0x20FF(amp global enable) register was defined as non-volatile,
but it is not. Overheating, overcurrent can cause amp shutdown
in hardware.
'regmap_write' compare register readback value before writing
to avoid same value writing. 'regmap_read' just read cache
not actual hardware value for the non-volatile register.
When amp is internally shutdown by some reason, next 'AMP ON'
command can be ignored because regmap think amp is already ON.
Signed-off-by: Ryan Lee <ryans.lee@maximintegrated.com>
Link: https://lore.kernel.org/r/20210325033555.29377-1-ryans.lee@maximintegrated.comSigned-off-by: Mark Brown <broonie@kernel.org>

The media and deep-buffer DAIs only support 48000 Hz samplerate,
remove the 44100 sample-rate from their descriptions.
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210324132711.216152-3-hdegoede@redhat.comSigned-off-by: Mark Brown <broonie@kernel.org>

The SST firmware's media and deep-buffer inputs are hardcoded to
S16LE, the corresponding DAIs don't have a hw_params callback and
their prepare callback also does not take the format into account.

So far the advertising of non working S24LE support has not caused
issues because pulseaudio defaults to S16LE, but changing pulse-audio's
config to use S24LE will result in broken sound.

Pipewire is replacing pulse now and pipewire prefers S24LE over S16LE
when available, causing the problem of the broken S24LE support to
come to the surface now.

Cc: stable@vger.kernel.org
BugLink: https://gitlab.freedesktop.org/pipewire/pipewire/-/issues/866
Fixes: 098c2cd2 ("ASoC: Intel: Atom: add 24-bit support for media playback and capture")
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210324132711.216152-2-hdegoede@redhat.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series "ASoC: SOF: Intel: shutdown and core handling corrections" from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:

This patchset fixes a logical flow in the core status, improves
shutdown support on Intel SOF platforms with an HDaudio controller and
cleans-up ElkhartLake support.

Guennadi Liakhovetski (1):
  ASoC: SOF: Intel: HDA: fix core status verification

Libin Yang (5):
  ASoC: SOF: Intel: TGL: fix EHL ops
  ASoC: SOF: Intel: TGL: set shutdown callback to hda_dsp_shutdown
  ASoC: SOF: Intel: ICL: set shutdown callback to hda_dsp_shutdown
  ASoC: SOF: Intel: CNL: set shutdown callback to hda_dsp_shutdown
  ASoC: SOF: Intel: APL: set shutdown callback to hda_dsp_shutdown

Pierre-Louis Bossart (2):
  ASoC: SOF: core: harden shutdown helper
  ASoC: SOF: Intel: move ELH chip info

 sound/soc/sof/core.c          |  8 +++++++-
 sound/soc/sof/intel/apl.c     |  3 ++-
 sound/soc/sof/intel/cnl.c     | 19 ++-----------------
 sound/soc/sof/intel/hda-dsp.c | 21 +++++++++++++++++----
 sound/soc/sof/intel/hda.h     |  1 +
 sound/soc/sof/intel/icl.c     |  3 ++-
 sound/soc/sof/intel/pci-tgl.c |  2 +-
 sound/soc/sof/intel/tgl.c     | 18 +++++++++++++++++-
 8 files changed, 49 insertions(+), 26 deletions(-)

--
2.25.1

The input MCLK is 12.288MHz, the desired output sysclk is 11.2896MHz
and sample rate is 44100Hz, with the configuration pllprescale=2,
postscale=sysclkdiv=1, some chip may have wrong bclk
and lrclk output with pll enabled in master mode, but with the
configuration pllprescale=1, postscale=2, the output clock is correct.

>From Datasheet, the PLL performs best when f2 is between
90MHz and 100MHz when the desired sysclk output is 11.2896MHz
or 12.288MHz, so sysclkdiv = 2 (f2/8) is the best choice.

So search available sysclk_divs from 2 to 1 other than from 1 to 2.

Fixes: 84fdc00d ("ASoC: codec: wm9860: Refactor PLL out freq search")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1616150926-22892-1-git-send-email-shengjiu.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

ELH is a derivative of TGL, so it should be exposed in tgl.c for
consistency.

