Resume path calls .open but suspend path cannot call .stop because
fdirs should not be freed and control over hardware should not be
released until WoL is configured.  To avoid having to duplicate all
changes made in .stop on suspend path split out part of .stop that
is relevant during suspend and call it from .stop and during suspend.

This fix also ensures that ixgbe_ptp_suspend is called during the
suspend path, and helps avoid similar errors. We can't call
ixgbe_ptp_stop, since it will free the PTP clock device, which we
shouldn't be doing during a suspend path.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Since we are adding proper support for suspend of PTP, extract out of
ixgbe_ptp_stop those things relevant to suspend. Then, have
ixgbe_ptp_stop call ixgbe_ptp_suspend. The next patch in the series will
have ixgbe_ptp_suspend called from the ixgbe_suspend path.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In order to properly handle a suspend/resume cycle, we cannot destroy
the PTP clock device. As part of this, we should only re-create the
device on first initialization. After a resume, when ixgbe_ptp_init is
called, we won't create a new clock, and we will use the old clock
device. To that end, this patch extracts the clock creation out of
ptp_init, and only calls it if we don't already have a ptp_clock
pointer.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Rather than clearing the hwtstamp configuration, we should use the known
configuration requested by the user and call the function which has now
been separated from the ioctl. This means that after a reset, the
timestamp mode will be maintained rather than lost. We still can't
maintain the clock value, however.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently all of the hardware setup logic for the PTP hardware bits is
buried inside of the ioctl which sets the timestamp configuration. This
makes it hard to use this logic in other places (primarily reset), and
this means we can't restore current timestamp mode upon a MAC reset.
Extracting this logic into a separate function will enable future work
for the ixgbe_ptp_reset function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Since the name ixgbe_ptp_enable could be misconstrued as a function
which enables the whole PTP core, rename this function so that it is
clear the function is for enabling of the extra features such as PPS
signal.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Driver was calling setup_link to make sure that fiber interfaces with MNG FW
enabled will get link on probe because the laser was most likely turned off.
This prevented non-fiber devices with MNG FW from linking at 100Mbps.

This patch adds a check to only call setup_link for fiber devices.
Reported-and-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Florian Fainelli says:

====================
net: sysfs: documentation updates

This patch set contains some updates to the sysfs Documentation for the
sysfs net class.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Document the network device statistics counter that are exposed as sysfs
attributes.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add sysfs documentation for the various attributes of a network
interface exposed in /sys/class/<iface>/queues/{rx,tx}-<queue>/
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add documentation for the phys_port_id sysfs attribute of a network
device.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before f5efc696 ("netfilter: nf_tables: Add meta expression key for
bridge interface name"), the entire net/bridge/netfilter/ directory
depended on BRIDGE_NF_EBTABLES, ie. on ebtables. However, that
directory already contained the nf_tables bridge extension that
we should allow to compile separately. In f5efc696, we tried to
generalize this by using CONFIG_BRIDGE_NETFILTER which was not a good
idea since this option already existed and it is dedicated to enable
the Netfilter bridge IP/ARP filtering.

Let's try to fix this mess by:

1) making net/bridge/netfilter/ dependent on the toplevel
   CONFIG_NETFILTER option, just like we do with the net/netfilter and
   net/ipv{4,6}/netfilter/ directories.

2) Changing 'selects' to 'depends on' NETFILTER_XTABLES for
   BRIDGE_NF_EBTABLES. I believe this problem was already before
   f5efc696:

warning: (BRIDGE_NF_EBTABLES) selects NETFILTER_XTABLES which has
unmet direct dependencies (NET && INET && NETFILTER)

3) Fix ebtables/nf_tables bridge dependencies by making NF_TABLES_BRIDGE
   and BRIDGE_NF_EBTABLES dependent on BRIDGE and NETFILTER:

warning: (NF_TABLES_BRIDGE && BRIDGE_NF_EBTABLES) selects
BRIDGE_NETFILTER which has unmet direct dependencies (NET && BRIDGE &&
NETFILTER && INET && NETFILTER_ADVANCED)

net/built-in.o: In function `br_parse_ip_options':
br_netfilter.c:(.text+0x4a5ba): undefined reference to `ip_options_compile'
br_netfilter.c:(.text+0x4a5ed): undefined reference to `ip_options_rcv_srr'
net/built-in.o: In function `br_nf_pre_routing_finish':
br_netfilter.c:(.text+0x4a8a4): undefined reference to `ip_route_input_noref'
br_netfilter.c:(.text+0x4a987): undefined reference to `ip_route_output_flow'
make: *** [vmlinux] Error 1
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit de906af1 (net: phy: make of_set_phy_supported work with genphy driver)
removed the last user of variable 'max_speed' in function
of_mdiobus_register_phy(), leading to compile warning "unused variable
‘max_speed’ [-Wunused-variable]". Thus remove it.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When cable is not present the clock speed of some of the devices is
reduced based upon power saving mode setting in NVRAM. Due to this
NVRAM reads take long time to complete as a result CPU soft lockup
message is seen. Fix is to override clock, disable link aware and link
idle modes before NVRAM reads and restore them back after the reads
are complete. During this period also check if the thread needs to be
rescheduled and if there are any signals to handle.

