- 02 Jan, 2024 40 commits
-
-
Andrii Staikov authored
Switchdev mode allows to add mirroring rules to mirror incoming and outgoing packets to the interface's port representor. Previously, this was available only using software functionality. Add possibility to offload this functionality to the NIC hardware. Introduce ICE_MIRROR_PACKET filter action to the ice_sw_fwd_act_type enum to identify the desired action and pass it to the hardware as well as the VSI to mirror. Example of tc mirror command using hardware: tc filter add dev ens1f0np0 ingress protocol ip prio 1 flower src_mac b4:96:91:a5:c7:a7 skip_sw action mirred egress mirror dev eth1 ens1f0np0 - PF b4:96:91:a5:c7:a7 - source MAC address eth1 - PR of a VF to mirror to Co-developed-by:
Marcin Szycik <marcin.szycik@intel.com> Signed-off-by:
Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by:
Andrii Staikov <andrii.staikov@intel.com> Tested-by:
Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com>
-
Karol Kolacinski authored
Introduce new capability - Low Latency Timestamping with Interrupt. On supported devices, driver can request a single timestamp from FW without polling the register afterwards. Instead, FW can issue a dedicated interrupt when the timestamp was read from the PHY register and its value is available to read from the register. This eliminates the need of bottom half scheduling, which results in minimal delay for timestamping. For this mode, allocate TS indices sequentially, so that timestamps are always completed in FIFO manner. Co-developed-by:
Yochai Hagvi <yochai.hagvi@intel.com> Signed-off-by:
Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by:
Karol Kolacinski <karol.kolacinski@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by:
-
Karol Kolacinski authored
Schedule service task and EXTTS in the top half to avoid bottom half scheduling if possible, which significantly reduces timestamping delay. Co-developed-by:
Michal Michalik <michal.michalik@intel.com> Signed-off-by:
-
David S. Miller authored
Jamal Hadi Salim says: ==================== net/sched: Remove UAPI support for retired TC qdiscs and classifiers Classifiers RSVP and tcindex as well as qdiscs dsmark, CBQ and ATM have already been deleted. This patchset removes their UAPI support. User space - with a focus on iproute2 - typically copies these UAPI headers for different kernels. These deletion patches are coordinated with the iproute2 maintainers to make sure that they delete any user space code referencing removed objects at their leisure. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Jamal Hadi Salim authored
Commit 051d4420 ("net/sched: Retire CBQ qdisc") retired the CBQ qdisc. Remove UAPI for it. Iproute2 will sync by equally removing it from user space. Reviewed-by:
Victor Nogueira <victor@mojatatu.com> Reviewed-by:
Pedro Tammela <pctammela@mojatatu.com> Signed-off-by:
Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by:
-
Jamal Hadi Salim authored
Commit fb38306c ("net/sched: Retire ATM qdisc") retired the ATM qdisc. Remove UAPI for it. Iproute2 will sync by equally removing it from user space. Reviewed-by:
-
Jamal Hadi Salim authored
Commit bbe77c14 ("net/sched: Retire dsmark qdisc") retired the dsmark classifier. Remove UAPI support for it. Iproute2 will sync by equally removing it from user space. Reviewed-by:
-
Jamal Hadi Salim authored
commit 8c710f75 ("net/sched: Retire tcindex classifier") retired the TC tcindex classifier. Remove UAPI for it. Iproute2 will sync by equally removing it from user space. Reviewed-by:
-
Jamal Hadi Salim authored
commit 265b4da8 ("net/sched: Retire rsvp classifier") retired the TC RSVP classifier. Remove UAPI for it. Iproute2 will sync by equally removing it from user space. Reviewed-by:
-
David S. Miller authored
Shinas Rasheed says: ==================== add octeon_ep_vf driver This driver implements networking functionality of Marvell's Octeon PCI Endpoint NIC VF. This driver support following devices: * Network controller: Cavium, Inc. Device b203 * Network controller: Cavium, Inc. Device b403 * Network controller: Cavium, Inc. Device b103 * Network controller: Cavium, Inc. Device b903 * Network controller: Cavium, Inc. Device ba03 * Network controller: Cavium, Inc. Device bc03 * Network controller: Cavium, Inc. Device bd03 Changes: V2: - Removed linux/version.h header file from inclusion in octep_vf_main.c - Corrected Makefile entry to include building octep_vf_mbox.c in [6/8] patch. - Removed redundant vzalloc pointer cast and vfree pointer check in [6/8] patch. V1: https://lore.kernel.org/all/20231221092844.2885872-1-srasheed@marvell.com/ ==================== Signed-off-by: -
