- 14 Jun, 2017 40 commits
-
-
Rafael J. Wysocki authored
commit 4296f23e upstream. sugov_start() only initializes struct sugov_cpu per-CPU structures for shared policies, but it should do that for single-CPU policies too. That in particular makes the IO-wait boost mechanism work in the cases when cpufreq policies correspond to individual CPUs. Fixes: 21ca6d2c (cpufreq: schedutil: Add iowait boosting) Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
Amit Pundir <amit.pundir@linaro.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Viresh Kumar authored
commit 6c4f0fa6 upstream. cached_raw_freq applies to the entire cpufreq policy and not individual CPUs. Apart from wasting per-cpu memory, it is actually wrong to keep it in struct sugov_cpu as we may end up comparing next_freq with a stale cached_raw_freq of a random CPU. Move cached_raw_freq to struct sugov_policy. Fixes: 5cbea469 (cpufreq: schedutil: map raw required frequency to driver frequency) Signed-off-by:
-
Jani Nikula authored
commit bb1d1329 upstream. The main thing are the DDI ports. If there's a VBT that says there are no outputs, we should trust that, and not have semi-random defaults. Unfortunately, the defaults have resulted in some Chromebooks without VBT to rely on this behaviour, so we split out the defaults for the missing VBT case. Reviewed-by:
Manasi Navare <manasi.d.navare@intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/95c26079ff640d43f53b944f17e9fc356b36daec.1489152288.git.jani.nikula@intel.comSigned-off-by:
-
Jani Nikula authored
commit 66578857 upstream. We don't use the error return for anything other than reporting and logging that there is no VBT. We can pull the logging in the function, and remove the error status return. Moreover, if we needed the information for something later on, we'd probably be better off storing the bit in dev_priv, and using it where it's needed, instead of using the error return. While at it, improve the comments. Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by:
Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
-
Kees Cook authored
commit f5f893c5 upstream. Under SMAP/PAN/etc, we cannot write directly to userspace memory, so this rearranges the test bytes to get written through copy_to_user(). Additionally drops the bad copy_from_user() test that would trigger a memcpy() against userspace on failure. [arnd: the test module was added in 3.14, and this backported patch should apply cleanly on all version from 3.14 to 4.10. The original patch was in 4.11 on top of a context change I saw the bug triggered with kselftest on a 4.4.y stable kernel] Signed-off-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Laura Abbott authored
commit 98562656 upstream. adjust_lowmem_bounds is responsible for setting up the boundary for lowmem/highmem. This needs to be setup before memblock reservations can occur. At the time memblock reservations can occur, memory can also be removed from the system. The lowmem/highmem boundary and end of memory may be affected by this but it is currently not recalculated. On some systems this may be harmless, on others this may result in incorrect ranges being passed to the main memory allocator. Correct this by recalculating the lowmem/highmem boundary after all reservations have been made. Tested-by:
Magnus Lilja <lilja.magnus@gmail.com> Signed-off-by:
Laura Abbott <labbott@redhat.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Cc: Julien Grall <julien.grall@arm.com> Signed-off-by:
-
Laura Abbott authored
commit 374d446d upstream. The logic for sanity_check_meminfo has become difficult to follow. Clean up the code so it's more obvious what the code is actually trying to do. Additionally, meminfo is now removed so rename the function to better describe its purpose. Tested-by:
Nicolas Pitre <nico@linaro.org> Signed-off-by:
Laura Abbott <lauraa@codeaurora.org> Signed-off-by:
-
Kristina Martsenko authored
commit 276e9327 upstream. This backport has a minor difference from the upstream commit: it adds the asm-uaccess.h file, which is not present in 4.9, because 4.9 does not have commit b4b8664d ("arm64: don't pull uaccess.h into *.S"). Original patch description: When handling a data abort from EL0, we currently zero the top byte of the faulting address, as we assume the address is a TTBR0 address, which may contain a non-zero address tag. However, the address may be a TTBR1 address, in which case we should not zero the top byte. This patch fixes that. The effect is that the full TTBR1 address is passed to the task's signal handler (or printed out in the kernel log). When handling a data abort from EL1, we leave the faulting address intact, as we assume it's either a TTBR1 address or a TTBR0 address with tag 0x00. This is true as far as I'm aware, we don't seem to access a tagged TTBR0 address anywhere in the kernel. Regardless, it's easy to forget about address tags, and code added in the future may not always remember to remove tags from addresses before accessing them. So add tag handling to the EL1 data abort handler as well. This also makes it consistent with the EL0 data abort handler. Fixes: d50240a5 ("arm64: mm: permit use of tagged pointers at EL0") Reviewed-by:
Dave Martin <Dave.Martin@arm.com> Acked-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Kristina Martsenko <kristina.martsenko@arm.com> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Kristina Martsenko authored
commit 7dcd9dd8 upstream. This backport has a small difference from the upstream commit: - The address tag is removed in watchpoint_handler() instead of get_distance_from_watchpoint(), because 4.9 does not have commit fdfeff0f ("arm64: hw_breakpoint: Handle inexact watchpoint addresses"). Original patch description: When we take a watchpoint exception, the address that triggered the watchpoint is found in FAR_EL1. We compare it to the address of each configured watchpoint to see which one was hit. The configured watchpoint addresses are untagged, while the address in FAR_EL1 will have an address tag if the data access was done using a tagged address. The tag needs to be removed to compare the address to the watchpoints. Currently we don't remove it, and as a result can report the wrong watchpoint as being hit (specifically, always either the highest TTBR0 watchpoint or lowest TTBR1 watchpoint). This patch removes the tag. Fixes: d50240a5 ("arm64: mm: permit use of tagged pointers at EL0") Acked-by:
Mark Rutland <mark.rutland@arm.com> Acked-by:
-
Kristina Martsenko authored
commit 81cddd65 upstream. This backport has a minor difference from the upstream commit, as v4.9 did not yet have the refactoring done by commit 8b6e70fc ("arm64: traps: correctly handle MRS/MSR with XZR"). Original patch description: When we emulate userspace cache maintenance in the kernel, we can currently send the task a SIGSEGV even though the maintenance was done on a valid address. This happens if the address has a non-zero address tag, and happens to not be mapped in. When we get the address from a user register, we don't currently remove the address tag before performing cache maintenance on it. If the maintenance faults, we end up in either __do_page_fault, where find_vma can't find the VMA if the address has a tag, or in do_translation_fault, where the tagged address will appear to be above TASK_SIZE. In both cases, the