Also decrease the NVRAM command execution timeout value to 1ms.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

kernel always invokes a pair of rtnl_lock adn rtnl_unlock to
protect dev_ethtool(), so its not neccessary to invoke spin_lock/unlock
in ethtool_ops.
Signed-off-by: Yang Wei <Wei.Yang@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sock_fprog and sock_fprog_kern are of equal size, however
it's cleaner to just use sizeof(*fprog) instead to always
have correct type.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As it may then take longer than what the user specified using
setsockopt(SO_RCVTIMEO).
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stephen Boyd says:

====================
ks8851 DT/regulator/gpio updates

This set of patches properly documents the micrel ks8851 spi ethernet
controller, converts to devm_regulator_get_optional() to make error
paths slightly simpler, and finally adds supports for another
optional regulator and a reset gpio. This allows me to use the ks8851
on my MSM8960 CDP board.

Changes since v1:
 * Dropped vendor prefix patch as that should go through DT tree
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Users are currently just providing "ks8851" as the compatible for
this driver in device tree. Add a compatible string that provides
the vendor name along with the device name to be more explicit.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow the ks8851 driver to enable an optional 1.8V vdd_io
regulator and assert the reset pin to the phy if a reset gpio is
present in device tree.

Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This simplifies error paths and removes the need to
regulator_put().

Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ks8851 SPI ethernet wasn't documented, but we documented the
optional regulator supply for it under the mll based ethernet
chip. Furthermore, that compatible string needed another 'l'. Fix
all of this and document the optional vdd-io and reset-gpios
properties.

Cc: Nishanth Menon <nm@ti.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/bonding/bond_alb.c
	drivers/net/ethernet/altera/altera_msgdma.c
	drivers/net/ethernet/altera/altera_sgdma.c
	net/ipv6/xfrm6_output.c

Several cases of overlapping changes.

The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.

In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.

Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull sparc fixes from David Miller:
 "A small bunch of bug fixes, in particular:

   1) On older cpus we need a different chunk of virtual address space
      to map the huge page TSB.

   2) Missing memory barrier in Niagara2 memcpy.

   3) trinity showed some places where fault validation was
      unnecessarily loud on sparc64

   4) Some sysfs printf's need a type adjustment, from Toralf Förster"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: fix format string mismatch in arch/sparc/kernel/sysfs.c
  sparc64: Add membar to Niagara2 memcpy code.
  sparc64: Fix huge TSB mapping on pre-UltraSPARC-III cpus.
  sparc64: Don't bark so loudly about 32-bit tasks generating 64-bit fault addresses.

Pull networking fixes from David Miller:
 "It looks like a sizeble collection but this is nearly 3 weeks of bug
  fixing while you were away.

   1) Fix crashes over IPSEC tunnels with NAT, the latter can reroute
      the packet through a non-IPSEC protected path and the code has to
      be able to handle SKBs attached to routes lacking an attached xfrm
      state.  From Steffen Klassert.

   2) Fix OOPSs in ipv4 and ipv6 ipsec layers for unsupported
      sub-protocols, also from Steffen Klassert.

   3) Set local_df on fragmented netfilter skbs otherwise we won't be
      able to forward successfully, from Florian Westphal.

   4) cdc_mbim ipv6 neighbour code does __vlan_find_dev_deep without
      holding RCU lock, from Bjorn Mork.

   5) local_df test in ip_may_fragment is inverted, from Florian
      Westphal.

   6) jme driver doesn't check for DMA mapping failures, from Neil
      Horman.

   7) qlogic driver doesn't calculate number of TX queues properly, from
      Shahed Shaikh.

   8) fib_info_cnt can drift irreversibly positive if we fail to
      allocate the fi->fib_metrics array, from Sergey Popovich.

   9) Fix use after free in ip6_route_me_harder(), also from Sergey
      Popovich.

  10) When SYSCTL is disabled, we don't handle local_port_range and
      ping_group_range defaults properly at all, from Cong Wang.

  11) Unaccelerated VLAN tagged frames improperly handled by cdc_mbim
      driver, fix from Bjorn Mork.