Shinas Rasheed authored
add MAINTAINERS for octeon_ep_vf driver. Signed-off-by:
Shinas Rasheed <srasheed@marvell.com> Signed-off-by:
-
Shinas Rasheed authored
Add support for the following ethtool commands: ethtool -i|--driver devname ethtool devname ethtool -S|--statistics devname Signed-off-by:
-
Shinas Rasheed authored
Add support to enable MSI-x and register interrupts. Add support to process Tx and Rx traffic. Includes processing Tx completions and Rx refill. Signed-off-by:
-
Shinas Rasheed authored
Add support for ndo ops to set MAC address, change MTU, get stats. Add control path support to set MAC address, change MTU, get stats, set speed, get and set link mode. Signed-off-by:
-
Shinas Rasheed authored
Implement Tx/Rx ring resource allocation and cleanup. Signed-off-by:
-
Shinas Rasheed authored
Implement VF-PF mailbox to send all control commands from VF to PF and receive responses and notifications from PF to VF. Signed-off-by:
-
Shinas Rasheed authored
Implement hardware resource init and shutdown helper APIs, like hardware Tx/Rx queue init/enable/disable/reset. Signed-off-by:
-
Shinas Rasheed authored
Add driver framework and device setup and initialization for Octeon PCI Endpoint NIC VF. Add implementation to load module, initialize, register network device, cleanup and unload module. Signed-off-by:
-
Geoff Levand authored
In an effort to make the PS3 gelic driver easier to maintain, create two new structures, struct gelic_hw_regs and struct gelic_chain_link, and replace the corresponding members of struct gelic_descr with the new structures. The new struct gelic_hw_regs holds the register variables used by the gelic hardware device. The new struct gelic_chain_link holds variables used to manage the driver's linked list of gelic descr structures. Signed-off-by:
Geoff Levand <geoff@infradead.org> Signed-off-by:
-
David S. Miller authored
Michael Chan says: ==================== bnxt_en: Add basic ntuple filter support The current driver only supports ntuple filters added by aRFS. This patch series adds basic support for user defined TCP/UDP ntuple filters added by the user using ethtool. Many of the patches are refactoring patches to make the existing code more general to support both aRFS and user defined filters. aRFS filters always have the Toeplitz hash value from the NIC. A Toepliz hash function is added in patch 5 to get the same hash value for user defined filters. The hash is used to store all ntuple filters in the table and all filters must be hashed identically using the same function and key. v2: Fix compile error in patch #4 when CONFIG_BNXT_SRIOV is disabled. ==================== Signed-off-by: -
Michael Chan authored
Add logic to delete a user specified ntuple filter from ethtool. Reviewed-by:
Vasundhara Volam <vasundhara-v.volam@broadcom.com> Reviewed-by:
Andy Gospodarek <andrew.gospodarek@broadcom.com> Reviewed-by:
Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Michael Chan authored
Add support for adding user defined ntuple TCP/UDP filters. These filters are similar to aRFS filters except that they don't get aged. Source IP, destination IP, source port, or destination port can be unspecifed as wildcard. At least one of these tuples must be specifed. If a tuple is specified, the full mask must be specified. All ntuple related ethtool functions are now no longer compiled only for CONFIG_RFS_ACCEL. Reviewed-by:
-
Michael Chan authored
aRFS filters match all 5 tuples. User defined ntuple filters may specify some of the tuples as wildcards. To support that, we add the ntuple_flags to the bnxt_ntuple_filter struct to specify which tuple fields are to be matched. The matching tuple fields will then be passed to the firmware in bnxt_hwrm_cfa_ntuple_filter_alloc() to create the proper filter. Reviewed-by:
-