No functional change.
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210322163728.16616-9-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

According to hardware spec and PMC FW requirement, the DSP must be
in D3 state before entering S5. Set shutdown call to hda_dsp_shutdown.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210322163728.16616-8-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

According to hardware spec and PMC FW requirement, the DSP must be
in D3 state before entering S5. Set shutdown call to hda_dsp_shutdown.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210322163728.16616-7-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

According to hardware spec and PMC FW requirement, the DSP must be
in D3 state before entering S5. Set shutdown call to hda_dsp_shutdown.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210322163728.16616-6-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

According to hardware spec and PMC FW requirement, the DSP must be
in D3 state before entering S5. Define the shutdown function to use
snd_sof_suspend as shutdown callback to make sure DSP is in D3 state.

Fixes: 44a4cfad ("ASoC: SOF: Intel: tgl: do thorough remove at .shutdown() callback")
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pan Xiuli <xiuli.pan@linux.intel.com>
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210322163728.16616-5-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

EHL is derived from TGL, not CNL, so we shall use the TGL ops.

Fixes: 8d4ba1be ("ASoC: SOF: pci: split PCI into different drivers")
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210322163728.16616-4-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

When the probe is handled in a workqueue, we must use
cancel_work_sync() in the shutdown helper to avoid possible race
conditions.

We must also take care of possible errors happening in a probe
workqueue or during pm_runtime resume (called e.g. before shutdown for
PCI devices). We should really only try to access hardware registers
and initiate IPCs if the DSP is fully booted.

Fixes: daff7f14 ("ASoC: SOF: add snd_sof_device_shutdown() helper for shutdown")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Link: https://lore.kernel.org/r/20210322163728.16616-3-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

When checking for enabled cores it isn't enough to check that
some of the requested cores are running, we have to check that
all of them are.

Fixes: 747503b1 ("ASoC: SOF: Intel: Add Intel specific HDA DSP HW operations")
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210322163728.16616-2-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series "Do not handle MCLK device clock in simple-card-utils" from Sameer Pujar <spujar@nvidia.com>:

With commit 1e30f642 ("ASoC: simple-card-utils: Fix device module clock")
simple-card-utils can control MCLK clock for rate updates or enable/disable.
But this is breaking some platforms where it is expected that codec drivers
would actually handle the MCLK clock. One such example is following platform.
  - "arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var3-ads2.dts"

In above case codec, wm8904, is using internal PLL and configures sysclk
based on fixed MCLK input. In such cases it is expected that, required PLL
output or sysclk, is just passed via set_sysclk() callback and card driver
need not actually update MCLK rate. Instead, codec can take ownership of
this clock and do the necessary configuration.

So the original commit is reverted and codec driver for rt5659 is updated
to fix my board which has this codec.

Sameer Pujar (2):
  ASoC: simple-card-utils: Do not handle device clock
  ASoC: rt5659: Update MCLK rate in set_sysclk()

 sound/soc/codecs/rt5659.c             |  5 +++++
 sound/soc/generic/simple-card-utils.c | 13 +++++++------
 2 files changed, 12 insertions(+), 6 deletions(-)

--
2.7.4

Add compatible string for new added platforms which support spdif module.
They are i.MX8QXP, i.MX8MM, i.MX8MN, i.MX8MQ.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1615884053-4264-1-git-send-email-shengjiu.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

We do some IO operations in the snd_soc_component_set_jack callback
function and snd_soc_component_set_jack() will be called when soc
component is removed. However, we should not access SoundWire registers
when the bus is suspended.
So set regcache_cache_only(regmap, true) to avoid accessing in the
soc component removal process.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20210316005254.29699-1-yung-chuan.liao@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Simple-card/audio-graph-card drivers do not handle MCLK clock when it
is specified in the codec device node. The expectation here is that,
the codec should actually own up the MCLK clock and do necessary setup
in the driver.
Suggested-by: Mark Brown <broonie@kernel.org>
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1615829492-8972-3-git-send-email-spujar@nvidia.comSigned-off-by: Mark Brown <broonie@kernel.org>