address is not mapped in, and the task is sent a SIGSEGV. This patch removes the tag from the address before using it. With this patch, the fault is handled correctly, the address gets mapped in, and the cache maintenance succeeds. As a second bug, if cache maintenance (correctly) fails on an invalid tagged address, the address gets passed into arm64_notify_segfault, where find_vma fails to find the VMA due to the tag, and the wrong si_code may be sent as part of the siginfo_t of the segfault. With this patch, the correct si_code is sent. Fixes: 7dd01aef ("arm64: trap userspace "dc cvau" cache operation on errata-affected core") Acked-by:
-
Takatoshi Akiyama authored
commit 3c910176 upstream. This patch fixes an issue that kernel panic happens when DMA is enabled and we press enter key while the kernel booting on the serial console. * An interrupt may occur after sci_request_irq(). * DMA transfer area is initialized by setup_timer() in sci_request_dma() and used in interrupt. If an interrupt occurred between sci_request_irq() and setup_timer() in sci_request_dma(), DMA transfer area has not been initialized yet. So, this patch changes the order of sci_request_irq() and sci_request_dma(). Fixes: 73a19e4c ("serial: sh-sci: Add DMA support.") Signed-off-by:
Takatoshi Akiyama <takatoshi.akiyama.kj@ps.hitachi-solutions.com> [Shimoda changes the commit log] Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Cc: Jiri Slaby <jslaby@suse.cz> Signed-off-by:
-
Julius Werner authored
commit 32829da5 upstream. A recent fix to /dev/mem prevents mappings from wrapping around the end of physical address space. However, the check was written in a way that also prevents a mapping reaching just up to the end of physical address space, which may be a valid use case (especially on 32-bit systems). This patch fixes it by checking the last mapped address (instead of the first address behind that) for overflow. Fixes: b299cde2 ("drivers: char: mem: Check for address space wraparound with mmap()") Reported-by:
Nico Huber <nico.h@gmx.de> Signed-off-by:
Julius Werner <jwerner@chromium.org> Signed-off-by:
-
Sebastian Andrzej Siewior authored
commit 40da1b11 upstream. If a custom CPU target is specified and that one is not available _or_ can't be interrupted then the code returns to userland without dropping a lock as notices by lockdep: |echo 133 > /sys/devices/system/cpu/cpu7/hotplug/target | ================================================ | [ BUG: lock held when returning to user space! ] | ------------------------------------------------ | bash/503 is leaving the kernel with locks still held! | 1 lock held by bash/503: | #0: (device_hotplug_lock){+.+...}, at: [<ffffffff815b5650>] lock_device_hotplug_sysfs+0x10/0x40 So release the lock then. Fixes: 757c989b ("cpu/hotplug: Make target state writeable") Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20170602142714.3ogo25f2wbq6fjpj@linutronix.deSigned-off-by:
-
Takashi Iwai authored
commit 4efda5f2 upstream. soc_cleanup_card_resources() call snd_card_free() at the last of its procedure. This turned out to lead to a use-after-free. PCM runtimes have been already removed via soc_remove_pcm_runtimes(), while it's dereferenced later in soc_pcm_free() called via snd_card_free(). The fix is simple: just move the snd_card_free() call to the beginning of the whole procedure. This also gives another benefit: it guarantees that all operations have been shut down before actually releasing the resources, which was racy until now. Reported-and-tested-by:
Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Takashi Iwai authored
