i.MX8MP irqsteer has power-domain support, so use a dedicated compatible.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Verdin I2C2 may be used to access other I2C devices apart from serving
as an HDMI DDC channel.
Thus do not limit the used I2C clock frequency to 10kHz in the module
specific device tree part.
If an overlay configures i2c2 as DDC the overlay is also responsible
to cope with an appropriate I2C clock.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Verdin I2C2 may be used to access other I2C devices apart from serving
as an HDMI DDC channel.
Thus do not limit the used I2C clock frequency to 10kHz in the module
specific device tree part.
If an overlay configures i2c2 as DDC the overlay is also responsible
to cope with an appropriate I2C clock.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

UART2 and UART4 can used in following combination,

2 x RS232:
- UART2 and UART4 without flow control
- MUX selection GPIO3_20 must be held low

1 x RS232 + 1 x RS485:
- UART2 - RS232
- UART4 - RS485
- MUX selection GPIO3_20 must be held high
- RE/DE for RS485 controlled with GPIO3_25

1 x RS232 with flow control:
- UART2 - RS232
- MUX selection GPIO3_20 must be held low
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

I210 intel ethernet controller is connected to PCIe. Enable the PHY
to use the ethernet controller.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Reorder the SAI dma-names to ensure "rx" precedes "tx" as required to fixes
the DTB_CHECK warning.

arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dtb: audio-controller@f100000: dma-names:1: 'tx' was expected
	from schema $id: http://devicetree.org/schemas/sound/fsl,sai.yaml#
arm64/boot/dts/freescale/fsl-ls1028a-rdb.dtb: audio-controller@f110000: dma-names:1: 'tx' was expected
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Remove the undocumented compatible string 'fsl,ls-pcie-ep' property from
the ls1028a device tree source to fix DTB_CHECK warnings.

arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dtb: pcie-ep@3400000: compatible: ['fsl,ls1028a-pcie-ep', 'fsl,ls-pcie-ep'] is too long
	from schema $id: http://devicetree.org/schemas/pci/fsl,layerscape-pcie-ep.yaml#Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The only key that should wake up the phone is power button press. This
prevents accidental wakeup due to e.g. pressing the buttons in the
pocket or backpack and is in line what userspace uses to unblank the
device.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This node is unused and origins from downstream kernel where it is
used for the DSP.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable HDMI output on i.MX8MP DHCOM PDK2 and PDK3. The I2C5 on PDK2 and
I2C mux port 1 on PDK3 respectively are used in regular I2C mode instead
of HDMI DDC mode to permit connection of other I2C devices on those buses.
The pinctrl_hdmi node is part of the SoM DTSI already.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add bt-sco sound card, which is used by BT HFP case.
It supports wb profile as default
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Initialize audio PLL1 as the parent clock for 8kHz series rates,
audio PLL2 as the parent clock for 11kHz series rates. that PLL1
and PLL2 can together support full range of audio sample rates.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

MX8-DLVDS-LCD1 display module integrates a KOE TX26D202VM0BWA LCD panel
and a touch IC.  Add an overlay to support the LCD panel on i.MX8MP EVK.
Specify 148.5MHz clock frequency in panel-timing node to accommodate
3.5-fold 519.75MHz media_ldb clock which is derived from 1.0395GHz
video_pll1 clock.
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the DT node for the GPU core found on the i.MX8QM.

etnaviv-gpu 53100000.gpu: model: GC7000, revision: 6009
[drm] Initialized etnaviv 1.4.0 20151214 for etnaviv on minor 0
Signed-off-by: Christian Gmeiner <cgmeiner@igalia.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add fec2 support.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

add ocotp ad fec_mac[0,1] for imx8qm.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add lsio mu5 and mu6.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add flexcan[1,2,3] support for imx8qm-mek board.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add cm41_i2c and devices under it for imx8qm-mek board.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add i2c0 and all devices under it for imx8qm-mek board.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add cm41 subsystem dtsi for iMX8X chips.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add sai[0,1,6,7], wm8960 and asrc0 support.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add i.MX8QM audio related nodes and update eDMA[0,1]'s information.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Different boards have different DDR memory sizes and layouts for reserved
memory. This change reduces future dependencies to add 'imx8qm-ss-audio'.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add audio nodes for imx8dxl-evk boards.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The power domains of i.MX8DXL's acm is difference i.MX8QXP. IRQ number of
sai[0..3] and spdif0 are also difference.

Update power domains information for i.MX8DXL.