This reverts commit 1e30f642 ("ASoC: simple-card-utils: Fix device
module clock"). The original patch ended up breaking following platform,
which depends on set_sysclk() to configure internal PLL on wm8904 codec
and expects simple-card-utils to not update the MCLK rate.
 - "arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var3-ads2.dts"

It would be best if codec takes care of setting MCLK clock via DAI
set_sysclk() callback.
Reported-by: Michael Walle <michael@walle.cc>
Suggested-by: Mark Brown <broonie@kernel.org>
Suggested-by: Michael Walle <michael@walle.cc>
Fixes: 1e30f642 ("ASoC: simple-card-utils: Fix device module clock")
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Tested-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/1615829492-8972-2-git-send-email-spujar@nvidia.comSigned-off-by: Mark Brown <broonie@kernel.org>

This patch correct tdm out bck inverse register to AUDIO_TOP_CON3[3].
Signed-off-by: Jiaxin Yu <jiaxin.yu@mediatek.com>
Link: https://lore.kernel.org/r/1615516005-781-1-git-send-email-jiaxin.yu@mediatek.comSigned-off-by: Mark Brown <broonie@kernel.org>

The max boundary check while parsing dai ids makes
sound card registration fail after common up dai ids.

Fixes: cd3484f7 ("ASoC: qcom: Fix broken support to MI2S TERTIARY and QUATERNARY")
Signed-off-by: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Link: https://lore.kernel.org/r/20210311154557.24978-1-srivasam@codeaurora.orgSigned-off-by: Mark Brown <broonie@kernel.org>

When initialize cadence qspi controller, it is need to set cqspi
to the driver_data field of struct device, because it will be
used in function cqspi_remove/suspend/resume(). Otherwise, there
will be a crash trace as below when invoking these finctions.

Fixes: 31fb632b ("spi: Move cadence-quadspi driver to drivers/spi/")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Link: https://lore.kernel.org/r/20210311091220.3615-1-Meng.Li@windriver.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series "ASoC: sdm845: array out of bound issues" from Srinivas Kandagatla <srinivas.kandagatla@linaro.org>:

During testing John Stultz and Amit reported few array our bound issues
after enabling bound sanitizer

This patch series attempts to fix those!

changes since v1:
	- make sure the wcd is not de-referenced without intialization

Srinivas Kandagatla (3):
  ASoC: qcom: sdm845: Fix array out of bounds access
  ASoC: qcom: sdm845: Fix array out of range on rx slim channels
  ASoC: codecs: wcd934x: add a sanity check in set channel map

 sound/soc/codecs/wcd934x.c | 6 ++++++
 sound/soc/qcom/sdm845.c    | 6 +++---
 2 files changed, 9 insertions(+), 3 deletions(-)

--
2.21.0

The ADSPCS_SPA is Set Power Active bit. To check if DSP is powered
down, we need to check ADSPCS_CPA, the Current Power Active bit.

Fixes: 747503b1 ("ASoC: SOF: Intel: Add Intel specific HDA DSP HW operations")
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pan Xiuli <xiuli.pan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210309004127.4940-1-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

set channel map can be passed with a channel maps, however if
the number of channels that are passed are more than the actual
supported channels then we would be accessing array out of bounds.

So add a sanity check to validate these numbers!

Fixes: a61f3b4f ("ASoC: wcd934x: add support to wcd9340/wcd9341 codec")
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210309142129.14182-4-srinivas.kandagatla@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

WCD934x has only 13 RX SLIM ports however we are setting it as 16
in set_channel_map, this will lead to array out of bounds error!

Orignally caught by enabling USBAN array out of bounds check:

Fixes: 5caf64c6 ("ASoC: qcom: sdm845: add support to DB845c and Lenovo Yoga")
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210309142129.14182-3-srinivas.kandagatla@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Static analysis Coverity had detected a potential array out-of-bounds
write issue due to the fact that MAX AFE port Id was set to 16 instead
of using AFE_PORT_MAX macro.

Fix this by properly using AFE_PORT_MAX macro.