commit ba3021b2 upstream. snd_timer_user_tselect() reallocates the queue buffer dynamically, but it forgot to reset its indices. Since the read may happen concurrently with ioctl and snd_timer_user_tselect() allocates the buffer via kmalloc(), this may lead to the leak of uninitialized kernel-space data, as spotted via KMSAN: BUG: KMSAN: use of unitialized memory in snd_timer_user_read+0x6c4/0xa10 CPU: 0 PID: 1037 Comm: probe Not tainted 4.11.0-rc5+ #2739 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:16 dump_stack+0x143/0x1b0 lib/dump_stack.c:52 kmsan_report+0x12a/0x180 mm/kmsan/kmsan.c:1007 kmsan_check_memory+0xc2/0x140 mm/kmsan/kmsan.c:1086 copy_to_user ./arch/x86/include/asm/uaccess.h:725 snd_timer_user_read+0x6c4/0xa10 sound/core/timer.c:2004 do_loop_readv_writev fs/read_write.c:716 __do_readv_writev+0x94c/0x1380 fs/read_write.c:864 do_readv_writev fs/read_write.c:894 vfs_readv fs/read_write.c:908 do_readv+0x52a/0x5d0 fs/read_write.c:934 SYSC_readv+0xb6/0xd0 fs/read_write.c:1021 SyS_readv+0x87/0xb0 fs/read_write.c:1018 This patch adds the missing reset of queue indices. Together with the previous fix for the ioctl/read race, we cover the whole problem. Reported-by:
Alexander Potapenko <glider@google.com> Tested-by:
-
Takashi Iwai authored
commit d11662f4 upstream. The read from ALSA timer device, the function snd_timer_user_tread(), may access to an uninitialized struct snd_timer_user fields when the read is concurrently performed while the ioctl like snd_timer_user_tselect() is invoked. We have already fixed the races among ioctls via a mutex, but we seem to have forgotten the race between read vs ioctl. This patch simply applies (more exactly extends the already applied range of) tu->ioctl_lock in snd_timer_user_tread() for closing the race window. Reported-by:
-
Ben Skeggs authored
commit b4e382ca upstream. Reusing the list_head for both is a bad idea. Callback execution is done with the lock dropped so that alarms can be rescheduled from the callback, which means that with some unfortunate timing, lists can get corrupted. The execution list should not require its own locking, the single function that uses it can only be called from a single context. Signed-off-by:
Ben Skeggs <bskeggs@redhat.com> Signed-off-by:
-
Sinclair Yeh authored
commit 07678eca upstream. When vmw_gb_surface_define_ioctl() is called with an existing buffer, we end up returning an uninitialized variable in the backup_handle. The fix is to first initialize backup_handle to 0 just to be sure, and second, when a user-provided buffer is found, we will use the req->buffer_handle as the backup_handle. Reported-by:
Murray McAllister <murray.mcallister@insomniasec.com> Signed-off-by:
Sinclair Yeh <syeh@vmware.com> Reviewed-by:
Deepak Rawat <drawat@vmware.com> Signed-off-by:
-
Vladis Dronov authored
commit ee9c4e68 upstream. The 'req->mip_levels' parameter in vmw_gb_surface_define_ioctl() is a user-controlled 'uint32_t' value which is used as a loop count limit. This can lead to a kernel lockup and DoS. Add check for 'req->mip_levels'. References: https://bugzilla.redhat.com/show_bug.cgi?id=1437431Signed-off-by:
Vladis Dronov <vdronov@redhat.com> Reviewed-by:
-
Dan Carpenter authored
commit f0c62e98 upstream. If vmalloc() fails then we need to a bit of cleanup before returning. Fixes: fb1d9738 ("drm/vmwgfx: Add DRM driver for VMware Virtual GPU") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by:
-
Jin Yao authored