Michael Chan authored
Refactor the logic into a new function bnxt_del_ntp_filters(). The same call will be used when the user deletes an ntuple filter. The bnxt_hwrm_cfa_ntuple_filter_free() function to call fw to free the ntuple filter is exported so that the ethtool logic can call it. Reviewed-by:
Simon Horman <horms@kernel.org> Signed-off-by:
-
Michael Chan authored
Generalize the ethtool logic that walks the ntuple hash table now that we have the common bnxt_filter_base structure. This will allow the code to easily extend to cover user defined ntuple or ether filters. Reviewed-by:
-
Michael Chan authored
Add a new function bnxt_insert_ntp_filter() to insert the ntuple filter into the hash table and other basic setup. We'll use this function to insert a user defined filter from ethtool. Also, export bnxt_lookup_ntp_filter_from_idx() and bnxt_get_ntp_filter_idx() for similar purposes. All ntuple related functions are now no longer compiled only for CONFIG_RFS_ACCEL Reviewed-by:
-
Michael Chan authored
Change the unused flag to BNXT_FLTR_INSERTED. To prepare for multiple pathways that an ntuple filter can be deleted, we add this flag. These filter structures can be retreived from the RCU hash table but only the caller that sees that the BNXT_FLTR_INSERTED flag is set can delete the filter structure and clear the flag under spinlock. Reviewed-by:
-
Michael Chan authored
Add the helper function to look up the ntuple filter from the hash index and use it in bnxt_rx_flow_steer(). The helper function will also be used by user defined ntuple filters in the next patches. Reviewed-by:
-
Pavan Chebbi authored
For ntuple filters added by aRFS, the Toeplitz hash calculated by our NIC is available and is used to store the ntuple filter for quick retrieval. In the next patches, user defined ntuple filter support will be added and we need to calculate the same hash for these filters. The same hash function needs to be used so we can detect duplicates. Add the function bnxt_toeplitz() to calculate the Toeplitz hash for user defined ntuple filters. bnxt_toeplitz() uses the same Toeplitz key and the same key length as the NIC. bnxt_get_ntp_filter_idx() is added to return the hash index. For aRFS, the hash comes from the NIC. For user defined ntuple, we call bnxt_toeplitz() to calculate the hash index. Reviewed-by:
-
Michael Chan authored
Refactor the L2 filter alloc/free logic so that these filters can be added/deleted by the user. The bp->ntp_fltr_bmap allocated size is also increased to allow enough IDs for L2 filters. Reviewed-by:
-
Michael Chan authored
With the new bnxt_l2_filter structure, we can now re-structure the bnxt_ntuple_filter structure to point to the bnxt_l2_filter structure. We eliminate the L2 ether address info from the ntuple filter structure as we can get the information from the L2 filter structure. Note that the source L2 MAC address is no longer used. Reviewed-by:
-
Michael Chan authored
The current driver only has an array of 4 additional L2 unicast addresses to support the netdev uc address list. Generalize and expand this infrastructure with an L2 address hash table so we can support an expanded list of unicast addresses (for bridges, macvlans, OVS, etc). The L2 hash table infrastructure will also allow more generalized n-tuple filter support. This patch creates the bnxt_l2_filter structure and the hash table. This L2 filter structure has the same bnxt_filter_base structure as used in the bnxt_ntuple_filter structure. All currently supported L2 filters will now have an entry in this new table. Note that L2 filters may be created for the VF. VF filters should not be freed when the PF goes down. Add some logic in bnxt_free_l2_filters() to allow keeping the VF filters or to free everything during rmmod. Reviewed-by:
-
Michael Chan authored
This is in preparation to support user defined L2 (ether) filters, which will have many similarities with ntuple filters. Refactor bnxt_ntuple_filter structure to have a bnxt_filter_base structure that can be re-used by the L2 filters. Reviewed-by:
-
David S. Miller authored