Fixes: 1b93a884 ("ASoC: qcom: sdm845: handle soundwire stream")
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210309142129.14182-2-srinivas.kandagatla@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series "Report jack and button detection + Capture Support" from Lucas Tanure <tanureal@opensource.cirrus.com>:

Hi All,

Here is a patch series for reporting to user space jack and button events and
add the support for Capture. With some cleanups and fixes along the way.

Regards,

Lucas Tanure

Lucas Tanure (12):
  ASoC: cs42l42: Fix Bitclock polarity inversion
  ASoC: cs42l42: Fix channel width support
  ASoC: cs42l42: Fix mixer volume control
  ASoC: cs42l42: Don't enable/disable regulator at Bias Level
  ASoC: cs42l42: Always wait at least 3ms after reset
  ASoC: cs42l42: Remove power if the driver is being removed
  ASoC: cs42l42: Disable regulators if probe fails
  ASoC: cs42l42: Provide finer control on playback path
  ASoC: cs42l42: Set clock source for both ways of stream
  ASoC: cs42l42: Add Capture Support
  ASoC: cs42l42: Report jack and button detection
  ASoC: cs42l42: Use bclk from hw_params if set_sysclk was not called

Richard Fitzgerald (3):
  ASoC: cs42l42: Wait at least 150us after writing SCLK_PRESENT
  ASoC: cs42l42: Only start PLL if it is needed
  ASoC: cs42l42: Wait for PLL to lock before switching to it

 sound/soc/codecs/cs42l42.c | 437 +++++++++++++++++++++----------------
 sound/soc/codecs/cs42l42.h |  41 +++-
 2 files changed, 282 insertions(+), 196 deletions(-)

--
2.30.1

In 61fbeb5d the sirf prima/atlas drivers were removed. This cleans
up a stray header and some Kconfig entries for the codec that
were missed in the process.

Fixes: 61fbeb5d (ASoC: remove sirf prima/atlas drivers)
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210307162338.1160604-1-pbrobinson@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Attempting to use the RX MIX path at 48kHz plays at 96kHz, because these
controls are incorrectly toggling the first bit of the register, which
is part of the FS_RATE field.

Fix the problem by using the same method used by the "WSA RX_MIX EC0_MUX"
control, which is to use SND_SOC_NOPM as the register and use an enum in
the shift field instead.

Fixes: 2c4066e5 ("ASoC: codecs: lpass-wsa-macro: add dapm widgets and route")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210305005049.24726-1-jonathan@marek.caSigned-off-by: Mark Brown <broonie@kernel.org>

An interface can have multiple decimators enabled, so loop over all active
decimators. Otherwise only one channel will be unmuted, and other channels
will be zero. This fixes recording from dual DMIC as a single two channel
stream.

Also remove the now unused "active_decimator" field.

Fixes: 908e6b1d ("ASoC: codecs: lpass-va-macro: Add support to VA Macro")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210304215646.17956-1-jonathan@marek.caSigned-off-by: Mark Brown <broonie@kernel.org>

This delay is part of the power-up sequence defined in the datasheet.
A runtime_resume is a power-up so must also include the delay.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210305173442.195740-6-tanureal@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

dev_pm_ops already enable/disable the codec if not in use
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210305173442.195740-5-tanureal@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

The minimum value is 0x3f (-63dB), which also is mute
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210305173442.195740-4-tanureal@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

Remove the hard coded 32 bits width and replace with the correct width
calculated by params_width.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210305173442.195740-3-tanureal@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

The driver was setting bit clock polarity opposite to intended polarity.
Also simplify the code by grouping ADC and DAC clock configurations into
a single field.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210305173442.195740-2-tanureal@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

Many systems do not use ACPI and hence do not provide a DMI table. On
non-ACPI systems a warning, such as the following, is printed on boot.

 WARNING KERN tegra-audio-graph-card sound: ASoC: no DMI vendor name!