Update sai[0..3] and spdif0's IRQ number for i.MX8DXL.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Delete unused node in adma subsystem.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The bootloader adds MTD partitions in this subnode if present, or in the
spi-nor node itself otherwise.
Setting #size-cells in MTD nodes itself is deprecated by mtd.yaml.
Fix all this by adding an empty partitions node which the bootloader will
fill with configured MTD partitions. Remove the deprecated properties
as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The bootloader adds MTD partitions in this subnode if present, or in the
spi-nor node itself otherwise.
Setting #size-cells in MTD nodes itself is deprecated by mtd.yaml.
Fix all this by adding an empty partitions node which the bootloader will
fill with configured MTD partitions. Remove the deprecated properties
as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The bootloader adds MTD partitions in this subnode if present, or in the
spi-nor node itself otherwise.
Setting #size-cells in MTD nodes itself is deprecated by mtd.yaml.
Fix all this by adding an empty partitions node which the bootloader will
fill with configured MTD partitions. Remove the deprecated properties
as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The bootloader adds MTD partitions in this subnode if present, or in the
spi-nor node itself otherwise.
Setting #size-cells in MTD nodes itself is deprecated by mtd.yaml.
Fix all this by adding an empty partitions node which the bootloader will
fill with configured MTD partitions. Remove the deprecated properties
as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The bootloader adds MTD partitions in this subnode if present, or in the
spi-nor node itself otherwise.
Setting #size-cells in MTD nodes itself is deprecated by mtd.yaml.
Fix all this by adding an empty partitions node which the bootloader will
fill with configured MTD partitions. Remove the deprecated properties
as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The bootloader adds MTD partitions in this subnode if present, or in the
spi-nor node itself otherwise. Direct children cause warnings like:
425e0000.spi: ofpart partition /soc@0/bus@42000000/spi@425e0000/flash@0/
  partition@600000 (/soc@0/bus@42000000/spi@425e0000/flash@0) #size-cells
  is wrongly set to <0>, assuming <1> for parsing partitions.

This is due flexspi node having #size-cells = <0>. Setting #size-cells in
MTD nodes itself is deprecated by mtd.yaml.
Fix all this by adding an empty partitions node which the bootloader will
fill with configured MTD partitions.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds support for both USB host and USB Type-C ports. This includes
the on-board USB hub. Remove the gpio-hog for USB_RESET# as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds support for both USB host and USB Type-C ports. This includes
the on-board USB hub.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The DSI to HDMI bridge supports hot-plut-detect, but the
driver didn't previously support a shared IRQ GPIO.  With
the driver updated, the interrupt can be added to the bridge.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

percpu.h depends on smp.h, but doesn't include it directly because of
circular header dependency issues; percpu.h is needed in a bunch of low
level headers.

This fixes a randconfig build error on mips:

  include/linux/alloc_tag.h: In function '__alloc_tag_ref_set':
  include/asm-generic/percpu.h:31:40: error: implicit declaration of function 'raw_smp_processor_id' [-Werror=implicit-function-declaration]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 24e44cc2 ("mm: percpu: enable per-cpu allocation tagging")
Closes: https://lore.kernel.org/oe-kbuild-all/202405210052.DIrMXJNz-lkp@intel.com/Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'perf-tools-fixes-for-v6.10-1-2024-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools

Pull perf tool fix from Arnaldo Carvalho de Melo:
 "Revert a patch causing a regression.

  This made a simple 'perf record -e cycles:pp make -j199' stop working
  on the Ampere ARM64 system Linus uses to test ARM64 kernels".

* tag 'perf-tools-fixes-for-v6.10-1-2024-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools:
  Revert "perf parse-events: Prefer sysfs/JSON hardware events over legacy"

This reverts commit 617824a7.

This made a simple 'perf record -e cycles:pp make -j199' stop working on
the Ampere ARM64 system Linus uses to test ARM64 kernels, as discussed
at length in the threads in the Link tags below.

The fix provided by Ian wasn't acceptable and work to fix this will take
time we don't have at this point, so lets revert this and work on it on
the next devel cycle.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Cc: Ethan Adams <j.ethan.adams@gmail.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: James Clark <james.clark@arm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Tycho Andersen <tycho@tycho.pizza>
Cc: Yang Jihong <yangjihong@bytedance.com>
Link: https://lore.kernel.org/lkml/CAHk-=wi5Ri=yR2jBVk-4HzTzpoAWOgstr1LEvg_-OXtJvXXJOA@mail.gmail.com
Link: https://lore.kernel.org/lkml/CAHk-=wiWvtFyedDNpoV7a8Fq_FpbB+F5KmWK2xPY3QoYseOf_A@mail.gmail.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>