commit cc1582c2 upstream. When doing sampling, for example: perf record -e cycles:u ... On workloads that do a lot of kernel entry/exits we see kernel samples, even though :u is specified. This is due to skid existing. This might be a security issue because it can leak kernel addresses even though kernel sampling support is disabled. The patch drops the kernel samples if exclude_kernel is specified. For example, test on Haswell desktop: perf record -e cycles:u <mgen> perf report --stdio Before patch applied: 99.77% mgen mgen [.] buf_read 0.20% mgen mgen [.] rand_buf_init 0.01% mgen [kernel.vmlinux] [k] apic_timer_interrupt 0.00% mgen mgen [.] last_free_elem 0.00% mgen libc-2.23.so [.] __random_r 0.00% mgen libc-2.23.so [.] _int_malloc 0.00% mgen mgen [.] rand_array_init 0.00% mgen [kernel.vmlinux] [k] page_fault 0.00% mgen libc-2.23.so [.] __random 0.00% mgen libc-2.23.so [.] __strcasestr 0.00% mgen ld-2.23.so [.] strcmp 0.00% mgen ld-2.23.so [.] _dl_start 0.00% mgen libc-2.23.so [.] sched_setaffinity@@GLIBC_2.3.4 0.00% mgen ld-2.23.so [.] _start We can see kernel symbols apic_timer_interrupt and page_fault. After patch applied: 99.79% mgen mgen [.] buf_read 0.19% mgen mgen [.] rand_buf_init 0.00% mgen libc-2.23.so [.] __random_r 0.00% mgen mgen [.] rand_array_init 0.00% mgen mgen [.] last_free_elem 0.00% mgen libc-2.23.so [.] vfprintf 0.00% mgen libc-2.23.so [.] rand 0.00% mgen libc-2.23.so [.] __random 0.00% mgen libc-2.23.so [.] _int_malloc 0.00% mgen libc-2.23.so [.] _IO_doallocbuf 0.00% mgen ld-2.23.so [.] do_lookup_x 0.00% mgen ld-2.23.so [.] open_verify.constprop.7 0.00% mgen ld-2.23.so [.] _dl_important_hwcaps 0.00% mgen libc-2.23.so [.] sched_setaffinity@@GLIBC_2.3.4 0.00% mgen ld-2.23.so [.] _start There are only userspace symbols. Signed-off-by:
Jin Yao <yao.jin@linux.intel.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: acme@kernel.org Cc: jolsa@kernel.org Cc: kan.liang@intel.com Cc: mark.rutland@arm.com Cc: will.deacon@arm.com Cc: yao.jin@intel.com Link: http://lkml.kernel.org/r/1495706947-3744-1-git-send-email-yao.jin@linux.intel.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Breno Leitao authored
commit 7f22ced4 upstream. Currently tsk->thread.load_tm is not initialized in the task creation and can contain garbage on a new task. This is an undesired behaviour, since it affects the timing to enable and disable the transactional memory laziness (disabling and enabling the MSR TM bit, which affects TM reclaim and recheckpoint in the scheduling process). Fixes: 5d176f75 ("powerpc: tm: Enable transactional memory (TM) lazily for userspace") Signed-off-by:
Breno Leitao <leitao@debian.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Breno Leitao authored
commit 1195892c upstream. Currently tsk->thread->load_vec and load_fp are not initialized during task creation, which can lead to garbage values in these variables (non-zero values). These variables will be checked later in restore_math() to validate if the FP and vector registers are being utilized. Since these values might be non-zero, the restore_math() will continue to save the FP and vectors even if they were never utilized by the userspace application. load_fp and load_vec counters will then overflow (they wrap at 255) and the FP and Altivec will be finally disabled, but before that condition is reached (counter overflow) several context switches will have restored FP and vector registers without need, causing a performance degradation. Fixes: 70fe3d98 ("powerpc: Restore FPU/VEC/VSX if previously used") Signed-off-by:
Gustavo Romero <gusbromero@gmail.com> Acked-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
-
Michael Bringmann authored
commit dc421b20 upstream. When adding or removing memory, the aa_index (affinity value) for the memblock must also be converted to match the endianness of the rest of the 'ibm,dynamic-memory' property. Otherwise, subsequent retrieval of the attribute will likely lead to non-existent nodes, followed by using the default node in the code inappropriately. Fixes: 5f97b2a0 ("powerpc/pseries: Implement memory hotplug add in the kernel") Signed-off-by:
Michael Bringmann <mwb@linux.vnet.ibm.com> Signed-off-by:
-
Michael Ellerman authored
commit ba4a648f upstream. In commit 8c272261 ("powerpc/numa: Enable USE_PERCPU_NUMA_NODE_ID"), we switched to the generic implementation of cpu_to_node(), which uses a percpu variable to hold the NUMA node for each CPU. Unfortunately we neglected to notice that we use cpu_to_node() in the allocation of our percpu areas, leading to a chicken and egg problem. In practice what happens is when we are setting up the percpu areas, cpu_to_node() reports that all CPUs are on node 0, so we allocate all percpu areas on node 0. This is visible in the dmesg output, as all pcpu allocs being in group 0: pcpu-alloc: [0] 00 01 02 03 [0] 04 05 06 07 pcpu-alloc: [0] 08 09 10 11 [0] 12 13 14 15 pcpu-alloc: [0] 16 17 18 19 [0] 20 21 22 23 pcpu-alloc: [0] 24 25 26 27 [0] 28 29 30 31 pcpu-alloc: [0] 32 33 34 35 [0] 36 37 38 39 pcpu-alloc: [0] 40 41 42 43 [0] 44 45 46 47 To fix it we need an early_cpu_to_node() which can run prior to percpu being setup. We already have the numa_cpu_lookup_table we can use, so just plumb it in. With the patch dmesg output shows two groups, 0 and 1: pcpu-alloc: [0] 00 01 02 03 [0] 04 05 06 07 pcpu-alloc: [0] 08 09 10 11 [0] 12 13 14 15 pcpu-alloc: [0] 16 17 18 19 [0] 20 21 22 23 pcpu-alloc: [1] 24 25 26 27 [1] 28 29 30 31 pcpu-alloc: [1] 32 33 34 35 [1] 36 37 38 39 pcpu-alloc: [1] 40 41 42 43 [1] 44 45 46 47 We can also check the data_offset in the paca of various CPUs, with the fix we see: CPU 0: data_offset = 0x0ffe8b0000 CPU 24: data_offset = 0x1ffe5b0000 And we can see from dmesg that CPU 24 has an allocation on node 1: node 0: [mem 0x0000000000000000-0x0000000fffffffff] node 1: [mem 0x0000001000000000-0x0000001fffffffff] Fixes: 8c272261 ("powerpc/numa: Enable USE_PERCPU_NUMA_NODE_ID") Signed-off-by:
Nicholas Piggin <npiggin@gmail.com> Signed-off-by:
-
Christophe Leroy authored
commit 6f553912 upstream. of_mm_gpiochip_add_data() generates an oops for NULL pointer dereference. of_mm_gpiochip_add_data() calls mm_gc->save_regs() before setting the data, therefore ->save_regs() cannot use gpiochip_get_data() Fixes: 937daafc ("powerpc: simple-gpio: use gpiochip data pointer") Signed-off-by:
Christophe Leroy <christophe.leroy@c-s.fr> Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Joe Carnuccio authored
commit 74939a0b upstream. Signed-off-by:
Joe Carnuccio <joe.carnuccio@cavium.com> Signed-off-by:
Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Joe Carnuccio authored
commit 1d634965 upstream. Set bit (BIT_15) to send right ECHO payload information for Diagnostic Echo Test command. Signed-off-by:
-
Joe Carnuccio authored
commit ce6c668b upstream. Firmware dump allows for debugging customer issues. This patch fixes start/end pointer calculation to capture T262 template entry for dump tool. Signed-off-by:
-
Johannes Thumshirn authored
commit ddff7ed4 upstream. When pci_enable_device() or pci_enable_device_mem() fail in qla2x00_probe_one() we bail out but do a call to pci_disable_device(). This causes the dev_WARN_ON() in pci_disable_device() to trigger, as the device wasn't enabled previously. So instead of taking the 'probe_out' error path we can directly return *iff* one of the pci_enable_device() calls fails. Additionally rename the 'probe_out' goto label's name to the more descriptive 'disable_device'. Signed-off-by:
Johannes Thumshirn <jthumshirn@suse.de> Fixes: e315cd28 ("[SCSI] qla2xxx: Code changes for qla data structure refactoring") Reviewed-by:
Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by:
Giridhar Malavali <giridhar.malavali@cavium.com> Signed-off-by:
-
Marc Zyngier authored
commit d6dbdd3c upstream. Under memory pressure, we start ageing pages, which amounts to parsing the page tables. Since we don't want to allocate any extra level, we pass NULL for our private allocation cache. Which means that stage2_get_pud() is allowed to fail. This results in the following splat: [ 1520.409577] Unable to handle kernel NULL pointer dereference at virtual address 00000008 [ 1520.417741] pgd = ffff810f52fef000 [ 1520.421201] [00000008] *pgd=0000010f636c5003, *pud=0000010f56f48003, *pmd=0000000000000000 [ 1520.429546] Internal error: Oops: 96000006 [#1] PREEMPT SMP [ 1520.435156] Modules linked in: [ 1520.438246] CPU: 15 PID: 53550 Comm: qemu-system-aar Tainted: G W 4.12.0-rc4-00027-g1885c397eaec #7205 [ 1520.448705] Hardware name: FOXCONN R2-1221R-A4/C2U4N_MB, BIOS G31FB12A 10/26/2016 [ 1520.463726] task: ffff800ac5fb4e00 task.stack: ffff800ce04e0000 [ 1520.469666] PC is at stage2_get_pmd+0x34/0x110 [ 1520.474119] LR is at kvm_age_hva_handler+0x44/0xf0 [ 1520.478917] pc : [<ffff0000080b137c>] lr : [<ffff0000080b149c>] pstate: 40000145 [ 1520.486325] sp : ffff800ce04e33d0 [ 1520.489644] x29: ffff800ce04e33d0 x28: 0000000ffff40064 [ 1520.494967] x27: 0000ffff27e00000 x26: 0000000000000000 [ 1520.500289] x25: ffff81051ba65008 x24: 0000ffff40065000 [ 1520.505618] x23: 0000ffff40064000 x22: 0000000000000000 [ 1520.510947] x21: ffff810f52b20000 x20: 0000000000000000 [ 1520.516274] x19: 0000000058264000 x18: 0000000000000000 [ 1520.521603] x17: 0000ffffa6fe7438 x16: ffff000008278b70 [ 1520.526940] x15: 000028ccd8000000 x14: 0000000000000008 [ 1520.532264] x13: ffff7e0018298000 x12: 0000000000000002 [ 1520.537582] x11: ffff000009241b93 x10: 0000000000000940 [ 1520.542908] x9 : ffff0000092ef800 x8 : 0000000000000200 [ 1520.548229] x7 : ffff800ce04e36a8 x6 : 0000000000000000 [ 1520.553552] x5 : 0000000000000001 x4 : 0000000000000000 [ 1520.558873] x3 : 0000000000000000 x2 : 0000000000000008 [ 1520.571696] x1 : ffff000008fd5000 x0 : ffff0000080b149c [ 1520.577039] Process qemu-system-aar (pid: 53550, stack limit = 0xffff800ce04e0000) [...] [ 1521.510735] [<ffff0000080b137c>] stage2_get_pmd+0x34/0x110 [ 1521.516221] [<ffff0000080b149c>] kvm_age_hva_handler+0x44/0xf0 [ 1521.522054] [<ffff0000080b0610>] handle_hva_to_gpa+0xb8/0xe8 [ 1521.527716] [<ffff0000080b3434>] kvm_age_hva+0x44/0xf0 [ 1521.532854] [<ffff0000080a58b0>] kvm_mmu_notifier_clear_flush_young+0x70/0xc0 [ 1521.539992] [<ffff000008238378>] __mmu_notifier_clear_flush_young+0x88/0xd0 [ 1521.546958] [<ffff00000821eca0>] page_referenced_one+0xf0/0x188 [ 1521.552881] [<ffff00000821f36c>] rmap_walk_anon+0xec/0x250 [ 1521.558370] [<ffff000008220f78>] rmap_walk+0x78/0xa0 [ 1521.563337] [<ffff000008221104>] page_referenced+0x164/0x180 [ 1521.569002] [<ffff0000081f1af0>] shrink_active_list+0x178/0x3b8 [ 1521.574922] [<ffff0000081f2058>] shrink_node_memcg+0x328/0x600 [ 1521.580758] [<ffff0000081f23f4>] shrink_node+0xc4/0x328 [ 1521.585986] [<ffff0000081f2718>] do_try_to_free_pages+0xc0/0x340 [ 1521.592000] [<ffff0000081f2a64>] try_to_free_pages+0xcc/0x240 [...] The trivial fix is to handle this NULL pud value early, rather than dereferencing it blindly. Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Reviewed-by:
Christoffer Dall <cdall@linaro.org> Signed-off-by:
-
Jeff Mahoney authored
commit 896533a7 upstream. If we fail to add the space_info kobject, we'll leak the memory for the percpu counter. Fixes: 6ab0a202 (btrfs: publish allocation data in sysfs) Signed-off-by:
Jeff Mahoney <jeffm@suse.com> Reviewed-by:
Liu Bo <bo.li.liu@oracle.com> Signed-off-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
David Sterba authored
commit cc2b702c upstream. Variables start_idx and end_idx are supposed to hold a page index derived from the file offsets. The int type is not the right one though, offsets larger than 1 << 44 will get silently trimmed off the high bits. (1 << 44 is 16TiB) What can go wrong, if start is below the boundary and end gets trimmed: - if there's a page after start, we'll find it (radix_tree_gang_lookup_slot) - the final check "if (page->index <= end_idx)" will unexpectedly fail The function will return false, ie. "there's no page in the range", although there is at least one. btrfs_page_exists_in_range is used to prevent races in: * in hole punching, where we make sure there are not pages in the truncated range, otherwise we'll wait for them to finish and redo truncation, but we're going to replace the pages with holes anyway so the only problem is the intermediate state * lock_extent_direct: we want to make sure there are no pages before we lock and start DIO, to prevent stale data reads For practical occurence of the bug, there are several constaints. The file must be quite large, the affected range must cross the 16TiB boundary and the internal state of the file pages and pending operations must match. Also, we must not have started any ordered data in the range, otherwise we don't even reach the buggy function check. DIO locking tries hard in several places to avoid deadlocks with buffered IO and avoids waiting for ranges. The worst consequence seems to be stale data read. CC: Liu Bo <bo.li.liu@oracle.com> Fixes: fc4adbff ("btrfs: Drop EXTENT_UPTODATE check in hole punching and direct locking") Reviewed-by:
-
Vaibhav Jain authored
commit b3aa20ba upstream. During an eeh call to cxl_remove can result in double free_irq of psl,slice interrupts. This can happen if perst_reloads_same_image == 1 and call to cxl_configure_adapter() fails during slot_reset callback. In such a case we see a kernel oops with following back-trace: Oops: Kernel access of bad area, sig: 11 [#1] Call Trace: free_irq+0x88/0xd0 (unreliable) cxl_unmap_irq+0x20/0x40 [cxl] cxl_native_release_psl_irq+0x78/0xd8 [cxl] pci_deconfigure_afu+0xac/0x110 [cxl] cxl_remove+0x104/0x210 [cxl] pci_device_remove+0x6c/0x110 device_release_driver_internal+0x204/0x2e0 pci_stop_bus_device+0xa0/0xd0 pci_stop_and_remove_bus_device+0x28/0x40 pci_hp_remove_devices+0xb0/0x150 pci_hp_remove_devices+0x68/0x150 eeh_handle_normal_event+0x140/0x580 eeh_handle_event+0x174/0x360 eeh_event_handler+0x1e8/0x1f0 This patch fixes the issue of double free_irq by checking that variables that hold the virqs (err_hwirq, serr_hwirq, psl_virq) are not '0' before un-mapping and resetting these variables to '0' when they are un-mapped. Signed-off-by:
Vaibhav Jain <vaibhav@linux.vnet.ibm.com> Reviewed-by:
Andrew Donnellan <andrew.donnellan@au1.ibm.com> Acked-by:
Frederic Barrat <fbarrat@linux.vnet.ibm.com> Signed-off-by:
-
Frederic Barrat authored
commit cec422c1 upstream. Fix error path if we can't copy user structure on CXL_IOCTL_START_WORK ioctl. We shouldn't unlock the context status mutex as it was not locked (yet). Fixes: 0712dc7e ("cxl: Fix issues when unmapping contexts") Signed-off-by:
-
Al Viro authored
commit 006351ac upstream. Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Al Viro authored
commit 940ef1a0 upstream. ... and it really needs splitting into "new" and "extend" cases, but that's for later Signed-off-by:
-
Al Viro authored
commit 6b0d144f upstream. Signed-off-by:
-
Al Viro authored
commit eb315d2a upstream. Signed-off-by:
-
Al Viro authored
commit 414cf718 upstream. Signed-off-by:
-