The variable 'dmi_available' is not exported and so currently cannot be
used by kernel modules without adding an accessor. However, it is
possible to use the function is_acpi_device_node() to determine if the
sound card is an ACPI device and hence indicate if we expect a DMI table
to be present. Therefore, call is_acpi_device_node() to see if we are
using ACPI and only parse the DMI table if we are booting with ACPI.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20210303115526.419458-1-jonathanh@nvidia.comSigned-off-by: Mark Brown <broonie@kernel.org>

We only unregister the platform device during the .remove operation,
but if the probe fails we will never reach this sequence.
Suggested-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Fixes: dd96daca ("ASoC: SOF: Intel: Add APL/CNL HW DSP support")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20210302003410.1178535-1-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

Hi All,

Here is a series of rt5640/rt5651 volume-control fixes which I wrote
while working on a bytcr-rt5640 UCM profile patch-series adding
hardware-volume control to devices using this UCM profile.

The UCM series will also work on older kernels, but it works best on
kernels with this series applied, giving e.g. finer grained volume
control and support for hardware muting the outputs.

Regards,

Hans

Hans de Goede (5):
  ASoC: rt5640: Fix dac- and adc- vol-tlv values being off by a factor
    of 10
  ASoC: rt5651: Fix dac- and adc- vol-tlv values being off by a factor
    of 10
  ASoC: rt5640: Add emulated 'DAC1 Playback Switch' control
  ASoC: rt5640: Rename 'Mono DAC Playback Volume' to 'DAC2 Playback
    Volume'
  ASoC: Intel: bytcr_rt5640: Add used AIF to the components string

 sound/soc/codecs/rt5640.c             | 106 +++++++++++++++++++++++---
 sound/soc/codecs/rt5640.h             |   4 +
 sound/soc/codecs/rt5651.c             |   4 +-
 sound/soc/intel/boards/bytcr_rt5640.c |  11 ++-
 4 files changed, 111 insertions(+), 14 deletions(-)

--
2.30.1

Most steps in this table are steps of 3dB (300 centi-dB), so we can
simplify the table.

This not only reduces the amount of space it takes inside the kernel,
this also makes alsa-lib's mixer code actually accept the table, where
as before this change alsa-lib saw the "ADC PGA Gain" control as a
control without a dB scale.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210228160441.241110-1-hdegoede@redhat.comSigned-off-by: Mark Brown <broonie@kernel.org>

According to the SGTL5000 datasheet [1], the DAP_AVC_CTRL register has
the following bit field definitions:

| BITS  | FIELD       | RW | RESET | DEFINITION                        |
| 15    | RSVD        | RO | 0x0   | Reserved                          |
| 14    | RSVD        | RW | 0x1   | Reserved                          |
| 13:12 | MAX_GAIN    | RW | 0x1   | Max Gain of AVC in expander mode  |
| 11:10 | RSVD        | RO | 0x0   | Reserved                          |
| 9:8   | LBI_RESP    | RW | 0x1   | Integrator Response               |
| 7:6   | RSVD        | RO | 0x0   | Reserved                          |
| 5     | HARD_LMT_EN | RW | 0x0   | Enable hard limiter mode          |
| 4:1   | RSVD        | RO | 0x0   | Reserved                          |
| 0     | EN          | RW | 0x0   | Enable/Disable AVC                |

The original default value written to the DAP_AVC_CTRL register during
sgtl5000_i2c_probe() was 0x0510.  This would incorrectly write values to
bits 4 and 10, which are defined as RESERVED.  It would also not set
bits 12 and 14 to their correct RESET values of 0x1, and instead set
them to 0x0.  While the DAP_AVC module is effectively disabled because
the EN bit is 0, this default value is still writing invalid values to
registers that are marked as read-only and RESERVED as well as not
setting bits 12 and 14 to their correct default values as defined by the
datasheet.

The correct value that should be written to the DAP_AVC_CTRL register is
0x5100, which configures the register bits to the default values defined
by the datasheet, and prevents any writes to bits defined as
'read-only'.  Generally speaking, it is best practice to NOT attempt to
write values to registers/bits defined as RESERVED, as it generally
produces unwanted/undefined behavior, or errors.

Also, all credit for this patch should go to my colleague Dan MacDonald
<dmacdonald@curbellmedical.com> for finding this error in the first
place.

[1] https://www.nxp.com/docs/en/data-sheet/SGTL5000.pdfSigned-off-by: Benjamin Rood <benjaminjrood@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210219183308.GA2117@ubuntu-devSigned-off-by: Mark Brown <broonie@kernel.org>