make purgatory_info->ehdr const
  kernel/kexec_file.c: remove checks in kexec_purgatory_load
  include/linux/kexec.h: silence compile warnings
  kexec_file, x86: move re-factored code to generic side
  x86: kexec_file: clean up prepare_elf64_headers()
  x86: kexec_file: lift CRASH_MAX_RANGES limit on crash_mem buffer
  x86: kexec_file: remove X86_64 dependency from prepare_elf64_headers()
  x86: kexec_file: purge system-ram walking from prepare_elf64_headers()
  kexec_file,x86,powerpc: factor out kexec_file_ops functions
  kexec_file: make use of purgatory optional
  proc: revalidate misc dentries
  mm, slab: reschedule cache_reap() on the same CPU
  ...

The code to verify the new kernels sha digest is applicable for all
architectures.  Move it to common code.

One problem is the string.c implementation on x86.  Currently sha256
includes x86/boot/string.h which defines memcpy and memset to be gcc
builtins.  By moving the sha256 implementation to common code and
changing the include to linux/string.h both functions are no longer
defined.  Thus definitions have to be provided in x86/purgatory/string.c

Link: http://lkml.kernel.org/r/20180321112751.22196-12-prudo@linux.vnet.ibm.comSigned-off-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>