  12) cassini driver needs nested lock annotations for TX locking, from
      Emil Goode.

  13) On init error ipv6 VTI driver can unregister pernet ops twice,
      oops.  Fix from Mahtias Krause.

  14) If macvlan device is down, don't propagate IFF_ALLMULTI changes,
      from Peter Christensen.

  15) Missing NULL pointer check while parsing netlink config options in
      ip6_tnl_validate().  From Susant Sahani.

  16) Fix handling of neighbour entries during ipv6 router reachability
      probing, from Duan Jiong.

  17) x86 and s390 JIT address randomization has some address
      calculation bugs leading to crashes, from Alexei Starovoitov and
      Heiko Carstens.

  18) Clear up those uglies with nop patching and net_get_random_once(),
      from Hannes Frederic Sowa.

  19) Option length miscalculated in ip6_append_data(), fix also from
      Hannes Frederic Sowa.

  20) A while ago we fixed a race during device unregistry when a
      namespace went down, turns out there is a second place that needs
      similar protection.  From Cong Wang.

  21) In the new Altera TSE driver multicast filtering isn't working,
      disable it and just use promisc mode until the cause is found.
      From Vince Bridgers.

  22) When we disable router enabling in ipv6 we have to flush the
      cached routes explicitly, from Duan Jiong.

  23) NBMA tunnels should not cache routes on the tunnel object because
      the key is variable, from Timo Teräs.

  24) With stacked devices GRO information in skb->cb[] can be not setup
      properly, make sure it is in all code paths.  From Eric Dumazet.

  25) Really fix stacked vlan locking, multiple levels of nesting with
      intervening non-vlan devices are possible.  From Vlad Yasevich.

  26) Fallback ipip tunnel device's mtu is not setup properly, from
      Steffen Klassert.

  27) The packet scheduler's tcindex filter can crash because we
      structure copy objects with list_head's inside, oops.  From Cong
      Wang.

  28) Fix CHECKSUM_COMPLETE handling for ipv6 GRE tunnels, from Eric
      Dumazet.

  29) In some configurations 'itag' in __mkroute_input() can end up
      being used uninitialized because of how fib_validate_source()
      works.  Fix it by explitly initializing itag to zero like all the
      other fib_validate_source() callers do, from Li RongQing"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
  batman: fix a bogus warning from batadv_is_on_batman_iface()
  ipv4: initialise the itag variable in __mkroute_input
  bonding: Send ALB learning packets using the right source
  bonding: Don't assume 802.1Q when sending alb learning packets.
  net: doc: Update references to skb->rxhash
  stmmac: Remove unbalanced clk_disable call
  ipv6: gro: fix CHECKSUM_COMPLETE support
  net_sched: fix an oops in tcindex filter
  can: peak_pci: prevent use after free at netdev removal
  ip_tunnel: Initialize the fallback device properly
  vlan: Fix build error wth vlan_get_encap_level()
  can: c_can: remove obsolete STRICT_FRAME_ORDERING Kconfig option
  MAINTAINERS: Pravin Shelar is Open vSwitch maintainer.
  bnx2x: Convert return 0 to return rc
  bonding: Fix alb mode to only use first level vlans.
  bonding: Fix stacked device detection in arp monitoring
  macvlan: Fix lockdep warnings with stacked macvlan devices
  vlan: Fix lockdep warning with stacked vlan devices.
  net: Allow for more then a single subclass for netif_addr_lock
  net: Find the nesting level of a given device by type.
  ...

Daniel Borkmann says:

====================
BPF updates

These were still in my queue. Please see individual patches for
details.

I have rebased these on top of current net-next with Andrew's
gcc union fixup [1] applied to avoid dealing with an unnecessary
merge conflict.

 [1] http://patchwork.ozlabs.org/patch/351577/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds three more test cases:

 1) long jumps with holes of unreachable code
 2) ret x
 3) ldx + ret x

All three tests are for classical BPF and to make sure that
any changes will not break some exotic behaviour that exists
probably since decades. The last two tests are expected to
fail by the BPF checker already, as in classic BPF only K
or A are allowed to be returned. Thus, there are now 52 test
cases for BPF.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch simplifies and refactors the test case code a
bit and also adds a summary of all test that passed or
failed in the kernel log, so that it's easier to spot if
something has failed.