Merge tag 'for-net-next-2023-12-22' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next Luiz Augusto von Dentz says: ==================== bluetooth-next pull request for net-next: - btnxpuart: Fix recv_buf return value - L2CAP: Fix responding with multiple rejects - Fix atomicity violation in {min,max}_key_size_set - ISO: Allow binding a PA sync socket - ISO: Reassociate a socket with an active BIS - ISO: Avoid creating child socket if PA sync is terminating - Add device 13d3:3572 IMC Networks Bluetooth Radio - Don't suspend when there are connections - Remove le_restart_scan work - Fix bogus check for re-auth not supported with non-ssp - lib: Add documentation to exported functions - Support HFP offload for QCA2066 ==================== Signed-off-by:
-
Vegard Nossum authored
Commit f061c9f7 ("Documentation: Document each netlink family") added a new Python script that is invoked during 'make htmldocs' and which reads the netlink YAML spec files. Using the virtualenv from scripts/sphinx-pre-install, we get this new error wen running 'make htmldocs': Traceback (most recent call last): File "./tools/net/ynl/ynl-gen-rst.py", line 26, in <module> import yaml ModuleNotFoundError: No module named 'yaml' make[2]: *** [Documentation/Makefile:112: Documentation/networking/netlink_spec/rt_link.rst] Error 1 make[1]: *** [Makefile:1708: htmldocs] Error 2 Fix this by adding 'pyyaml' to requirements.txt. Note: This was somehow present in the original patch submission: <https://lore.kernel.org/all/20231103135622.250314-1-leitao@debian.org/> I'm not sure why the pyyaml requirement disappeared in the meantime. Fixes: f061c9f7 ("Documentation: Document each netlink family") Cc: Breno Leitao <leitao@debian.org> Cc: Jakub Kicinski <kuba@kernel.org> Cc: David S. Miller <davem@davemloft.net> Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by:
Vegard Nossum <vegard.nossum@oracle.com> Reviewed-by:
-
David S. Miller authored
Matthieu Baerts says: ==================== mptcp: add CurrEstab MIB counter This MIB counter is similar to the one of TCP -- CurrEstab -- available in /proc/net/snmp. This is useful to quickly list the number of MPTCP connections without having to iterate over all of them. Patch 1 prepares its support by adding new helper functions: - MPTCP_DEC_STATS(): similar to MPTCP_INC_STATS(), but this time to decrement a counter. - mptcp_set_state(): similar to tcp_set_state(), to change the state of an MPTCP socket, and to inc/decrement the new counter when needed. Patch 2 uses mptcp_set_state() instead of directly calling inet_sk_state_store() to change the state of MPTCP sockets. Patch 3 and 4 validate the new feature in MPTCP "join" and "diag" selftests. ==================== Signed-off-by:
Matthieu Baerts <matttbe@kernel.org> Signed-off-by:
-
Geliang Tang authored
This patch adds a new helper chk_msk_cestab() to check the current established connections counter MIB_CURRESTAB in diag.sh. Invoke it to check the counter during the connection after every chk_msk_inuse(). Signed-off-by:
Geliang Tang <geliang.tang@linux.dev> Reviewed-by:
-
Geliang Tang authored
This patch adds a new helper chk_cestab_nr() to check the current established connections counter MIB_CURRESTAB. Set the newly added variables cestab_ns1 and cestab_ns2 to indicate how many connections are expected in ns1 or ns2. Invoke check_cestab() to check the counter during the connection in do_transfer() and invoke chk_cestab_nr() to re-check it when the connection closed. These checks are embedded in add_tests(). Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Reviewed-by:
-
Geliang Tang authored
This patch replaces all the 'inet_sk_state_store()' calls under net/mptcp with the new helper mptcp_set_state(). Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/460Signed-off-by:
-
Geliang Tang authored
Add a new MIB counter named MPTCP_MIB_CURRESTAB to count current established MPTCP connections, similar to TCP_MIB_CURRESTAB. This is useful to quickly list the number of MPTCP connections without having to iterate over all of them. This patch adds a new helper function mptcp_set_state(): if the state switches from or to ESTABLISHED state, this newly added counter is incremented. This helper is going to be used in the following patch. Similar to MPTCP_INC_STATS(), a new helper called MPTCP_DEC_STATS() is also needed to decrement a MIB counter. Signed-off-by:
-