Future work could further extend the test framework to also
support different input 'stimuli' i.e. related structures
to seccomp.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mention the recently added test suite in the documentation file.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The sk_unattached_filter_create() API is used by BPF filters that
are not directly attached or related to sockets, and are used in
team, ptp, xt_bpf, cls_bpf, etc. As such all users do their own
internal managment of obtaining filter blocks and thus already
have them in kernel memory and set up before calling into
sk_unattached_filter_create(). As a result, due to __user annotation
in sock_fprog, sparse triggers false positives (incorrect type in
assignment [different address space]) when filters are set up before
passing them to sk_unattached_filter_create(). Therefore, let
sk_unattached_filter_create() API use sock_fprog_kern to overcome
this issue.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Lets get rid of this macro. After commit 5bcfedf0 ("net: filter:
simplify label names from jump-table"), labels have become more
readable due to omission of BPF_ prefix but at the same time more
generic, so that things like `git grep -n` would not find them. As
a middle path, lets get rid of the DL macro as it's not strictly
needed and would otherwise just hide the full name.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tom Herbert says:

====================
net: Checksum offload changes - Part III

I am working on overhauling RX checksum offload. Goals of this effort
are:

- Specify what exactly it means when driver returns CHECKSUM_UNNECESSARY
- Preserve CHECKSUM_COMPLETE through encapsulation layers
- Don't do skb_checksum more than once per packet
- Unify GRO and non-GRO csum verification as much as possible
- Unify the checksum functions (checksum_init)
- Simply code

What is in this third patch set:

- Remove sk_no_check from sunrpc (doesn't seem to have any effect)
- Eliminate no_check from protosw. All protocols are using default of
  zero for this
- Split sk_no_check into sk_no_check_tx and sk_no_check_rx
- Make enabling of UDP6 more restrictive and explicit
- Support zero UDP6 checksums in l2tp

V2: Took out vxlan changes to set zero csums in IPv6, this will
    be in a later patch set.
V3: Fixed bug in restricting UDP6 checksums.

Please review carefully and test if possible, mucking with basic
checksum functions is always a little precarious :-)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Added new L2TP configuration options to allow TX and RX of
zero checksums in IPv6. Default is not to use them.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RFC 6935 permits zero checksums to be used in IPv6 however this is
recommended only for certain tunnel protocols, it does not make
checksums completely optional like they are in IPv4.

This patch restricts the use of IPv6 zero checksums that was previously
intoduced. no_check6_tx and no_check6_rx have been added to control
the use of checksums in UDP6 RX and TX path. The normal
sk_no_check_{rx,tx} settings are not used (this avoids ambiguity when
dealing with a dual stack socket).

A helper function has been added (udp_set_no_check6) which can be
called by tunnel impelmentations to all zero checksums (send on the
socket, and accept them as valid).
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Define separate fields in the sock structure for configuring disabling
checksums in both TX and RX-- sk_no_check_tx and sk_no_check_rx.
The SO_NO_CHECK socket option only affects sk_no_check_tx. Also,
removed UDP_CSUM_* defines since they are no longer necessary.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It doesn't seem like an protocols are setting anything other
than the default, and allowing to arbitrarily disable checksums
for a whole protocol seems dangerous. This can be done on a per
socket basis.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Setting sk_no_check to UDP_CSUM_NORCV seems to have no effect.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series contains updates to igb, igbvf, ixgbe, i40e and i40evf.

Jacob provides eight patches to cleanup the ixgbe driver to resolve various
checkpatch.pl warnings/errors as well as minor coding style issues.

Stephen Hemminger and I provide simple cleanups of void functions which
had useless return statements at the end of the function which are not
needed.

v2: Dropped Emil's patch "ixgbe: fix the detection of SFP+ capable interfaces"
    while I wait for his updated patch to be validated.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Ezequiel Garcia says:

====================
net: ethernet: marvell: Assorted fixes

New round for this assorted fixes and clean-up series. There is more room for
clean-ups, and I'll start preparing more patches once these are accepted.

This series consists of cleanups and minor improvements on mvneta, mv643xx_eth
and mvmdio drivers. None of the patches imply any functionality change, except
for the patch six "Change the number of default rx queues to one".

This patch reduces the driver's allocated resources and makes the multiqueue
path in the poll function not get taken. The previous patchset contains more
details:

  http://permalink.gmane.org/gmane.linux.network/315015

As usual, any feedback on this will be well received!

Changes from v2:

  * Rebased on today's net-next and dropped patch
    "net: mvneta: Factorize feature setting", merged in the recent
    TSO series.

  * As per Sergei suggestion, used devm_kcalloc or devm_kmalloc_array
    when suitable.

Changes from v1:

  * Added two more clean-up patches to the series.

  * Added Sebastian's Acked-by's.

  * Fixed extra empty line in "net: mv643xx_eth: Simplify
    mv643xx_eth_adjust_link()" as pointed out by David Miller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The 'weight' field is only used to pass the weigth to napi initialization
function. This commit removes the field, and instead uses a fixed value to
initialize the napi context.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>